Data Sheet Presetting Valve Type RA-N with Flange Connection The setting options range from kv = 0.08-0.67 m3/h. Kvs = 0.88 m3/h Application The valve is deliveres assembled including mounted air ventilation screw and protective cap, red. All Danfoss thermostatic sensors in the RA series can be combined with the RA-N valve. The RA-N valve, code no. 03G843, is specially designed for Russain convectors with 50 mm bottom connection. In order to avoid deposition and corrosion, the composition of the hot water must be in accordance with the VDI 2035 guideline (Verein Deutscher Ingenieure). The valve body is designed for two-pipe pumped systems in commercial or domsetic heating systems. RA-N has a built-in facility for setting max. flow through the convector. System Presetting Presetting area Reference mark The presetting values of the integrated valves can be adjusted easily and accurately without the use of tools (factory setting: N ): Danfoss Heating Solutions VDGWG02 Danfoss Remove the protective cap or the thermostatic sensor Find the reference mark Turn the setting ring until the desired presetting number aligns with the reference mark. 0/202
Presetting can be selected within the range of to 7. At setting N the valve is fully open. Setting in the shaded areas of the drawing should be avoided. When the thermostatic sensor is fitted, the presetting is hidden and thus protected against unintended alteration. Setting N is used when flushing the system. Technical Data k v -values ) Setting 2 3 4 5 6 7 N K vs N kv-value 0.08 0.2 0.8 0.25 0.32 0.42 0.53 0.67 0.88 Code no. Max. water temp. Differential pressure 2) Rec. Tech. Test pressure Work. pressure C bar bar bar bar 03G843 20 0.05-0.2 0.6 25 6 ) The kv-value indicates the water flow (Q) in m3/h at a given lift and a pressure drop ( p) across the valve at bar. kv = Q / p. At setting N the kv-value is stated according to EN 25, at Xp = 2 K. At lower presetting values Xp is reduced to setting, Xp = 0.5. At presettings between and N, Xp is between 0.5 and 2 K. 2) Xp = 2 K means that the valve is closed at 2 C higher room temperature. The kvs-value states the flow Q at a maximum lift, i.e. at fully open valve. The max. differential pressure specified is the maximum pressure at which the valve gives satisfactory regulation. As with any device which imposes a pressure drop on the system, noise may occur under certain flow/pressure conditions. A differential pressure between 0. and 0.3 bar across the valve is recommended. The differential pressure can be reduced using Danfoss differential pressure regulators. Design Materials in contact with water : Valve body and other metal parts Throttle nozzle and spindle O-ring Valve cone Pressure pin in gland seal Ms 58 brass PPS EPDM NBR Chrome steel Accessories Gland seal Important Should the valve body gland seal show signs of leaking, the gland can be replaced quickly without draining down the system. After mounting the gland seal, press pin firmly to ensure proper contact to the valve spindle. Gland seals are delivered in boxes of 0 units complete with instructions. Code no.: 03L0669 2 VDGWG02 Danfoss 0/202 Danfoss Heating Solutions
Dimensions 3,5 G3/4 A ISO 228/ 29 23 G3/4 A ISO 228/ 26 5 8,5 Convector Integration B 26±0,3 0,5 A UNION NUT A 40±0,3 80 80 0,2 B UNION NUT DETAIL A SCALE :2,5 25 30 50 PIPE CONNECTION SCALE :2,5 50 0,,6 2,5±0,5 R0,5 max. ø2,4 23,7±0,2 max. 7 SCALE : Sizing Example Known values Heat demand: Φ = 500 kcal/h System temperature drop: t = 20 C Differential pressure: p = 0.0 bar Calculation Water quantity Q (Φ/ t) = 500/20 = 75 l/h Q p 0.075 0. K v = = = 0.23 m 3 /h The setting is found in the capacity diagramme below: Presetting 3. If the sizing point found is between two settings, the highest setting is chosen. Alternatively, the settings can be found directly in the table technical data. Danfoss Heating Solutions VDGWG02 Danfoss 0/202 3
Capacity Diagramme (without radiator and tubing) 0 03G843 RA-N 2 3 4 5 6 7 N 00 8 0,8 80 6 5 4 0,6 0,5 0,4 60 50 40 3 0,3 30 2 0,8 p [mwg ] 0,2 p [bar ] 0, 0,08 20 p [ kpa ] 0 8 0,6 0,5 0,4 0,06 0,05 0,04 6 5 4 0,3 0,03 3 0,2 0,02 2 0, 0,0 5 7 0 20 30 40 50 70 00 200 300 400 500 700 000 Q [l/h] 2000 o t=0 C 0,07 0, 0,2 0,3 0,4 0,5 0,7 2 3 4 5 7 0 20 kw t=5 C o o t=20 C 0,2 0,3 0,4 0,5 0,7 2 3 4 5 7 0 20 30 40 kw 0, 0,2 0,3 0,4 0,5 0,7 2 3 4 5 7 0 20 30 kw Instructions ) 2) 3) 4) 4 VDGWG02 Danfoss 0/202 Danfoss Heating Solutions
5) 6) Max. temperature 20ºC Max. temperature 20ºC 60Nm Danfoss Heating Solutions VDGWG02 Danfoss 0/202 5
6 VDGWG02 Danfoss 0/202 Danfoss Heating Solutions
Danfoss Heating Solutions VDGWG02 Danfoss 0/202 7
Danfoss A/S Heating Solutions Haarupvaenget 8600 Silkeborg Denmark Phone: +45 7488 8000 Fax: +45 7488 800 Email: heating.solutions@danfoss.com www.heating.danfoss.com Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss Heating Solutions and the Danfoss Heating Solutions logotype are trademarks of Danfoss A/S. All rights reserved. 8 VDGWG02 Danfoss 0/202 Danfoss Heating Solutions