CLAM PASS RESTORATION AND MANAGEMENT PLAN BATHYMETRIC MONITORING REPORT NO. 7 Including Interior Bay Dredge Cuts and Tidal Data

CLAM PASS RESTORATION AND MANAGEMENT PLAN BATHYMETRIC MONITORING REPORT NO. 7 Including Interior Bay Dredge Cuts and Tidal Data Submitted to: Florida Department of Environmental Protection DEP File No. 01284163-001-JC Submitted by: Pelican Bay Services Division, Collier County Prepared by: Humiston & Moore Engineers HM File No. 9-068/13-078 January 2007 Main Office : 5679 Strand Court Naples, FL 34110 Phone 239 594 2021 Fax 239 594 2025 e-mail : mail@humistonandmoore.com East Coast Office : 805 East Hillsboro, #103 Deerfield Beach, FL 33441 Phone 954 428 2550 Fax 954 428 4733 web site : www.humistonandmoore.com

CLAM PASS BATHYMETRIC MONITORING REPORT NO. 7 Including Interior Bay Dredge Cuts and Tidal Data CONTENTS 1. Summary...4 2. Introduction...5 3. Inlet Cross Sections...5 4. Interior Channels...15 5. Tidal Study...15 6. Shoreline Change...20 7. Conclusions and Recommendations...24 8. Recommendations for Ongoing Monitoring...25 9. Previous Recommendations...25 10. Comments on CP&E Independent Analysis of Clam Pass...26 11. References...29 LIST OF TABLES 1. Average Cross Sectional Areas Cut #4...10 LIST OF FIGURES 1. Clam Bay Site Plan...6 2. Clam Pass Dredge Cut #4...8 3. Average Cross Section of Flow in Cut #4 Segments...11 4. Cumulative Shoaling in Cut #4 Segments...12 5. High Tide Phase Lag...17 6. Low Tide Phase Lag...18 7. Clam Bay Tidal Range...19 8. Relative Shoreline Position In Comparison to 1999...21 9. Clam Pass Contours...23 APPENDICES Appendix A, Cut #1...30 A-1 Aerial A-2 Cross Sectional Area Chart A-3 Cross Sectional Area Table A-4 Cross Sections (0+00 to 2+46) A-5 Cross Sections (3+43 to 6+59) A-6 Cross Sections (7+21 to 8+59)

Appendix B, Cut #2...37 B-1 Aerial B-2 Cross Sectional Area Chart B-3 Cross Sectional Area Table B-4 Cross Sections (0+00 to 2+66) B-5 Cross Sections (3+13 to 6+01) Appendix C, Cut #3...43 C-1 Aerial C-2 Cross Sectional Area Chart C-3 Cross Sectional Area Table C-4 Cross Sections (0+00 to 2+95) C-5 Cross Sections (3+65 to 7+03) C-6 Cross Sections (7+54) Appendix D, Cut #4...50 D-1 Aerial D-2 Cross Sectional Area Chart (0+00 TO 7+10) D-3 Cross Sectional Area Chart (7+50 TO 18+28) D-4 Cross Sectional Area Chart (18+70 TO 35+37) D-5 Cross Sectional Area Table D-6 Cross Sections (0+00 to 0+50) D-7 Cross Sections (0+75 to 1+25) D-8 Cross Sections (1+50 to 2+00) D-9 Cross Sections (2+37.5 to 3+64.5) D-10 Cross Sections (4+10 to 5+10) D-11 Cross Sections (5+60 to 6+60) D-12 Cross Sections (7+10 to 8+00) D-13 Cross Sections (8+50 to 9+50) D-14 Cross Sections (10+00 to 10+50) D-15 Cross Sections (11+00 to 12+00) D-16 Cross Sections (12+50 to 13+50) D-17 Cross Sections (14+00 to 15+00) D-18 Cross Sections (15+50 to 16+50) D-19 Cross Sections (17+00 to 18+00) D-20 Cross Sections (18+28 to 19+21) D-21 Cross Sections (20+82 to 22+20) D-22 Cross Sections (23+10 to 25+84) D-23 Cross Sections (26+39 to 29+13) D-24 Cross Sections (29+89 to 31+53) D-25 Cross Sections (32+04 to 34+23) D-26 Cross Sections (34+72 to 35+37) D-27 Inlet Volume Dredge and Cumulative Volume Dredge D-28 Cross Sections (3+65 to 7+03) Appendix E, Beach Profiles...77 E-1 Aerial E-2 Reference Monument Plots (R-38 to R-41) E-3 Reference Monument Plots (R-42 to R-44) E-4 Shoreline Position Relative to DEP Monument l E-2 Shoreline Change June 05 July 06 E-2 Shoreline Change 1999 2006

CLAM PASS RESTORATION AND MANAGEMENT PLAN BATHYMETRIC MONITORING REPORT NO. 7 January, 2007 1. Summary The Clam Pass Restoration and Management Plan was implemented in 1999 to improve flushing of the Clam Bay System and mangrove preserve. Additionally, the flood tidal shoal and some of the interior waterways were dredged at the same time to improve the hydraulic efficiency of the inlet and increase the tidal prism. The improved tidal prism means more water goes in and out of Clam Pass on each tidal cycle and this larger volume of water generates stronger currents in the inlet which help to keep the inlet open and maintain the flushing improvements. Since the 1999 dredging, annual monitoring data has continually shown that implementation of the dredging element of the Clam Bay Restoration and Management Plan has significantly improved tidal exchange throughout the bay system. The maintenance dredging of the flood shoals in January 2002 was shown to be beneficial to maintaining the improved tidal prism. Seven years after the initial dredging in 1999 and nearly four years after the maintenance dredging of the flood shoals in 2002, monitoring data show the average cross sectional flow area through the inlet remains at more than twice the cross sectional area prior to the 1999 dredging. Additionally, the tidal ranges and phase lags continue to show that the bay system is flushing more effectively than prior to the 1999 dredging. The 2005 Monitoring report recommended that another maintenance dredging event be schedule for the winter of 06/07. In response to this recommendation a Notice to Proceed has been granted by the Florida Department of Environmental Protection to conduct another maintenance dredging of Clam Pass. The maintenance dredging will be limited to Cut 4 between stations 0+00 and 18+00, which are located at the entrance of the inlet, and portions of the flood shoal. No dredging is currently proposed for any of the interior channels (18+28 through 35+37) including cut #1, cut #2, and cut #3. The 2006 average cross sectional area is nearing or surpassed the shoaling conditions which existed prior to the maintenance dredging which was completed in 2002. Although the tidal data shows that flow through the inlet is still significantly stronger than the pre-1999 conditions and may be sufficient to maintain flushing to the bay for the time being, there are indications that the flow through the inlet has diminished somewhat since the 2002 dredging. In order to reduce the potential for tidal exchange being diminished to the point where flushing might be inadequate, maintenance dredging is scheduled for early in 2007. There has been recent discussion about Collier County expanding the dredging to include the ebb shoal for the purpose of obtaining additional sand for nourishment of the Clam Pass Park beach. This approach would provide immediate relief to the erosion problem on the park beach; however, it may also have long term consequences that should be carefully considered because a common impact from dredging inlet ebb shoals is increased erosion of adjacent beaches.

2. Introduction This report was prepared to fulfill the requirements of DEP permit 0128463-001-JC and presents the ninth set of monitoring data collected following implementation of the dredging element of the Clam Bay Restoration and Management Plan in April 1999. Previous monitoring of Clam Pass dredging has been reported in Clam Pass Bathymetric Monitoring Reports numbered 1 through 8 which document dredging events and rates of shoaling in Clam Pass in fulfillment of Florida Department of Environmental Protection Special Permit Condition 10 contained in Permit No. 0128463-001-JC. Due to the dynamic nature of Clam Pass and the importance of maintaining the tidal flow to the Clam Bay system, Collier County had dredged Clam Pass in the spring of every year from 1995, to 1999. The dates and permit references under which dredging had been conducted from 1995 to 1999 are presented in earlier monitoring reports. In 1999, the pass was dredged under JCP permit 0128463-001-JC, as part of the implementation of the Clam Bay Restoration and Management Plan, which included dredging portions of the flood shoals and inner channels to improve the hydraulic stability of the inlet and reduce flow restrictions to and from Upper Clam Bay and Inner Clam Bay. Figure 1 shows the cuts which were dredged as part of the Restoration and Management Plan. The most recent dredging of Clam Pass was completed in January 2002, as maintenance dredging under the same permit. The portion of Cut 4 which lies close to the inlet is the most rapid shoaling area in the system, and is the part of the project which required maintenance dredging in 2002. Another maintenance dredging event is schedule for early in 2007, which will also be completed under the JCP permit 0128463-001-JC and limited to Cut 4. This report presents the results of the July 2006 monitoring of the inlet plus the immediate vicinity, which has been covered in previous monitoring reports. Additionally, this report includes monitoring of the inner channels. The inner channels are monitored on two year intervals because previous monitoring has demonstrated that the shoaling rates in these areas are much lower than the rates in the entrance channel and flood shoal. Figure 1 is a location map of the study area, which shows the locations of the four dredge cuts and the beach profiles surveyed at the DEP reference monuments. 3. Inlet Cross Sections The channel cross section plots for Clam Pass and the flood shoal are presented in Appendix D. This includes stations 0+00 through 18+00 of Cut #4 which is the entrance channel and the portion of Cut #4 subject to the most active shoaling. Figures D-1 through D-21 show the November 1999 post dredging survey in comparison to the two most recent monitoring surveys from June 2005 and July 2006. Figure 2 illustrates the location of the monitoring stations. Cuts 1, 2, and 3 are inner channel cuts which will be discussed later. Clam Pass is a relatively small inlet with a relatively small tidal prism, and therefore has limited tidal energy to generate currents to scour sand from the channel. Because of this the inlet dynamics are predominately wave induced rather than tidally induced, it is susceptible to migration or even closure. The problem manifests itself when storm waves generate high levels of littoral transport along the beach, which may deposit significant amounts of sand in

the inlet. The effects of storms on the inlet are, however, highly variable because high storm surge associated with some storms may generate strong tidal currents and scour action to offset the shoaling caused by wave induced sand transport. This is what happened at Clam Pass during Tropical Storm Gabriel in 2001. The 2006 monitoring data illustrates the weather dependent variability of inlet dynamics. Figure D-5 shows that an increase in the cross sectional area of flow has occurred between July 2005 and July 2006 near the entrance of the inlet, at stations 0+00 to 1+00, while a decrease in cross sectional area occurred on most of the stations between 1+50 and 10+00 within the interior portions of the inlet The increase in channel cross sectional area between stations 0+00 and 1+00 is due to the onshore migration of the ebb shoal due to wave action, resulting in a general deepening of the nearshore area around the inlet entrance. A significant amount of this sand moved onshore, primarily south of the inlet, however, some of the sand was pulled into the interior potions of the inlet and deposited on the flood shoal. The onshore movement of sand from the ebb shoal onto the beach south of the inlet is part of the natural process by which littoral drift bypasses the inlet. This illustrates why inlet sand bypassing may be more of a cyclical process as opposed to a steady process in which a predictable amount of sand may be expected to bypass on an annual basis. Channel cross sectional flow area represents an important indication of the stability of the inlet. The most active region of cut #4, in terms of sand transport and shoaling, is divided into three segments to evaluate the general conditions of cross sectional area and shoaling, as defined below and illustrated in figure 2. Segment # Station Limits A 0+00 to 3+00 B 3+65 to 6+10 C 6+60 to 18+00 Segment A is the most active zone which includes the cut across the landward portion of the flood shoal and the beach. Segment B includes the portion of the flood shoal closest to the inlet. The channel is wider in segment C, which may be considered the inner portion of the flood shoal, and current velocities are therefore lower in this segment. The lower current velocities allow shoaling to occur here when sand is pulled into the inlet on flood tide. Segment A is typically the most dynamic because it crosses the littoral zone. Rapid shoaling may occur here during periods of high wave energy when littoral transport rates along the beach are high. Strong tidal currents may scour some of that sand out of the channel, particularly during a storm surge, or spring tide which is the part of each month when tidal currents are the strongest. To some extent the same is true for segment B because sand scoured from A on a flood tide is carried into B and C. Segment C has the largest cross section and therefore the slowest currents, and sediment that reaches this interior part of the flood shoal therefore tends to accumulate there until it is dredged. Dredging that keeps C open helps to maintain the strong tidal currents that are capable of scouring sand out of A and B. Table 1 and Figure 3 illustrate the variability that occurs from shoaling which decreases the cross section and scour which opens it back up again. Note that the cross sectional area for A and B fluctuates about the 200 square feet level, indicating that this is close to the equilibrium cross sectional area. Segment C, however, shows a tendency for the cross

section to steadily decrease following a dredging event. If the cross sectional area of C gets down to the 200 feet level, there is not enough tidal energy to overcome the frictional resistance to flow through a channel of the combined lengths of A, B, and C, and all three segments will continue to shoal and the potential for inlet closure increases. In this analysis, the channel width is measured at 0 ft. NGVD and the cross sectional area is calculated from the area bound by the bottom profile and 0 NGVD elevation. The 0 NGVD contour is used as a common datum for shoreline positioning. For reference purposes, mean high water (MHW) for this area is +1.5 feet above NGVD, mean tide level is +0.5 feet above NGVD, and mean low water (MLW) is 0.5 feet below NGVD 1. 1 The elevations of Mean High Water (MHW) and Mean Low Water (MLW) are based on DEP Special Report No. 87-2, Predicted Open Tidal Datums for the Florida Lower Gulf Coast, Balsillie, 1987, and discussions with the DEP Bureau of Survey and Mapping.

The cross sectional areas have been averaged within each segment for the surveys as shown in Table 1: Table 1 Average Cross Sectional Areas within Active Portion of Cut #4 Clam Pass Monitoring 1998 to 2006 Date of Survey Description of Survey Avg. Area (ft 2 ) Segment A Avg. Area (ft 2 ) Segment B Avg. Area (ft 2 ) Segment C 10/1998 Pre-dredge 96 85 66 04/1999 Post dredge 417 301 432 05/2000 13-month monitoring 180 198 360 02/2001 21-month monitoring 185 205 no data 09/2001 Post Tropical Storm Gabrielle 298 243 312 12/2001 Pre-maintenance dredge 301 240 342 02/2002 Post maintenance dredge 296 399 no data 04/2002 36-month monitoring 276 317 558 06/2003 50-month monitoring 177 186 537 11/2003 Post storm 270 212 510 05/2004 60-month monitoring 220 259 479 06/2005 74-month monitoring 156 215 332 07/2006 87-month monitoring 324 181 305 Note: Monitoring time is in reference to completion of the April 1999 dredging. All three segments were dredged in 1999. Only segments B and C were dredged during the January 2002 maintenance dredging. Following the maintenance dredging in 2002, Segment A experienced shoaling in response to high wave energy. The shoaling took the form of a sand spit that grew across the inlet entrance from the south causing the inlet entrance to migrate north approximately 400 feet. In October 2002 scour from tidal currents during an elevated storm tide reopened Segment A along the dredged channel alignment. This is an example of how the increased tidal prism and stronger tidal flow resulting from the 1999 dredging has been effective in maintaining the average channel cross section above the pre-dredge condition in 1998. Based on the most recent monitoring of July 2006, the average cross sectional area in each of the three segments remains substantially above the 1999 pre-dredge condition. As in 2002, the 2006 monitoring data also indicate a high wave energy event affected the region landward transport of sand from segment A which increases the cross sectional area of flow, while decreasing sections B and C. In addition, it is evident through Table 1 that the average cross sectional area of flow of Segments A, B, and C are close to the levels of the December 2001 pre-maintenance dredging. Figure 3 presents a time series plot of the average cross sectional areas from Table 1. This further indicates that maintenance dredging is needed. A detailed listing of individual cross sectional areas for each station is presented in Appendix D. Another way to evaluate the stability of the inlet is to consider the amount of sand which is accumulating within each of the three segments. The volume of sand accumulated in each segment was calculated based on surveys conducted since the dredging of the inlet in April 1999. The results are presented in Figure 4, which represents the cumulative volumetric change within each segment. The volumetric change is presented as a total volume change measured across the entire surveyed cross section, and therefore may actually be more

than the total amount of sand accumulated within the limits of the designated dredge cut. In general, the total cumulative volume would normally be greater than that which accumulated within the more limited area between the dredge limits, which is apparent for Segment A in Figure 4. The baseline for the dredge cut volume is the dredge template; following a dredging event the dredge cut volume would be zero if all the lines and grades were achieved. In practice a small amount of material has been left in the dredge cut because there are some areas where the digging depth has been decreased to avoid excavating undesirable material. For convenience, the baseline for the total cumulative volume was arbitrarily established as the same value as the dredge cut volume for the 1999 post dredging data point on figure 4. This is why the total dredge cut volume may be a negative number if overdredging occurs beyond the lines and grades of the dredge cut. The total cumulative volume on Figure 4 is therefore to illustrate relative change for the purposes of comparison, but the actual values are arbitrary. The cumulative shoaling which has occurred since the 1999 dredging was summarized in previous reports and is reproduced below for convenience, because this describes how the increased tidal prism helps the inlet maintain itself, and how this process is affected by storm events. The summary below was updated to include the most recent monitoring interval: April 1999 to May 2000: Following the comprehensive dredging completed in April 1999, shoaling occurred in all three segments. This indicates that all three of these segments are within the active littoral portion of the inlet system. For Segment A, approximately 50% of the shoaling occurred within the dredge cut, the remainder represents material which accumulated in the ebb shoal or on the beach adjacent to the dredge cut. Practically all of the shoaling occurred within the dredge cut limits in segments B and C. May 2000 to February 2001: During this time period shoaling continued in Segment A yet at a slower rate, probably because the inlet cross sectional area was near an equilibrium condition where tidal currents were able to scour sand from the channel at approximately the same rate that wave action deposited sand in the channel. Segment B showed very little volumetric change. Segment C was not surveyed as part of the February 2001 survey. In general, the flattening of the cumulative shoaling curve indicates that segments A and B appear to be close to equilibrium. September 14, 2001: This interval was impacted by Tropical Storm Gabrielle. Segment A shows that in spite of storm waves that would tend to push sand into the inlet, strong tidal currents associated with the elevated storm tide scoured sand out of the inlet entrance. This restored the entrance channel to the straight alignment that had been dredged as a design element of the Restoration and Management Plan. This is a direct indication of successful establishment of improved inlet hydraulics from the 1999 implementation of the dredging element of the Restoration and Management Plan. February and August 2001 to September 19, 2001: Impacts of tropical storm Gabrielle are evident within each segment. The inlet channel in the seaward Segment A was scoured and enlarged due to strong currents accompanying the storm surge as discussed above. Segment B remained essentially the same; however, some of the sand scoured from Segment A during Gabrielle was carried in the inlet and deposited on the inner shoal in Segment C. This contributed to the increase in sand volume in Segment C for this

monitoring interval. It should be understood that Segment C is dredged to a much larger channel flow cross section than the entrance channel, so that a substantial amount of sand can accumulate in Segment C before it begins to adversely affect inlet hydraulics. This area is designed to act as a deposition basin which becomes a source of sand for beach nourishment when inlet dredging becomes necessary. September 2001 to December 2001: A pre-dredge survey was conducted in December 2001. This survey showed shoaling in Segment A subsequent to the scour which occurred during tropical storm Gabrielle. This shoaling represents reestablishment of the shoal volume which was diminished due to onshore transport during the storm. A slight reduction in volume was evident in segments B and C over this time. These changes probably represent redistribution of sand along the channel from tidal currents. A decrease in sand volume in segment C is unusual and may be the result of changes in the shape or location of the channel because the shoal geometry which formed under impacts of the storm is likely to be different to the geometry that conforms to normal tidal flow. December 2001 to January 2002: Segments B and C were dredged during this interval. This was maintenance dredging to prevent accumulation from reaching levels that could adversely affect inlet hydraulics and the self scouring capability of the inlet. Approximately 11,500 cubic yards of sand were dredged from these two segments. The sand was used to mitigate beach erosion on the county park south of the inlet. Segment A was not dredged except for a small amount of dredging that was necessary to get the dredge in the inlet. January 2002 to February 2002: Immediately following the dredging, the Segment A channel cross section increased in size due to the scour action of improved hydraulics resulting from the dredging. Segments B and C began to shoal. February 2002 to June 2003: Shoaling occurred in all three segments similar to the time period following the 1999 dredging. June 2003 to November 2003: An elevated storm tide impacted the area, and sand was again scoured from segments A, and B. Some of this sand was carried in the inlet and deposited in Segment C. November 2003 to May 2004: Minor shoaling occurred in segments A and C with minor scouring in Segment B. There were no significant storm events and these changes should be considered normal redistribution of sediments along the channel from tidal currents. May 2004 to June 2005: Shoaling occurred in all three segments. Some of the shoaling in A was the result of formation of a sand spit growing into the inlet from the south side, resulting in northward migration of the inlet. June 2005 to July 2006: Shoaling occurred in sections B and C, but there was a decrease of sand volume in section A. The decrease of material in section A is probably related to the 2005 Gulf Hurricane Season, during which there were periods of extreme waves and tidal elevations. These conditions resulted in a general lowering of the elevation of the flood shoal due to onshore movement of sand, and potentially scour due to higher current velocities associated with higher tide elevations. An increase in beach width on the south side of the inlet indicates that the onshore movement of sand from the flood shoal benefited the park beach to the south. Since a significant amount of the material in the ebb shoal

probably came from beaches to the north, this onshore movement is actually part of the normal inlet sand bypass process. The lower tidal velocities in segment C are less effective at scouring sand from the channel, resulting in more rapid accumulation of sand in Segment C under storm conditions. The project was designed this way, because sand can accumulate in Segment C for a longer period of time before the channel becomes restricted to a point where inlet hydraulics my be adversely affected. The monitoring data over the past 7 years show that the dredging completed in 1999, which removed a significant portion of the flood shoal, has resulted in improved stability of the inlet system. The improved tidal prism which resulted from the dredging has allowed the inlet to sustain the impact of the kind of storms which previously had a history of closing the inlet. Figure 4 also provides an overall estimate of the volume of sand within the three segments. Currently there are a total of approximately 12,000 cubic yards of sand within the dredge limits of segments A through C. In comparison, approximately 19,000 cubic yards of sand were dredged from the design cut from these three segments in 1999. Segments B and C contain approximately 9,400 cubic yards in comparison to 11,725 cubic yards that was removed in the 2002 maintenance dredging. 4. Interior Channels The interior channel cut locations are shown on Figure 1. The cuts selected for dredging were identified as channel sections which presented restrictions to flow in comparison to other channel sections within the bay system. Appendix A includes a detailed site plan for each dredge cut, cross sections at nominal intervals along each cut, and an illustration of the channel cross sectional area at each station from pre-dredge, post dredge, and most recent surveys. This information shows that the cross sectional area was significantly improved by dredging, and in all but few locations the cross sectional area has changed very little since the initial dredging. This illustrates the difference between the dynamic inlet entrance of Cut 4, which is exposed to high littoral sand transport rates, and interior channels of Cuts 1, 2, and 3, which are not. Dredging of the interior channels has contributed to the improved hydraulic efficiency of the bay system and the inlet, however, it is not anticipated that the interior channels will require maintenance dredging as frequently as is anticipated for cut #4 in the immediate vicinity of the inlet. The 2006/2007 dredging event will not include the interior cuts because little shoaling has occurred since the initial 1999 dredging event occurred. Since the shoaling rate in the less dynamic inner area has been shown to be very slow, it is recommended that surveys continue to be conducted under the monitoring program. However, a survey interval of 4 years should be sufficient for monitoring these relatively stable areas. 5. Tidal Study Prior to the commencement of the March 1999 dredging, water level recording gauges were installed at selected locations within the Clam Bay estuarine system and Gulf of Mexico to measure tidal ranges. Tides along the southwest Florida Coast are mixed; they exhibit

either diurnal (one tide per day) or semidiurnal (two tides per day) characteristics during each month depending on the phase of the lunar cycle. Pre-construction tidal data was collected for a full month to obtain average values representative of the general tidal characteristics for Clam Bay, and to establish baseline conditions against which improvements to tidal flow could be measured. The locations of the gages are included in Figure 1. The mixed tide characteristics of this area are important to those who frequently visit the inlet and witness short term changes. During the neap tide part of the month when tidal currents are not particularly strong, the inlet may take on wave dominant characteristics and appear to be shoaling near the entrance, particularly if the neap tide coincides with high wave energy events. During the ensuing spring tide, roughly two weeks later, tidal currents are considerably stronger and may efficiently scour out shoals that formed during the neap tide two weeks earlier. The purpose of the monitoring program is to monitor inlet characteristics on a more comprehensive long term basis, with less emphasis on day to day or week to week changes. One of the parameters monitored during the tidal study is tidal phase lag. This is the time difference between the high and low tide in the Gulf of Mexico and the corresponding high or low tide in the bay. The magnitude of the phase lag is an important indicator of inlet dynamics. Figures 5 and 6 show a comparison of the tidal phase lag at high and low tide conditions at three tide gage locations within the bay system. In each case the phase lag was reduced as a result of the dredging, indicating that the filling and draining of the bay occurred more quickly due to less resistance to flow at the inlet. Additionally, the pre-dredge low tide phase lag was larger than the pre-dredge high tide phase lag and the post-dredging low and high tide phases are now very similar. This asymmetric improvement is because the dredge cut represents a much greater percentage increase in cross section of flow near low tide than it does at high tide. This is illustrated by some of the more heavily shoaled areas that were so clogged with sand that they would be nearly dry at low tide, whereas after the dredging those areas are deep enough to support significant tidal flow even on the lowest tides. This enhanced flow near low tide contributed significantly to the improved tidal exchange. The most recent tidal data, from August through September 2006, shows an overall small decrease in the high tide and low tide phase lags over the previous period, with the exception of the data from the tide gage near the Registry Resort. The Registry tide phase lag increased by two-fold which is unrealistic and indicative of a faulty tide gauge. The data from this gage will therefore be not be considered in the analysis. The decrease in the phase lags at the other gage locations may be attributed to the increase in flow cross section in segment A. The tide phase lags remain significantly below the pre-1999 dredging conditions, indicating that the improvements continue to support better tidal circulation and hydraulic efficiency of the inlet.

3:00:00 2:00:00 1:00:00 0:00:00 High Tide Phase Lag CLAM PASS MONITORING Pre-Dredge Post-Dredge 10-20-99 : 01-23-00 03-15-00 : 04-27-00 06-05-00 : 07-31-00 09-29-00 : 10-21-00 12-08-00 : 01-14-01 02-22-01 : 05-03-01 07-01-01 : 08-26-01 09-20-01 : 11-09-01 01-22-02 : 03-25-02 04-26-02 : 07-10-02 07-25-02 : 09-28-02 11-21-02 : 02-10-03 05-03-03 : 06-29-03 09-03-03 : 11-18-03 02-07-04 : 03-28-04 04-06-04 : 06-05-04 04-16-05 : 06-23-05 07-28-05 : 11-04-05 8-03-06 : 09-26-06 No Data Collected No Data Collected No Data Collected Faulty Gauge No Data Collected No Data Collected Registry South North Location Hours FIGURE 5

3:00:00 2:00:00 1:00:00 0:00:00 Low Tide Phase Lag CLAM PASS MONITORING Pre-Dredge Post-Dredge 10-20-99 : 01-23-00 03-15-00 : 04-27-00 06-05-00 : 07-31-00 09-29-00 : 10-21-00 12-08-00 : 01-14-01 02-22-01 : 05-03-01 07-01-01 : 08-26-01 09-20-01 : 11-09-01 01-22-02 : 03-25-02 04-26-02 : 07-10-02 07-25-02 : 09-28-02 11-21-02 : 02-10-03 05-03-03 : 06-29-03 09-03-03 : 11-18-03 02-07-04 : 03-28-04 04-06-04 : 06-05-04 04-16-05 : 06-23-05 07-28-05 : 11-04-05 08-05-06 : 09-24-06 Registry South North Location Hours No Data Collected No Data Collected No Data Collected Faulty Gauge No Data Collected No Data Collected FIGURE 6

2.50 2.00 1.50 1.00 0.50 0.00 CLAM BAY TIDAL RANGES PRE-DREDGE RANGE POST-DREDGE RANGE 10/99-01/00 RANGE 03/00-05/00 RANGE 06/00-07/00 RANGE 09/00-10/00 RANGE 12/00-01/01 RANGE 02/01-05/01 RANGE 07/01-08/01 RANGE 09/01-11/01 RANGE 01/02-03/02 RANGE 04/02-07/02 RANGE 07/02-09/02 RANGE 11/02-02/03 RANGE 05/03-06/03 RANGE 09/03-11/03 RANGE 02/04-03/04 RANGE 04/04-06/04 RANGE 03/05-06/05 RANGE 07/05-11/05 RANGE 08/06-09/06 RANGE Gauge flooded, no data available Gauge not functioning, no data recorded Gauge flooded, no Data Collected No Data Collected No Data Collected No Data Collected No Data Collected Gauge down through 9/28/00 for repair of Naples Pier Preliminary tide data - not to be used for design purposes No NOAA Gulf data from 4/4/01 to No NOAA Gulf Data from 8/1/01 to `8/6/01 GULF REGISTRY SOUTH NORTH LOCATION TIDAL RANGE (FEET) FIGURE 7

The relative tidal range was also evaluated for the post 1999 dredging conditions at each tide gage location as illustrated in Figure 7. In each case there was a significant increase in the tidal range as a result of the March 1999 Clam Bay Restoration dredging project. The dredging opened up the channel and reduced resistance to flow, thereby allowing more water into the bay in a shorter period of time. Since more water gets into the bay on flood tide and more leaves on ebb tide as a result of the reduced restrictions to flow, the average tidal range increased. The January 2002 maintenance dredging appears to have helped to maintain the improved tidal range, which remains significantly above the pre-1999 dredging range. The most recent tidal data, from July 28 2005 through November 04, 2005, and August 08, 2006 through September 24, 2006 show that the tide ranges have remained significantly higher than the pre-1999 dredging condition. 6. Shoreline Change Plots of wading depth profiles surveyed at DEP reference monuments R-38 through R-44 are presented in Appendix C. The beach profiles include data collected in 1999 plus the two most recent annual monitoring surveys to illustrate both cumulative and recent changes. The monitoring program includes profiles at 4 monuments north of the inlet, R-38 to R-41 and 3 monuments south of the inlet, R-42 to R-44. The following discussion considers the position of the 0 NGVD contour for evaluating changes in shoreline position. Over the most recent monitoring interval, the beach stations to the north of the inlet eroded, while south of the inlet both accretion and erosion occurred. The beach at 4 monuments R- 38 through R-41 north of the inlet receded an average of approximately -25 feet, with the most severe erosion of -33.6 feet at R-41, the station closest to the inlet. For the purpose of comparison to an equivalent length of shoreline represented by the three monuments surveyed south of the inlet, the average change for the three monuments R-39 to R-41 closest to the north side of the inlet was erosion of -28 feet. South of the inlet the beach accreted at R-41 and R-44, and eroded at R-42 between June 2005 and July 2006. The average change for these three stations was accretion of approximately 10 feet. The reason part of this area accreted and part eroded is probably due to sand bypassing the inlet and moving onshore, with an uneven distribution of that material due to wave refraction patterns across uneven nearshore contours illustrated in Figure 9. Figure 8 shows a history of shoreline position relative to the 1999 post construction survey. This figure illustrates the longer term changes that have occurred since the 1999 dredging and beach fill. This shows that the beach 2,000 to 3,000 feet north of the inlet at R-38 and R-39 has increased in width by approximately 14 feet since 1999, with most of that increase occurring by April 2002. Closer to the inlet, at R-41, the beach width has fluctuated more dynamically over this period, however, due to recent erosion the net change has been shoreline recession of -56 feet between April 1999 and July 2006. Figure 8 shows that the shoreline at R-42 immediately south of the inlet has experienced both periods of erosion and accretion, and by July 2006 the shoreline was in the same position as 1999. The shoreline at R-43, 1000 feet to the south receded a total of -93 feet

40 20 0-20 -40-60 -80-100 RELATIVE SHORELINE POSITION IN COMPARISON TO 1999 CLAM PASS MONITORING 1999-2006 Apr-99 Apr-02 Jun-03 Nov-03 May-04 Jun-05 Jul-06 R-38 R-39 R-40 R-41 R-42 R-43 R-44 DEP MONUMENTS SHORELINE CHANGE (FT) CLAM PASS FIGURE 8

between 1999 and 2006. In order to understand why there was such a significant loss in this area, it should be considered that the 1999 shoreline position was the post construction shoreline position after the beach fill was completed. The beach fill advanced the shoreline approximately 75 feet. The fill placed during that nourishment was relatively fine material from the flood shoal and interior channels, and the character of the material may have contributed to the relatively rapid loss, -53 feet of which occurred during the first year after placement. The shoreline at the next monument to the south followed a pattern similar to R- 42, with a nominal net shoreline advance of 2 feet between 1999 and 2006. The average shoreline position change for 2000 feet of shoreline north of the inlet between 1999 and 2006 was recession of -21 feet. For the same length of shoreline south of the inlet the average change was recession of -30 feet.

7. Conclusions and Recommendations The initial dredging of the flood shoals in 1999 and maintenance of the flood shoal channel in 2002 has resulted in significant improvement to the stability of Clam Pass. These improvements to the hydraulic stability of the inlet from the April 1999 dredging have persisted, however, the inlet channel and flood shoal areas have accumulated enough sand so that conditions are similar to those that existed prior to the maintenance dredging completed in January, 2002. Based on the July 2006 survey, there are approximately 12,000 cubic yards of sand within the currently permitted dredging limits. There are approximately 9,400 cubic yards in Segments B and C which were dredged in January 2002. This sand is expected to be beach quality. It has been nearly 5 years since the previous maintenance dredging. Although the tidal data show that flows through the inlet are still significantly stronger than the pre-1999 conditions, and may be sufficient to maintain flushing to the bay for the time being, there are indications that the flow through the inlet has diminished somewhat since the 2002 dredging. In order to reduce the potential for tidal exchange becoming diminished to the point where flushing might be inadequate, a Notice To Proceed to conduct another maintenance dredging has been obtained and dredging is scheduled to be conducted during 2007. Because of erosion along portions of the Clam Pass Park beach south of the inlet, County staff has recently considered the feasibility of obtaining additional sand for nourishment by expanding the dredging to include the inlet ebb shoal. This approach would provide immediate relief to the erosion problem on the park beach, however, it may also potentially have longer term consequences that should be carefully considered. A common impact from dredging significant portions of inlet ebb shoals is increased erosion of adjacent beaches. This occurs for several reasons including; interruption of natural transport which relies on the presence of an ebb shoal to bypass the inlet, diminished protection from waves for areas close to the shoal, and the readjustment of dredge cut slopes to a natural repose angle as the shoal begins to reform by trapping sand from the littoral system. A more detailed discussion of this is included in Section 10 below. In response to concern over the serious impacts that are likely to occur to the beach adjacent to the inlet from removal of the ebb shoal, and at the same time to provide some additional sand for nourishment of the eroded park beach, the entrance to the inlet will be dredged to the 80 feet width which was originally permitted and excavated during earlier maintenance prior to the 1999 improvements. This wider cut was not dredged in 1999 or in 2002, because it has been determined that 80 feet is significantly wider than the equilibrium channel width supported by tidal flow, and is therefore not necessary to achieve the improved flushing of Clam Bay. Furthermore, the wider cut quickly shoaled in with sand from the beaches immediately adjacent to the inlet. This 80 feet wide cut, however, does not have the potential for the level of serious impacts to adjacent beaches that should be expected from dredging the entire flood shoal, yet it will provide approximately 3,500 additional cubic yards of sand for nourishment. Additionally, careful observation of how the adjacent beaches respond to this relatively small increase in dredging scope may provide useful data regarding potential impacts from more aggressive dredging of the flood shoal.

The upcoming dredging event therefore includes dredging Station 0+00 through Station 18+00, with a dredge cut width of 80 feet at the entrance to the channel between Stations 0+00 and 3+00. It is recommended that the shoreline response to this dredging be considered in determining the appropriate dimensions for dredging the entrance channel in the future, because there has been no indication that dredging the entrance to dimensions much greater than the equilibrium section provides any benefit to extending the dredging interval. 8. Recommendations for Ongoing Monitoring. The tidal ranges and phase lags are important indicators of how well tidal flow through the inlet is flushing the bay system. This data is presented in Figures 6, 7, and 8. While these figures illustrate the improvements that have resulted from implementation of the Clam Bay Restoration and Management Plan, they also show that there is a significant amount of scatter in the data. As an extreme example, the most recent data shows the phase lag time at the Registry more than twice the average lag time over the time since the 1999 dredging. These inconsistencies have previously been treated as random scatter in the data because they have for the most part been relatively small in comparison to the overall flushing improvements. This random scatter might be related to factors such as wind influence on tidal flow, or storm water outflow. However, the scatter makes it difficult to identify small changes that would occur in response to the gradual shoaling in the inlet and the interior channels. It is therefore recommended that the tidal data collection program be expanded to include data collection at two additional stations to provide a level of redundancy that would be helpful in understanding the variability that has been fairly consistent in the data for seven years. The Clam Bay Restoration and Management Plan has so far been successful in maintaining a maintenance dredging interval of up to 5 years. This represents considerable cost savings over more frequent dredging, and this cost savings is considered justification for the additional data collection and analysis which may be used to improve management practices. With better understanding of how shoaling in the inlet influences the tidal parameters, it may be possible in the future to base scheduling of maintenance dredging on tidal measurements alone, and thereby reduce frequency and the cost of surveys for monitoring shoaling in the inlet. 9. Previous Recommendations. Recommendations made in previous reports that are still considered relevant to long term management are updated in this section. The long-term management of the Clam Pass inlet system should include continued monitoring of the inlet channel from the gulf to the interior, as well as the meandering connecting channels and along the dredge cut within the Clam Bay system. The July 2006 monitoring data show that cuts 1, 2, and 3 have remained relatively stable since the 1999 dredging. It is recommended that continued monitoring of these areas be conducted at four year intervals. This will reduce monitoring costs. However, there have been changes in the channel cross sections of the interior portion of cut 4 between Station 18+00 and 35+37 which demonstrate that this interior channel is a little more dynamic than cuts 1, 2, and 3. Most of the changes have been the result of readjustment of the dredge cut side slopes

resulting in a wider but shallower channel, with little change in net flow cross section. There has, however, been a more significant reduction of cross section, in comparison to the post 1999 dredging data, on three stations near the south end of cut 4, on stations 31+53 to 32+62. These are the three stations closest to and on the north side of the Clam Pass Park boardwalk bridge. The data show shoaling on these three stations north of the bridge, with an average cross section reduction in cross sectional area of approximately 35%. However, the cross sections at these stations remain approximately 175% greater than the pre-1999 dredging conditions. The recent shoaling in this area could therefore not be the cause of the recent large increase in phase lag measured at the Registry tide gage, and it must be concluded that the large increase in phase lag indicated for the Registry tide gage for 8/3/06 to 9/26/06 is erroneous. The shoaling on these stations has therefore not reached a condition that is critical to tidal flushing of outer Clam Bay, however, it is recommended that monitoring of the interior portions of cut 4 be continued on two year intervals. The tidal studies should be continued as an integral part of the annual monitoring because they will indicate when shoaling of the inlet and other channels has occurred to the extent where tidal circulation in the bay system is affected. (Recommendations regarding tidal studies are included in Section 8 above). Although dredging portions of the meandering channels between the four bays appears to have contributed to improving the flushing of Inner and Upper Clam Bay, the tidal exchange remains relatively low at the north end of the system. If biological studies indicate further enhancement to flushing of the remote northern portion of the bay system is necessary, that may be accomplished by straightening sections of the meandering channel which connect the bays. This approach would necessitate removing small areas of existing mangrove. Although this might be considered a negative impact to the mangrove community, this alternative could include restoration of mangroves within bypassed meandering sections of the channel, which in conjunction with the improved circulation to the mangrove wetland may constitute a net environmental benefit to the broader goal of managing the ecology of the overall bay system that would justify issuance of the required regulatory approvals. 10. Comments on Coastal Planning & Engineering independent analysis of Clam Pass Impacts. A report of an independent evaluation of dredging the Clam Pass ebb shoal was prepared in September 2006 by Coastal Planning and Engineering (CP&E) for the County. That report recommends mining the ebb shoal to obtain material for nourishment of Clam Pass Park Beach. The report concludes that implementation of the Clam Bay Restoration and Management Plan in 1999 disrupted natural north to south sand bypass of the inlet, which resulted in accumulation of sand on the beach north of the inlet and in the ebb shoal, and increased erosion of the beach south of the inlet. The process discussed in the CP&E report is that the Restoration and Management Plan dredging successfully increased the tidal prism, and the greater tidal energy on ebb flow has pushed sand further offshore where it has accumulated in the outer reaches of ebb shoal. This resulted in growth of the shoal, and sand trapped in the growing ebb shoal is a measure of a reduction in sand supply to the park beach.

This process as described in the CP&E report is one that may occur at inlets that are maintained by dredging, if the dredging actually increases the tidal prism. Monitoring data show that the Clam Pass tidal prism was increased by the 1999 dredging. However, there are site specific characteristics of Clam Pass that should be taken in to consideration before concluding that dredging the pass and erosion of the beach south of the inlet represent a direct cause and effect relationship. The CP&E report uses an empirical relationship to estimate the volume of sand that might be expected to be trapped by the growing ebb shoal. However, the empirical relationship is based on some rather broad assumptions, and an estimate based on the survey from September 2006 indicates that the ebb shoal actually contains a much smaller quantity of sand than the shoal volume predicted by empirical formula. Furthermore, based on recent accretion that has occurred south of the inlet, it is apparent that a significant amount of sand is already bypassing the inlet, which is an indication that the shoal is probably close to an equilibrium condition with respect to the tidal prism. Furthermore, what this empirical relationship says is that mining of all the sand from the ebb shoal will result in a condition which is much further from equilibrium than what exists now. In order to restore itself after such a mining operation, the shoal will accumulate sand at a higher rate and for a longer period of time, which would very likely result in a chronic erosion problem on both sides of the inlet. Review of historical data from the DEP Shoreline Change Atlas, plus more recent DEP survey data, seem to indicate some level of inlet effects on the downdrift beach. However, it is not clear from the recent monitoring data that the 1999 dredging has resulted in any significant increase in those effects. What should be a more important consideration is; to whatever extent the 1999 dredging may have affected the downdrift beach by trapping sand, an extensive mining of the ebb shoal will have a much greater impact. Increasing the scope of the shoal dredging does not seem to be an appropriate way to address the erosion problem. Summary Although inlet processes potentially impact the beach south of the inlet, the present maintenance plan for the inlet minimizes this potential by minimizing dredging of the ebb shoal. The changes that occurred during the 2005 to 2006 interval indicate that natural bypass is occurring. This does not necessarily mean that natural bypass is going to be sufficient to entirely address the erosion problem at the County Park beach, and additional nourishment may be necessary. However, removal of the Clam Pass ebb shoal should not be considered as the sand source for this nourishment because that would be trading one problem for another potentially more serious problem. A better solution would be to allow the natural bypass process to work and to supplement that process with nourishment form other sources as needed. The CP&E report does not address the issue of impacts from the proposed ebb shoal mining. Because of the potential impacts, it is doubtful that permits could be obtained for this proposal. It is recommended that if plans are ultimately developed for dredging the ebb shoal, those plans should include a contingency plan for addressing impacts that might occur from the dredging. It is likely that a contingency plan, including an approved sand source, would be a condition of the permit if such a permit is issued. It is not anticipated that dredging of the ebb shoal will have any adverse effect on the flushing of Clam Bay or on the mangrove communities in the Clam Bay system.

The erosion south of the inlet has been concentrated at R-43 approximately 1,000 feet south of the inlet. Since 1999 there has been very little net change in the park beach closer to the inlet at R-42, or further south at R-44. R-43, however, is in the vicinity of the park beach facility, and the erosion therefore creates a serious problem for the facilities and recreational value of the beach. This erosion hot spot is also evident in the historic data, and may be the result of wave refraction around nearshore contours. Erosion hot spots like this are fairly common adjacent to inlets because of wave refraction due to inlet shoals and tidal currents, and there is elevated hardbottom in the vicinity of the pass which might also contribute to the refraction patterns causing this localized erosion stress. Another alternative that could address this problem is an erosion control structure, such as a segmented breakwater. The use of erosion control structures may be a viable solution because of the localized nature of the problem and the high cost of nourishment if it is necessary to bring sand from a distant sand source.

11. References 1.) Agnoli, Barber, and Brundage, Inc. Beach Profile Monitoring Data at the Department of Environmental Protection Reference Monuments R-38 through R-44, 1999 to 2005. 2.) Coastal Planning and Engineering, Inc. Beach Profile Monitoring Data at the Department of Environmental Protection Reference Monuments R-38 through R-44, November, 2005. 3.) Johnson Engineering, Profile Monitoring Data at the Department of Envionmental Protection Reference Monuments R-38 through R-44, July 2006 4.) Johnson Engineering. Hydrographic Monitoring Data Collected at Cut #4 within the Clam Bay System, July 2006. 5.) Coastal Planning and Engineering Hydrographic Monitoring Data Collected at Cut #4 within the Clam Bay System, September 2005. 6.) 7.) Agnoli, Barber, and Brundage, Inc. Hydrographic Monitoring Data Collected at Cut #4 within the Clam Bay System, 1999 to 2004. 8.) Humiston and Moore Engineers, Project Area Photographs of South Naples Beach. 9.) Humiston and Moore Engineers, Clam Pass Restoration and Management Plan Bathymetric Monitoring Reports 1 through 6, 2000 2005. 10.) Pelican Bay Services District, Tide Data, 1999 2006. 11.) Florida Department of Environmental Protection Joint Coastal Permit No. 0128463-001-JC. 12.) Walton and Adams, Capacity of Inlet Outer Bars to Store Sand, Fourteenth Coastal Engineering Conference, Hawaii, July, 1976.

APPENDIX A DREDGE CUT 1 A-1 Aerial A-2 Cross Sectional Area Chart A-3 Cross Sectional Area Table A-4 Cross Sections (0+00 to 2+46) A-5 Cross Sections (3+43 to 6+59) A-6 Cross Sections (7+21 to 8+59)

180 160 140 120 100 80 60 40 20 0 CLAM BAY CUT #1 Area (ft2) Area (ft2) Area (ft2) Area (ft2) Area (ft2) Area (ft2) Pre Dredge March-99 Jul-00 Apr-02 May-04 Jul-06 400 +56.4-7.8% -1.3% +1.8-12.8% 300 200 100 0-100 -200 Pre Dredge -March-99 March-99 - Jul-00 Jul-00 - Apr-02 Apr-02 - May-04 May-04 - July-06 FIGURE: A-2 0+00 0+74 1+23 1+63 1+96 2+64 3+43 3+98 4+64 5+33 6+06 6+59 7+21 8+59 CROSS SECTIONAL AREA (SQ. FT) VOLUME CHANGE (SQ. FT)

Station Number Distance to Next Station Distance Average Pre Dredge March-99 Jul-00 Apr-02 May-04 Jul-06 Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) 0+00 74 37 43 1595 81 2979 88 3271 86.2 3190 83.6 3093 72 2646 0+74 49 62 21 1267 165 10135 91 5621 96.0 5902 - - 73 4483 1+23 40 45 25 1126 58 2590 67 2959 67.1 2986 59.5 2648 50 2232 1+63 33 37 48 1763 97 3530 96 3511 102.9 3756 87.0 3176 80 2916 1+96 68 51 29 1485 78 3939 75 3777 78.4 3958 83.2 4202 74 3751 2+64 79 74 29 2132 98 7225 93 6858 93.1 6843 99.5 7313 80 5906 3+43 55 67 41 2734 75 5018 73 4878 69.0 4622 72.0 4824 62 4146 3+98 66 61 34 2069 69 4150 73 4392 70.1 4242 61.9 3745 65 3951 4+64 69 68 31 2120 77 5225 72 4853 69.0 4660 69.5 4691 55 3709 5+33 73 71 43 3067 77 5453 80 5694 80.6 5722 80.9 5744 74 5236 6+06 53 63 23 1436 66 4133 59 3742 54.9 3461 60.5 3812 55 3476 6+59 62 58 56.5 3249 93.8 5394 88 5060 82.6 4749 94.1 5411 82 4707 7+21 138 100 33.1 3310 58.4 5840 67.4 6740 67.1 6710 69.9 6990 64 6405 8+59-69 60 4140 96.3 6645 82.6 5699 78.4 5408 83.3 5748 77 5299 FIGURE: A-3

APPENDIX B B-1 Aerial B-2 Cross Sectional Area Chart B-3 Cross Sectional Area Table B-4 Cross Sections (0+00 to 2+66) B-5 Cross Sections (3+13 to 6+01) DREDGE CUT 2

180 160 140 120 100 80 60 40 20 0 CLAM BAY CUT #2 Area (ft2) Area (ft2) Area (ft2) Area (ft2) Area (ft2) Area (ft2) Pre Dredge March-99 Jul-00 Apr-02 May-04 Jun-06 +53.7 +3.1 +10.2-3.C9% 4.70% 140 120 100 80 60 40 20-20 -40-60 Pre Dredge -March-99 March-99 - Jul-00 Jul-00 - Apr-02 Apr-02 - May-04 May-04 - July 06 FIGURE: B-2 0+00 0+61 0+96 1+62 1+99 2+66 3+13 3+72 4+67 5+17 6+01 0 CROSS SECTIONAL AREA (SQ. FT) VOLUME CHANGE (SQ. FT)

Station Number Distance to Next Station Distance Average Pre Dredge March-99 Jul-00 Apr-02 May-04 Jun-06 Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) 0+00 61 31 31 930 78 2391 83 2541 73 2229 101 3071 119 3629 0+61 35 48 31 1488 81 3864 70 3341 90 4327 66 3168 78 3737 0+96 66 51 17 869 75 3762 65 3262 69 3486 67 3368 63 3172 1+62 37 52 66 3420 101 5207 108 5567 115 5934 107 5531 127 6551 1+99 67 52 22 1118 66 3442 69 3588 71 3691 64 3333 62 3221 2+66 47 57 25 1397 62 3511 67 3819 74 4198 76 4343 83 4716 3+13 59 53 37 1940 86 4574 88 4643 92 4871 85 4510 78 4111 3+72 95 77 77 5937 118 9063 141 10888 156 12004 148 11427 156 11975 4+67 50 73 35 2509 80 5793 86 6257 112 8096 102 7410 119 8634 5+17 84 67 32 2117 83 5528 77 5166 90 6040 91 6077 88 5869 6+01-42 46 1932 95 3986 88 3688 92 3865 102 4292 88 3679 FIGURE: B-3

APPENDIX C DREDGE CUT 3 C-1 Aerial C-2 Cross Sectional Area Chart C-3 Cross Sectional Area Table C-4 Cross Sections (0+00 to 2+95) C-5 Cross Sections (3+65 to 7+03) C-6 Cross Sections (7+54)

300 250 200 150 100 50 0 CLAM BAY CUT #3 Area (ft2) Area (ft2) Area (ft2) Area (ft2) Area (ft2) Area (ft2) Pre Dredge March-99 Jul-00 Apr-02 May-04 Jun-06 +43% -10.1% +10.5-2.2% 4.2% 200 150 100 50 0-50 -100 Pre Dredge -March-99 March-99 - Jul-00 Jul-00 - Apr-02 Apr-02 - May-04 May04 - Aug-06 FIGURE: C-2 0+00 0+53 1+46 2+09 2+70 2+95 3+65 4+19 4+92 5+38 6+05 7+03 7+54 CROSS SECTIONAL AREA (SQ. FT) VOLUME CHANGE (CY)

Station Number Distance to Next Station Distance Average Pre Dredge March-99 Jul-00 Apr-02 May-04 Jun-06 Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) 0+00 53 27 39 1044 97 2573 78 2062 90 2383 76 2001 57 1522 0+53 93 73 39 2840 75 5482 81 5942 91 6636 88 6395 116 8500 1+46 63 78 42 3284 84 6552 77 5975 90 6994 - - 91 7106 2+09 61 62 24 1500 69 4253 68 4197 81 5003 74 4557 80 4958 2+70 25 43 52 2253 86 3681 80 3431 84 3619 75 3212 28 1223 2+95 70 48 56 2665 88 4166 91 4332 97 4617 97 4584 96 4542 3+65 54 62 74 4563 117 7266 105 6516 118 7294 100 6194 111 6884 4+19 73 64 51 3232 93 5925 68 4331 102 6470 103 6509 105 6645 4+92 46 60 46 2749 84 4986 70 4159 70 4178 75 4468 81 4843 5+38 67 57 166 9402 - - 174 9820 195 11006 183 10356 242 13647 6+05 98 83 41 3383 88 7252 72 5899 66 5478 72 5899 70 5759 7+03 51 75 52 3904 81 6012 68 5044 76 5639 91 6794 68 5041 7+54-26 53 1349 74 1884 74 1895 86 2206 - - 105 2687 FIGURE: C-3

APPENDIX D DREDGE CUT 4 D-1 Aerial D-2 Cross Sectional Area Chart (0+00 TO 7+10) D-3 Cross Sectional Area Chart (7+50 TO 18+28) D-4 Cross Sectional Area Chart (18+70 TO 35+37) D-5 Cross Sectional Area Table D-6 Cross Sections (0+00 to 0+50) D-7 Cross Sections (0+75 to 1+25) D-8 Cross Sections (1+50 to 2+00) D-9 Cross Sections (2+37.5 to 3+64.5) D-10 Cross Sections (4+10 to 5+10) D-11 Cross Sections (5+60 to 6+60) D-12 Cross Sections (7+10 to 8+00) D-13 Cross Sections (8+50 to 9+50) D-14 Cross Sections (10+00 to 10+50) D-15 Cross Sections (11+00 to 12+00) D-16 Cross Sections (12+50 to 13+50) D-17 Cross Sections (14+00 to 15+00) D-18 Cross Sections (15+50 to 16+50) D-19 Cross Sections (17+00 to 18+00) D-20 Cross Sections (18+28 to 19+21) D-21 Cross Sections (20+82 to 22+20) D-22 Cross Sections (23+10 to 25+84) D-23 Cross Sections (26+39 to 29+13) D-24 Cross Sections (29+89 to 31+53) D-25 Cross Sections (32+04 to 34+23) D-26 Cross Sections (34+72 to 35+37) D-27 Inlet Volume Dredge and Cumulative Volume Dredge D-28 Cross Sections (3+65 to 7+03)

900 800 700 600 500 400 300 200 100 0 CLAM PASS CUT #4 (STA. 0+00 - STA. 7+10) Area (ft2) Area (ft2) Area (ft2) Area (ft2) Area (ft2) Jun-03 Nov-03 May-04 Jul-05 Jul_2006 29% -8% -20% 35% 900 700 500 300 100-100 -300-500 June-03 - Nov-03 (cy) Nov-03 - May-04 c(y) May-04 - July-05 c(y) May-05 - July-06 c(y) Area Change Area Change Area Change Area Change FIGURE: D-2 0+00 0+25 0+50 0+75 1+00 1+25 1+50 1+75 2+00 2+37.5 3+00 3+64.5 4+10 4+60 5+10 5+60 6+10 6+60 7+10 CROSS SECTIONAL AREA (SQ. FT) CROSS SECTIONAL AREA CHANGE (SQ. FT)

900 800 700 600 500 400 300 200 100 0 CLAM PASS CUT #4 (STA. 7+50 - STA. 18+00) Area (ft2) Area (ft2) Area (ft2) Area (ft2) Area (ft2) Jun-03 Nov-03 May-04 Jul-05 Jul_2006-4% -5% -10% -12% FIGURE: D-3 7+50 8+00 8+50 9+00 9+50 10+00 10+19 10+50 11+00 11+50 12+00 13+00 13+50 14+00 14+19 15+00 15+50 16+00 16+50 17+00 17+50 18+00 18+28 CROSS SECTIONAL AREA (SQ. FT) 900 700 500 300 100-100 -300-500 June-03 - Nov-03 (cy) Nov-03 - May-04 c(y) May-04 - July-05 c(y) May-05 - July-06 c(y) Area Change Area Change Area Change Area Change FT) CROSS SECTIONAL AREA CHANGE (SQ.

400 350 300 250 200 150 100 50 0 CLAM PASS CUT #4 (STA. 18+28 - STA. 35+37) Area (ft2) Area (ft2) Area (ft2) Area (ft2) Area (ft2) Jun-03 Nov-03 May-04 Jul-05 Jul_2006 0% +2% FIGURE: D-4 18+28 18+70 19+21 20+82 21+52 22+20 23+10 24+65 25+84 26+39 27+60 29+13 29+89 30+77 31+35 32+04 32+62 34+23 34+72 35+37 CROSS SECTIONAL AREA (SQ. FT) 900 700 500 300 100-100 -300-500 -3% -14% Ap-02 - June-03 (cy) June-03 - Nov-03 (cy) Nov-03 - May-04 c(y) May-04 - July-05 c(y) Area Change Area Change Area Change Area Change CRISS SECTIONAL AREA CHANGE (SQ. FT)

Station Number Distance to Next Station Distance Average Area (ft 2 ) Volume (ft 3 ) CUT #4 10/15/1998 4/22/1999 7/00 Aug-01 Apr-02 Jun-03 May-04 Jul-05 Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) Area (ft 2 ) Volume (ft 3 ) 0+00 25 13 117 1463 546 6825 207 2588 238 2975 408 5100 304 3798 322 4024 164 2050 838 10470 0+25 25 25 100 2500 529 13225 191 4775 225 5625 320 7988 303 7582 291 7270 136 3400 702 17561 0+50 25 25 84 2100 536 13400 191 4775 191 4775 261 6528 287 7164 232 5805 147 3675 602 15049 0+75 25 25 82 2050 508 12700 177 4425 133 3325 308 7707 104 2602 189 4735 124 3100 422 10540 1+00 25 25 74 1850 468 11700 151 3775 108 2700 303 7581 109 2724 76 1905 123 3075 292 7302 1+25 25 25 70 1750 472 11800 176 4400 125 3125 283 7064 100 2498 200 5008 141 3525 143 3580 1+50 25 25 88 2200 385 9625 188 4700 130 3250 241 6018 115 2872 211 5278 153 3825 140 3510 1+75 25 25 - - 301 7525 183 4575 143 3575 236 5903 230 5740 190 4748 149 3725 143 3569 2+00 38 31 129 4031 249 7781 182 5688 131 4094 271 8467 205 6418 194 6047 156 4875 115 3579 2+37.5 63 50 120 6000 264 13200 190 9500 171 8550 202 10121 112 5604 200 9985 200 10000 203 10127 3+00 65 64 62 3937 330 20955 145 9208 170 10795 209 13244 83 5276 204 12922 221 14034 193 12241 3+64.5 46 55 100 5500 246 13530 175 9625 209 11495 192 10547 189 10411 266 14652 196 10780 196 10788 4+10 50 48 59 2817 476 22729 219 10457 227 10839 542 25901 212 10147 324 15476 232 11078 196 9336 4+60 50 50 78 3900 658 32900 187 9350 230 11500 539 26956 160 7997 287 14360 193 9650 158 7895 5+10 50 50 73 3650 406 20300 203 10150 186 9300 308 15384 - - 238.4 11920 220 11000 140 7010 5+60 50 50 68 3400 215 10750 180 9000 200 10000 235 11769 157 7861 215 10765 232 11600 184 9177 6+10 50 50 64 3200 152 7600 186 9300 199 9950 213 10652 174 8705 229 11430 215 10750 120 5980 6+60 50 50 98 4910 107 5345 199 9960 218 10900 241 12035 - - 181 9050 281 14050 160-7+10 40 45 136 6134 151 6791 234 10548 242 10890 267 12019 231 10380 257 11583 306 13770 213 9599 7+50 50 45 139 6242 139 6233 - - 290 13050 310 13939 267 12037 356 16011 322 14490 255 11460 8+00 50 50 107 5325 283 14125 321 16030 294 14700 415 20760 296 14822 382 19115 197 9850 284 14197 8+50 50 50 119 5965 496 24820 382 19080 390 19500 575 28769 429 21470 466 23280 258 12900 318 15882 9+00 50 50 103 5135 502 25085 470 23490 408 20400 704 35223 539 26949 527 26325 509 25450 306 15309 9+50 50 50 96 4780 507 25355 481 24050 451 22550 782 39116 670 33484 629 31455 502 25100 375 18766 10+00 19 35 78 2684 538 18554 478 16488 483 16664 842 29040 710 24501 716 24716 457 15767 392 13525 10+19 31 25 75 1870 513 12833 - - - 745 18627 602 15046 516 12900 387 9675 286 7153 10+50 50 41 72 2924 503 20372 441 17848 467 18914 785 31776 621 25154 541 21927 396 16038 372 15082 11+00 50 50 76 3780 513 25625 433 21670 423 21150 699 34926 625 31227 580 29000 480 24000 384 19180 11+50 50 50 59 2960 581 29040 422 21110 377 18850 763 38155 666 33280 518 25880 372 18600 409 20429 12+00 50 50 64 3185 527 26345 353 17630 237 11850 900 45010 690 34496 649 32465 369 18450 546 27281 12+50 50 50 80 4005 423 21130 405 20265 259 12950 617 30833 - - 240-174 8700 210 10494 13+00 50 50 89 4460 202 10115 174 8705 157 7850 160 8024 - - 223-310 15500 211 10549 13+50 50 50 67 3370 154 7715 134 6715 149 7450 905 45233 - - 164-174 8700 72 3593 14+00 19 35 84 2912 213 7335 231 7970 203 7004 701 24178 - - 257-310 10695 150 5182 14+19 81 50 131 6545 239 11935 - - - 675 33731 - - - - - - 145 7270 15+00 50 66 41 2712 494 32350 - - - 601 39358 676 44308 624 40872 232 15196 460 30142 15+50 50 50 21 1035 413 20645 - - 215 10750 564 28222 539 26928 300 15000 231 11550 359 17953 16+00 50 50 28 1405 467 23365 285 14270 234 11700 470 23479 535 26747 350 17500 278 13900 217 10841 16+50 50 50 25 1255 442 22090 286 14315 269 13450 279 13957 475 23753 305 15250 291 14550 154 7721 17+00 50 50 23 1130 380 19020 325 16225 250 12500 204 10183 549 27465 351 17550 203 10150 200 10023 17+50 50 50 25 1260 308 15420 272 13595 267 13350 198 9894 512 25624 370 18500 344 17200 118 5909 18+00 28 39 34 1330 174 6774 252 9809 188 7332 216 8443 264 10284 251 9770 198 7722 167 6524 18+28 42 35 37 1306 155 5432 168 5891 195 6825 257 8999 204 7151 208 7273 183 6405 153 5346 18+70 51 47 35 1623 189 8765 166 7700 215 9998 221 10264 208 9692 - - 182 8463 150 6986 19+21 161 106 39 4176 189 19981 192 20363 209 22154 202 21359 225 23882 - - 201 21306 187 19794 20+82 70 116 86 9956 143 16540 225 25930 253 29222 207 23868 324 37414 258 29764 - - 202 23328 21+52 68 69 63 4326 165 11413 179 12351 211 14559 240 16575 199 13765 - - - - 180 12406 22+20 90 79 48 3800 158 12482 153 12048 178 14062 243 19226 186 14662 198 15666 206 16274 162 12835 23+10 155 123 44 5439 168 20605 163 19968 225 27563 222 27162 191 23433 191 23422 - - 223 27286 24+65 119 137 12 1658 138 18906 155 21235 209 28633 271 37148 205 28124 223 30496 213 29181 139 18997 25+84 55 87 1 87 148 12902 130 11327 208 18096 156 13552 217 18868 210 18305 205 17835 186 16173 26+39 121 88 - - 155 13631 131 11493 202 17776 154 13531 198 17452 201 17679 205 18040 - - 27+60 153 137 - - 183 25044 193 26414 279 38223 234 32099 242 33162 234 32085 213 29181 203 27766 29+13 76 115 - - 197 22499 152 17347 235 26908 173 19795 154 17654 - - 186 21297 191 21869 29+89 88 82 - - 141 11595 140 11447 217 17794 192 15762 151 12378 200 16416 176 14432 191 15660 30+77 58 73 10 752 178 13009 189 13797 303 22119 195 14235 223 16310 256 18673 239 17447 190 13839 31+53 69 64 42 2680 212 13468 174 11017 219 13907 206 13102 183 11623 217 13754 240 15240 146 9280 32+04 58 64 42 2680 183 11646 143 9081 200 12700 219 13907 197 12488 201 12789 195 12383 137 8725 32+62 161 110 88 9636 241 26433 183 20082 204 22338 166 18195 202 22099 197 21604 205 22448 134 14636 34+23 49 105 71 7455 138 14501 157 16475 193 20265 206 21665 203 21292 226 23762 220 23100 334 35099 34+72 65 57 72 4121 196 11172 214 12192 257 14649 219 12483 254 14457 225 12811 219 12483 193 10989 35+37-33 61 1979 152 4927 134 4365 172 5590 166 5400 170 5515 177 5749 172 5590 142 4626 Jul_2006 FIGURE: E-3

APPENDIX E BEACH PROFILES E-1 Aerial E-2 Reference Monument Plots (R-38 to R-41) E-3 Reference Monument Plots (R-42 to R-44) E-4 Shoreline Position Relative to DEP Monument l E-2 Shoreline Change June 05 July 06 E-2 Shoreline Change 1999 2006