OBSOLETE DESIGN DATA. CONCENTRATE CONTROLLERS 2, 3", 4", 6" and 8" (50, 80, 100, 150, and 200 mm)

Similar documents
FM Approved - Automatic Water Control Valve as standard deluge valve. No formal approval available for coating. Foam Concentrate

FM Approved - Automatic Water Control Valve as standard deluge valve. No formal approval available for coating. Foam Concentrate

TECHNICAL DATA NOTICE

Wet pipe low flow foam/water system

OBSOLETE. Wet pipe low flow manifold system

LINE PROPORTIONERS LP NPR260 Approvals: UL, ULC

TECHNICAL DATA. the Viking Pilot Pressure Regulating Valve 1 Model A-1 Speed Control Assembly: OBSOLETE. the Viking Speed Control Assembly 1

OBSOLETE DESIGN DATA FOAM MAKER APPLICATION

Foam Mixers & Proportioning Systems

Pipe Thread Connection 1/2 inch NPT. Friction Loss Refer to Figure 3

TECHNICAL DATA OBSOLETE

TECHNICAL DATA Q= C. Table 1 - Specifications

TECHNICAL DATA. than the water inlet pressure to the concentrate

Data Sheet Issue A

TECHNICAL DATA. Pressure Regulation 531a. April 24, 2009

TECHNICAL DATA. Page 1 of 12

Anti-flood device Model B-1

VERTICAL BLADDER TANK

Speed control assembly model A-1

TECHNICAL DATA. Deluge Valves 211a. November 30, 2007 DELUGE VALVE MODEL E-1 ANGLE STYLE 3 (DN80), 4 (DN100) & 6 (DN150)

HORIZONTAL BLADDER TANK

TECHNICAL DATA ANTI-FLOOD DEVICE MODEL B-1 1. DESCRIPTION

End Connection. Thread x Thread N/A N/A N/A N/A Flange x Flange N/A

SEMI FIXED/PORTABLE LINE PROPORTIONERS SLP NPR270

TECHNICAL DATA. Table 1 - Specifications

TECHNICAL DATA. Low-Flow Foam Preaction System with Hydraulically Actuated Concentrate Control Valve.

DESIGN DATA OBSOLETE. C. Inspections - It is imperative that the system be inspected and tested on a regular basis. See Inspection

TECHNICAL DATA. Q = C v P S

MANUAL FLOW CONTROL 2-1/2" - 18" QUICKSET FLOW CHART

SABERINDO PACIF SABERINDO PACIFIC CIFIC SABERINDO PA. A Tyco International Company

TECHNICAL DATA. Trimpac 244a. September 16, 2013

TECHNICAL DATA. Q = C v P S

Model DDX-LP Dry Pipe Valve System 8 (200mm) Features. Differential latching clapper-type, lighweight, dependable construction.

Features. Model DDX-LP Dry Pipe Valve System 4 (100mm), 6 (150mm) & 165mm Sizes

TECHNICAL DATA. Q = C v P S

DESIGN DATA A WET PIPE BLADDER TANK FOAM/WATER SYSTEM WITH HYDRAULICALLY ACTUATED DELUGE CONCENTRATE CONTROL VALVE

TECHNICAL DATA OBSOLETE

TECHNICAL DATA. Q = C v P S

Gauge Adapters. Senior 2 1 2" [63,5] Bolt Circle Adapt ers. 22 Series ISO 9001:2008 CERTIFIED. Low pressure applications. The Measure of Excellence

TECHNICAL DATA. Dry 132a. October 1, 2008

TECHNICAL DATA CAUTION

OBSOLETE DESIGN DATA. Foam 301a. February 9, 1998

TECHNICAL DATA. Q = C v P S

TECHNICAL DATA. Deluge Valves 218a. November 30, 2007 DELUGE VALVE MODEL F-1 STRAIGHT THROUGH STYLE 2-1/2 (DN65) - 8 (DN200)

TECHNICAL DATA. Trimpac 251a. Spetember 16, 2013

TECHNICAL DATA. Trimpac 256a. October 31, 2013

DAV - WP DAV - WP. Wastewater Air Valves. Product Catalogue. (Wastewater Air Valves) DAV - WP

TECHNICAL DATA OBSOLETE

Air Eliminators and Combination Air Eliminators Strainers

Balancing HVAC Hydronic Systems Part 3: Flow Measurement Valves

Horizontal Bladder Tanks

Model B-1 Pipe Line Strainer 3, 4, 6 & 8 Inch (DN80, DN100, DN150 & DN200) 175 psi (12,1 bar) General Description. Technical Data

AIR FOAM CHAMBER DATA SHEET

Model MTB-ASME Horizontal Bladder Tanks

TECHNICAL DATA. TRIMPAC Model B-5 & B-5B

TECHNICAL DATA PILOT PRESSURE REGULATED DELUGE SYSTEM CONTROLLED BY PNEUMATIC RELEASE. 1. DESCRIPTION (Refer to Figures 1, 2 or 3.

Vertical Bladder Tanks

HighVac Pumps. High Vacuum Venturi Pumps. Modular Venturi Vacuum Pumps with Solenoid-Operated Vacuum and Blow-Off

TECHNICAL DATA. Trimpac 257a. September 16, 2013

TECHNICAL DATA 3 MODEL G-3000 DRY VALVE RISER ASSEMBLY

TECHNICAL DATA. Page 1 of 8. model f /2 (dn40) & 2 (dn50)

Pressure booster. Air Service Units Series Page. General 5.1. Pressure boosters ø Pressure boosters ø 40 c/w air pressure regulator 5.

TECHNICAL DATA OBSOLETE

Foam Systems. Fire Protection Solutions

ECS Protector Nitrogen Inerting Vent (PAV-WN)

TECHNICAL DATA. Notes: For use with Trim Charts on Pages 2-4

TECHNICAL DATA PILOT PRESSURE REGULATED DELUGE SYSTEM CONTROLLED BY ELECTRIC RELEASE 1. DESCRIPTION 2. LISTINGS AND APPROVALS 3.

TECHNICAL DATA. Q = C v P S

XDF BURNERS DUAL FUEL EXCESS AIR BURNER FEATURES DESCRIPTION EXCESS AIR OPERATION

TECHNICAL DATA MAINTENANCE AIR COMPRESSOR MODEL G-1

Propor tional Re lief Valve s

TECHNICAL DATA Q = C. v P S. 2 Model G-2000 Dry valve. Page 1 of 13

MLS Series Liquid Level Switches. Installation and Operations Manual Section 15

TECHNICAL DATA. Q= Cv S

Vertical and Horizontal Bladder Tanks

FOAM TANK (1/2) DATA SHEET

TECHNICAL DATA SINGLE INTERLOCKED PREACTION SYSTEM WITH PNEUMATIC RELEASE

MEGR-1627 Instruction Manual

Model MTB-ASME Vertical Bladder Tanks

ALF400 to 900, ALT-5/-9

TECHNICAL DATA. Inlet Type Outlet Type OBSOLETE. 4. TECHNICAL DATA Approvals:

Model MTB-ASME Vertical Bladder Tanks

Flow Material Length. Weight GPM LPM. Style 3095

Pro-V Multivariable Flowmeter Model M22 In-line Vortex

SELECTION GUIDE SELECTION GUIDE. Pressure, Flow, Level & Temperature Products for Ultra-Clean Processing P R E C I S I O N S E N S O R S

CASH VALVE TYPE KP BACK PRESSURE VALVES

Foam Chamber Model-FC

Installation Operation Maintenance

Wastewater combination air valve in stainless steel AISI 316 Mod. SCS

Auto Feed Lube, Auto Feed Tank ALF400 to 900, ALT-5/-9

Mass Flow Controllers

1805 Series Relief Valves

KECKLEY INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS TYPE NO. 7 FLOAT VALVE

Bladder Tank Installation & System Design Information

GAS PRESSURE REGULATORS AP

LAKOS Waterworks. PWC Series Sand Separators. Installation & Operation Manual LS-829 (10/12)

pvc well casing & drop pipe

TECHNICAL DATA DELUGE VALVE, MODEL F-1 STRAIGHT THROUGH STYLE

UBEC 1AT. AUTO TANK Fill System Installation, Operation, & Setup Instructions

General. Rugged, Reliable with Value-added Features. Pipe Sizes. Temperature Limits. Spring Ranges. Buried Service. Increased Outlet Pipe Sizes

Transcription:

March 1, 2001 Foam 210 a 1. PRO DUCT NAME Viking Concentrate Controller 2,, (102 mm) (152 mm), (203 mm) Available since 1996. 2. MANUFACTURED FOR THE VIKING COR PO RA TION 210 North Industrial Park Road Hastings, MI 49058 U.S.A. Telephone: (616) 945-9501 (877) 384-5464 Fax: (616) 945-9599 e-mail: techsvcs @vikingcorp.com 3. PRO DUCT DE SCRIP TION The Viking concentrate controllers accurately proportion foam con cen - trate into a water stream over a wide range of wa ter flow rates. The con - trollers proportion foam at con cen - trations from 1% to 3 %. 4. TECHNICAL DATA The Viking concentrate controllers are tested as part of a fire ex tin guish - ing system and are UL Listed and FM Approved for use with designated foam concentrates, bladder tanks, piping configurations and discharge devices. 5. OP ER A TION The Vi king concentrate controller is a modified venturi device. As water flows through the venturi, it creates an area of lower pressure referred to as the metering pressure drop. As the water flow increases through the venturi, the metering pressure drop increases, allowing more foam con - centrate to enter through the orifice. A decrease in the wa ter flow reduces the metering pressure drop, thereby reducing the foam concentrate flow. Because the foam concentrate flow varies in direct proportion to the wa - ter flow, the concentrate controller can accurately proportion foam over a wide range of wa ter flow rates. The flow rate at which the metering pressure drop is just high enough to overcome the pressure losses through the piping and the bladder tank is called the low flow rating. The flow rate through the controller must Form No. F_041497 DESIGN DATA be at or above it s low flow rating in order to properly proportion foam. A good rule to follow to ensure the piping is designed properly follows: The combined total equivalent length (pipe length plus equivalent lengths for fittings and valves) of the water supply inlet piping and the foam concentrate discharge piping should not exceed 50 equivalent feet (15,2 m). The diameter of this piping must be the same size as the foam liquid inlet to the concentrate con trol - ler. If the total equivalent length must exceed 50 feet (15,2 m), then re fer to the Proportioning Device Design data located in the Design section of this data book for the method of calculating these pipe sizes. 6. AP PLI CA TION The Vi king concentrate controllers are part of a foam system. In addition to the controller, the main com po - nents of the foam sys tem are foam concentrate, a foam stor age tank, a water supply, piping, and discharge devices. The discharge devices most commonly used are sprin klers, nozzles, and foam chambers. The system must be designed so that the concentrate controller can ac cu - rately proportion foam over the range of flow rates expected during the sys tem operation. 7. AVAILABILITY AND SERVICE The Vi king concentrate controllers are available through a network of domestic, Canadian and in ter na - tional dis trib u tors. See the Yellow Pages of the telephone directory for a local distributor (listed under Sprin- kler-automatic-fire ), or contact The Viking Corporation. Vi king tech ni cal data may be found on The Vi king Cor po ra tion s Web site at http :// www.vikingcorp.com. The Web site may in clude a more recent edi tion of this tech ni cal data page. 8. GUAR AN TEES For details of warranty, re fer to Vi - king s current list price schedule or contact Viking directly. CONTROLLERS 2,,, and (50, 80, 100, 150, and 200 mm) 9. IN STAL LA TION DO NOT ALTER THE PIPING WITH - OUT CONSULTING A SYSTEM DESIGN REPRESENTATIVE. BE - FORE INSTALLING A CON CEN - TRATE CONTROLLER, CHECK THE SYSTEM DESIGN DRAWING TO EN - SURE THE CONTROLLER LO CA - TION DOES NOT CREATE EX CES - SIVE HEAD PRESSURE OR FRIC - TIONAL LOSSES. The controller must be installed with the ar row pointing in the direction of the wa ter flow. Straight piping equal to four (4) to six (6) pipe diameters should be installed both before and after the concentrate controller to en - sure proportioning accuracy. The ideal location for the controller is level or below the top discharge and within 3 feet (1 m) of the tank. The controller can be placed further from the tank, if the pressure drop through the blad der tank does not exceed the metering pressure drop. The pres - sure drop within the piping can be minimized by: 1. Minimizing the number of tees and elbows. 2. Minimizing the distance from the bladder tank to the controller, using full port valves. 3. Increasing the pipe diameter. Viking strongly advises the in stal la - tion of a concentrate control valve, and swing check valve between the bladder tank and concentrate con - troller. This will prevent migration of water into the bladder tank. Viking does not furnish piping with the concentrate controllers. It is the responsibility of the system design engineer to determine the ap pro pri - ate piping. 10. INSPECTIONS AND TESTS Refer to the applicable Viking foam system technical data pages for in - structions on inspections and test ing of the complete foam system. 11. MAIN TE NANCE Refer to the applicable Viking foam system technical data pages for in - structions on maintenance of the complete system. Replaces page 860 a-f, dated March 25, 1999. Re - placed 3M reference with National Foam, added drawings and revised page number.

210 b March 1, 2001 CON TROL LERS 2 Threaded Concentrate Controller SIZE A B C D E F G WEIGHT Threaded Grooved 2 7/ (73) 3 3/1 (81,0 mm) 3 31/3 (101,2 mm) 4 1/ (114,3 mm) 9" (228,6 mm) 9" (228,6 mm) 6 1/ (165,1 mm) 6 1/ (165,1 mm) 10" (254 mm) 10" (254 mm) 12 3/ (323,9 mm) 12 3/ (323,9 mm) 13 1/ (342,9 mm) 13 1/ (342,9 mm) 3 1/ (79,4 mm) 3 1/ (79,4 mm) (76,2 mm) (76,2 mm) 3 1/ (88,9 mm) (101,6 mm) 4 5/ (117,5 mm) 6 3/ (161,9 mm) 1" (25,4 mm) 1" (25,4 mm) 1 1/ (32 mm) 1 1/ (38,1 mm) 1 1/ (38,1 mm) 2 1/ (63,5 mm) 2 1/ (63,5 mm) x 7 1/ (76 mm x 190 mm) x 7 1/ (76 mm x 190 mm) x 9" (102 mm x 228 mm) x 9" (102 mm x 228 mm) x 11" (152 mm x 297 mm) x 11" (152 mm x 297 mm) x 13 1/ (203 mm x 343 mm) x 13 1/ (203 mm x 343 mm) 2 Grooved Concentrate Controller 2 1/ (57,1 mm) 2 1/ (57,1 mm) 1 1/ (38,1 mm) (76,2 mm) 3 23/6 (59,9 mm) 3 1/1 (77,8 mm) 2 1/ (63,5 mm) 3 1/ (88,9 mm) 5 lbs. (2.3 kg.) 5 lbs. (2.3 kg.) 12 lbs. (5.4 kg.) 23 lbs. (10.4 kg.) 19 lbs. (8,6 kg.) 35 lbs. (15.9 kg.) 34 lbs. (15.4 kg.) 55 lbs. (25 kg.) 54 lbs. (24 kg.) 85 lbs. (38.6 kg.) Dimensions in parentheses are metric and may vary from actual.

March 1, 2001 CON TROL LERS 210 c 6 Style Concentrate Controller (3, 4 & 8 also available) 6 Style Concentrate Controller (3, 4 & 8 also available)

210 d March 1, 2001 DESIGN DATA CONTROLLERS 2,,, and (50, 80, 100, 150, and 200 mm) BLADDER TANK AND CONTROLLER PERFORMANCE Controller Size Threaded 1" NPT Grooved 1" NPT 1-1/ NPT 1-1/ NPT 1-1/ NPT NPT NPT 2-1/ NPT 2-1/ NPT NPT Viking Concentrate National Viking Part No. Viking Controller Model No. Orifice dia. Min. Flow Max. Flow Inch (mm) gpm (L/m) gpm (L/m) VF1NWAFFF Aer-o-Water 1% F02045A VT-2AN.106 (2,7) 30 (113) 175 (662) VF3NLAFFF Aer-o-Lite 3% F02045B VT-2BN.205 (5,2) 27 (102) 231 (874) VF3NWAFFF-MS Aer-o-Water 3% EM F02045C VT-2CN.205 (5,2) 25 (95) 255 (965) SUPREME3G-ARC Universal Gold 3% F02045J VT-2JN.228 (5,8) 60 (227) 187 (708) VF1NWAFFF Aer-o-Water 1% F02044A VG-2AN.106 (2,7) 30 (113) 175 (662) VF3NLAFFF Aer-o-Lite 3% F02044B VG-2BN.205 (5,2) 27 (102) 231 (874) VF3NWAFFF-MS Aer-o-Water 3% EM F02044C VG-2CN.205 (5,2) 25 (95) 255 (965) SUPREME3G-ARC Universal Gold 3% F02044J VG-2JN.228 (5,8) 60 (227) 187 (708) VF1NWAFFF Aer-o-Water 1% F02050A VW-3AN.201 (5,1) 75 (284) 700 (2 650) VF3NLAFFF Aer-o-Lite 3% F02050B VW-3BN.300 (7,6) 30 (113) 600 (2 271) VF3NWAFFF-MS Aer-o-Water 3% EM F02050C VW-3CN.300 (7,6) 30 (113) 550 (2 082) SUPREME3G-ARC Universal Gold 3% F02050J VW-3JN.350 (8,9) 200 (757) 700 (2 650) VF1NWAFFF Aer-o-Water 1% F02046A VF-3AN.201 (5,1) 75 (284) 700 (2 650) VF3NLAFFF Aer-o-Lite 3% F02046B VF-3BN.300 (7,6) 30 (113) 600 (2 271) VF3NWAFFF-MS Aer-o-Water 3% EM F02046C VF-3CN.300 (7,6) 30 (113) 550 (2 082) SUPREME3G-ARC Universal Gold 3% F02046J VF-3JN.350 (8,9) 200 (757) 700 (2 650) VF1NWAFFF Aer-o-Water 1% F02051A VW-4AN.281 (7,1) 150 (568) 1200 (4 542) VF3NLAFFF Aer-o-Lite 3% F02051B VW-4BN.430 (10,9) 60 (227) 1300 (4 921) VF3NWAFFF-MS Aer-o-Water 3% EM F02051C VW-4CN.430 (10,9) 60 (227) 1300 (4 921) SUPREME3G-ARC Universal Gold 3% F02051J VW-4JN.455 (11,5) 400 (1 514) 1370 (5 186) VF1NWAFFF Aer-o-Water 1% F02047A VF-4AN.281 (7,1) 150 (568) 1200 (4 542) VF3NLAFFF Aer-o-Lite 3% F02047B VF-4BN.430 (10,9) 60 (227) 1300 (4 921) VF3NWAFFF-MS Aer-o-Water 3% EM F02047C VF-4CN.430 (10,9) 60 (227) 1300 (4 921) SUPREME3G-ARC Universal Gold 3% F02047J VF-4JN.455 (11,5) 400 (1 514) 1370 (5 186) VF1NWAFFF Aer-o-Water 1% F02052A VW-6AN.406 (10,3) 400 (1 514) 2600 (9 842) VF3NLAFFF Aer-o-Lite 3% F02052B VW-6BN.703 (17,8) 60 (227) 2750 (10 410) VF3NWAFFF-MS Aer-o-Water 3% EM F02052C VW-6CN.703 (17,8) 100 (378) 3000 (11 356) SUPREME3G-ARC Universal Gold 3% F02052J VW-6JN.803 (20,4) 675 (2 555) 3000 (11 356) VF1NWAFFF Aer-o-Water 1% F02048A VF-6AN.406 (10,3) 400 (1 514) 2600 (9 842) VF3NLAFFF Aer-o-Lite 3% F02048B VF-6BN.703 (17,8) 60 (227) 2750 (10 410) VF3NWAFFF-MS Aer-o-Water 3% EM F02048C VF-6CN.703 (17,8) 100 (378) 3000 (11 356) SUPREME3G-ARC Universal Gold 3% F02048J VF-6JN.803 (20,4) 675 (2 555) 3000 (11 356) VF1NWAFFF Aer-o-Water 1% F02053A VW-8AN.563 (14,3) 750 (2 839) 4000 (15 142) VF3NLAFFF Aer-o-Lite 3% F02053B VW-8BN 1.0 (25,4) 200 (757) 3900 (14 763) VF3NWAFFF-MS Aer-o-Water 3% EM F02053C VW-8CN 1.0 (25,4) 200 (757) 4000 (15 142) SUPREME3G-ARC Universal Gold 3% F02053J VW-8JN 1.3 (33,0) 1300 (4 921) 4000 (15 142) VF1NWAFFF Aer-o-Water 1% F02049A VF-8AN.563 (14,3) 750 (2 839) 4000 (15 142) VF3NLAFFF Aer-o-Lite 3% F02049B VF-8BN 1.0 (25,4) 200 (757) 3900 (14 763) VF3NWAFFF-MS Aer-o-Water 3% EM F02049C VF-8CN 1.0 (25,4) 200 (757) 4000 (15 142) SUPREME3G-ARC Universal Gold 3% F02049J VF-8JN 1.3 (33,0) 1300 (4 921) 4000 (15 142)

March 1, 2001 210 e ME TERING PRES SURE DROP vs. FLOW RATE

210 f March 1, 2001 PER MA NENT PRES SURE LOSS vs. FLOW RATE Replaces page 860 a-f, dated March 25, 1999. Re - placed 3M reference with National Foam, added drawings and revised page number. Form No. F_041497