Aftercooler Owner s Manual

Transcription

1 Aftercooler Owner s Manual SUPERIOR PERFORMANCE And Quality In Blast Cleaning Equipment! WARNING Read Manual Failure to read, understand & follow all safety and operation procedures in this manual can cause injury or death. Manuals that are lost, incomplete, or damaged, must be replaced immediately. Manual # AC1708 Ph: (780) Fax: (780) Copyright 2017 Mod-U-Blast, All Rights Reserved

2 Dry-Pro Skid Mounted Moisture Removal Package IMPORTANT WARNINGS Warning: DO NOT OPERATE THIS EQUIPMENT OVER 200 PSI Danger: DO NOT ATTEMPT TO REMOVE OR REPAIR ANY PART OF THE SYSTEM UNITIL IT IS COMPLETELY DEPRESURIZED. SERIOUS PERSONAL INJURY OR DEATH MAY RESULT IF THIS RULE IS NOT FOLLOWED OPERATION 1. Connect an air hose from the air supply to the inlet side of the aftercooler. 2. Connect an air hose from the aftercooler skid outlet to the equipment air inlet. 3. Start the compressor. 4. Slowly open the air inlet ball valve to pressurize the system. 5. Adjust the regulator for the air motor on the Filter-Regulator-Lubricator (FRL) (Instructions next page) to read the working pressure (PSI) on the label. NOTE: On hot days run the air motor at maximum pressure. (see chart next page) 6. Adjust the oil output on the lubricator (Clear Dial) by turning clockwise or counter clockwise until there is the required drops of oil every minute. (see chart next page) 7. Open the air supply to the equipment. (if ball valve is equipped) 8. Slightly open the ball valve for the moisture separator (black canister) and let it drain while using the unit. NOTE: COLD WEATHER OPERATION - The fan air motor should be regulated so that the aftercooler temperature gauge reads above 0 C to avoid freezing the core assembly. The aftercooler has a drain installed for cold weather climate areas and should be drained after every use to avoid core damage. Leave the aftercooler drain open when not in use. Parts Ordering: Copyright 2017 Mod-U-Blast, All Rights Reserved

3 FRL Filter Do Not Fill With Oil Lubricator Fill to Line on Glass With ATF Regulator Pull down on knob to adjust Push up to lock Pressure & CFM Requirements for Aftercooler Air Motors NOTE: Working pressure is at 21 C (70 F) ambient temperature. In warmer weather the air motors can be operated up to or at the maximum pressure. SHUT DOWN 1. Close the ball valve on the outlet side of the aftercooler package or at the equipment. (if equipped) 2. Shut down the air supply to the aftercooler package. 3. Open the drains for the aftercooler, coalescer and moisture separator. 4. After the air is removed, close the air inlet ball valve. 5. Leave all the drains open while storing. 3 Copyright 2017 Mod-U-Blast, All Rights Reserved

4 THERMOMETER AFTERCOOLER DIFFERENTIAL PRESSURE GAUGE FRL MOISTURE FILTER AIR INLET AIR OUTLET COALESCER DRAINS DSA-250MS-M Shown here 4 Copyright 2017 Mod-U-Blast, All Rights Reserved

5 PARTS LIST Description Stock # DSA250MS-M DSA450MS-M DSA750MS-M DSA1000MS-M DSA1600MS-M QTY QTY QTY QTY QTY Thermometer FRL Pressure Gauge Air Motor for Aftercooler DAC-AMV Air Motor for Aftercooler DAC-AM6 1 Air Motor for Aftercooler DAC-AM16 1 Aftercooler (w/o air motor) DAC Aftercooler (w/o air motor) DAC Aftercooler (w/o air motor) DAC Aftercooler (w/o air motor) DAC Aftercooler (w/o air motor) DAC MUB* DSC-250-DEL 1 - MUB* DSC-450-DEL 1 - MUB* DSC-750-DEL 1 - MUB* DSC-1000-DEL 1 - MUB* DSC-1600-DEL 1 Coalescer Differential Pressure Gauge - MUB* DSC-DPG *MUB - Mod-U-Blast Model (Red) Note: These skid units may have been substituted with AKG aftercoolers which will be labeled. Our regular MUB coalescers are RED in colour all others would be gold or white. Please check the unit to see what is installed before ordering. All units with AKG aftercoolers and non MUB coalescers please contact your Mod-U-Blast sales representative for price and availability. For Parts Call and Ask For The Order Desk 5 Copyright 2017 Mod-U-Blast, All Rights Reserved

6 Warranty Mod-U-Blast equipment is covered by a one (1) year warranty against defects in material and workmanship starting from the purchase date. This covers the equipment as well as all major components. This warranty does not apply to abnormal use of the equipment or parts. Parts considered consumables are not covered by warranty. Claims will be honored only if the warranty card is returned within a period of two (2) months from the factory shipping date. The card can be returned to your Mod-U-Blast salesperson or mailed to the address below. In the event of failure of this equipment please contact a Mod-U-Blast service centre or call (780) Avenue NW Edmonton, Alberta Canada T6P 0C2 PH: (780) FAX: (780) Copyright 2017 Mod-U-Blast, All Rights Reserved