Material Safety Data Sheet

Size: px

Start display at page:

Download "Material Safety Data Sheet"

Stuart Richards
6 years ago
Views:

1 Page 1 of 6 Material Safety Data Sheet SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION: 1.1 Product Name: EGS Mortar & Grout System (Part A) 100% Epoxy 1.2 Company Identification: Southern Grouts and Mortars, Inc SW 2nd Place Pompano Beach, Florida (954) SECTION 2 - COMPOSITION / INFORMATION ON HAZARDOUS INGREDIENTS Ingredient: CAS #: Occupational Exposure Limit: 1) Bisphenol A OSHA PEL: Limit has not been established Epichlorohydrin ACGIH TLV: Limit has not been established SECTION 3 - PHYSICAL /CHEMICAL PROPERTIES 3.1 Appearance and Odor Physical state: Very viscous liquid Color: Very light Yellow Odor: 3.2 Physical Data Boiling Point: > 500 F Melting Point: N/A Vapor Pressure: 0.03 MM 77 C Vapor Density: N/A Evaporation Rate: N/A Solubility in Water: Negligible Specific Gravity: 1.17 SECTION 4 - FIRE AND EXPLOSION DATA Flash Point: 480 F Flammable Limits: % Volume in air Lower N/AV/ Upper N/AV Extinguishable Media: Use water fog, foam, dry chemical or CO2 Special Fire Fighting Procedures: Heating above 300 F in the presence of air, may cause oxidative decomposition and / or polymerization. Unusual Fire and Explosion Hazards: Fumes and vapors may be toxic. Do not breath fumes. Use NIOSH approved respirator. SECTION 5 STABILITY AND REACTIVITY DATA Stability: Stable Incompatibility (Materials to avoid): Strong oxidizing agents Hazardous Decomposition or Byproducts: Thermal decomposition may cause CO Hazardous Polymerization: Aldehydes and acids

2 Page 2 of 6 SECTION 6 - HEALTH HAZARD DATA 6.1 Primary Routes of Entry: Eyes: Yes Skin: Moderately irritating Inhalation: Not relevant due to low volatility Ingestion: Low order of acute toxicity. 6.2 Health Hazards Acute: Moderately irritating to the eyes and skin. Chronic: N/A Carcinogenicity: N/A NTP: No Monographics: No Signs and Symptoms of Exposure: Shortness of breath. Excessive inhalation may cause headache, nausea and dizziness. Medical Conditions Aggravated by Exposure: None Known 6.3 Emergency and First Aid Procedure: Flush eyes with water. Wash exposed skin areas with water. Remove person to fresh air. Provide with oxygen if breathing is difficult. If accidentally ingested consult physician. SECTION 7 - PRECAUTIONS FOR SAFE HANDLING AND USE 7.1 Handling and Storage: Protect from moisture 7.2 Other Precautions: Do not breathe dust and avoid contact with skin and eyes 7.3 Released or Spilled: Soak up with absorbent clay or sand 7.4 Waste Disposal Method: Dispose as common waste according to local, state and Federal Regulations SECTION 8 CONTROL MEASURES Respiratory Protection: None required if well ventilated Ventilation: Yes Local Exhaust: Yes Mechanical: N/A Special: N/A Protective Gloves: Rubber gloves recommended Eye Protection: Tight fitting safety goggles Other Protective Clothing: Avoid contact with skin, eyes and clothing. Wash hand thoroughly after handling. Work Hygienic Practices: Good housekeeping practice is recommended. Date: Disclaimer: The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy. Since the use of this information and the conditions of use of the product are not within the control of Southern Grouts and Mortars, Inc., it is the users obligation and responsibility to determine the condition of safe use of the product. SGM Inc., assumes no responsibility for personal injury or property damage.

3 Page 3 of 6 Material Safety Data Sheet SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION: 1.1 Product Name: EGS Mortar & Grout System (Part B) 100% Epoxy 1.2 Company Identification: Southern Grouts and Mortars, Inc SW 2nd Place Pompano Beach, Florida (954) SECTION 2 - COMPOSITION / INFORMATION ON HAZARDOUS INGREDIENTS Ingredient: CAS #: 1) Tetraethylenepentamine 90% Talloil Fatty Acid Amino Amine 2) Tetraethylenepentamine 10% Acute Oral LD gr/kg (Rat) Acute Dermal LD gr/kg (Rabbit) Acute Inhalation LD mg/m3 (Mouse) 3) Triethylenetetramine 3% Acute Oral LD gr/kg (Rat) Acute Dermal LD gr/kg (Rabbit) Acute Inhalation LD mg/m3 (Mouse) SECTION 3 - PHYSICAL / CHEMICAL PROPERTIES 3.1 Appearance and Odor Physical state: Liquid Color: Clear - Amber Odor: Amine odor 3.2 Physical Data Boiling Point: > 340 F Melting Point: N/A Vapor Pressure: 20 C Vapor Density: N/A Evaporation Rate: N/A Solubility in Water: Partial Specific Gravity: 0.94 SECTION 4 - FIRE AND EXPLOSION DATA Flash Point: >200 F Setaflash Flammable Limits: % Volume in air Lower 1.4 / Upper N/A Extinguishable Media: Use water fog, foam, dry chemical or CO2 Special Fire Fighting Procedures: N/A Unusual Fire and Explosion Hazards: N/A SECTION 5 STABILITY AND REACTIVITY DATA Stability: Stable Incompatibility (Materials to avoid): Mineral Acids Hazardous Decomposition or Byproducts: Thermal decomposition may cause CO Hazardous Polymerization: Will not occur

4 Page 4 of 6 SECTION 6 - HEALTH HAZARD DATA 6.1 Primary Routes of Entry: Eyes: Yes Skin: Yes Inhalation: Yes Ingestion: Yes 6.2 Health Hazards Acute: Can dry the skin, irritate eyes and upper respiratory system. Chronic: Inhalation can cause inflammation of interior of nose, throat respiratory tract, headache and nausea Carcinogenicity: N/A NTP: No Monographics: No Signs and Symptoms of Exposure: Shortness of breath. Excessive inhalation may cause headache, nausea and dizziness. Medical Conditions Aggravated by Exposure: None Known 6.3 Emergency and First Aid Procedure: Flush eyes with water. Wash exposed skin areas with water. Remove person to fresh air. Provide with oxygen if breathing is difficult. If accidentally ingested consult physician. SECTION 7 - PRECAUTIONS FOR SAFE HANDLING AND USE 7.1 Handling and Storage: Protect from moisture 7.2 Other Precautions: To the best of our knowledge, the information contained in this MSDS is accurate. It must be noted, however, that due to the fact that the conditions of handling and use are out of our control, we cannot guarantee the results nor can we assume any liability for damages incurred by the use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations. 7.3 Released or Spilled: Soak up with compatible absorbent material (sand, clay litter, diatomaceous earth) 7.4 Waste Disposal Method: Dispose as common waste according to local, state and Federal Regulations SECTION 8 CONTROL MEASURES Respiratory Protection: None required if well ventilated Ventilation: Yes Local Exhaust: Yes Mechanical: N/A Special: N/A Protective Gloves: Rubber gloves recommended Eye Protection: Tight fitting safety goggles Other Protective Clothing: Avoid contact with skin, eyes and clothing. Wash hand thoroughly after handling. Work Hygienic Practices: Good housekeeping practice is recommended. Date: Disclaimer: The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy. Since the use of this information and the conditions of use of the product are not within the control of Southern Grouts and Mortars, Inc., it is the users obligation and responsibility to determine the condition of safe use of the product. SGM Inc., assumes no responsibility for personal injury or property damage.

5 Page 5 of 6 Material Safety Data Sheet SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION: 1.1 Product Name: EGS Mortar & Grout System (Part C) 100% Epoxy 1.2 Company Identification: Southern Grouts and Mortars, Inc SW 2nd Place Pompano Beach, Florida (954) SECTION 2 - COMPOSITION / INFORMATION ON HAZARDOUS INGREDIENTS Ingredient: CAS #: Occupational Exposure Limit: 1) Silica Sand OSHA PEL: 0.1 mg/m3 (Respirable dust) 0.3 mg/m3 (Total dust) ACGIH TLV: 0.1 mg/m3 1) Nuisance Dust OSHA PEL: 5 mg/m3 (Respirable dust) 15 mg/m3 (Total dust) ACGIH TLV: 10 mg/m3 SECTION 3 - PHYSICAL / CHEMICAL PROPERTIES 3.1 Appearance and Odor Physical state: Coarse textured powder Color: Gray / White or colored Odor: No odor 3.2 Physical Data Boiling Point: N/A Melting Point: N/A Vapor Pressure: N/A Vapor Density: N/A Evaporation Rate: N/A Solubility in Water: Miscible Specific Gravity: 2.5 SECTION 4 - FIRE AND EXPLOSION DATA Flash Point: N/A Flammable Limits: N/A Extinguishable Media: N/A Special Fire Fighting Procedures: Material will not burn unless preheated. Do not enter confined fire space without full bunker gear, including positive pressure self-contained breathing apparatus. Unusual Fire and Explosion Hazards: Delayed lung damage can be experienced with hours after exposure to combustion products. Nitrogen containing organic compounds may be released upon combustion. * Note: Colors may contain one or more of the following pigments: Yellow Iron Oxide (CAS ), Red Iron Oxide (CAS ), Black Iron Oxide (CAS ), Chromium Oxide (CAS ), Carbon Black (CAS ), Metal Oxide Silicate (CAS ), Titanium Dioxide (CAS ), Phthalocyanine Blue (CAS , CAS ), Calcium Carbonate (CAS ). SECTION 5 STABILITY AND REACTIVITY DATA Stability: Stable Incompatibility (Materials to avoid): Avoid heat flame and contact with strong oxidizing agents.

6 Page 6 of 6 Hazardous Decomposition or Byproducts: Nitrogen oxides, CO and unidentified organic products may form combustion. Hazardous Polymerization: Will not occur. SECTION 6 - HEALTH HAZARD DATA 6.1 Primary Routes of Entry: Eyes: Corrosive and may cause severe damage Skin: Corrosive and may cause sensitization. May be toxic if absorbed through the skin. May cause reproductive effects. Inhalation: Vapors / mists may be corrosive to upper respiratory tract. Repeated exposure can result in lung damage. May cause respiratory tract sensitization. Ingestion: Corrosive and may cause severe permanent damage to throat, and stomach. 6.2 Health Hazards Acute: Corrosive Chronic: N/A Carcinogenicity: N/A NTP: No Monographics: No Signs and Symptoms of Exposure: Skin and/or eye irritation, shortness of breath, wheezing and chronic cough. Medical Conditions Aggravated by Exposure: None Known 6.3 Emergency and First Aid Procedure: Flush eyes with water for fifteen minutes and get medical attention. Remove contaminated clothing. Wipe off from skin and wash exposed skin areas with water. Remove person to fresh air. Provide with oxygen if breathing is difficult. If accidentally ingested, do not induce vomiting. Get medical attention. SECTION 7 - PRECAUTIONS FOR SAFE HANDLING AND USE 7.2 Handling & Storage: To the best of our knowledge, the information contained in this MSDS is accurate. It must be noted, however, that due to the fact that the conditions of handling and use are out of our control, we cannot guarantee the results nor can we assume any liability for damages incurred by the use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations. 7.2 Released or Spilled: Soak up with compatible absorbent material (sand, clay litter, diatomaceous earth) 7.3 Waste Disposal Method: Dispose as common waste according to local, state and Federal Regulations SECTION 8 CONTROL MEASURES Respiratory Protection: Use NIOSH approved respirator N accord with 29 CFR Ventilation: Yes Local Exhaust: Yes Mechanical: N/A Special: N/A Protective Gloves: Rubber gloves recommended Eye Protection: Tight fitting safety goggles Other Protective Clothing: Use apron and overshoes. Work Hygienic Practices: Good housekeeping practice is recommended. Date: Disclaimer: The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy. Since the use of this information and the conditions of use of the product are not within the control of Southern Grouts and Mortars, Inc., it is the users obligation and responsibility to determine the condition of safe use of the product. SGM Inc., assumes no responsibility for personal injury or property damage.

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION PRODUCT: M-Bond 200 Catalyst C May 7, 2013 Vishay Measurements Group, Inc. Post Office Box 27777 Raleigh, NC 27611 919-365-3800