@- A WARNING & ALL RANGES CAN TIP INJURY TO PERSONS COULD RESULT INSTALL ANTI-TIP DEVICE PACKED WITH RANGE SEE INSTALLATION INSTRUCTIONS Quick Reference Tabe of Contents: Pages 111 Before you start m piiziq I (II m1-r6] E-171 Product dimensions Cabinet dimensions/requirements 12] Eectrica requirements 12] Gas suppy requirements Instaation steps Gas conversions If range does not operate If you need assistance/service I] Moving the range If you need assistance: Check your Use and Care Guide for a to-free number to ca or ca the deaer from whom you purchased this range. The deaer is isted in the Yeow Pages of your phone directory under Appiances - Househod - Major - Service and Repair. Ca when you: q Have questions about range instaation or operation. q Need to obtain the name and number of an authorized service company. When you ca, you wi need: q The range mode number.,vj The range seria number. Both numbers are isted on the mode/seria the frame behind the broier door. rating pate ocated on
Important: Observe a governing codes and ordinances. This instaation must conform with a oca codes and ordinances. In the absence of oca codes, instaation must conform with American Nationa Standard, Nationa Fue Gas Code ANSI 2223.1 - atest edition**. Proper instaation is your responsibiity. A quaified technician must insta this range. Make sure you have everything necessary for correct instaation. It is the instaer s responsibiity to compy with instaation cearances specified on the gas information abe. The gas information abe and mode/seria rating pate are ocated on the frame behind the broier door. Check ocation where range wi be instaed. The range shoud be ocated away from strong draft areas, such as windows, doors and strong heating vents or fans. The range shoud be ocated for convenient use in kitchen. ALL OPENINGS IN THE WALL OR FLOOR WHERE RANGE IS TO BE INSTALLED MUST BE SEALED. Cabinet opening dimensions shown must be used. Given dimensions are minimum cearances. Grounded eectrica outet is required. See Eectrica requirements, Page 2. Proper gas suppy connection must be avaiabe. See Gas suppy requirements, Page 2. - i 36 cooktop height 46-718 overa height I WARNING: If the information in this manua is not foowed exacty, a fire or exposion may resut causing property damage, persona injury or death. - Do Not store or use gasoine, or other fammabe vapors and iquids in the vicinity of this or any other appiance. - WHAT TO DO IF YOU SMELL GAS: Do Not try to ight any appiance. Do Not touch any eectrica switch; Do Not use any phone in your buiding. Immediatey ca your gas suppier from a neighbor s phone. Foow gas suppier s instructions. m If you cannot reach your gas suppier, ca the fire department. - Instaation and service must be done by a quaified instaer, service agency or the gas suppier ah * Eectrica Shock Hazard It is the customer s responsibiity to contact a quaified eectrica instaer and to make sure that the eectrica instaation is adequate and make sure the eectrica instaation foows the Nationa Eectrica Code, ANWNFPA 70 - atest edition*, and a oca codes and ordinances. Take specia care when cutting hoes in wa or foor. Eectrica wires may be behind the wa or foor covering and cause eectrica shock if you touch them. Locate any eectrica circuits that coud be affected by the instaation of this product and disconnect power circuit. coud resut in death or serious injury. Fire Hazard Do Not obstruct the fow of combustion or ventiation air. Faiure to foow this instruction coud resut in a fire. Injury Hazard To eiminate the risk of burns or fire, avoid instaing cabinet storage above the cooking surface. If cabinets are aready instaed, reduce the hazard of reaching over a heated Eooking surface by instaing a range hood. The range hood shoud extend a minimum of 5 inches out from the bottom front of the zabinets. Reaching over a heated cooking surface coud?esut in a serious burn or other injury. Page 1 18 min. I cearance upper cabinet to countertop I 2 min.! a countertop t wa or other combustibe Contact a quaified foor covering instaer to check that the foor covering can withstand at east 90-F above room temperature. Use an insuated pad or /4 pywood under range if instaing range over carpeting. Anti-tip bracket 30 min. cabinet opening wix 30-/8 opening F I! The foor-mounted anti-tip bracket MUST be instaed. To insta the anti-tip bracket suppied, see Pages 3-4 and the anti-tip bracket tempate/instruction sheet. Standard, Tite 24 CFR, Part 3280 [formery the Federa Standard for Mobie Home Construction and Safety, Tite 24, HUD (Part 28011 or, when such standard is not appicabe, the Standard for Manufactured Home Instaations, ANSI A225.1 and Manufactured Home Instaations, Sites, and Communities ANSI/NFPA 501A, or with oca codes. When this range is instaed in a mobie home, it must be secured to the foor during transit. Any method of securing the range is adequate as ong as it conforms to the standards isted above. Copies of the standards isted may be obtained from: * Nationa Fire Protection Association Batterymarch Park Quincy, Massachusetts 02269 * American Gas Association 1515 Wison Bouevard Arington, Virginia 22209 area recommended on of rigid gas pipe. pipe and eectrica commended in either shaded area. 0 0 - foor-mounted anti-tip bracket Do Not pinch the power suppy cord between the range and the wa. Do Not sea the range to the side cabinets. If cabinet depth is greater than 24. oven frame must extend beyond cabinet fronts by 112 min. ** Note: 30 min. when bottom of wood or meta cabinet is protected by not ess than /4 fame retardant miboard covered with not ess than No. 28 MSG sheet stee, 0.015 stainess stee, 0.024 auminum or 0.020 copper. 36 min. cearance between the top of the cooking patform and the bottom of an unprotected wood or meta cabinet. 2 screws (HO x -1/2 ) Not shown: - iterature pack - orifice spuds 2 pastic anchors Bracket must be securey mounted to sub-foor. Thickness of fooring may require onger screws to anchor bracket to sub-foor. Longer screws are avaiabe from your oca hardware store.
concrete/ceramic foors: 3/16 carbide-tipped masonry dri bit (Hammer may be needed for anchors.) 15/E, /2 and 3/8 combination wrench putty knife safety gasses tape measure or ruer channe ock Materias required: gas ine shutoff vave * /Z mae pipe thread for connection to pressure reguator - L.P. gas-resistant pipe-joint compound A.G.A. design-certified fexibe meta connector N-5 feet) or rigid gas suppy ine as needed Insuated pad or /4 pywood if range is instaed over carpeting screwdriver Eectrica Shock Hazard This appiance is equipped with a three-prong I grounding pug for your protection against shock hazard and shoud be pugged directy I into a propery grounded receptace. I Eectrica ground is required on this range. I Do Not ground to a gas pipe. I Do Not cut or remove the grounding prong 1 from this pug. If the pug wi not fit the I outet, have a proper outet instaed by a t quaified eectrician. I Do Not have a fuse in the neutra or! grounding circuit. A fuse in the neutra or! grounding circuit coud resut in an eectrica! shock. I Do Not use an extension cord with this range. ( Check with a quaified eectrician if you are I ot sure the range is propery grounded. I I,esut in death or serious injury. coud If codes permit and a separate grounding wire is used, it is recommended that a quaified eectrician determine that the grounding path is adequate. A 120-vot, 60-Hz, AC-ony, o-ampere, fused eectrica suppy is required. A time-deay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving ony this appiance be provided. Eectronic ignition systems operate within wide votage imits, but proper grounding and poarity are necessary. In addition to checking that the outet is correcty grounded, the outet must be checked by a quaified eectrician to see if it is wired with correct poarity. A wiring diagram is incuded on the back of the range. See Cabinet dimensions/requirements, Page 1, for recommended ocation of eectrica outet. Recommended grounding method For your persona safety, this range must be grounded. This range is manufactured with a power suppy cord having a 3-prong grounding pug. To minimize possibe shock hazard, the cord must be pugged into a mating, 3-prong, grounding-type, wa receptace, grounded in accordance with Nationa Eectrica Code, ANSI/NFPA 70 - atest edition* and a oca codes and ordinances. If a mating wa receptace is not avaiabe, it is the responsibiity and obigation of the customer to have a propery grounded, 3-prong, wa receptace instaed by a quaified eectrician. Copies of the standards isted may be obtained from: Nationa Fire Protection Association Batterymarch Park Quincy, Massachusetts 02269 t-prong groundingtype wa receptace B-prong grounding pug \ \ power suppy cord 4 Fire Hazard Range must be connected to a reguated gas suppy. Gas suppy must NOT exceed 1Cinch water coumn pressure. This must be checked by a quaified technician before instaing the range. Do Not use an open fame to test for eaks from gas connections. New A.G.A. design-certified fexibe gas ine shoud be used when oca codes permit. resut in a fire or injury. coud Observe a governing codes and ordinances. This instaation must conform with a oca codes and ordinances. In the absence of oca codes, instaation must conform with American Nationa Standard, Nationa Fue Gas Code ANSI 2223.1 - atest edition**. Input ratings shown on the mode/seria rating pate are for eevations up to 2,000 feet. For assistance when instaing the range at higher eevations, contact your oca service company. Type of gas: This range is factory set for use with Natura gas. It is design-certified by the American Gas Association IA.G.A.1 for Natura or L.P. gases with appropriate conversion. (See Gas conversions instructions, Pages 6-7.) The mode/seria rating pate (ocated on the frame behind the broier door) has information on the type of gas that can be used. If the type of gas isted does not agree with the type of gas avaiabe, check with the oca gas suppier. Conversion must be done by a quaified service technician. Gas suppy ine: Provide a gas suppy ine of 3/4 rigid pipe to the range ocation. With L.P. gas, piping or tubing size can be /2 minimum. A smaer size pipe on onger runs may resut in insufficient gas suppy. Usuay, L.P. gas suppiers determine the size and materias used in the system. Pipe-joint compounds made for use with L.P. gas must be used. Fexibe meta appiance connection: If oca codes permit, a new A.G.A. design-certified, /2 or 3/4 I.D., fexibe meta appiance connector is recommended for connecting range to the gas suppy ine. A /2 mae pipe thread is needed for connection to pressure reguator femae pipe threads. Do Not kink or damage the fexibe meta tubing when moving the range. an in-ine connection to the range. A strains must be removed from the suppy and fue ines so range wi be eve and in ine. manua shutoff vave Shutoff vave: The suppy ine must be equipped with a manua shutoff vave. This vave shoud be ocated in the same room as the range and shoud be in a ocation that aows ease of opening and cosing. The vave is for turning on or shutting off gas to the range. Do Not bock access to shutoff vave. Pressure reguator: The gas pressure reguator suppied with this range must be used. The inet pressure to the reguator shoud be as foows for proper operation: NATURAL GAS: Minimum pressure: 5 inches WCP Maximum pressure: 14 inches WCP L.P. GAS: Minimum pressure: 11 inches WCP Maximum pressure: 14 inches WCP Contact your oca gas suppier if you are not sure about the inet pressure. Line pressure testing above /2 psi gauge (14 WCP) -The range and its individua manua shutoff vave must be disconnected from the gas suppy piping system during any pressure testing of that system at test pressures equa to or greater than /2 psig (3.5 kpa1. Line pressure testing at /2 psi gauge (14 WCP) or ower -The range must be isoated from the gas suppy piping system by cosing its individua manua shutoff vave during any pressure testing of that system at test pressures equa to or ess than /2 psig (3.5 kpa). Copies of the standards isted may be obtained from: **American Gas Association 1515 Wison Bouevard Arington, Virginia 22209 Page 2
Check COO~~OP burners for Proper ffame Pug power!uppy cord mto grounded outet Make proper gas connection I- Remove shipping materia. Remove oven racks and parts package. Insta antitip bracket Repace or cose broier door Injury Hazard 8eCaUSe Of the weight and size of this range, two or more peope are required to move it. Do Not use hande for ifting. resut in injury, coud Put on safety gasses and goves. Do Not use oven door hande to ift or move the range, 2 Remove oven racks and parts package from inside oven. Remove shipping materias, tape and protective fim from range. cardboard shipping base Keep cardboard shipping base under range to prevent damage to foor covering. Contact a quaified foor covering instaer for the best procedure for driing mounting hoes thugh your type foor covering. Eectrica Shock Take specia care when driing hoes in the foor or wa. Eectrica wires may be behind the wa or foor covering and coud cause an eectrica shock if you touch them. Locate the eectrica circuits that coud be affected by the instaation of the anti-tip bracket and turn off power to these circuits. coud resut in death or serious injury. Injury Hazard To reduce the risk of tipping of the range, the range must be secured by a propery instaed foormounted anti-tip bracket, suppied with the range. Save these Instaation Instructions. Jf the range is moved to a new ocation, the anti-tip bracket must be removed and reinstaed in the new ocation. coud resut in injury. 4 Use the anti-tip bracket tempiwin.struction sheet to in&a the anti-tip bracket. Anti-tip bracket must be anchored securey to the sub foor.
Operating position front eveing eg Before moving range across foor, check that range is sti on cardboard shipping base to protect foor covering. 6 w Carefuy move range into fina operating position. Check that 8 n Pace rack in oven. Pace eve on rack, rear eveing eg is first side to side; then front to back. engaged in anti-tip bracket. If range is not eve, pu range forward unti rear eveing eg is removed from the anti-tip bracket. Use 3/8 drive ratchet and channe ock piers to adjust eveing egs up or down 5 n Remove cardboard shipping base unti range is eve. Push range back into under range. Open broier door. Use a 3/8 7 n If instaing the range in a mobie position. Check that rear eveing eg is drive ratchet to ower rear eveing egs one- home, you MUST secure the range to the foor. engaged in anti-tip bracket. haf turn. Use channe ock piers to ower front Any method of securing the range is adequate eveing egs one-haf turn. as ong as it conforms to the standards in the Note: Oven must be eve for satisfactory Mobie home instaation instructions, Page 1. baking conditions. Gas and eectrica connections 12 n f 4 I Use a brush and iquid detergent to test a gas connections. Bubbes around connections wi indicate a eak. If a eak appears, shut off gas vave contros and tighten connections. Then check connections again. Never test for gas eaks with a match or other fame. Cean a detergent from range. Repace broier door. Ah Fire Hazard 13 n Center the burner cap on burner Do Not make connection too tight. The Use 15/16 combination wrench and channe base. Burner cap shoud be eve when reguator is die cast. Making the ock piers to tighten fittings and fexibe propery positioned. Pace burner grates connection too tight may crack the connector. over burner. reguator, resuting in a gas eak and possibe exposion or fire. Do Not use an open fame to test for eaks 10 w Use pipe-joint compound made for 14 from gas connections. resut in a fire or exposion. coud use with L.P. gas to sea a gas connections. If fexibe connectors are used, be certain connectors are not kinked. w Pug power suppy cord into grounded eectrica outet. A connections must be wrench-tightened. Typica rigid pipe connection reguator shutoff vave in on position manua shutoff vave, open position union - H manua Typica fexibe connection 11 w Check that range reguator shutoff vave is in the on position. Open the manua shutoff vave in the gas suppy ine. Wait a few minutes for gas to move through the gas ine. pressure reguator adapter - i!# 5 manua /2 to 314 gas pipe maximum ength 21-112 gas - shutoff vave A /2 mae pipe thread is needed for connection to pressure reguator femae pipe threads. 9 n Assembe the fexibe connector from the gas suppy pipe to the pressure reguator.
Check operation Eectronic ignition system Cooktop and oven burners use eectronic ignitors in pace of standing piots. When a cooktop contro knob is turned to the LIGHT position, the system creates a spark to ight the burner. This sparking continues unti the contro knob is turned to the desired setting. When the oven contro is turned to the desired setting, a hot surface ignitor heats up bright orange and ignites the gas. No sparking occurs and the gow bar remains on whie the burner operates. Check operation of cooktop Push in and turn each surface unit contro knob to LIGHT position. The fame shoud ight within 4 seconds. Turn contro knob to HI position after burner ights. Do Not eave the knob in the LIGHT position after burner ights. Check each cooktop burner for proper fame. The sma inner cone shoud have a very distinct bue fame /4 to /2 ong. The outer cone is not as distinct as the inner cone. If the fame is noisy or bowing, it is getting too much air. II If the fame is soft and azy, it is not getting enough air. Turn surface burner contro knobs to OFF position. Adjust air shutter if needed. If surface burners need adjusting: 1. Remove contro knobs. Do Not use a meta bade to pry off contro knob; this coud damage the product. If the contro knob cannot be easiy removed, tuck a coth under the knob and pu out on the coth with steady, even pressure to remove the knob. 2.0pen oven door and remove 3 screws from bottom of manifod pane. Pu down sighty on manifod pane and pu pane away from range. 3. Using a fat-bade screwdriver, adjust the air shutter for each burner as needed. Cose the air shutter to decrease the amount of air to the fame. Open the air shutter to increase the amount of air to the fame. Adjust the air shutter to the widest opening that wi not cause the fame to ift or bow off of the burner. 4. Repeat the first part of Step 15 after adjusting the air shutters. 5. Repace manifod pane by tightening 3 screws in bottom of manifod pane. 6. Repace contro knobs on vave stems. Check operation of oven burner 16 n Open broier door. Foow the instructions for vour tvoe of oven contros. %Nrn OVEN HEATING 0 OFF. B Push in and turn the oven seector contro knob to 35O F. The oven burner shoud ight in 50-60 seconds; this deay is norma. The oven vave requires a certain time before it wi open and aow gas to fow. If your oven has eectronic contro pads ony: 1. Press the BAKE pad. The BAKE indicator wi ight. 350 wi appear in the dispay. The START? indicator wi begin to fash after 5 seconds. 2. Press the START/ENTER pad. The PREHEAT or HEAT, and ON indicators wi appear. The dispay wi show the automatic countdown time (10 minutes) needed to preheat the oven for seected temperature. The oven burner shoud ight in 50-60 seconds; this deay is norma. The oven vave requires a certain time before it wi open and aow gas to fow. The oven is preheated when the PREHEAT indicator ight goes off (consoe A ony), you hear a -second tone and the countdown changes to 350. * Note: PREHEAT indicator ight wi not be dispayed if oven temperature is over 170 F. D 1. Press the BAKE pad. The BAKE indicator wi ight. 350 F wi appear in the dispay. The START? indicator wi begin to fash after 5 seconds (consoe D ony). 2. Press the START/ENTER pad. PrE, and 1O:OO wi appear in the dispay HEAT and ON indicators wi ight. The oven is preheated when the time in the dispay counts down to O:OO, you hear a -second tone, and PrE changes to 350 F To avoid damaging the hot surface ignitor, do Not insert any object into the openings of the protective shied that surrounds the igniter or cean that area. n Check the oven burner for proper fame. The fame shoud be /2 ong, with inner cone of buishgreen, and outer mante of dark bue, andshoudbeceanandsoftin character. No yeow tips, bowing or shutoff vave air sh.btter and screw If oven fame needs adjusting: b Locate the air shutter next to the pressure reguator. Loosen screw and adjust the air shuttc unti the proper fame appears. Tighten screw. 18 n Turn the contro knob to OFF or press the OFF/CANCEL pad. Check operation of broi burner A 350 450 \,, 1 (TURN CfF OVEN VMEN FLAWING) OVEN HEATING 0 BROIL. B 450 400 Push in and turn the oven seector contro knob to BROIL. The broi burner shoud ight in 50-60 seconds; this deay is norma. The oven vav requires a certain time before it wi open and aow gas to fow.
Check operation (cont.) \ C 20 n Check that the broi burner is operating. 21 n Cose the broier door. Turn the oven contro knob to OFF or press the OFF/CANCEL pad. / A B 1. Press the CUSTOM BROIL pad. 525 or HI wi appear in the dispay. The BROIL indicator wi ight. The START? indicator wi begin to fash after 5 seconds. 2. Press the START/ENTER pad. HEAT (consoe B ony) and ON indicators wi ight. The oven burner shoud ight in 50-60 seconds; this deay is norma. The oven vave requires a certain time before it wi open and aow gas to fow. D 1. Press the CUSTOM BROIL pad. HI wi appear in the dispay. The BROIL indicator wi ight. *The START? indicator wi begin to fash after 5 seconds. 2. Press the START/ENTER pad. HEAT and ON indicators wi ight. The oven burner shoud ight in 50-60 seconds; this deay is norma, The oven vave requires a certain time before it wi open and aow gas to fow. You have just finished instaing your new range. To get the most efficient use from your range, read your Use & Care Guide. Keep Instaation Instructions and Guide cose to range for easy reference. The instructions wi make instaing the range in another home as easy as the first instaation. Gas conversions (from Natura gas to L.P. gas; or from L.P. gas to Natura gas) must be done by a quaified instaer. L.F? gas conversion 1 w Compete instaation sections A-C (Pages 3-4) before converting cooktop to L.P. gas. Check that main gas suppy ine has been shut off and the power suppy cord is disconnected. Fire Hazard Shut off gas suppy ine vave. Make a conversions before turning gas suppy vave back on. coud resut in exposion, fire or other injury. pressure ( U ieguator w Remove burner grates, caps and screws hoding burner bases to cooktop. Lift burners off cooktop. -cap- -washer - Nat. gas L.P. gas DO NOT REMOVE THE PRESSURE REGULATOR. 3 n Open broier door to ocate pressure reguator. Pressure reguator: Open pastic cover. Turn cap marked N on front of pressure reguator countercockwise with a wrench to remove. Do Not disturb or remove the spring beneath the cap. Remove pastic cover, Turn the cap over and reinsta pastic cover on top of cap. Insta cap on reguator so that the etters L.P. are visibe. Cose pastic cover over cap. Page 6
4 n Cooktop burners: Pu range out from Natura gas conversion orifice spuds countertop front about 4 inches. There are two cips, one on each side, ocated underneath the cooktop 2-3/8 inches back from the front of range. Carefuy side a putty knife in between the cooktop and the oven part of range. Whie genty ifting the cooktop, push in on the putty knife to reease the cip. Repeat on other side. I n Compete instaation sections A-C (Pages 3-4) before converting cooktop to natura gas. Check that main gas suppy ine has been shut off and the power suppy cord is disconnected. NAT L.P. etches gas manifod \ Remove and repace orifice orifice spuds Remove and repace orifice L.R. L.F. RF. RR. NAT L.P. etches gas manifod \ L.R. L.F. R.F. R.R. 5 H Prop open cooktop maintop. Remove the venturi pates. Locate L.P. gas orifice spuds in a iterature package incuded with the range. Orifice spuds are coor coded. Remove one n Remove burner grates, caps and screws hoding burner bases to cooktop. pressure reguator \ 5 w Cooktop burners: Prop open cooktop maintop. Remove the venturi pates. Locate Natura gas orifice spuds in iterature package. Orifice spuds are coor coded. Remove one L.P. gas orifice spud at a time using a 3/8 combination wrench. Insta the same coor Natura gas orifice spud to repace the L.P. gas orifice spud. Pace L.P. gas orifice spuds in pastic parts bag for future use and keep with iterature package. Reinsta venturi pates. Lower maintop to operating position and reinsta burner bases, screws, caps and burner grates. Natura gas orifice spud at a time using a 3/8 combination wrench. Insta the same coor L.P. gas orifice spud to repace the Natura gas orifice spud. Pace Natura gas orifice spuds in pastic parts bag for future use and keep with iterature package. Reinsta venturi pates. Lower maintop to operating position. Reinsta burner bases, screws, caps and burner grates. increase fame size pre-set at factory for Natura gas 6 n Oven burner: Use /2 combination wrench to turn the orifice hood down snug onto pin (approximatey 2 to 2-/2 turns). DO NOT OVERTIGHTEN. The burner fame cannot be propery adjusted if this conversion is not made. 7 n Compete instaation sections D through E, Pages 4-6. Check for proper fame. The sma inner cone shoud have a very distinct bue fame /4 to /2 ong. The outer cone is not as distinct as the inner cone. L.P. gas fames have a sighty yeow tip. If the fame is noisy or bowing, it is getting too much air. If the fame is soft and azy, it is not getting enough air. pressure reguator Nat. gas L.P. gas DO NOT REMOVE THE PRESSURE REGULATOR. 3 n Open broier door to ocate pressure reguator. Pressure reguator: Open pastic cover. Turn cap marked L.P. on front of pressure reguator countercockwise with a wrench to remove. Do Not disturb or remove the spring beneath the cap. Remove pastic cover, Turn the cap over and reinsta pastic cover on top of cap. Insta cap on reguator so that the etter N is visibe. Cose pastic cover over cap. 4 w Cooktop burners: Pu range out from countertop front about 4 inches. There are two cips, one on each side, ocated underneath the 2-318 cooktop 2-318 inches back from the front of range. * Carefuy side a putty knife in between the cooktop and the oven part of range. Whie genty ifting the cooktop, push in on the putty knife to reease the cip. Repeat on other side. pin / Natura gas increase gas increase fame size pm-set at factory for Natura gas 6 n Oven burner: Use /2 combination wrench to oosen the orifice hood away from pin (approximatey 2 to 2-/2 turns). The burner fame cannot be propery adjusted if this conversion is not made. 7 n Compete instaation sections D through E, Pages 4-6. Check for proper fame. Natura gas fames do not have yeow tips. I n Carefuy move range into fina operating position. Check that rear eveing eg is engaged in anti-tip bracket. I j n Carefuy move range into fina operating position. Check that rear eveing eg is engaged in anti-tip bracket. Page 7
If range does not operate: q Check that the circuit breaker is not tripped or the house fuse bown. q Check that the power suppy cord is pugged into the wa receptace. q Check that gas ine is turned on. q See Use and Care Guide for troubeshooting ist. If you need assistance: If you have questions about operating, ceaning or maintaining your range: q Refer to Use and Care Guide. q Ca the Consumer Assistance Center. Check your Use and Care Guide for a to-free number to ca or ca the deaer from whom you purchased this range. The deaer is isted in the Yeow Pages of your phone directory under Appiances - Househod - Major - Service and Repair. If you need service: Maintain the quaity buit into your range by caing an authorized service company. To obtain the name and number of an authorized service company: q Contact the deaer from whom you purchased your range; or q Look in the Yeow Pages of your teephone directory under Appiances - Househod - Major - Service and Repair; or q Ca the Consumer Assistance Center. The to-free number is isted in your Use and Care Guide. When you ca, you wi need: ij The range mode number. q The range seria number. Both numbers are isted on the mode/seria rating pate ocated on the frame behind the broier door. Part No. 3196322 Rev. A 0 1996 Moving the range: Injury Hazard Because of the weight and size of this range, two or more peope are required to move it. A ranges can tip. Do Not step, ean or sit on the range drawer or door. *The anti-tip device packed with range must be instaed. See Instaation Instructions. resut in injury. coud Benton Harbor, Michigan 49022 When moving range, side range onto cardboard or hardboard to prevent damaging the foor covering. If removing the range is necessary for ceaning or maintenance: 1. Shut off the gas suppy to the range. 2. Disconnect gas and eectrica suppies. If necessary, pu the range out, away from the wa, just far enough to disconnect the gas and eectric suppy ines. 3. Remove range to compete ceaning or maintenance. 4. Move range back into operating position. Look underneath range (a fashight may be needed) to check that eg is engaged in anti-tip bracket. If eg is not propery engaged, remove and reposition bracket to insure that eg fits propery in bracket. 5. Check that range is eve 6. Reconnect gas ine to range and check for eaks. 7. Pug power suppy cord into outet. Printed in U.S.A.