The CleanAIR CHEMICAL powered air purifying respirator protects you against particles as well as against gases and vapors, without breathing resistance. Compatible with standard threaded CleanAIR Rd40 filters and whole range of CleanAIR headpieces. High variability makes it suitable for use in many different applications. Chemical Flow Control Chemical Dual Flow Durable and powerful unit with two operating modes ECO (160 l/min) and TURBO (210l /min) The ECO mode gives the user lower but still sufficient air flow and prolongs the operating time. Air flow limit can be checked with included flow indicator. The TURBO mode is optimal for hard and long-term tasks in hot areas. Durable and powerful unit with two user modes MASK/ HOOD and three airflow levels for each of them. CleanAIR Chemical Flow Control is particularly safe, thanks to its intelligent warning system, which warns the user with a visual and accoustic signal when the smallest potential hazard such as a drained rechargeable battery, end of filter service life, increasing resistance or a drop in the air flow occurs. A rechargeable battery allows operation up to 10 hours. Intuitive control panel with well-arranged pictograms makes the unit user-friendly. Technical specification CA Chemical Dual Flow CA Chemical Flow Control Air flow: *160 l/min -140 l/min - ECO regime *200 l/min -180 l/min - TURBO regime * With fully charged battery and clean filters. ** Parameters depend on the chosen air flow level. 60,80,100 l/min - mode masks 120,140,160 l/min - mode hoods Weight: (incl. battery, w/o filters) 1050 g 1150 g Noisiness: max. 62 db max. 62 db Operating duration: **6,5-12 h **4-12 h Battery type: NiMH 6V/4,5Ah NiMH 7,2V/4,5Ah Certification: EN12941 TH1, EN12942 TM3 EN12941 TH2/TH3, EN12942 TM3
Belt Super Easily adjustable, secure and durable belt made of high quality materials is a basic accessory. Battery Exchangable NiMH battery, which can be charged on or off the unit. Canister type filters with thread RD40 acc. EN148-1. Approval acc. to EN14387 or EN143 makes filters suitable for full face masks and half masks without air supply system. When used with CA Chemical unit it is necessary to have 3 filters of the same type. Particle Filter Type: P3 Diameter/height: 110 mm/50 mm, Weight: 83 g Area of application: dust particles, solid and liquid aerosols, toxic smoke Certification: EN 12941, EN 12942, EN 143 Gas Filters Type: A2 Diameter/height: 110 mm/78 mm Weight: 225 g Area of application: organic gases and vapours with a boiling point above 65 C Certification: EN 12941, EN 12942, EN 14387 Combined filters Type: A2P3 Diameter/height: 110 mm/95 mm Weight: 275 g Area of application: as A2 filter + against dust particles, solid and liquid aerosols, toxic smoke Certification: EN 12941, EN 12942, EN 14387 Type: A2B2E2K2P3 Diameter/height: 110 mm/95 mm Weight: 360 g Area of application: as A2B2E2K2 filter + against dust particles, solid and liquid aerosols, toxic smoke Certification: EN 12941, EN 12942, EN 14387 Type: A2B2E2K2HgPSL Combined filter for specific use against mercury vapours Certification: EN 12941, EN 12942, EN 14387 Useful accessories prefilter prefilter keeper
The CleanAIR PRESSURE provides a conceptual solution for workplaces with the availability of compressed air supply from the distribution system, mobile air source, or a compressor. The supplied airline system can be used in combination with whole range of CleanAIR headpieces for various industrial applications, which require an air supply that is independent from the ambient air. Without breathing resistance, it provides protection in particular for long duration applications. An adjustment valve on the belt unit enables the user to regulate the air flow between 170 and 400 l/min and therefore adapt the air flow to workers individual needs. The CleanAIR PRESSURE is characterized with low noise level and light weight, enabling the user to work safely for long periods, while benefiting from excellent comfort. The modular supplied air system CleanAIR PRESSURE provides comfortable and reliable respiratory protection in accordance with EN 14594:2005. CA Pressure Flow Control In addition, the Flow Control version is equipped with a checking pressure gauge for continuous control of the respiratory system. CA Pressure The main component, inner pressure control valve, ensures the supply of constant air flow into the head-piece (the inlet pressure has to be between 0,4 1 Mpa). The unit is equipped with an adjusting knob for regulation of the air flow. A very efficient sound absorber reduces the noisiness. Technical specification CA Pressure CA Pressure Flow control Air flow - adjustable: min. 170 l/min, max. > 400 l/min min. 170 l/min, max. > 400 l/min Weight: 200 g 250 g Noisiness: max. 61 db max. 61 db Filter efficiency: *P3 *P3 Certification: EN 14594:05 2A EN 14594:05 2A * in use with Clean-air Pressure Conditioner
CA Pressure Conditioner A filter station is available for improving the quality of the inhaled air. The device is made of a strong metal container with high capacity combined filter inside. This filter station removes particles, adhesions like oil mists and unpleasant odours from industrial compressed air and therefore substantially improves the quality of the inhaled air. The inlet quick coupling allows a single-handed assemble of the device, outlet piece is prepared to connect up to 2 workers with CA Pressure unit. Checking pressure gauge measures the outlet pressure. Weight: Dimensions (height / diameter): Min. inlet pressure: Max. inlet pressure: Connectors: 6,80 Kg 380 / 200 mm 0,3MPa 1 MPa Quick couplings Standard compatible with Rectus and Ceyn 320, 1x inlet, 2x outlet Structure: particle filtr Combined filter Activated carbon Weight: 500 g Dimensions (height, diameter): 19,5 x 11 cm Hoses for pressured air Linking hoses between CA Pressure and CA Pressure Conditioner. spiral hose Lenght: 10 m Pressure: max 2MPa Weight: 600g standard hose Lenght: 10 m Pressure: max 2MPa Weight: 2 100g Connection scheme Compressed air supply CA Pressure Conditioner Linking hose CA Pressure unit with belt Headpiece with hose
The CleanAIR BASIC 2000 powered air purifying respirator is designed specially for particle filtration [dust, non-toxic and toxic fumes, solid and liquid aerosols, backteria and viruses]. Compatible with whole range of CleanAIR headpieces, it can be used in a wide range of applications. Without breathing resistance, it provides protection in particular for long duration applications. The CleanAIR BASIC 2000 powered air purifying respirator combines ergonomic design, a high level of wearer comfort and extremely low weight. All of the technology and features you need. Basic 2000 Flow Control Basic 2000 Dual Flow With two operating modes ECO (160 l/min) and TURBO (210 l /min) The ECO mode gives the user lower but still sufficient air flow and prolongs the operating time. Air flow limit can be checked with included flow indicator. The TURBO mode is optimal for hard and long-term tasks in hot areas. With intelligent warning system which warns the user with a visual and acoustic signal when even the smallest potential hazard such as a drained rechargeable battery, end of filter service life, increasing resistance or a drop in the air flow occurs. The rechargeable battery ensures operations for up to 10 hours. Intuitive control panel with well-arranged pictograms makes the unit user-friendly. Technical specification: CA Basic 2000 Dual Flow CA Basic Flow Control Initial flow rate: *160 l/min - 140 l/min - regime ECO 140-210 l/min Final flow rate: *200 l/min - 180 l/min - regime TURBO (8 optional levels) Weight (incl.filter and battery): 900 g 900 g Filter type PSL PSL Filter efficiency: 99,998% 99,998% Noisiness: max. 61 db max. 61 db Operating duration: **6-9 h **6-10 h Certification: EN 12 941 TH1 PSL EN 12 941 TH2/TH3 PSL * With fully charged battery and clean filters. ** Parameters depend on the chosen air flow level.
CleanAIR Basic filter A particle filter P3, that provides protection against all types of particles (dust particles, solid and liquid aerosols, toxic smoke) The filter separates no less than 99,9998% of the air pollution. Belt Standard Easily adjustable, secure and durable belt made of high quality materials is a basic accessory. Certification: EN 12941, type PSL Temperature range for storage and service: 0 C to + 40 C Dimensions: (diameter / height): 132 / 55 mm Weight: 100 g CleanAIR Basic prefilter Prefilter Odour filter Belt Super Option for users, who like more comfort and increased back support. It prolongs the life time of the main filter. Is made of 100% PES suitable for all filtration, protects the filter against premature clogging by larger particles. Can be easily fastened around a particle filter by sticky tapes which are ready for use on both sides of the prefilter. Odour filter Removes unpleasant odours and thus provides additional comfort Basic 2000 Filter Cover Battery Exchangable NiMH battery, which can be charged on or off the unit. Battery
High efficiency breathing protection CA Asbest unit CA Asbest unit attached directly to the full face mask. CA Asbest unit CA Asbest unit worn on the belt and connected to the mask by a hose
Unit Extra lightweight and compact powered respiratory device originally developed for workers manipulating with asbestos. The complete set with the fullfacemask and a high efficiency particle filter meets professional requirements like: TM3 protection, sufficient airflow level, decontamination feasible by water shower. Filter It delivers the stream of air into the fullface mask and thus reduces the breathing resistance which is particulary welcome for users who need to wear a mask for longer period. Compact design of the unit allows shower decontamination. Our unit is powered by an exchangable Li-ion battery which runs for more than 5 hours and can be recharged in less than 5 hours. The whole systém is easy to clean and maintain. A particle filter is able to separate toxic / non-toxic particles and solid / liquid aerosols with P3 level efficiency. Protective Fullface mask It has an ergonomical design and for wearer comfort is made of silicon rubber. Is equipped with 2 exhalation valves and a panoramatic visor. 5 straps ensures good fit to the face. Unit positioning Directly to the fullface mask Carried on a rubber belt and connected to the mask via a hose Technical data: Flow rate, minimum: 160 l/min Weight incl. filter and battery: 385 g Filter: type filter efficiency PSL min. 99,998 % (corresponding with P3 class) Battery: type lifetime Li-Ion 7,2V/2,20Ah 500 charging cycles Operating duration: 5 hours Ingress Protection (IP): IP65 Classification: EN 12 942 TM3 PSL Nominal protective factor: 2000
Increasing demand on personal protection brings the need of effective breathing protection during welding. A perfect solution is to use a respiratory device which delivers a stream of clean air into the welding hood. The created overpressure prevents harmfull substances to enter into the head piece. Our system is effective, comfortable and does not increase the breathing resistance. Welding hood with integrated breathing protection CA-22 Stable, comfortable, well-balanced Two stages flip-up window Thickened rim around the visor increases the heat insulation For autodarkening filters or fixed welding filters (110 / 90 mm) Flip-up window allows grinding, checking and other operations User friendly system of exchanging the welding filter Integrated breathing protection: face seal, sweatbands and airduct EN 175 B Welding hood with integrated breathing protection CA-25 Well-balanced and lightweight, comfortable and durable headgear Increased heat insulation For autodarkening filters (110 / 90 mm) User friendly system of exchanging the welding filter Simple replacement of protective plates without removal of the ADF Integrated breathing protection: face seal, sweatbands and airduct EN 175 S Welding hood with integrated breathing protection CA-26 CleanAIR respiratory systems for welding hoods CA Basic protection against particles CA Chemical protection against particles, gases and their combinations CA Pressure protection against complete spectrum of contaminants Well-balanced and lightweight Large viewing angle, optimum protection of the face, ears and throat For autodarkening filters (110 / 90 mm) Simple replacement of protective plates without removal of the ADF Integrated breathing protection: face seal, sweatbands and airduct EN 175 S
Autodarkening filters They switch to the dark automatically at the strike of an arc and return to the clear state after welding is complete. Usage of an autodarkening filter minimises the need of manipulation with a welding hood. Filters are powered by solar cells in combination with the built in battery. All filters are manufactured according to DIN and EN standards. Technical parametres F11 V9-13 DS V6-13 GDS Standard EN 379 EN 379 EN 379 Optical classes 1/2/1 1/1/1/2 1/1/1/2 Viewing area 95 x 46.5mm 95 x 46.5mm 95 x 46.5mm Dimension 110x90 mm 110x90 mm 110x90 mm Weight 75g 95g 115g open state shade 3 4 4 closed state shade 11 9-13 6-8 / 9-13 shade adjustment fixed Yes / built in knob Yes / external knob sensitivity adjustment Fixed Yes / built in knob Yes / built in knob delay adjustment No Yes / built in knob Yes / external knob grinding mode No No Yes / built in knob switching time at +23 C 0.0005s 0,00015s 0,00015s clearing time 0.2s 0,2 0,8s 0,2 0,8s UV/IR protection UV15 / IR14 UV15 / IR14 UV15 / IR14 temperature range -10` C / +60 C -10` C / +60 C -10` C / +60 C TIG detection optimized enhanced enhanced energy supply Solar cells Solar cells Solar cells ADC angular dependence NO YES YES compensation Useful accessories Neck protection for all types of welding hoods Head protection for all types of welding hoods Tyvek Inner protective hood Protective folios inner and outer Welding lens size 110 / 90 shade 9 to 13
Our broad offer of headpieces gives the CleanAIR respiratory system its versatility and utilizability in a wide spectrum of applications. From food processing and pharmaceutical industries, through agriculture up to chemical and heavy industries. Light hood CA-1 Extremely light, universal size, for long wearing periods Good fitting elastic bands ensure good wearing comfort Air stream delivered through supply hose, flown over the crown of the head to the breathing zone Air ventilation, expiratory valve and special antifog treatment prevents visor from misting Offers wide undisturbed view Colours: orange / grey Weight: 120 g Universal hood CA-2 Lightweight hood, universal size, for long wearing periods Good fitting elastic bands ensure good wearing comfort Prolonged protective hood covering neck and shoulders Air stream delivered through supply hose, flown over the crown of the head to the breathing zone Air ventilation, expiratory valve and special antifog treatment prevents visor from misting Offers wide undisturbed view Colours: orange / grey Weight: 160 g Universal hood CA-10 All benefits of CA-2 hood In combination with powered respiratory unit (version Flow Control) and with special hose, offers the highest protection factor NPF 500. Colours: white Weight: 160 g Full face mask CA-6 Made of silicon rubber highest wearing comfort Easily exchangable panoramic glass-polycarbonate visor 5 elastic straps for secure wearing Threaded connector RD40 x 1/7 (EN 148-1) Easily decontaminable Weight: 500 g Filtering device / Headpiece CA-1 CA-2 CA-10 CA-6 Classification acc. to EN 12941 CA Basic Dual Flow / Flow Control TH1 / TH2 TH1 / TH2 - / TH3 - / - CA Chemical Dual Flow / Flow Control TH1 / TH2 TH1 / TH2 - / TH3 TM3 Classification acc. to EN 14594:05 CA Pressure 2A 2A 2A - CA Pressure Flow Control 2A 2A 2A - Classification acc. to EN 12942 CA Chemical Flow Control - - - TM3 CA Asbest - - - TM3
Grinding visor CA-3 Respiratory and eye protection (EN 166) Adjustable head harness ensures optimal fit Textile head cover available Supplied air is delivered by an airduct to a breathing zone Face seal colours: orange, grey Weight: 480 g Safety helmet CA-4 All advantages of CA-3 visor Protective system 4 in 1 An additional visor and ear muffs for hearing protection Face seal colours: orange, grey Weight: 680 g without ear muffs Welding hood with integrated breathing protection CA-22 Stable, comfortable, well-balanced Two stages flip-up window Thickened rim around the visor increases the heat insulation For autodarkening filters or fixed welding filters (110 / 90 cm) Flip-up window allows grinding, checking and other operations User friendly system of exchanging the welding filter Integrated breathing protection: face seal, sweatbands and airduct EN 175 B Welding hood with integrated breathing protection CA-25 Well-balanced and lightweight, comfortable and durable headgear Increased heat insulation For autodarkening filters (110 / 90 cm) User friendly system of exchanging the welding filter Simple replacement of protective plates without removal of the ADF Integrated breathing protection: face seal, sweatbands and airduct EN 175 S Welding hood with integrated breathing protection CA-26 Well-balanced and lightweight Large viewing angle, optimum protection of the face, ears and throat For autodarkening filters (110 / 90 cm) Simple replacement of protective plates without removal of the ADF Integrated breathing protection: face seal, sweatbands and airduct EN 175 S Filtering device / Headpiece CA-3 CA-4 CA-22 CA-25 CA-26 Classification acc. to EN 12941 CA Basic Dual Flow / Flow Control TH1 / TH2 TH1 / TH2 TH1 / TH2 TH1 / TH2 TH1 / TH2 CA Chemical Dual Flow / Flow Control TH1 / TH2 TH1 / TH2 TH1 / TH2 TH1 / TH2 TH1 / TH2 Classification acc. to EN 14594:05 CA Pressure 2A 2A 2A 2A 2A CA Pressure Flow Control 2A 2A 2A 2A 2A
Canister type filters with thread Rd40x1/7. Approval acc. to EN14387 or EN143 makes our filters suitable for full face masks and half masks without air supply system. When used with CA Chemical unit it is necessary to have 3 filters of the same type. Particle Filter Type: P3 Area of application: dust particles, solid and liquid aerosols, toxic smoke Certification: EN143, EN 12941, EN 12942 Diameter / Height / Weight: 110mm/50mm/83g Gas Filters Type: A2 Area of application: organic gases, vapours with a boiling point above 65 C Certification: EN14387, EN 12941, EN 12942. Diameter / Height / Weight: 110mm/78mm/225g Type: B2 Area of application: inorganic gases, vapours Certification: EN14387, EN 12941, EN 12942. Diameter / Height / Weight: 110mm/78mm/225g Type: E2 Area of application: acid gases and vapours Certification: EN14387, EN 12941, EN 12942. Diameter / Height / Weight: 110mm/78mm/225g Type: K2 Area of application: ammonia, amines and organic ammonia derivates Certification: EN14387, EN 12941, EN 12942. Diameter / Height / Weight: 110mm/78mm/225g Type: A2B2 Area of application: organic gases, vapours with a boiling point above 65 C, inorganic gases, vapours Certification: EN14387, EN 12941, EN 12942. Diameter / Height / Weight: 110mm/78mm/312g Type: A2B2E2 Area of application: organic gases, vapours with a boiling point above 65 C, inorganic and acid gases or vapours (sulphur dioxide) Certification: EN14387, EN 12941, EN 12942. Diameter / Height / Weight: 110mm/78mm/312g Type: A2B2E2K2 Area of application: organic gases, vapours with a boiling point above 65 C, inorganic and acid gases or vapours (sulphur dioxide), ammonia and organic amonia Certification: EN14387, EN 12941, EN 12942. Diameter / Height / Weight: 110mm/78mm/312g
Combined filters Type: A2P3 Area of application: organic gases, vapours with a boiling point above 65 C + dust particles, solid and liquid aerosols, toxic smoke Certification: EN 14387, EN 12941, EN 12942 Diameter / Height / Weight: 110mm/95mm/275g Type: B2P3 Area of application: inorganic gases, vapours + dust particles, solid and liquid aerosols, toxic smoke Certification: EN 14387, EN 12941, EN 12942 Diameter / Height / Weight: 110mm/95mm/275g Type: K2P3 Area of application: ammonia, amines and organic ammonia derivates + dust particles, solid and liquid aerosols, toxic smoke Certification: EN 14387, EN 12941,EN12942 Diameter / Height / Weight: 110mm/95mm/275g Type: A2B2E2K2P3 Area of application: as A2B2E2K2 + dust particles, solid and liquid aerosols, toxic smoke Certification: EN14387, EN 12941, EN 12942 Diameter / Height / Weight: 110mm/95mm/360g Type: A2B2E2K2HgP3 Area of application: as A2B2E2K2P3 + mercury vapors and compounds Certification: EN14387, EN 12941, EN 12942 Diameter / Height / Weight: 110mm/95mm/360g OZONE - WELDING FILTER Type: A2B2E2SXP3 Colour type: Certification: EN14387, EN 12941, EN 12942 Area of application: Special welding and cutting applications (TIG welding, plasma arc and lasser cutting) organic gases, vapours with a boiling point above 65 C, inorganic gases or vapours + dust particles, solid and liquid aerosols, toxic smoke + OZON Other combinations on request