Potable Water Truck Safe Work Procedure PTES_HSE_SWP_041. Name Date Signature. Author Geoff Selfe 25/01/2016. Reviewed Solomon Site 25/01/
|
|
- Augustine Clarke
- 5 years ago
- Views:
Transcription
1 Potable Water Truck Safe Work Procedure PTES_HSE_SWP_041 Name Date Signature Author Geoff Selfe 25/01/2016 Reviewed Solomon Site 25/01/ Approved Michael Garkaklis 25/01/2016
2 Key Safety Acts Complete a 5 Step prior to commencing any work Gloves shall be worn for all manual tasks Always use correct manual handling techniques Maintain good housekeeping at all times. Stow away unused gear. Be aware of your surroundings All operations of this equipment should be carried out on stable/ firm ground and the equipment should not be shock loaded. Access and egress must be performed using 3 points of contact at all times. Use horn warning signals: - Start One blast, Forward Two blasts, Reverse Three blasts. Check for power lines before setting up at a work site. Ensure area is clear of personnel and objects before moving your load. Qualifications Required to Operate HR Driver s License Site inductions and VOC s completed Attend morning pre-start meetings Ensure you have read Guidelines for the Bulk Cartage of Drinking Water issued by WA Department of Health (2004). PTES_HSE_SWP_041 Potable Water Truck Safe Work Procedure Rev 1 25/01/2016 Page 2 of 10
3 Shall - the instruction is compulsory. Should - the instruction is preferred but allows for initiative to be exercised. A JHA should be written for any variation in procedure or for the control of any new hazards that are identified. Correct manual handling technique: Utilise suitable Personnel appropriate for the task- consider age, special skills, capabilities and knowledge. Determine a lifting leader who will provide verbal instructions during the manual handling task. Definitions Ensure all Personnel involved are warm and stretched prior to undertaking any manual handling tasks. Ensure lifting point, path and set down points are free from obstacles and that the floor surfaces are not slippery. Remember to keep your spine in a neutral posture throughout the manual handling task. Consider the use of any manual handling aids, such as trolleys or hoists to minimize the weight lifted by Personnel. Avoid jerky movements, side bending or twisting during the manual handling process. Ensure the load is kept as close to the body as possible with the load sustained below your shoulders but above your mid-thigh. PTES_HSE_SWP_041 Potable Water Truck Safe Work Procedure Rev 1 25/01/2016 Page 3 of 10
4 PPE PPE requirements for this task are: high visibility reflective long sleeved shirt and long pants, safety glasses, gloves, safety boots and hard hat Take 5 Complete a Take 5 prior to commencing a prestart inspection, loading/ unloading operations or any other hazardous task. JHA Complete a JHA prior to commencing, if the scope of work has changed. Reference Documentation Government of Western Australia Dept of Health Public Health - Guidelines for the Bulk Cartage of Drinking Water. PTES_HSE_SWP_041 Potable Water Truck Safe Work Procedure Rev 1 25/01/2016 Page 4 of 10
5 Prestart Inspection Turn on battery isolator and chock wheels, lock on with your Personal Danger Tag. Check gauge for oil and air pressure. Check lights and indicators. Check for fluid and air leakage. Check wheel nuts and cleats. Check for tyres damage. Check for tank/fitting leakage and un-sanitary fittings/pipes. Complete Log book entries of water quality readings, pick-up facility and generic questions stated with each load carted. Unstable Ground Uncontrolled Plant Movement Operator Competence Where possible, operator to ensure plant is parked on relatively stable/level ground. Operator to ensure plant is turned off, isolated, two forms of braking are applied and wheel chocks in place. PTES Group Supervisor to ensure periodical VOC of operator. PTES_HSE_SWP_041 Potable Water Truck Safe Work Procedure Rev 1 25/01/2016 Page 5 of 10
6 Job Planning Operator to assess and plan task prior to commencement. Driving to site of operation Adhere to WA Road Rules, Site requirements & Regulations. Always drive to conditions. Be constantly aware of road conditions at all times. Utilise a spotter in areas with reduced visibility Positive radio contact SHOULD be initiated when overtaking other vehicles/machines. Ensure familiarity of location and operation of controls Vehicle Collision Operator Competence Operator to be vigilant at all times when parking. Operator to use a spotter if required. PTES Group Supervisor to ensure periodical VOC of operator. Vehicle / Personnel Interaction Ensure all personnel and other operators are aware of your intentions. Water Truck Operations Truck signage shall be labelled Drinking Water Only in lettering 100mm high. Backflow prevention device shall be fitted to the inlet and outlet. All pipes and fittings should be labelled Drinking Water Only or water marked in accordance with AS 4020 or ATS Where containers/tankers/fitments are continually used they should be regularly cleaned at least every 3 months by: Filling and keeping full for at least 30 minutes (circulating through the pump) with water containing at least 4.0mg per litre free chlorine rinsing with drinking water and sealed securely against dirt or dust. The above process should also be used where the container and fitments are used for the first time or following a period of storage. Operator Competence Vehicle Collision PTES Group Supervisor to ensure periodical VOC of operator. Operator to be vigilant at all times when parking. Operator to use a spotter if required. PTES_HSE_SWP_041 Potable Water Truck Safe Work Procedure Rev 1 25/01/2016 Page 6 of 10
7 During transport operations containers and fitments should be completely sealed to prevent the ingress of dust and contaminants When not in use containers and fitments should be sealed stored in such a manner as to prevent contamination. DO NOT USE DRINKING WATER CONTAINERS and FITMENTS FOR ANY OTHER PURPOSE. Water Truck Operations (Tank Filling) Ensure truck is chocked when parking up to commence operations and hand brake is applied. Water truck hose to be removed from tray/box utilising correct manual handling techniques. Hose is to be connected to water truck and water tank with cam lock fittings securely closed and seals intact. Ensure traffic cones are utilised around hose to highlight the hazard and restrict access to the area whilst tank filling operations are undertaken. Turn on PTO (where positive pressure isn t available) and open valve at truck first and valve at tank second. Monitor tank overflow (Fill Level) continuously during filling operations to ensure no overflow occurs. Close tank valve when fill level has been reached and disengage PTO. Drain excess potable water from hose after disconnection to ensure no unnecessary weight is lifted. Operator Competence Vehicle Collision PTES Group Supervisor to ensure periodical VOC of operator. Operator to be vigilant at all times when parking. Operator to use a spotter if required. PTES_HSE_SWP_041 Potable Water Truck Safe Work Procedure Rev 1 25/01/2016 Page 7 of 10
8 Remove hose from all connections, cap and place securely in designated storage box/tray. During Transportation; Empty all hose connections to containers, standpipes and supply points. Join end to end or cap hoses, standpipes or supply points to eliminate any chance of contamination by dirt, dust or foreign objects, cap and seal outlets on containers (tanks). Empty any other fitting that is used in the water system and store away from dirt, dust and other contaminates. Consumer Advice: Carriers should advise consumers to disinfect and maintain the drinking water prior to consumption by providing the Consumer Advisory Notice attached to page 9 of the Guidelines for the Bulk Cartage of Drinking Water. RECORD KEEPING: Carriers shall keep in delivery vehicles a logbook that records; details of the date, source, destination and volume of bulk drinking water delivered, chemical treatment test results for each load of drinking water delivered (free available chlorine); and the date of cleaning and inspection of tanks and fitments. A model log book is attached on page 10 of the Guidelines for the Bulk Cartage of Drinking Water. PTES_HSE_SWP_041 Potable Water Truck Safe Work Procedure Rev 1 25/01/2016 Page 8 of 10
9 Unstable Ground Where possible, operator to ensure plant is parked on relatively stable/level ground. Uncontrolled Plant Movement Operator to ensure plant is turned off, isolated, two forms of braking are applied and wheel chocks in place. Shutting Down Truck Reverse park truck in designated park bay or V drain Reduce speed and bring the water truck to a safe stopping position Engage the handbrake/park brake and leave the truck in neutral. Turn the engine key off. Note This will initiate the turbo timer (usually 3 minutes) to allow for the turbo to cool down If a turbo timer is not present then the truck should idle for 3 minutes before being shut down. Isolate truck. Ensure two forms of braking are applied. Manual handling Crush Vehicle / Personnel Interaction Operator to apply correct manual handling techniques at all times. Operator to ensure hands are not placed in the line of fire thereby eliminating the possibility of a crush injury. Ensure all personnel and other operators are aware of your intentions. Vehicle Collision Operator to be vigilant at all times when parking. Operator to use a spotter if required. PTES_HSE_SWP_041 Potable Water Truck Safe Work Procedure Rev 1 25/01/2016 Page 9 of 10
10 Sign on Sheet By signing on to this sheet I agree that I have read the required Safe Work Procedure in relation to the Potable Water Truck (Drinking Water Only) and understand all elements of the task that I will be performing. I agree to ensure I undertake a Take 5 prior to performing the task and will ensure I complete a prestart on the piece of equipment I will be operating. Date Operator Name Operator Signature Supervisor Name Supervisor Signature PTES_HSE_SWP_041 Potable Water Truck Safe Work Procedure Rev 1 25/01/2016 Page 10 of 10
Garbex Drum Crusher Safe Work Procedure PTES_HSE_SWP_028. Name Date Signature. Author Jarred Hearle 30/11/2014. Reviewed John Nulty 30/11/2014
Garbex Drum Crusher Safe Work Procedure PTES_HSE_SWP_028 Name Date Signature Author Jarred Hearle 30/11/2014 Reviewed John Nulty 30/11/2014 Approved Geoff Selfe 01/12/2014 Key Safety Acts Complete a 5
More informationProcessing Fire Extinguishers Safe Work Procedure PTES_HSE_SWP_038. Name Date Signature. Author Jarred Hearle 21/09/2015
Processing Fire Extinguishers Safe Work Procedure PTES_HSE_SWP_038 Name Date Signature Author Jarred Hearle 21/09/2015 Reviewed John Nulty 21/09/2015 Approved Geoff Selfe 21/09/2015 Key Safety Acts Complete
More informationOperation of Embrey Excavator Shears Safe Work Procedure PTES_HSE_SWP_039. Name Date Signature. Author Jarred Hearle 27/11/2015
Operation of Embrey Excavator Shears Safe Work Procedure PTES_HSE_SWP_039 Name Date Signature Author Jarred Hearle 27/11/2015 Reviewed FMG Site Team 27/11/2015 ---------- Approved Geoff Selfe 27/11/2015
More informationHigh Pressure Washer Safe Work Procedure PTES_HSE_SWP_006. Name Date Signature. Author John Nulty 12/05/2015. Reviewed Jarred Hearle 12/05/2015
High Pressure Washer Safe Work Procedure PTES_HSE_SWP_006 Name Date Signature Author John Nulty 12/05/2015 Reviewed Jarred Hearle 12/05/2015 Approved Geoff Selfe 12/05/2015 Key Safety Acts Complete a 5
More informationSAFE WORK METHOD STATEMENT Part B
SAFE WORK METHOD STATEMENT Part B SWMS No.: 01 WORK ACTIVITY DESCRIPTION: Door Installation All FORESEEABLE OHS & ENVIRONMENTAL HAZARDS & RISKS ASSOSSIATED WITH THE WORKS MUST BE ASSESSED & ALLOCATED CONTROLS
More informationJOB SAFETY ENVIRONMENT ANALYSIS (JSEA) Working With In Situ Testing Rigs
Personnel Involved Manager Project Operators Assistant Notes re Operator/Off-Sider Training Allan McConnell In situ testing is a niche business with very few rigs in Australia. There are no specific training
More informationHow severely could the risk hurt someone?
Safe Work Method Statement No: WMS-08 Task: Install Drainage This WMS is submitted to: Project name and site address: Contact: Preparation of WMS by: Robert Raams Company: Enwon (Australia) Pty Ltd Authorised
More informationWORK METHOD STATEMENT STRUCTURAL STEEL
ORGANISATION DETAILS Organisation Name: Gedoun Constructions Pty Ltd Contact Name: Joe Gedoun ACN/ABN: 52 284 873 581 Contact Position: Director Address: PO Box 1138, Townsville QLD 4810 Contact Phone
More informationContractor OHS Induction. AOHS-05-GUI September 2016
Contractor OHS Induction AOHS-05-GUI-002 8 September 2016 1 About AQWEST AQWEST is a Government Trading Enterprise responsible for supplying drinking water to Bunbury. Formed in 1906 as the Bunbury Water
More informationJOB SAFETY ANALYSIS. How to use the Risk Assessment Charts. Likelihood A (Almost Certain) B (Likely) C (Possible)
Page 1 of 6 How to use the Assessment Charts 1. Determine the Likelihood on the Qualitative Assessment Process Chart (pick a letter applicable to the task). 2. Determine the Consequence on the Qualitative
More informationSAFE WORK METHOD STATEMENT SWMS No Version
SAFE WORK METHOD STATEMENT SWMS No Version Company Name: Hunter Readymixed Concrete Pty Ltd 00 004 Location: Thornton Cessnock Tea Gardens Gateshead ABN: 6 076 08 695 SWMS Developed By: Duane Harrison
More informationRemoving Frozen Clips
Removing Frozen Clips Warning You cannot undertake this activity in the rail corridor unless you have completed a pre work brief and work site protection plan. Reference should also be made to the Protocol
More informationSafe Work Method Statement LRB TREE SERVICES 6 Behland St, Kearneys Spring QLD, 4350 ABN
JOB NO: PROJECT: DATE: 1/1/2018 SWMS NO: SWMS 001.1 PREPARED BY: LUKE BLINCO REVISED BY: ACTIVITY: TREE REMOVAL & PRUNING SIGNED BY: REVISION DATE: MINIMUM PERSONAL PROTECTIVE EQUIPMENT (PPE) REQUIREMENTS
More informationManual Handling Procedure
Manual Handling Procedure Table of Contents 1 Purpose... 3 2 Scope... 3 3 Definitions... 3 4 Responsibilities... 3 4.1 Managers And Supervisors... 3 4.2 Workers (Employees, Contractors And Visitors)...
More informationHow severely could the risk hurt someone? Low/Insignificant First aid
Safe Work Method Statement No: WMS-02 Task: Concreting, Formwork and Steel Fixing This WMS is submitted to: Project name and site address: Contact: Preparation of WMS by: Robert Raams Company: Enwon (Australia)
More informationU.S. CONCRETE, INC. SAFETY POLICY and PROCEDURE MANUAL
SAFE -14 Page 1 of 8 U.S. CONCRETE, INC. SAFETY POLICY and PROCEDURE MANUAL FUNCTION Safety TOPIC Hotwork Permit Program OBJECTIVE(S): GENERAL POLICY: To provide a work atmosphere that is conducive to
More informationFLYING OBJECTS MANUAL HANDLING EXCESSIVE NOISE
JOB NO: PROJECT: DATE: SWMS NO: SWMS 002 PREPARED BY: Ian Hartley REVISED BY: Nick Bragg & Cameron McNeil ACTIVITY: STUMP REMOVAL SUPERVISED BY: REVISION DATE: April 2016 MINIMUM PERSONAL PROTECTIVE EQUIPMENT
More informationMONTHLY SAFETY NEWSLETTER
CONTACT ELECTRIC SAFETY NEWSLETTER FOR ENSURE ALL EMPLOYEES AND SUB-CONTRACTORS WORKING FOR AVALANCHE ACID REVIEW THIS NEWSLETTER. IT IS A KEY PART OF OUR SAFETY PROGRAM DECEMBER 2017 VOL.12 MONTHLY SAFETY
More informationLEARNER GUIDE. Asphalt Paver (AP) PO Box 2026 Mountain Gate VIC 3156 p: ABN: RTO: 21396
LEARNER GUIDE Asphalt Paver (AP) PO Box 06 Mountain Gate VIC 3156 p: 03 9763 5449 ABN: 37 106 951 900 RTO: 1396 Asphalt Paver Safety Part One PERFORMANCE ASSESSMENT Unit 1 Conduct Routine Checks: 1. Routine
More informationWORK METHOD STATEMENT CARPET LAYING
ORGANISATION DETAILS Organisation Name: Gedoun Constructions Pty Ltd Contact Name: Joe Gedoun ACN/ABN: 52 284 873 581 Contact Position: Director Address: PO Box 1138, Townsville QLD 4810 Contact Phone
More informationWestern Sydney University Safety Inspection Checklist - Laboratory Environments
Western Sydney University Safety Inspection Checklist - Laboratory Environments Useful Hint: To maximise the benefits that can be gained from a workplace inspection activity read the Western Sydney University
More informationMeuangvang Development Co.LTD Standard Working Procedure 058 Use of Hydraulic Torqueing Devices
1. Application To provide a standard work procedure for as required in accordance with Meuangvang Development Co Ltd Safety Management Program 2. Revision Schedule Rev # Old Section Ref New Section Ref
More informationSAFE WORK METHOD STATEMENT
SAFE WORK METHOD STATEMENT WATER PUMP - PETROL Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES
More informationSafe Work Method Statement. Hook up and Towing - Risk Assessment
Hook up and Towing - Risk Assessment WORK STRUCTURES ABN: 97142401501 Work Activity/ Task: Hook up & Towing Caravan Address: 4 KAMHOLTZ CRT ASHMORE 4214 QLD Phone: 0404600001 Email: sales@caravans-australia.com.au
More informationSAFETY MANAGEMENT SYSTEM
Equipment Location: Hazard Hired From All Master Hire Stores Entanglement Can anyone s hair, clothing, gloves, necktie, jewellery, cleaning brushes, rags or other materials become entangled with moving
More informationSAFE WORK METHOD STATEMENT
SAFE WORK METHOD STATEMENT LOADING AND UNLOADING VEHICLES Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES
More informationLAKE ARROWHEAD COMMUNITY SERVICES DISTRICT STANDARD OPERATING PROCEDURES FACILITY SAFETY The following procedures are to be used by all District employees when working in the District facilities or with
More informationWork Activity (e.g. Road Work): Work Location:.
Working with Cranes Work Activity (e.g. Road Work): Work Location:. GENERAL INFORMATION Hinchinbrook Shire Council Lannercost Street Ingham Qld, 4850 ABN 46 291 971 168 Ph: 47764610 All personnel conducting
More informationSCOPE OF WORK, SAFETY METHOD STATEMENT & RISK ASSESSMENT
SCOPE OF WORK, SAFETY METHOD STATEMENT & RISK ASSESSMENT Prepared for:- Date:- Work Scheduled:- SCOPE OF WORK Carry out installation of flow meters / pressure sensors. Installation of flow meter procedure
More informationSafety, health and environment values that are expected of all persons who are working and visiting the Quattro Ports Port Kembla Grain Terminal,
Overview In accordance with the Quattro Ports Safety, Health and Environmental Policy - Safety First is paramount to Quattro Ports. Our employees and contractors are our most important asset and their
More informationAppendix 4C - Sample SWMS Trenching
Appendix 4C - Sample SWMS Trenching SAFE WORK METHOD STATEMENT SWMS Reference : Insert document number : Version A Date : Workplace / Project : Company Address: Work Activity / Job / Task or Process :
More informationSAFETY MANAGEMENT SYSTEM
Equipment Location: Hazard Hired From All Master Hire Stores Entanglement Can anyone s hair, clothing, gloves, necktie, jewellery, cleaning brushes, rags or other materials become entangled with moving
More informationSAFETY MANAGEMENT SYSTEM
Equipment Location: Hazard Hired From All Master Hire Stores Entanglement Can anyone s hair, clothing, gloves, necktie, jewellery, cleaning brushes, rags or other materials become entangled with moving
More informationCranes and Hoists. Elevating Work Platforms ASSESSMENT
Cranes and Hoists Elevating Work Platforms ASSESSMENT Part 1 Part 2 Performance Oral/Written June 1995 Contents Page Assessor guidelines general guidelines for Schedule B i Part one Performance Assessment
More informationSafe Work Method Statement
Company Name: Safe Work Method Statement Site Address: Other Details: Contractor: Activity/Trade: Electrician Date: TASKS List the tasks required to perform the activity in sequence carried out. Entry
More informationACCREDITED SAFETY TRAINING FOR EQUIPMENT OPERATORS
JOB HAZARD ANALYSIS ELEVATING WORK PLATFORM Note: This is just a guideline. A Assessment must be designed for each specific EWP and each specific work area and task. A JHA is a never ending document. There
More informationMethod Statement: Testing Dry Riser System
Method Statement: Testing Dry Riser System Page 1 of 6 Scope of work Test dry riser system in accordance with BS 5306. Definitions For the purposes of this document, the following definitions apply Rising
More informationEMPLOYEE SAFETY ORIENTATION - PHYSICAL PLANT, RESIDENCE
Name Department Initial Orientation Date Supervisor Review Instructions: Check off each section once you have read and discussed it with your Supervisor. EMPLOYEE SAFETY ORIENTATION - PHYSICAL PLANT, RESIDENCE
More informationB S Glass Ltd Safety procedures- outsourced Workplaces
B S Glass Ltd Jan 17 B S Glass Ltd Safety procedures- outsourced Workplaces Index - - - - - - - - Page No On Site safety - - - - - - - - - - - - - - - - - - - Content 3. 1.00 Health and Safety Mission
More informationTentec. Instruction Document. Mini Air Driven Pump Unit Model: HTT.627X Series. Part Identifier
Tentec Page 1 w w w. t e n t e c. n e t Instruction Document Mini Air Driven Pump Unit Model: HTT.627X Series HTT.6271 Maximum Working Pressure = 1500bar (21750 psi) HTT.6272 Maximum Working Pressure =
More informationHazard Identification and Risk Assessment Form. Risk Assessment
Identification and Assessment Form Assessment Tool & Machine Work General Various injuries (including potential fatalities) All staff complete safety induction programme at the start of the module. instructed
More informationHazard Identification and Risk Assessment Form. Risk Assessment
Identification and Assessment Form Assessment Tool & Machine Work General Various injuries (including potential fatalities) All staff complete safety induction programme at the start of the module. instructed
More informationBitumen Delivery Driver Inductions Eurobitume UK
Bitumen Delivery Driver Inductions Eurobitume UK The information in this module is given in good faith and belief in its accuracy at the time of publication, but does not imply any legal liability or responsibility
More informationWORK METHOD STATEMENT TERMITE PROTECTION
ORGANISATION DETAILS Organisation Name: Gedoun Constructions Pty Ltd Contact Name: Joe Gedoun ACN/ABN: 52 284 873 581 Contact Position: Director Address: PO Box 1138, Townsville QLD 4810 Contact Phone
More informationThe Sample Company Pty Ltd
Job Safety and Environmental Analysis (JSEA) / Safe Work Method Statement (SWMS) Part 1: Project and Task Identification Process Initiators of SWMSs are responsible for consulting the Project Supervisor,
More informationJob Safety and Environmental Analysis (JSEA)/Safe Work Method Statement (SWMS)
Job Safety and Environmental Analysis (JSEA)/Safe Work Method Statement (SWMS) Part 1: Project and Task Identification Process: Initiators of JSEAs are responsible for consulting the Project Supervisor,
More informationStandard Operating Procedure
Procedure Type: Creation Date: Revision Date: Standard 12/22/2014 02/19/2016 Purpose: Ensure that the removal of an anthill around a wellhead is performed in a safe and controlled manner. Scope: This SOP
More informationTLILIC2005A Licence to operate a boomtype elevating work platform (boom length 11 meters or more)
TLILIC2005A Licence to operate a boomtype elevating work platform (boom length 11 meters or more) Release: 1 TLILIC2005A Licence to operate a boom-type elevating work platform (boom length 11 meters or
More informationHow severely could the risk hurt someone? Low/Insignificant First aid
Safe Work Method Statement No: WMS-0 Task: Line Marking This WMS is submitted to: Project name and site address: Contact: Preparation of WMS by: Robert Raams Company: Enwon (Australia) Pty Ltd Authorised
More informationSAFE WORK METHOD STATEMENT
SAFE WORK METHOD STATEMENT AUGER / POST HOLE DIGGER Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES
More informationApparatus Driver/Operator Evaluation Form Rosenbauer Tanker:
Section I: Apparatus Knowledge The Evaluator shall ask the Apparatus Driver/Operator questions regarding the mechanical systems and size of the apparatus. 1. The Apparatus Driver/Operator demonstrates
More informationRISK RATING SAFE WORK METHOD STATEMENT 1 HIGH 2 MEDIUM 3LOW. I approve the use of this Safe Work Method Statement: NAME: POSITION: Department Manager
RISK RATING 1 HIGH 2 MEDIUM 3LOW SAFE WORK METHOD STATEMENT Title: : Visual Bridge Inspection Ref No: 1 I approve the use of this Safe Work Method Statement: NAME: POSITION: Department Manager SIGNATURE:
More informationSafe Work Method Statement
Title Skid Steer Operation (Bobcat) SWMS No. 14 Authorized and email Signed by the (Managing Director / CEO / Partner / Proprietor) on Date 01/08 /2016 Safe Work Procedure for the Work:- Yes No Employees
More informationSAFETY MANAGEMENT SYSTEM
Equipment Location: Hazard Hired From All Master Hire Stores Entanglement Can anyone s hair, clothing, gloves, necktie, jewellery, cleaning brushes, rags or other materials become entangled with moving
More informationUniversity College Dublin Machinery/Equipment Risk Assessment Template
1. General Information Name of Person(s) carrying out assessment and their position Principal Investigator / Supervisor / Head of School or Unit (Person responsible for ensuring safety) Date of assessment
More informationThe Evaluator shall ask the Apparatus Driver/Operator questions regarding the mechanical systems and size of the apparatus.
Section I: Apparatus Knowledge The Evaluator shall ask the Apparatus Driver/Operator questions regarding the mechanical systems and size of the apparatus. 1. The Apparatus Driver/Operator demonstrates
More informationFIRE HYDRANT TESTING METHOD STATEMENT.
SUBJECT: TASK: FIRE HYDRANT INSPECTION & TESTING. 1. Location....1 2. The Scope of Works.... 1 3. Description of Task.... 1 4. Access & Egress to & from Work Area.... 2 5. Safety Hazard Identification....
More informationControl of Energy - Isolation Process
Issue Date: 24/03/17 Last Reviewed: 24/03/17 Next Review Date: 24/03/18 Authorised By: Mike Muir Safe Operating Procedure Control of Energy - Isolation Process Purpose: This SOP is based on a Generic 12-step
More informationSafe Work Method Statement
TE CONTROLLED COPY OF TIS DOCUMENT IS ON TE COMPUTER NETWORK PRINTED COPIES ARE ONLY CURRENT FOR TE DATE AT TE BOTTOM OF TE PAGE. Title Dogging of Crane General Loading and Unloading SWMS No. 20 Authorized
More informationHigh visibility jacket/tabard to be worn by all staff working on site and on the yard.
VEHICLES Vehicle movement Reversing vehicle Falls from vehicle Slips and trips Driver fatigue Securing loads on lorry Posh Wash employees and others may suffer serious, possible fatal injury if struck
More informationSafe Work Method Statement
TE CONTROLLED COPY OF TIS DOCUMENT IS ON TE COMPUTER NETWORK PRINTED COPIES ARE ONLY CURRENT FOR TE DATE AT TE BOTTOM OF TE PAGE. Title Working at eight SWMS No. 16 Authorized and email Signed by the (Managing
More informationConfined Spaces. This procedure applies to all workers of the Diocese of Maitland Newcastle (DoMN).
Purpose To provide guidance in controlling the risks associated with confined spaces including identifying confined spaces, working in a confined space and issuing confined space entry permits. Scope This
More informationSWMS documented by: Feb Bo Ceprnja Date Feb Feb Feb 2018
Contractor Company Details: BUILDSAFE SAFE WORK METHOD STATEMENT 0002 (Void Platform Stairs) Part 1 (To be used in conjunction with SWMS 0001 General Site Activities & SWMS 0002 Void Platform) Additional
More information1.0 PURPOSE 2.0 SCOPE 3.0 DEFINITIONS. ANSI: American National Standards Institute. CCC: Chemical Control Centre
Revision Date: 5/17/2016 Page: 1 of 13 Health & Safety has developed the emergency eyewash & safety shower equipment procedure which will be implemented in 3 phases over the next four years. Phase 1 will
More informationSafe Work Method Statement (SWMS) Worksheet
WORKPLACE / PROJECT NAME: AMS REF NO / TITLE: COMPANY NAME: NETWORK DIRECTIONAL DRILLING (GEELONG) P/L (if applicable) SWMS NO: (if applicable) WORK ACTIVITY / JOB / TASK OR PROCESS DESCRIPTION DATE SWMS
More informationSTANDARD OPERATING PROCEDURE
TO BE USED BY PROPERLY TRAINED AND AUTHORIZED PERSONNEL ONLY This document serves as a guide for the probable hazards of this space and how to remediate those hazards. It is important to remember that
More informationSAFE WORK METHOD STATEMENT
SAFE WORK METHOD STATEMENT EXCAVATION OR TRENCHING Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES
More informationThis written Compressed Gas Plan is kept at the corporate office and in the written Safety & Health Program.
Safety & Health Program 10627 Midwest Industrial Boulevard, St. Louis, MO Phone: 314-785-6425 Fax: 314-785-6426 Compressed Gas Plan Purpose It is the policy of EMA to permit only trained and authorized
More informationContractor Hazard Identification and Control Guide
Exposure to Asbestos Containing Materials (ACM) Accidental disturbance or removal of ACM. Asbestos Containing Materials are to be removed outside school hours. No DET employees, students or visitors are
More informationHYDROGEN PEROXIDE Railcar Unloading by Self-Priming Pump Technical Data Sheet
HYDROGEN PEROXIDE RAILCAR UNLOADING BY SELF-PRIMING PUMP INTRODUCTION All equipment used for storage and handling of hydrogen peroxide must be dedicated exclusively to hydrogen peroxide service and must
More informationBogo Operations Pollution Incident Response Management Plan
Bogo Operations Pollution Incident Response Management Plan Rhyolite Hard Rock Aggregate Quarry 134 Paynes Road BOOKHAM NSW 2582 PO Box 426 COWRA NSW 2794 p: 02 6227 7260 p: 02 6345 4253 e: info@bogoquarry.com.au
More informationSafe Work Instructions For Oxygen Acetylene Equipment
Safe Work Instructions For Oxygen Acetylene Equipment Policy Sponsor: Assistant Vice President Facilities Management Responsible Unit: Trade Services Approval Date: September 2010 Revisions: January 2018
More informationIPSWICH. Port Safety Notice
IPSWICH Port Safety Notice 19th October 2018 1 Associated British Ports Ipswich Port Safety Notice to Masters Introduction: This Port Safety Notice has been developed and communicated to provide general
More informationFlexfence Swaging Unit. Product Manual. Release 02/16.
Product Manual www.ingalcivil.com.au 1.0 Safety Precautions 1.1 Personal Protection While operating this equipment it is recommended that the following personal protective equipment be worn; Long sleeve
More informationLIQUID OXYGEN. General. Health Effects. Safety Considerations
LIQUID OXYGEN General Oxygen is the second largest component of the atmosphere, comprising 20.8% by volume. Liquid oxygen is pale blue and extremely cold. Although nonflammable, oxygen is a strong oxidizer.
More informationPotential hazards People at risk and how? Actions already in place Further action required Action by
Risk Assessment Flat Roof Repair Prepared by Oracle Managed Services For: BAM FM On: 24/02/2017 Review date: N/A Potential hazards People at risk and how? Actions already in place Further action required
More informationLeader s Guide ERI Safety Videos
1609 WORKING SAFELY WITH COMPRESSED GASCYLINDERS Leader s Guide ERI Safety Videos WORKING SAFELY WITH COMPRESSED GAS CYLINDERS PROGRAM SYNOPSIS: Safety must be a worker s number one priority when handling,
More informationSAFE WORK METHOD STATEMENT CARPENTER
HOST EMPLOYER DECLARATION I declare the worker/s named on this work authority have been provided with a site specific safety induction that complies with the requirements of the Workplace Health & Safety
More informationSTABLESAFE TRAINERS AUDIT TOOL
STABLESAFE TRAINERS AUDIT TOOL Name Address Date Postcode To assist stables in managing OH&S requirements trainers are encouraged to complete this stable audit tool. This audit is designed to help identify
More informationThe Sample Company Pty Ltd
Job Safety and Environmental Analysis (JSEA) / Part 1: Project and Task Identification Process Initiators of SWMSs are responsible for consulting the Project Supervisor, Quality WHS Manager or other persons
More informationPLANT RISK ASSESSMENT WORKSHEET (PRA)
Matrix Assessment Number: 00001 Assessment Date: 01 Jul 2015 Type: HA25 Dump Truck Make: KOMATSU Model: Highline Articulated Asset/Fleet/Rego No: 11-101 Serial No. 710872 Assessment Facilitated by: Tahir
More informationAIR-OPERATED DOUBLE DIAPHRAGM PUMP USER S MANUAL
00, 0, 000 00, 000, 00 A. TECHNICAL INFORMATION Model 00 Inlet/Outlet " Air Inlet /" 0 / 000 /" /" 00 /" /" 000 /" /" 00 /" /" Flow Rate GPM/ 0LPM GPM/ 0LPM GPM/ LPM GPM/ LPM GPM/ 0LPM GPM/ 0LPM Maximum
More informationSAFE WORK METHOD STATEMENT WORKING IN CONFINED SPACE HSE NET NAT SWMS APAND00030
SAFE WORK METHOD STATEMENT WORKING IN CONFINED SPACE HSE NET NAT SWMS APAND00030 HIGH RISK APT AM Holdings Pty. Ltd. [ABN] 95124754383 Principal Contractor (PC) APA Group Level 19, HSBC Building 580 George
More informationSH&E Work Method Statement Concrete Cutting & Drilling Fast Cut Qld Pty Ltd, 91 Basalt, GEEBUNG PH M ABN
SH&E Work Method Statement Concrete Cutting & Drilling Fast Cut Qld Pty Ltd, 91 Basalt, GEEBUNG PH 07 3265 6537 M 0411 756 719 ABN 45 081 359 613 OHS-FRM-100 Rev 11 (07/18) Page 1 SH&EWMS No.: F-C-QLD-30
More informationSafe Work Practices / Procedures / Instruction CONFINED SPACE
CONFINED SPACE Entry into and work in a confined space poses health and safety problems which may include: Presence or possible build up of a hazardous atmosphere Unexpected movement of equipment or materials
More informationJob Hazard Analysis. JHA No. FBP-JHA Revision No. Draft General or Job-Specific Description of Work
JHA No. FBP-JHA-14-0014 Revision No. Draft General or Job-Specific Description of Work Clean X230 Outlet Basin Site Location PORTS Activity or Area Name Not listed Facility or Project [Unspecified] Specific
More informationANNEX AMENDMENTS TO THE INTERNATIONAL CODE FOR FIRE SAFETY SYSTEMS (FSS CODE) CHAPTER 15 INERT GAS SYSTEMS
Annex 3, page 2 ANNEX AMENDMENTS TO THE INTERNATIONAL CODE FOR FIRE SAFETY SYSTEMS (FSS CODE) CHAPTER 15 INERT GAS SYSTEMS The text of existing chapter 15 is replaced by the following: "1 Application This
More informationOccupational Health Safety and Welfare. Our Policy
Occupational Health Safety and Welfare Our Policy OCUPATIONAL HEALTH AND SAFETY POLICY Management of QI Electrical Services is committed to ensuring, as far as responsibly practicable, that all employees
More informationMODULE 2 BRAZING CYLINDER TRANSPORT, STORAGE AND EQUIPMENT
MODULE 2 BRAZING CYLINDER TRANSPORT, STORAGE AND EQUIPMENT ISSUED BY REVISION NUMBER REVISION DATE DOCUMENT NUMBER S. GINBEY 0 7 th Nov 2016 QP74 Module 2 Cylinder Transport, Storage & Equipment ADR Regulations
More informationMeuangvang Development Co.LTD Standard Working Procedure 011 Towing Equipment
1. Application To provide a standard work practice for, as required in accordance with Meuangvang Development Co Ltd Safety Management Program 2. Revision Schedule Rev # Old Section Ref New Section Ref
More informationPLANT RISK ASSESSMENT
PLANT RISK ASSESSMENT Forktruck: Year of Manufacture Make: Model: Serial : TCM FD30T3 Attachment: Name: Mfg: Model : Owner: Business/Organisation: Address: This header page and the following 5 pages have
More informationTech Tips. Service Call: Adjustable Hydraulic Valves Flow controls Pressure controls Sequence valves Holding valves
Service Call: Adjustable Hydraulic Valves Flow controls Pressure controls Sequence valves Holding valves Tools Required: Flow Meter Pressure gauge Holding valve test block Wrenches for installation of
More informationWORK METHOD STATEMENT ALUMINIUM WINDOWS AND DOORS
ORGANISATION DETAILS Organisation Name: Gedoun Constructions Pty Ltd Contact Name: Joe Gedoun ACN/ABN: 52 284 873 581 Contact Position: Director Address: PO Box 1138, Townsville QLD 4810 Contact Phone
More informationNZQA registered unit standard version 3 Page 1 of 8. Operate bitumen gangbar sprayer transfer, heating, and blending equipment
Page 1 of 8 Title Operate bitumen gangbar sprayer transfer, heating, and blending equipment Level 4 Credits 15 Purpose People credited with this unit standard are able to: identify, assess, control, and
More informationSWMS No 012 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 6
Samark North Qld Pty Ltd SWMS SWMS No 0 Samark North Qld Pty Ltd ABN : 99 08 98 87 Electrical Contractors License C37 Page of 6 Safe Work Method Statement Title: SWMS:0 INSTALLING LIGHT POLES Work Method
More informationSEMPEO SQA Unit Code H2CB 04 Preparing and Manoeuvring Armoured Fighting Vehicles (AFVs) for Maintenance and Transportation
Preparing and Manoeuvring Armoured Fighting Vehicles (AFVs) for Maintenance and Transportation Overview This NOS identifies the competencies you need to carry out preparation and manoeuvring activities
More information20 Ton SD Shop Press Operating Instructions
20 Ton SD Shop Press Operating Instructions MODEL NO. 850SD Hazard Symbols Used in the Manuals This manual includes the hazard symbols defined below when the operations or maintenance job involves a potential
More informationPowerplay Paintball Brighouse Risk Assessment
Chemical Gas bottles Vehicles Physical Electricity Environment Machinery Powerplay Paintball Brighouse Risk Assessment Location Powerplay Paintball Wakefield and Brighouse Venues Carried out by: Steven
More informationLEARNER GUIDE. Trencher TS. PO Box 2026 Mountain Gate VIC 3156 p: ABN: RTO: 21396
LEARNER GUIDE Trencher TS PO Box 2026 Mountain Gate VIC 3156 p: 03 9763 5449 ABN: 37 106 951 900 RTO: 21396 National Guidelines for OHS Competency Standards Trencher Safety PERFORMANCE ASSESSMENT Assessor
More informationStaffing Services Client Evaluation Form
Staffing Services Client Evaluation Form Client Name: Location: Contact(s): Completed By: A Safety Performance Experience Modification Factor? OSHA 300 Logs Available? # Of Injuries/Illnesses? Types of
More information