MATERIAL SAFETY DATA SHEET

Transcription

1 MATERIAL SAFETY DATA SHEET 1. PRODUCT AND PREPARATION INFORMATION Manufacturer: Bloomco/Division of Double B 5035 North Service Rd., Unit B4 Burlington, Ontario, L7L 5V2, Canada (905) Emergency telephone numbers: Bloomco 24 Hours: (800) Product Name: Synonyms: Not Applicable Chemical Family: Petroleum Hydrocarbons & Silicones Molecular Formula: Product Use: Coating WHIMIS Classification: B3 TDG Classification: Flammable liquid, n.o.s. (Petroleum distillates), Class 3, UN1993, PGIII. NFPA: 1 Health, 2 Fire, 0 Instability Prepared by: Research and Development Department Preparation Date: April 21, HAZARDOUS INGREDIENTS Hazardous Ingredients Polydimethyl Siloxane Distillates (petroleum), Hydrotreated Light CAS Number Wt. % TLV ppm LD/50 Oral Rat LC/50 Inhal Rat, 4 hr Not > 5,000 mg/kg Available > 5,000 mg/kg - 1 -

2 3. PHYSICAL DATA Physical State Appearance Odour Odour Threshold Boiling Point Melting/Freezing Point Liquid Clear Faint 170 deg. C Vapour Density (Air = 1) > 1 Specific Gravity (g/cc) 0.81 Vapour Pressure (mm Hg) Evaporation Rate, n-butyl Acetate = 1 PH Solubility in Water Not Applicable Insoluble 4. FIRE AND EXPLOSION DATA Flammability Limits in Air (%): 1-9 Extinguishing Media: Dry chemicals, CO2, alcohol foam or water spray. Not recommended: water jet. Use water spray to cool containers. Flash Point (TCC deg. C): 50. Autoignition Temperature (deg. C): 350. Hazardous Combustion Products: Carbon monoxide, silica oxide. Sensitivity to Mechanical Impact: Not available. Not expected to be sensitive to mechanical impact. Rate of Burning: Not available. Explosive Power: Not available. Sensitivity to Static Discharge:. Unusual Fire Hazard: Product will float and can be reignited on surface of water. Vapors are heavier than air and may accumulate in low areas. Contents - 2 -

3 may develop pressure on prolonged exposure to heat. 5. REACTIVITY DATA Chemical Stability: Compatibility with Other Substances: Hazardous Products of Decomposition: Hazardous Polymerisation:, under normal conditions. Avoid excessive heat, open flames and all ignition sources. Oxides or carbon, oxide of silica, smoke. Will not occur. 6. TOXICOLOGICAL PROPERTIES Route of Entry: Skin Contact: Skin Absorption: Eye Contact: Inhalation: Ingestion: Effects of Exposure: Carcinogenicity of material: Reproductive effects: Teratogenicity: Mutagenicity: Ingestion of large amounts is likely to cause CNS effects such as dizziness, nausea and vomiting. Aspiration into the lungs may occur during ingestion or vomiting, resulting in lung injury. Product is slightly irritating to the eyes, nose, throat and respiratory tract. May be absorbed through skin. Carcinogenic effects are anticipated. Reproductive effects are anticipated. Teratogenic effects are anticipated. Mutagenic effects are anticipated. 7. PREVENTIVE MEASURES - 3 -

4 Eye Protection: Skin Protection: Respiratory Protection: Engineering Controls: Leak/Spill Clean-Up Procedures: Storage Instructions: Safety glasses are required. Contact lenses should not be worn when working with this material. Gloves should be impervious under condition of use. Discard contaminated gloves. Do not breathe vapours. A NIOSH/MSHAapproved chemical cartridge respirator with organic vapour cartridges if exposure exceeds TLV value. Good general ventilation, eye wash stations. Absorb spills with absorbent material and place in non-leaking container for disposal. Do not use combustible material such as sawdust. Ventilate enclosed spaces. Collect product for disposal. Dispose of waste material at an approved hazardous waste treatment/disposal facility in accordance with applicable local, provincial and federal regulations. Do not dispose of waste with normal garbage, or to sewer systems. Notify applicable government authority if release is reportable or could adversely affect the environment. Store in clean, cool well ventilated area. Protect from direct sunlight. Protect from physical damage. 8. FIRST-AID MEASURES In case of eye contact, immediately flush eyes with running water for a minimum of 15 minutes. Hold eyelids open during flushing. Get medical attention. For skin, remove contaminated clothing wash affected areas thoroughly with soap and water. Get medical attention if irritation happens. If affected by inhalation of vapour or spray mist, move to fresh air. If symptoms persist, get medial attention. In case of ingestion do not attempt to give anything by mouth to unconscious person. IMMEDIATELY contact local Poison Control Centre. Do not induce vomiting. If vomiting occurs spontaneously, keep head below hips to prevent aspiration of liquid into the lungs. Administer artificial aspiration if breathing has stopped. 9. OTHER INFORMATION This product has been classified in accordance with the hazard criteria of the CPR and the MSDS contains all the information required by the CPR. This MSDS is valid for three years

5 The information contained herein is based on data considered accurate. No warranty is expressed or implied regarding the accuracy of this data or the results obtained from the use thereof. Bloomco assumes no responsibility for personal injury or property damage to vendees or users or third parties, caused by the material. Such vendees or users assume all risks with the use of the material. Signature of Preparer: R & D Department Phone Number: