AVM7 Stainless Steel Thermostatic Air Vent
|
|
- Oswin Miller
- 5 years ago
- Views:
Transcription
1 /4 IM-P ST Issue 4 AVM7 Stainless Steel Thermostatic Air Vent Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning 5. Operation 6. Maintenance 7. Spare parts Printed IM-P in the UK ST Issue 4 Copyright 20091
2 1. Safety information Safe operation of this product can only be guaranteed if it is properly installed, commissioned, used and maintained by qualified personnel (see Section 1.11) i n c o m p l i a n c e w i t h t h e o p e r a t i n g i n s t r u c t i o n s. G e n e r a l i n s t a l l a t i o n and safety instructions for pipeline and plant construction, as well as the proper use of tools and safety equipment must also be complied with. 1.1 Intended use Referring to the Installation and Maintenance Instructions, name-plate and Technical Information Sheet, check that the product is suitable for the intended use/application. The product listed below complies with the requirements of the European Pressure Equipment Directive 97/23/EC and carries the mark when so required. The product falls within the following Pressure Equipment Directive categories: Product Group 2 Group 2 Gases Liquids AVM7 SEP SEP i) The product has been specifically designed for use on steam, air or water/ condensate which are in Group 2 of the above mentioned Pressure Equipment Directive. The products use on other fluids may be possible but, if this is contemplated, Spirax Sarco should be contacted to confirm the suitability of the product for the application being considered. ii) Check material suitability, pressure and temperature and their maximum and minimum values. If the maximum operating limits of the product are lower than those of the system in which it is being fitted, or if malfunction of the product could result in a dangerous overpressure or overtemperature occurrence, ensure a safety device is included in the system to prevent such over-limit situations. iii) Determine the correct installation situation and direction of fluid flow. iv) Spirax Sarco products are not intended to withstand external stresses that may be induced by any system to which they are fitted. It is the responsibility of the installer to consider these stresses and take adequate precautions to minimise them. v) Remove protective covers from all connections and the protective film from all name-plates, where appropriate, before installation on steam or other high temperature applications. 1.2 Access Ensure safe access and if necessary a safe working platform (suitably guarded) before attempting to work on the product. Arrange suitable lifting gear if required. 1.3 Lighting Ensure adequate lighting, particularly where detailed or intricate work is required. 1.4 Hazardous liquids or gases in the pipeline Consider what is in the pipeline or what may have been in the pipeline at some previous time. Consider: flammable materials, substances hazardous to health, extremes of temperature. 2 IM-P ST Issue 4
3 1.5 Hazardous environment around the product Consider: explosion risk areas, lack of oxygen (e.g. tanks, pits), dangerous gases, extremes of temperature, hot surfaces, fire hazard (e.g. during welding), excessive noise, moving machinery. 1.6 The system Consider the effect on the complete system of the work proposed. Will any proposed action (e.g. closing isolation valves, electrical isolation) put any other part of the system or any personnel at risk? Dangers might include isolation of vents or protective devices or the rendering ineffective of controls or alarms. Ensure isolation valves are turned on and off in a gradual way to avoid system shocks. 1.7 Pressure systems Ensure that any pressure is isolated and safely vented to atmospheric pressure. Consider double isolation (double block and bleed) and the locking or labelling of closed valves. Do not assume that the system has depressurised even when the pressure gauge indicates zero. 1.8 Temperature Allow time for temperature to normalise after isolation to avoid danger of burns. If parts made from FKM have been subjected to a temperature above 250 C (482 F), it may have decomposed and formed flourine compounds, fluro hydrocarbons and fluro olefins. When subjected to temperatures above 500 C (932 F) parts made from FKM may ignite. Combustion residues are very corrosive and acidic, so acid-resistant gloves should be worn when handling, and calcium oxide/hydroxide can be used to neutralise it. 1.9 Tools and consumables Before starting work ensure that you have suitable tools and/or consumables available. Use only genuine Spirax Sarco replacement parts Protective clothing Consider whether you and/or others in the vicinity require any protective clothing to protect against the hazards of, for example, chemicals, high/low temperature, radiation, noise, falling objects, and dangers to eyes and face Permits to work All work must be carried out or be supervised by a suitably competent person. Installation and operating personnel should be trained in the correct use of the product according to the Installation and Maintenance Instructions. Where a formal 'permit to work' system is in force it must be complied with. Where there is no such system, it is recommended that a responsible person should know what work is going on and, where necessary, arrange to have an assistant whose primary responsibility is safety. Post 'warning notices' if necessary. IM-P ST Issue 4 3
4 1.12 Handling Manual handling of large and/or heavy products may present a risk of injury. Lifting, pushing, pulling, carrying or supporting a load by bodily force can cause injury particularly to the back. You are advised to assess the risks taking into account the task, the individual, the load and the working environment and use the appropriate handling method depending on the circumstances of the work being done Residual hazards In normal use the external surface of the product may be very hot. If used at the maximum permitted operating conditions the surface temperature of some products may reach temperatures in excess of 300 C (572 F). Many products are not self-draining. Take due care when dismantling or removing the product from an installation (refer to 'Maintenance instructions') Freezing Provision must be made to protect products which are not self-draining against frost damage in environments where they may be exposed to temperatures below freezing point Disposal Unless otherwise stated in the Installation and Maintenance Instructions, this product is recyclable and no ecological hazard is anticipated with its disposal providing due care is taken, except: FKM: - Can be landfilled, when in compliance with National and Local regulations (waste code no rubber waste; Germany). - Can be incinerated when in compliance with National and Local regulations. - Is insoluble in water. - Is soluble in aromatic hydrocarbons Returning products Customers and stockists are reminded that under EC Health, Safety and Environment Law, when returning products to Spirax Sarco they must provide information on any hazards and the precautions to be taken due to contamination residues or mechanical damage which may present a health, safety or environmental risk. This information must be provided in writing including Health and Safety data sheets relating to any substances identified as hazardous or potentially hazardous. 4 IM-P ST Issue 4
5 2. General product information 2.1 General description The AVM7 is a balanced pressure thermostatic air vent suitable for use on systems up to 7 bar g (101.5 psi g). The air vent is manufactured in AISI 316L stainless steel with a typical surface finish of Ra. Normal operation is close to saturated steam temperature, with complete air removal. Materials All wetted parts are manufactured from FDA and USP Class VI approved materials. Options Special connections to suit most piping systems at an extra cost. Please note that seat end spares for specially requested connections will require a minimum order quantity. Standards The AVM7 has been designed in general accordance with ASME BPE. The unit also complies with the requirements of the European Pressure Equipment Directive 97/23/EC. All elastomers used comply with FDA CFR title 21, paragraph 177 section 2600 and USP Class VI. Certification This product is available with certification to EN Note: All certification/inspection requirements must be stated at the time of order placement. Note: for further product data see Technical Information Sheet TI-P Sizes / pipe connections ¼", ½", ¾" and 1" screwed BSP or NPT. ½", ¾" and 1" O/D x 16 swg (0.065") wall thickness tube butt weld. ½", ¾" and 1" sanitary clamp compatible hygienic connection. DIN (Series 1) tube butt weld ends 12 mm O/D x 1.0 mm wall thickness tube butt weld (DN10-D) 18 mm O/D x 1.0 mm wall thickness tube butt weld (DN15-D) ISO 1127 (Series 1) tube butt weld ends 13.5 mm O/D x 1.6 mm wall thickness tube butt weld (DN8-I) 17.2 mm O/D x 1.6 mm wall thickness tube butt weld (DN10-I) 21.3 mm O/D x 1.6 mm wall thickness tube butt weld (DN15-I) Note: On request other connection options are available at extra cost. Please note that seat end spares for specially requested connections will require a minimum order quantity - Please consult Spirax Sarco for further information. Fig. 1 AVM7 IM-P ST Issue 4 5
6 2.3 Pressure/ temperature limits Temperature C The product should not be used in this region as damage to the internals may occur. Body design conditions Pressure psi g Steam saturation curve Pressure bar g PMA Maximum allowable pressure 7 bar 170 C (101.5 psi 338 F) TMA Maximum allowable temperature bar g ( psi g) Minimum allowable temperature -10 C (14 F) PMO Maximum operating pressure 7 bar g (101.5 psi g) for saturated steam service TMO Maximum operating temperature 170 C (338 F) Minimum operating temperature 0 C (32 F) Designed for a maximum cold hydraulic test pressure 10.5 bar g (152.3 psi g) 3. Installation Note: Before actioning any installation observe the 'Safety information' in Section 1. Referring to the Installation and Maintenance Instructions, name-plate and Technical Information Sheet, check that the product is suitable for the intended installation: 3.1 Check materials, pressure and temperature and their maximum values. If the maximum operating limit of the product is lower than that of the system in which it is being fitted, ensure that a safety device is included in the system to prevent overpressurisation. 3.2 Determine the correct installation situation and the direction of fluid flow. 3.3 Remove protective covers from all connections and the protective film from all name-plates, where appropriate, before installation on steam or other high temperature applications. 3.4 The product is designed for installation in vertical lines with the flow upwards to ensure self-draining operation. Do not expose the element to superheat conditions since over expansion may result. Suitable isolation valves must be installed to allow for safe maintenance /replacement. Open isolation valves slowly until normal operating conditions are achieved. Check for leaks. Caution: In order to prevent undue stresses on the pipeline and air vent, ensure adequate provision is made for thermal expansion. Note: The body and element must be handled carefully to ensure that surfaces are not damaged. If the trap is to discharge to atmosphere ensure it is to a safe place, the discharging fluid may be at a temperature of 100 C (212 F). Temperature F PN7 6 IM-P ST Issue 4
7 4. Commissioning After installation or maintenance ensure that the system is fully functional. Carry out tests on any alarms or protective devices. 5. Operation The operating element is a capsule containing a small quantity of a special liquid with a boiling point below that of water. In the cold conditions that exist at start-up, the capsule is relaxed. The valve is off its seat and is wide open, allowing unrestricted removal of air. As air passes through the product, heat is transferred to the liquid in the capsule. The fill liquid boils before steam reaches the trap. The vapour pressure within the capsule causes it to expand and the unit shuts. 6. Maintenance Note: Before actioning any maintenance program observe the 'Safety information' in Section General information Before undertaking any maintenance on the product it must be isolated from the supply line and return line and any pressure allowed to safely normalise to atmosphere. The product should then be allowed to cool. When reassembling, ensure that all joint faces are clean. Always ensure the correct tools, safety procedures and protective equipment are used at all times. 6.2 How to fit new internals: - Remove nuts and bolts. - The end connection with internal seat, gasket and capsule assembly can then be removed for cleaning or replacement. Ensure that the capsule on reassembly is fitted in the correct position (see Figure 2, page 8). - Reassemble using a new gasket and with the valve head in position to close onto the seat orifice. - Replace nuts and bolts and tighten them to the recommended torque (see Table 1) and put back into service. - Open isolation valves slowly until normal operating conditions are achieved. - Check for leaks. Table 1 Recommended tightening torques Item Part N m (lbf ft) or mm 5 Nuts and bolts 8 A/F M5 3-4 ( ) IM-P ST Issue 4 7
8 7. Spare parts Available spares are shown in solid outline. Parts drawn in broken lines are not available as spares. Available spares Element assembly 2 'O' ring (packet of 3) 3 How to order spares Always order spares by using the description given in the column headed 'Available spares' and state the size, type and end connection of the unit. Example: 1 - Element assembly for a Spirax Sarco ½" AVM7 stainless steel thermostatic air vent having screwed NPT connections ('O' ring) Fig IM-P ST Issue 4
BTM7, BTS7 and BTS7.1 Stainless Steel Thermostatic Clean Steam Traps
1801050/10 IM-P180-05 ST Issue 10 BTM7, BTS7 and BTS7.1 Stainless Steel Thermostatic Clean Steam Traps Installation and Maintenance Instructions 1. Safety information 2. General product information 3.
MST21 Stainless Steel Balanced Pressure Thermostatic Steam Trap
1250650/6 IM-P125-07 ST Issue 6 MST21 Stainless Steel Balanced Pressure Thermostatic Steam Trap Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation
TSS21 Sealed Thermostatic Steam Tracer Trap
1255050/4 IM-P125-10 ST Issue 4 TSS21 Sealed Thermostatic Steam Tracer Trap Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
BT6HC Hygienic Sanitary Balanced Pressure Steam Trap for High Capacity and CIP/SIP Applications
1800350/6 IM-P180-12 ST Issue 6 BT6HC Hygienic Sanitary Balanced Pressure Steam Trap for High Capacity and CIP/SIP Applications Installation and Maintenance Instructions 1. Safety information 2. General
AVC32 Carbon Steel Air Vent for Steam Systems
1234050/4 IM-P123-14 ST Issue 4 AVC32 Carbon Steel Air Vent for Steam Systems Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
CVS10 Sanitary Check Valves
0299050/4 IM-P029-11 ST Issue 4 CVS10 Sanitary Check Valves Installation and Maintenance Instructions 1. Safety information CVS10 with soft seat 2. General product information 3. Operation 4. Installation
Fig 12, Fig 14HP, Fig 16, Fig 16HP and Fig 16L Strainers
16355/11 IM-S6-17 ST Issue 11 Fig 12, Fig 14HP, Fig 16, Fig 16HP and Fig 16L Strainers Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4.
DCV10 Stainless Steel Disc Check Valve for use with Condensate Pumps
6018050/1 IM-P601-33 ST Issue 1 DCV10 Stainless Steel Disc Check Valve for use with Condensate Pumps Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation
DF1 and DF2 Diffusers
1550650/4 IM-P155-07 ST Issue 4 and Diffusers Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning 5. Operation 6. Maintenance
Fig 1, Fig 12, Fig 13, Fig 14HP, Fig 16, Fig 16HP and Fig 16L Strainers
16355/8 IM-S6-17 ST Issue 8 Fig 1, Fig 12, Fig 13, Fig 14HP, Fig 16, Fig 16HP and Fig 16L Strainers Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation
S1, S2, S3, S5, S6, S7, S8, S12 and S13 Separators
0231150/8 IM-P023-55 ST Issue 8 S1, S2, S3, S5, S6, S7, S8, S12 and S13 Separators Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
FTGS14 Ball Float Steam Trap DN15 (½") to DN25 (1")
1458050/5 IM-P145-12 ST Issue 5 FTGS14 Ball Float Steam Trap DN15 (½") to DN25 (1") Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
TP1 and TP2 Temporary Cone Shaped Strainers
1698051/2 IM-P169-07 ST Issue 2 TP1 and TP2 Temporary Cone Shaped Strainers Installation and Maintenance Instructions TP1 1. Safety information 2. General product information 3. Installation and commissioning
TA10A and TA10P Steam Tracing Temperature Control Valves Installation and Maintenance Instructions
3500032/2 IM-P350-02 CH Issue 2 TA10A and TA10P Steam Tracing Temperature Control Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4.
Spiratec ST14, ST16 and ST17 Sensor Chambers and sensors
0862050/1 IM-P086-18 MI Issue 1 Spiratec ST14, ST16 and ST17 Sensor Chambers and sensors Installation and Maintenance Instructions 1. Safety Information 2. General product information 3. Installation 4.
IFTGS14 Ball Float Steam Trap ½" and ¾" with Integral Spiratec Sensor
6150350/3 IM-P615-12 ST Issue 3 IFTGS14 Ball Float Steam Trap ½" and ¾" with Integral Spiratec Sensor Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation
PV4 and PV6 Piston Valves
1181250/1 IM-P118-05 ST Issue 1 PV4 and PV6 Piston Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning 5. Operation 6.
DCV1, DCV3 and DCV3LT Disc Check Valves Installation and Maintenance Instructions
1340050/7 IM-P134-07 CMGT Issue 7 DCV1, DCV3 and DCV3LT Disc Check Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
KBV21i and KBV40i Key Operated Boiler Blowdown Valves Installation and Maintenance Instructions
4059051/3 IM-P405-48 EMM Issue 3 KBV21i and KBV40i Key Operated Boiler Blowdown Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4.
KBV21i and KBV40i Air Actuated Boiler Blowdown Valves
4059051/1 IM-P405-48 AB Issue 1 KBV21i and KBV40i Air Actuated Boiler Blowdown Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
AE14 Automatic Air Vents for Liquid Systems Installation and Maintenance Instructions
1490050/7 IM-P149-06 CMGT Issue 7 AE14 Automatic Air Vents for Liquid Systems Installation and Maintenance Instructions 1. General safety information 2. General product information 3. Installation 4. Commissioning
DCV6 Disc Check Valve
1342050/6 IM-P134-22 ST Issue 6 DCV6 Disc Check Valve Installation and Maintenance Instructions Printed IM-P134-22 in the UK ST Issue 6 Copyright 20101 Safe operation of this product can only be guaranteed
UIB30 and UIB30H Sealed Inverted Bucket Steam Traps for use with Pipeline Connectors
1130050/4 IM-P113-02 ST Issue 4 UIB30 and UIB30H Sealed Inverted Bucket Steam Traps for use with Pipeline Connectors Installation and Maintenance Instructions 1. Safety information 2. General product information
HM and HM34 Inverted Bucket Steam Traps Installation and Maintenance Instructions
0670350/4 IM-S03-11 ST Issue 4 HM and HM34 Inverted Bucket Steam Traps Installation and Maintenance Instructions 1. Safety information 2. General product information HM Series 3. Installation 4. Commissioning
Dri-Line Mk3 Monnier Compressed Air Drain Trap
5044050/2 IM-P504-24 CH Issue 2 Dri-Line Mk3 Monnier Compressed Air Drain Trap Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation and Operation
BT6-B Sanitary Balanced Pressure Thermostatic Steam Trap
1802950/7 IM-P180-31 ST Issue 7 BT6-B Sanitary Balanced Pressure Thermostatic Steam Trap Installation and Maintenance Instructions 1. Safety information 2. General Product information 3. Installation 4.
Dri-Line Mk2 Spirax-Monnier Compressed Air Drain Trap
0509950/2 IM-P050-21 CH Issue 2 Dri-Line Mk2 Spirax-Monnier Compressed Air Drain Trap Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation and
CA44, CA44S, CA46 and CA46S Air and Gas Traps
1484450/3 IM-P148-37 ST Issue 3 CA44, CA44S, CA46 and CA46S Air and Gas Traps Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
MSC-P and MSC-N Manifolds for Steam Distribution and Condensate Collection
1170850/1 IM-P117-36 ST Issue 1 MSC-P and MSC-N Manifolds for Steam Distribution and Condensate Collection Installation and Maintenance Instructions 1. Safety information 2. General product information
CS10-1 Stainless Steel Clean Steam Separator
0232950/2 IM-P023-60 ST Issue 2 CS10-1 Stainless Steel Clean Steam Separator Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
AVS32 Stainless Steel Air Vent for Steam Systems Installation and Maintenance Instructions
1234150/3 IM-P123-17 ST Issue 3 AVS32 Stainless Steel Air Vent for Steam Systems Installation and Maintenance Instructions 1. General safety information 2. General product information 3. Installation 4.
Fig 3, 7, 33, 34, 34HP, 36, 36HP, 37, 3616 and Fig 3716 Flanged Strainers
16352/8 IM-S6-18 ST Issue 8 Fig 3, 7, 33, 34, 34HP, 36, 36HP, 37, 3616 and Fig 3716 Flanged Strainers Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation
S1, S2, S3, S5, S6, S7, S8, S12 and S13 Separators Installation and Maintenance Instructions
PREVIOUS REFERENCE NO. IMP02355 0231150/13 IMF0501ENISS2 CMGT S1, S2, S3, S5, S6, S7, S8, S12 and S13 Separators Installation and Maintenance Instructions 1. Safety information 2. General product information
BPT13 Balanced Pressure Thermostatic Steam Traps
1229250/10 IM-P122-02 ST Issue 10 BPT13 Balanced Pressure Thermostatic Steam Traps Installation and Maintenance Instructions BPT13A and BPT13AX BPT13S and BPT13SX BPT13UA and BPT13UAX BPT13US and BPT13USX
CP10 Sensor Installation and Maintenance Instructions
4030150/9 IM-P403-26 EMM Issue 9 CP10 Sensor Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Maintenance 5. Spare parts Copyright 2017
Airodyn, BRair and BRoil Compressed Air Drain Traps
6100550/3 IM-S48-06 ST Issue 3 Airodyn, BRair and BRoil Compressed Air Drain Traps Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
S and SF Inverted Bucket Steam Traps
0772150/6 IM-P077-02 ST Issue 6 S and SF Inverted Bucket Steam Traps Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning 5. Operation
AE30 Automatic Air Eliminators / Air and Gas Vents for Liquid Systems
0170651/ 10 IM-P017-08 ST Issue 10 AE30 Automatic Air Eliminators / Air and Gas Vents for Liquid Systems Installation and Maintenance Instructions 1. Safety information 2. General product information 3.
Fig 7, 33, 33.1, 34, 34HP, 36, 36HP, 37, 3616 and Fig 3716 Flanged Strainers Installation and Maintenance Instructions
16352/11 IM-S6-18 ST Issue 11 Fig 7, 33, 33.1, 34, 34HP, 36, 36HP, 37, 3616 and Fig 3716 Flanged Strainers Installation and Maintenance Instructions 1. Safety information 2. General product information
SA121, SA122, SA123, SA128 and SA1219 Self-acting Temperature Control Systems (Dial Adjustment)
3820050/4 IM-P382-01 CH Issue 4 SA121, SA122, SA123, SA128 and SA1219 Self-acting Temperature Control Systems (Dial Adjustment) Installation and Maintenance Instructions 1. Safety information 2. Use 3.
SA121, SA122, SA123, SA128 and SA1219 Self-acting Temperature Control Systems (Knob Adjustment)
3810050/5 IM-P381-01 CH Issue 5 SA121, SA122, SA123, SA128 and SA1219 Self-acting Temperature Control Systems (Knob Adjustment) Installation and Maintenance Instructions 1. Safety information 2. Use 3.
TD62LM and TD62M Thermodynamic Steam Traps with Replaceable Seats
0686550/4 IM-P068-58 ST Issue 4 TD62LM and TD62M Thermodynamic Steam Traps with Replaceable Seats Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation
UBP32 Sealed Balanced Pressure Thermostatic Steam Trap for use with PC_ Pipeline Connectors Installation and Maintenance Instructions
1270750/7 IM-P127-02 ST Issue 7 UBP32 Sealed Balanced Pressure Thermostatic Steam Trap for use with PC_ Pipeline Connectors Installation and Maintenance Instructions 1 General safety information 2 General
FV Flash Vessel Installation and Maintenance Instructions
4041050/5 IM-P404-10 EMM Issue 5 FV Flash Vessel Installation and Maintenance Instructions 1. Safety information 2. Specific product safety information 3. Product information 4. Installation 5. Commissioning
TDC46M, TDS46M and UTDS46M Thermodynamic Steam Traps with Maintainable Seat Installation and Maintenance Instructions
1870050/7 IM-P187-05 CMGT Issue 7 TDC46M, TDS46M and UTDS46M Thermodynamic Steam Traps with Maintainable Seat Installation and Maintenance Instructions TDC46M and TDS46M UTDS46M 1. Safety information 2.
M70i ISO and M80i ISO Stainless Steel Ball Valves for Sanitary Systems Installation and Maintenance Instructions
1820050/3 IM-P182-07 CMGT Issue 3 M70i ISO and M80i ISO Stainless Steel Ball Valves for Sanitary Systems Installation and Maintenance Instructions 1. Safety information 2. General product information M70i
CA10S, CA14 and CA14S Air and Gas Traps
1448150/9 IM-P148-13 ST Issue 9 CA10S, CA14 and CA14S Air and Gas Traps Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning 5.
FT16 Ball Float Steam Trap Installation and Maintenance Instructions
1430050/1 IM-P143-04 ST Issue 1 FT16 Ball Float Steam Trap Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation ½" and ¾" shown 4 Commissioning
SRV66 Sanitary Pressure Reducing Valve
1866350/4 IM-P186-09 CH Issue 4 SRV66 Sanitary Pressure Reducing Valve Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Operation 5. Commissioning
M10HTi ISO Tobacco Ball Valve Screwed, SW, BW and Flanged versions
IM-P133-75 ST Issue 1 M10HTi ISO Tobacco Ball Valve Screwed, SW, BW and Flanged versions Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4.
MF2M Monnier Miniature Compressed Air Filter
5040050 / 2 IM-P504-02 CH Issue 2 MF2M Monnier Miniature Compressed Air Filter Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation and commissioning
M33F ISO, M33S ISO and M33V ISO Ball Valves Installation and Maintenance Instructions
BAC13365 IM-P133-65 CMGT Issue 2 M33F ISO, M33S ISO and M33V ISO Ball Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
IX1 Spirax-Monnier International Compressed Air Filter Installation and Maintenance Instructions
0575050/2 IM-P057-04 CH Issue 2 IX1 Spirax-Monnier International Compressed Air Filter Installation and Maintenance Instructions 1 Safety information 2 General product information 3 Installation and commissioning
PC10HP Pipeline Connector (ASME 600)
1280051/2 IM-P128-13 ST Issue 2 PC10HP Pipeline Connector (ASME 600) Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning 5. Spare
BTD52L Thermodynamic Steam Trap Installation and Maintenance Instructions
1810050/4 IM-P181-03 ST Issue 4 BTD52L Thermodynamic Steam Trap Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation 4 Commissioning 5 Operation
FT53, IFT53, FT54, IFT54, FT57 and IFT57 Ball Float Steam Traps - DIN
6030050/6 IM-P603-03 ST Issue 6 FT53, IFT53, FT54, IFT54, FT57 and IFT57 Ball Float Steam Traps - DIN Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation
TD62LM and TD62M Thermodynamic Steam Traps with Replaceable Seats Installation and Maintenance Instructions
PREVIOUS REFERENCE NO. IM-P068-58 0686550/5 IM-P015-04-EN-ISS2 CMGT TD62LM and TD62M Thermodynamic Steam Traps with Replaceable Seats Installation and Maintenance Instructions 1. Safety information 2.
APT14, APT14HC and APT14SHC Spares 2
6120251/7 IM-P612-06 ST Issue 7 APT14, APT14HC and APT14SHC Spares 2 Installation and Maintenance Instructions 1. Safety information 2. Replacement of trap and outlet check valve mechanism 3. Replacement
CA16 and CA16S-14 Air and Gas trap Installation and Maintenance Instructions
1483250/3 IM-P148-10 ST Issue 3 CA16 and CA16S-14 Air and Gas trap Installation and Maintenance Instructions 1 General safety information CA16 and CA16S-14 ½" and ¾" 2 General product information 3 Installation
Thermocirc Installation and Maintenance Instructions
1570072/2 IM-P157-36 ST Issue 2 Thermocirc Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation 4 Commissioning 5 Operation 6 Maintenance
SCA Series Inverted Bucket Steam Traps
0770050/5 IM-P077-06 ST Issue 5 SCA Series Inverted Bucket Steam Traps Installation and Maintenance Instructions 1. General safety information 2. General product information 3. Installation 4. Commissioning
ML3M Monnier Miniature Compressed Air Lubricator
5041050/3 IM-P504-04 CH Issue 3 ML3M Monnier Miniature Compressed Air Lubricator Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation and commissioning
BCV31 DN40 - Blowdown Control Valve
4034850/5 IM-P403-71 AB Issue 5 BCV31 DN40 - Blowdown Control Valve Installation and Maintenance Instructions 1. Safety information 2. Application 3. Technical data 4. Operation 5. Installation 6. Flow
Manual Actuated Boiler Blowdown Valves
Manual Actuated Boiler Blowdown Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Operation 5. Maintenance 6. Spare parts p.1 1. Safety
TW Temperature Control Valve
0470050/6 IM-P047-04 CH Issue 6 TW Temperature Control Valve Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Maintenance 5. Spare parts
SRV2S Pressure Reducing Valve
1860050/4 IM-P186-03 CH Issue 4 SRV2S Pressure Reducing Valve Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Maintenance 5. Spare parts
BDV1 and BDV2 Blowdown / Depressurisation Valves
6000050/8 IM-P600-02 ST Issue 8 BDV1 and Blowdown / Depressurisation Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation BDV1 4. Commissioning
USM21 Sealed Bimetallic Steam Trap for use with Pipeline Connectors Installation and Maintenance Instructions
6250250/1 IM-P625-03 ST Issue 1 USM21 Sealed Bimetallic Steam Trap for use with Pipeline Connectors Installation and Maintenance Instructions 1. General safety information 2. General product information
TD45 Thermodynamic Steam Trap Installation and Maintenance Instructions
0685255/1 IM-P068-47 ST Issue 1 TD45 Thermodynamic Steam Trap Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation 4 Commissioning 5 Operation
MFP14-PPU (Vented) Automatic Packaged Pump Units
681060/2 IM-P681-02 ST Issue 2 MFP14-PPU (ented) Automatic Packaged Pump Units Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Single MFP14 - PPU installation
Spirax Compact FREME Flash Recovery Energy Management Equipment
IM-UK-cFREME UK Issue 1 Spirax Compact FREME Flash Recovery Energy Management Equipment Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4.
Spirax SafeBloc TM DBB3 Double Block and Bleed Bellows Sealed Stop Valve. 1. Safety information. 2. General product information. 3.
1849050/3 IM-P184-09 ST Issue 3 Spirax SafeBloc TM DBB3 Double Block and Bleed Bellows Sealed Stop Valve Installation and Maintenance Instructions 1. Safety information 2. General product information 3.
SA Control Valve types: BM, BMF, BX, SB, NS, KA, KB, KC (Normally open) BMRA, BMFRA, BXRA, SBRA, NSRA, KX, KY (Normally closed)
0366055/7 IM-S21-01 CH Issue 7 SA Control Valve types: BM, BMF, BX, SB, NS, KA, KB, KC (Normally open) BMRA, BMFRA, BXRA, SBRA, NSRA, KX, KY (Normally closed) Installation and Maintenance Instructions
Fig 1, Fig 12, Fig 13, Fig 14, Fig 16 and Fig 16L Strainers Installation and Maintenance Instructions
16355/5 IM-S6-17 ST Issue 5 Fig 1, Fig 12, Fig 13, Fig 14, Fig 16 and Fig 16L Strainers Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation
FT43, FT44, FT46 and FT47 Ball Float Steam Traps Installation and Maintenance Instructions
0667050/11 IM-S02-30 ST Issue 11 FT43, FT44, FT46 and FT47 Ball Float Steam Traps Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
BRV71 and BRV73 Pressure Reducing Valves
2103050/4 IM-P210-04 CH Issue 4 BRV71 and BRV73 Pressure Reducing Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Start-up and adjustment
BCV31 DN20 - Blowdown Control Valve
4034650/8 IM-P403-37 AB Issue 8 BCV31 DN20 - Blowdown Control Valve Installation and Maintenance Instructions 1. Safety information 2. Application 3. Technical data 4. Operation 5. Installation 6. Flow
1. General safety information. 2. General product information. 3. Installation. 4. Commissioning. 5. Operation. 6. Maintenance. 7.
0170550/5 IM-P017-03 ST Issue 5 AE36 and AE36A Automatic Air Eliminators/ Air Vents for Liquid Systems Installation and Maintenance Instructions 1. General safety information 2. General product information
TD10, TD52M and TD259 Thermodynamic Steam Traps Installation and Maintenance Instructions
6875/3 IM-P68-31 ST Issue 3 TD1, TD52M and TD259 Thermodynamic Steam Traps Installation and Maintenance Instructions 1 General safety information TD1 2 General product information 3 Installation 4 Commissioning
Type 130 and HL10 'Safeguard High Limit Control' Installation and Maintenance Instructions
0730042/6 IM-P073-08 CH Issue 6 Type 130 and HL10 'Safeguard High Limit Control' Installation and Maintenance Instructions 1. General safety information 2. General product information 3. Installation 4.
Vane Flow Switches Colima FLU Series
3.797.5275.200 CH Issue 2-2016 Vane Flow Switches Colima FLU Series Installation and Maintenance Instructions 1. General safety information 2. General product information 3. Installation and Maintenance
A3S Bellows Sealed Stop Valve Installation and Maintenance Instructions
1326050/3 IM-P132-11 ST Issue 3 A3S Bellows Sealed Stop Valve Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation 4 Commissioning 5 Operation
AE50S Automatic Air and Gas Vent for Liquid Systems Installation and Maintenance Instructions
0176050/3 IM-P017-11 ST Issue 3 AE50S Automatic Air and Gas Vent for Liquid Systems Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation 4
BSA6T and BSA64T Stainless Steel Bellows Sealed Stop Valves Installation and Maintenance Instructions
1843950/3 IM-P184-03 ST Issue 3 BSA6T and BSA64T Stainless Steel Bellows Sealed Stop Valves Installation and Maintenance Instructions 1. General safety information 2. General product information 3. Installation
FTC62 and FTS62 Ball Float Steam Traps Installation and Maintenance Instructions
1792050/2 IM-P179-15 ST Issue 2 FTC62 and FTS62 Ball Float Steam Traps Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning 5.
MPC1M, MPC2M and MPC2AM Monnier High Efficiency Compressed Air Filter / Regulators
5043150 /2 IM-P504-08 CH Issue 2 MPC1M, MPC2M and MPC2AM Monnier High Efficiency Compressed Air Filter / Regulators Installation and Maintenance Instructions 1. Safety information 2. General product information
STERI-TROL Clean Service 'S' Series Two-port Control Valves DN15 (½") to DN100 (4")
18050/2 IM-P183-03 CH Issue 2 STERI-TROL Clean Service 'S' Series Two-port Control Valves DN15 (½") to DN100 (4") Installation and Maintenance Instructions 1. Safety information 2. General product information
IP2M, IP2AM and IP2DM Monnier International Compressed Air Filter/ Regulators
5043250/2 IM-P504-18 CH Issue 2 IP2M, IP2AM and IP2DM Monnier International Compressed Air Filter/ Regulators Installation and Maintenance Instructions 1. Safety information 2. General product information
QuickHeat TM Packaged Heat Exchanger Solutions
4831999/1 IM-P483-03 CH Issue 1 QuickHeat TM Packaged Heat Exchanger Solutions Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
M45 ISO Ball Valve DN25 to 150 Installation and Maintenance Instructions
BAC 13310 IM-P133-42 ST Issue 2 M45 ISO Ball Valve DN25 to 150 Installation and Maintenance Instructions 1. General safety information 2. General product information 3. Installation 4. Commissioning 5.
PC3000, PC3001 and PC4000, PC4001 Pipeline Connectors
1285550/1 IM-P128-35 ST Issue 1 PC3000, PC3001 and PC4000, PC4001 Pipeline Connectors Installation and Maintenance Instructions 1. Safety information 2. Description 3. Installation 4. Welding of pipeline
SRV461S and SRV463S Stainless Steel Direct Acting Pressure Reducing Valves
1861050/5 IM-P186-02 H Issue 5 SRV461S and SRV463S Stainless Steel irect Acting Pressure Reducing Valves Installation and Maintenance Instructions 1. Safety information 2. Product information 3. Installation
BCVi43 Blowdown Control Valve
BCVi43 Blowdown Control Valve Installation and Maintenance Instructions IM-UK-BCVi43 UK Issue 2 1. Safety information 2. General product information and application 3. Technical data 4. Operation 5. Installation
M111 Spiraflo Transducer
3309551/ 7 IM-P330-38 MI Issue 7 M111 Spiraflo Transducer Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Technical data 4. Mechanical installation: M111
LP31 Level Probe. 1. Safety information. 2. General product information. 3. Installation. 4. Wiring. 5. Maintenance
404151/7 IM-P40-80 AB Issue 7 LP1 Level Probe Installation and Maintenance Instructions 1. Safety information. General product information. Installation 4. Wiring 5. Maintenance IM-P40-80 Printed in the
BSA and BSAT Bellows Sealed Stop Valves Installation and Maintenance Instructions
1370050/10 IM-P137-02 ST Issue 10 BSA and BSAT Bellows Sealed Stop Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning
CA46S Austenitic Stainless Steel Air and Gas Trap DN40 and DN50
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
Colima TOR Magnetic Level Switches
3.793.5275.200 IM-P324-03 CH Issue 1 Colima TOR Magnetic Level Switches Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation and Maintenance 4.
BDV60 Blowdown Vessel Installation and Maintenance Instructions
4050150/8 IM-P405-31 EMM Issue 8 BDV60 Blowdown Vessel Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning 5. Operation 6. Maintenance
RJ check valves Installation and Maintenance Instructions
3.531.5275.200 Issue 3-2015 RJ check valves Installation and Maintenance Instructions The PED Directive 97/23/EC is repealed and replaced by the new PED Directive 2014/68/EU with effect from 19 July 2016.