Grove RT9E-2 Product Guide Features t ( USt) capacity 12,8 m - 48,8 m (42 ft - ft) five-section, full power boom 11 m -18 m (36 ft - 59 ft) offsettable bi-fold swingaway extension 8 m (26 ft) extension inserts Grove MEGAFORM boom Cummins 239 kw (320 hp) Tier IV, diesel engine
Features Extensions A 18 m (59 ft) offsettable bi-fold lattice swingaway extension and two 8 m (26 ft) inserts give the RT9E-2 a maximum tip height of 85 m (279 ft). A hydraulically offsettable bi-fold lattice swingaway is also available, and conveniently offsets from 0 to from the operator s cab. Cab The Full Vision cab on the RT9E-2 tilts up to 20 providing the operator additional comfort when working at long boom and extension lengths. CraneSTAR is an exclusive and innovative crane asset management system that helps improve your profitability and reduce costs by remotely monitoring critical crane data. Visit www.cranestar.com for more information. Boom The 48,8 m ( ft) five-section Full Power boom incorporates the U shaped MEGAFORM design, which eliminates stiffeners, thus reducing weight and increasing capacity. Removable outrigger boxes Removable front and rear outrigger boxes provide up to 8788 kg (19,374 lb) of weight reduction for easier transport. Includes the removable 18 kg (,000 lb) of counterweight, auxiliary hoist and rope, and the RT9E-2 can easily self-remove close to 29 000 kg (64,000 lb).
Contents Specifications 4 Dimensions and weights 7 Working range 8 Load charts 9 Working range with inserts 13 Load chart with inserts 14 Working range - luffing 16 Load charts - luffing extension 18 Load handling 25 Notes 26
Specifications Superstructure Cab Boom 12,8 m - 48,8 m (42 ft - ft) five-section, sequenced synchronized full power boom. Maximum tip height: 51,5 m (169 ft) Lattice extension 11 m - 18 m (36 ft - 59 ft) offsettable bifold lattice swingaway extension. Offsets, and. Stows alongside base boom section. Maximum tip height: 69,2 m (227 ft) *Optional lattice extension 11 m - 18 m (36 ft - 59 ft) hydraulically offsettable bifold lattice swingaway extension. Offsets from to. Stows alongside base boom section. Maximum tip height: 69,2 m (227 ft) tilt, full-vision, all-steel fabricated with acoustical lining and tinted safety glass throughout. Deluxe seat incorporates armrest-mounted hydraulic single-axis controllers. Tilt/telescoping steering wheel with various controls incorporated into the steering column. Other standard features include: hot water heater, cab circulating air fan, sliding side and rear windows, sliding skylight with electric wiper and sunscreen, electric windshield wash/wipe, fire extinquisher, seat belt, air conditioning, and dual cab mounted work light. Swing Two speed, (2) planetary swing drives with foot applied multi-disc wet brakes. Spring applied, hydraulically released swing brakes. 3 positive swing lock and two-position mechanical house lock, both operated from cab. Maximum speed: 2.5 rpm Counterweight *Optional lattice extension inserts 18 144 kg (,000 lb) of total counterweight. Hydraulically installed and removed. Two 8 m (26 ft) lattice extension inserts. Installs between the boom nose and bifold extension, nonstowable. Maximum tip height: 85 m (279 ft) Hydraulic system Boom nose Seven nylatron sheaves mounted on heavy duty tapered roller bearings with removable pin-type rope guards. Quick reeving type boom nose. Removable auxiliary boom nose with removable pin type rope guard. Boom elevation Six main pumps with a combined capacity of 776 LPM (205 GPM). Maximum operating pressure: 331 bar ( psi). Two individual post pressure compensated valve banks. Return line type filter with full flow by-pass protection and service indicator. Replaceable cartridge with micron filtration rating of 5/12/16. 1230 L (325 gal) reservoir. Remote mounted oil cooler with thermostatically controlled hydraulic driven motor, fan/air to oil. System pressure test ports. Hoist specifications main and auxiliary hoist One double acting hydraulic cylinder with integral holding valve provides elevation from -3 to 78. Planetary reduction with automatic spring applied multi-disc brake. Grooved drum electronic hoist drum rotation indicator, and hoist drum cable followers. Load moment and anti-two block system Standard Graphic Display load moment and anti-two block system with audio-visual warning and control lever lockout. These systems provide electronic display of boom angle, length, radius, tip height, relative load moment, maximum permissible load, load indication and warning of impending two-block condition. The standard Work Area Definition System allows the operator to pre-select and define safe working areas. If the crane approaches the pre-set limits, audio-visual warnings aid the operator in avoiding job-site obstructions. 4 Maximum single line pull: 1st layer - 87 kg (19,267 lb) 3rd layer - 7432 kg (16,384 lb) 5th layer - 6464 kg (14,251 lb) Maximum permissible line pull: 7620 kg (16,0 lb) with 35 x 7 class rope Maximum single line speed: 171 m/min (562 fpm) *Denotes optional equipment
Specifications Superstructure continued Transmission Rope class: 35 x 7 EIPS WSC, Rotation Resistant Full powershift with 6 forward and 3 reverse speeds. Front axle disconnect for 4 x 2 travel. Rope diameter: 19 mm (3/4 in) Electrical system Rope length: Main hoist - 2 m (9 ft) Auxiliary hoist - 213 m (0 ft) Three12 V - maintenance free batteries. 12 V starting and lighting, circuit breakers. Maximum rope stowage: 368 m (6 ft) Drive 4x4 Carrier Chassis Steering Box section frame fabricated from high-strength, low alloy steel. Removable outrigger housings, front/rear towing and tie down lugs. Outrigger system Four hydraulic telescoping single-stage double box beam outriggers with inverted jacks and integral holding valves. Three position settings, 0%, % and fully extended. Outrigger boxes removable for ease of transportation. All steel fabricated, quick release type outrigger floats, 775 m (30.5 in) diameter. Maximum outrigger pad load - 75 298 kg (166,000 lb) Fully independent power steering: Front: Full hydraulic steering wheel controlled. Rear: Full hydraulic switch controlled. Provides infinite variations of four main steering modes: front only, rear only, crab and coordinated. Rear steer centered indicator light. Axles Front: Drive/steer with differential and planetary reduction hubs rigid mounted to frame. Rear: Drive/steer with differential and planetary reduction hubs pivot mounted to frame. Outrigger controls Oscillation lockouts Controls and crane level indicator located in cab. Automatic full hydraulic lockouts on rear axle permits 254 mm (10 in) oscillation with boom centered over the front. Engine (Tier IV) Cummins QSL8.9L diesel, six cylinder, turbo-charged with Cummins diesel particulate exhaust filter/muffler. Meets U.S. E.P.A. Tier IV and E.U. Stage IIIB. 239 kw (320 bhp) gross at 2200 rpm. Maximum torque: 1383 Nm (1020 ft lb) at 0 rpm. Fuel requirements: Maximum of 15 PPM sulphur content (Ultra low diesel fuel). Note: Tier IV engine required in North American and European Union countries. Engine (Tier III) Brakes Full hydraulic split circuit, dry disc service brakes operating on all wheels. Spring-applied, hydraulically released parking brake mounted on front axle. Tires Standard 33.25 x 29-38 bias ply. Cummins QSC8.3L diesel, six cylinders, 224 kw (300 bhp) (Gross) at 2200 rpm. Maximum torque: 1356 Nm (0 ft lb) at 0 rpm Fuel tank capacity Lights Full lighting including turn indicators, head, tail, brake and hazard warning lights. 379 L ( gal) Grove RT9E-2 5 *Denotes optional equipment
Specifications Carrier continued Maximum speed 24 km/h (15 mph) Gradeability (theoretical) 73% (Based on 79 4 kg [175,178 lb] GVW) 33.25 x 29 tires, pumps engaged, 48,8 m ( ft) boom, plus 18 m (59 ft) swingaway, 18 144 kg (,000 lb) counterweight, hookblock and headache ball. Miscellaneous standard equipment Full width aluminum fenders, full length aluminum decking, dual rear view mirrors, hook-block tie down, electronic back-up alarm, light package, front stowage well, tachometer/hourmeter, immersion type block heater, rear wheel position indicator, 36,000 BTU hot water cab heater, hoist mirrors, engine distress A/V warning system, front/rear tie down and tow lugs, coolant sight level indicator, hydraulic pump disconnect, LMI light bar. Hydraulically activated boom removal pins, lift cylinder travel support, USt hook block, 10 USt top swivel ball, CraneSTAR asset management system. *Optional equipment AUXILIARY LIGHTING AND CONVENIENCE PACKAGE: Includes superstructure mounted amber flashing light, dual base boom mounted floodlights, and rubber mat for stowage trough. USt hook block Rear pintle hook Cab controlled cross axle differential locks, (front and rear) PAT event recorder down load kit Wind speed indicator (wireless) Third wrap indicator with hoist cut-out (main and auxiliary) 6 *Denotes optional equipment
Dimensions and weights Dimensions Tire size A B C D E F G A B C D E F G 18 237 mm 18 847 mm 15 748 mm 14 884 mm 14 453 mm 11 9 mm 10 236 mm 13 9 mm 14 453 mm 10 973 mm 10 135 mm 9652 mm 69 mm 5918 mm (717.9") (742.0") (620.0") (585.9") (569.9") (4.9") (2.9") (5.0") (569.0") (432.0") (399.0") (3.0") (272.0") (232.9") 33.25 X 29 2 Wheel Steer 4 Wheel Steer Dimensions for table are represented in meters (inches). Conversions may not be exact. Ret 3556 mm (.0") Mid 20 mm (237.0") Full 8484 mm (334.0") All dimensions are in mm (in). 3797 mm (149.5") A 584 mm (22.9") C E Turn D Outside radius curb radius 3623 mm (142.6") fender width F Inside turn radius 24 G Inside curb radius R 4368 mm (R 171.9") Tail swing 12 5 mm (4.1 ") 259 mm (10.2") CL Rotation 4178 mm (164.5") 2614 mm (102.9") 17 568 mm (22.3") 554 mm (21.8") 428 mm (16.8") 5895 mm (232.1") 49 mm (194.5") 4426 mm (174.3") 77 mm (317.9") 182 mm (7.2") 2337 mm (92.0") 351 mm (13.8") 4427 mm (174.3") 9754 mm (384.0") Weights Weight of items removed Gross kg (lb) Front kg ( lb) Rear kg (lb) Basic Machine: Includes ft main boom, main hoist with 9 ft of wire rope and auxiliary hoist with 0 ft of wire rope, manual offsettable bifold swingaway, full counterweight, 10 USt headache ball, and USt hook block: 79 4 (175,178) 36 275 (79,971) 43 186 (95,207) Sub: Hydraulic offsettable bi-fold swingaway 79 736 (175,786) 36 6 (81,363) 42 830 (94,423) Remove:,000 lb counterweight, auxiliary hoist with rope, and manual offsettable swingaway 58 015 (127,899) 39 1 (87,744) 18 214 (,155) 21 734 (47,194) Remove:,000 lb counterweight, auxiliary hoist with rope, manual offsettable swingaway, USt hook block, 10 USt headache ball, and both outrigger boxes/beams 48 3 (106,8) 34 535 (76,136) 13 867 (30,572) 31 019 (68,385) Remove:,000 lb counterweight, auxiliary hoist with rope, both outrigger boxes/beams, USt hook block, 10 USt headache ball, and boom assembly 33 202 (73,196) 14 191 (31,285) 19 011 (41,911) 46 220 (101,897) Remove:,000 lb counterweight, auxiliary hoist with rope, both outrigger boxes/beams, USt hook block, 10 USt headache ball, boom assembly, and all tire/wheels 28 883 (63,676) 12 032 (26,525) 16 852 (37,151) 539 (111,417) 7 Grove RT9E-2
Working range ft main boom + 36 ft - 59 ft fixed offset extension 2 59' EXT. 230 220 210 36" EXT. 200 1 1 5 86 3 Boom and extension length in feet Height from the ground in feet 1 72 57 42 1 78 MAX BOOM ANGLE 30 20 10 0 200 1 1 1 30 20 10 AXIS OF ROTATION Operating radius in feet from axis of rotation 9' - 8" 11' - 0" 8 Dimensions are for largest Grove furnished hookblock and headache ball, with anti-two block activated. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
Load chart 42 ft - ft,000 lb % 27 ft 10 in spread 3 #0001 Feet Main boom length in feet 42 +2,000 224,000 176,000 (63.5) 127,0 97,300 (46) 76,0 (34) 10 12 15 20 25 30 35 57 147,000 (76.5) 147,000 147,000 125,0 (65.5) 95,5 () 75,2 (53.5),9 (46.5),300 (38.5) 42,0 (28) 72 *127,000 127,000,0 95,300 75,0,7, (52.5) 41,9 (47) 35,0 (41) 30,0 (34) 25,0 (24.5) 86 *92,0 86,5 78,0 68,0,,5 (.5) 42,3 (56.5) 35,8 (52.5) 30,5 (47.5) 26, (42.5) 22,0 (37) 19,200 (30.5) 16,0 (22) *65,000 62,6 (75) 56,0,0 (69) 44,0 38,9 34,6 30,0 25,8 (52) 22, (48) 18,9 (44) 16,200 (39) 13,0 (34) 11,6 (28) 97 (19.5) 44,0 44,0 44,0 41,0 () 37,4 (67.5) 33,4 30,000 (61.5) 26,9 (58.5) 23,0 20,0 (52.5) 18, (49) 15,0 (45.5) 13,5 (41.5) 11,0 (37) 10,000 (32) 84 (26.5) 56 (18.5) 43, 42,200 38,000 (73.5) 34, 31,3 29,200 26,3 (63.5) 23,8 21,0 (58.5) 19,2 16,0 (52.5) 15,000 (49.5) 13, (46.5) 11,4 (43) 99 (39.5) 8630 (35.5) 7320 (30.5) 6220 (25) 5 (17.5) 32,5 32,5 32,5 29,5 26,8 24,0 (67.5) 22,9 20,8 19,000 (.5) 17, 15,0 13,0 (53) 12,2 () 11,000 (47) 9730 (44) 84 (41) 73 (37.5) 62 (33.5) 53 (29.5) 4430 (24) 25 (16.5) Minimum boom angle ( ) for indicated length 25, 24,0 (76.5) 24,0 24,000 (72.5) 23,200 (.5) 21, 19,200 17,0 15,7 14,300 () 13, 12, 11,0 (53) 10,200 (.5) 20 (48) 8 (45.5) 71 (42.5) 62 (39.5) 53 (36) 45 (32.5) 37 (28) 23 Maximum boom length (ft) at boom angle 45 55 65 75 85 95 105 125 135 #LMI operating code. Refer to LMI manual for instructions. *This capacity is based upon maximum obtainable boom angle. +16 parts line required to lift this capacity (using aux. boom nose). Refer to Operator's and Safety Handbook for reeving diagram. Note: ( ) Boom angles are in degrees. Lifting capacities at zero degree boom angle Boom Angle 42 41,0 (35.3) Note: ( ) Reference radii in feet Grove RT9E-2 Main boom length in feet 57 24,6 (). 72 15,3 (64.6) 86 (79.3) 52 (94) 36 (108.6) 24 (123.3) 0 (138) A6-829-103576 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 9
Load chart ft 36 ft - 59 ft,000 lb % 27 ft 10 in spread 3 36 ft LENGTH Feet 25 30 35 45 55 65 75 85 95 105 #0021 #0022 #0023 *33,0 33,0 (76.5) 32,9 31,0 29,2 () 27,0 (67.5) 26, 24,7 (63) 23,5 (.5) 22,0 20, 18, (52.5) 16,000 () 14, (47) 12,0 (44) 11,0 (.5) 97 (37) 84 (33.5) 7430 (29) 63 (24) *23, 22, (76.5) 21,2 20,4 19,0 19,0 18,4 17,8 (62) 17,3 (59.5) 16,0 16,0 (54) 15,0 (51.5) 13,0 (48) 12, (45) 10,6 (41.5) 92 (37.5) (33) 68 (28) 17,2 16,8 16,0 16, (.5) 15,0 15,6 (65.5) 15,4 (63) 15,2 () 15, 15,0 (54) 14,000 (.5) 12,7 (47) 125 135 Min. boom angle for indicated length Max. boom length (ft) at boom angle ft 59 ft LENGTH #0041 *14,9 14,9 14,9 14,9 14,9 14,9 () 14,0 14,300 13,6 13, (62) 12,5 () 12,000 11,5 11, (53) 10,6 (51) 10,2 (48.5) 9930 (46) (43) 8.5) ( 72 (37) 63 (34) 55 (30.5) (26) 4 (21) 34 (14) #0042 12,3 11,0 (77) 11,0 (75) 11, 10,0 10,0 (69) 10,0 97 9510 92 () 30 (57.5) 8820 (55) 8620 (52.5) 84 (49.5) 82 (47) 7830 (43.5) 73 (.5) 64 (36.5) 5510 (32) #0043 9210 00 8820 (73.5) 86 84 (69) 83 82 8 (61.5) 79 (56) 79 (53) 7920 () 70 (46.5) 78 (42.5) NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J-765. 2. 36 ft boom extension may be used for single or double line lifting service. 59 ft boom extension may be used for single line lifting service only. WARNING: Lifting with the 36 ft extension base, with the 23 ft extension fly either erected or folded along side of extension base, is strictly prohibited. 3. Radii listed are for a fully extended boom with the boom extension erected. For main boom lengths less than fully extended, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is configured. For boom angles not shown, use the rating of the next lower boom angle. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. ft A6-829-102109 NOTE: () Boom angles are in degrees #LMI operating code. Refer to LMI for operating instructions *This capacity is based on maximum obtainable boom angle. 10 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart ft 36 ft - 59 ft,000 lb % 27 ft 10 in spread 3 #0021 23,3 23,3 (77) 23,3 (75) 23,3 (73.5) 23,3 23,3 22,300 (67.5) 20,3 18,3 16,0 (62) 15,0 () 13,0 (57.5) 12,4 11,300 (53.5) 10,300 (51) 93 (48.5) 85 (46) 77 (43.5) 68 (41) 59 (38) 51 (34.5) (31) 3730 (27.5) 30 (22.5) Feet 35 45 55 65 75 85 95 105 125 135 36 ft LENGTH #0022 #0023 *21,300 20,0 (76.5) 20, (75) 19,0 19,000 18,0 (69) 18,0 17, 15,5 (63) 14, 12,0 (58.5) 11,7 (56.5) 10,7 (54) 9810 (52) 89 (49.5) 8 (46.5) 73 (44) 65 (41) 5730 (37.5) 48 (34) 4 (30) 33 (25.5) 16,0 16,3 16, 15,8 15,6 () 15,0 15,300 14,0 (63.5) 13,2 (61.5) 12, 11,0 (56.5) 10,0 (54) 9200 (51.5) 83 (48.5) 70 (45.5) 68 (42.5) 155 165 1 Min. boom angle for indicated length Max. boom length (ft) at boom angle ft 59 ft LENGTH #0041 #0042 #0043 (63) 11,0 11,4 10,0 (57.5) 95 87 (53.5) 10 (51.5) 73 (49.5) 66 (47.5) 6 (45) 5530 (42.5) 48 () 42 (37.5) 36 (35) 30 (31.5) 25 (28.5) 20 (24.5) 11,0 11,300 (77) 10,9 (75) 10,0 (73.5) 10,0 10, () 9910 96 94 92 (63) 88 86 79 (54.5) 72 (52.5) 66 (.5) (48) 5510 (45.5) 49 (42.5) 43 () 37 (36.5) 3 (33) 24 (29) 89 87 86 8520 (72.5) 8410 (.5) 8300 8210 8 79 (.5) 7820 76 10 (53.5) 63 (.5) 57 (48) 51 (45) NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J-765. 2. 36 ft boom extension may be used for single or double line lifting service. 59 ft boom extension may be used for single line lifting service only. WARNING: Lifting with the 36 ft extension base, with the 23 ft extension fly either erected or folded along side of extension base, is strictly prohibited. 3. Radii listed are for a fully extended boom with the boom extension erected. For main boom lengths less than fully extended, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is configured. For boom angles not shown, use the rating of the next lower boom angle. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. ft A6-829-102127 NOTE: () Boom angles are in degrees #LMI operating code. Refer to LMI for operating instructions *This capacity is based on maximum obtainable boom angle. Grove RT9E-2 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 11
Load chart ft 36 ft - 59 ft,000 lb % 27 ft 10 in spread 3 Feet 45 55 65 75 85 95 105 125 135 155 165 1 36 ft LENGTH #0021 #0022 #0023 16,000 16,000 15,0 15,8 15,0 15,0 15,0 *15,200 (72.5) 15,7 15,000 14,7 (77) 14,9 14,300 14, 14,200 13,0 13,4 13,4 12,9 12,8 12,0 12,3 12,2 (.5) 11,0 11,7 11,0 (63) 10,6 11,200 11,200 9710 10,2 10,0 (59.5) 87 9310 96 (57.5) (63) 79 80 88 7210 76 10 (53.5) 65 00 72 (52) (55) 58 6310 65 (49.5) (53) (55) 5300 5710 59 (47.5) (51) (53) 4730 5 5330 (45.5) (49) (.5) 41 45 47 (43) (46.5) (48) 36 4220 (41) (44) (45.5) 30 30 36 (38.5) (41.5) (43) 24 29 (35.5) (38.5) 19 23 (32.5) (36) 14 10 (29.5) (32.5) 175 1 59 ft LENGTH #0041 #0042 #0043 10, 10, (77) 10, 10, 10, 10, 10, () 10, 10, 9710 (65.5) 92 88 8 73 (59.5) 6720 (57.5) (56) 5510 (54.5) 49 (52.5) 44 (.5) 39 (49) 35 (47) 3 (45) 2710 (43) 2300 (.5) 18 (38.5) 13 (36) 185 Min. boom angle for indicated length Max. boom length (ft) at boom angle 26 28 34 10,0 10,0 10,0 10,0 98 96 94 () 86 82 (65.5) 7920 73 6810 (.5) 6210 5620 5 45 (53.5) 4 (51.5) 36 (49.5) 32 (47.5) 2830 (45) 2420 (43) 2010 () 1530 (37.5) 35 80 80 80 8310 8220 (72.5) 8 7920 70 (67.5) 74 71 6630 (.5) 5520 (58.5) 49 (56.5) 44 (54.5) 39 (52) 3510 () 30 (47.5) 26 (45) 2220 (42) NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J-765. 2. 36 ft boom extension may be used for single or double line lifting service. 59 ft boom extension may be used for single line lifting service only. WARNING: Lifting with the 36 ft extension base, with the 23 ft extension fly either erected or folded along side of extension base, is strictly prohibited. 3. Radii listed are for a fully extended boom with the boom extension erected. For main boom lengths less than fully extended, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is configured. For boom angles not shown, use the rating of the next lower boom angle. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. A6-829-1019A NOTE: () Boom angles are in degrees #LMI operating code. Refer to LMI for operating instructions *This capacity is based on maximum obtainable boom angle. 12 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Working range ft main boom + 2 inserts + 36 ft - 59 ft fixed offset extension 2 2 59' EXT. 2 2 2 2 230 220 210 200 1 1 Boom and extension length in feet Height from the ground in feet 1 5 86 3 72 57 42 1 78 MAX BOOM ANGLE 30 20 10 0 2 2 230 220 210 200 1 1 1 30 20 10 Axis of Rotation Operating radius in feet from axis of rotation 9' - 8" 11' - 0" Grove RT9E-2 Dimensions are for largest Grove furnished hook block and headache ball, with anti-two block activated. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 13
Load chart ft 59 ft 26 ft or 52 ft,000 lb Insert % 27 ft 10 in spread 3 Feet 65 75 85 95 105 125 135 155 165 1 175 1 185 59 ft LENGTH WITH 26 ft INSERT 59 ft LENGTH WITH 52 ft INSERT #0084 #0085 #0086 #0084 #0085 #0086 (76.5) (75) (76.5) (72.5) 60 () (75) 60 (69) (73.5) (77) (76.5) 60 (67.5) (72.5) 60 (77) 6735 6545 6315 60 64 6230 (63.5) (67.5) 59 61 5955 (62) () (.5) 54 58 56 (.5) (65.5) 4930 5510 54 4 4195 (59.5) (63.5) (.5) 43 5 5200 3820 4 (65.5) (69) 30 4645 4910 33 3885 3785 (56.5) (65.5) 3420 4 4620 28 3610 35 (55) (59.5) () 3000 36 4 24 3205 3365 (63) (53.5) (.5) (58.5) 25 3230 36 20 20 3 (51.5) (56.5) (61.5) (63.5) 2210 2825 3220 16 25 2810 () (54.5) (57.5) (56) () 18 2420 27 2010 24 (48.5) (53) 1515 20 2385 1655 2075 (46.5) (51) (53.5) (57.5) (59.5) 10 19 16 (49.5) (51.5) 13 1625 (47.5) (49.5) Min. boom 45 angle for indicated length Max. boom length (ft) at boom angle 46 57 48 54 56 NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J-765. 2. 59 ft folding boom extension length may be used for single line lifting service only. Note: Lifting with the 36 ft extension base with either one or two 26 ft insert sections installed is not permitted. 3. For main boom lengths less than ft with the boom extension erected, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is set up. For boom angles not shown, use the rating of the next lower boom angle. 4. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 5. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 6. Capacities listed are with outriggers properly extended and vertical jacks set only. 56 57 A6-829-101983A NOTE: () Boom angles are in degrees #LMI operating code. Refer to LMI for operating instructions 14 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart 42 ft - 86 ft,000 lb Pick & Carry up to 2.5 mph Boom Centered over Front #06 Main boom length in feet Feet 42 61,7 61,7 49,000 (63.5) 34,7 34,7 (46) 29,2 (34) 23,0 (13) 10 12 15 20 25 30 35 45 57 34,0 34,0 (65.5) 34,0 () 28, (53.5) 22,3 (46.5) 17,7 (38.5) 14,000 (28) 10,9 (7.5) 55 72 86 28,300 22,0 17,0 (52.5) 13,9 (47) 10,0 (41) 8 (34) 58 (24.5) 24, 19,2 (.5) 15,200 (56.5) 11,8 (52.5) 20 (47.5) 60 (42.5) 4520 (37) 20 (30.5) 1 (22) 65 75 Min. boom angle for indicated length 0 Max. boom length (ft) at boom angle NOTES: 1. Capacities are in pounds and do not exceed 75% of tipping loads as determined by test in accordance with SAE J-765. 2. Capacities are applicable to machines equipped with 33.25x29 (38 ply) bias ply tires, at 85 psi cold inflation pressure. 3. Capacities appearing above the bold line are based on structural strength and tipping should not be relied upon as a capacity limitation. 4. Capacities are applicable only with machine on firm level surface. 5. On rubber lifting with boom extension not permitted. 6. Axle lockouts must be functioning when lifting on rubber. 7. For pick and carry operation, boom must be centered over front of machine, mechanical swing lock engaged and load restrained from swinging. When handling loads in the structural range with capacities close to maximum ratings, travel should be reduced to creep speeds. 8. All lifting depends on proper tire inflation, capacity and condition. Capacities must be reduced for lower tire inflation pressures. See lifting capacity chart for tire used. Damaged tires are hazardous to safe operation of crane. 9. Creep not over 200 ft of movement in any 30 minute period and not exceeding 1 mph. 20 72 NOTE: () Boom angles are in degrees #LMI operating code. Refer to LMI for operating instructions Lifting capacities at zero degree boom angle Boom angle 42 23,000 (35.3) 57 10,0 () A6-829-102108A Grove RT9E-2 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 15
Working range ft main boom + 36 ft - 59 ft luffing extension H [ft] 2 5 59' EXT. 230 220 210 200 1 1 Height from the ground in feet 5 76 3 Boom and extension length in feet 1 72 57 42 1 78 MAX. BOOM ANGLE 30 20 10 0 220 210 200 1 1 1 30 20 10 Axis of Rotation Operating radius in feet from axis of rotation Dimensions are for largest Grove furnished hook block and headache ball, with anti-two block activated. 9' - 8" 11' - 0" 16 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Working range ft main boom + 2 inserts + 36 ft - 59 ft luffing extension H [ft] 2 5 2 59' EXT. 2 2 2 2 230 220 Height from the ground in feet 200 1 1 1 5 Boom and extension length in feet 210 86 3 72 57 42 1 78 MAX. BOOM ANGLE 30 20 10 0 2 2 230 220 210 200 1 1 1 30 Operating radius in feet from axis of rotation 20 10 Axis of Rotation Dimensions are for largest Grove furnished hook block and headache ball, with anti-two block activated. 9' - 8" 11' - 0" Grove RT9E-2 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 17
Load chart 36 ft - 59 ft luffing folding boom extension (fixed angle) ft main boom ft 36 ft - 59 ft,000 lb % 27 ft 10 in spread 3 Feet 30 35 45 55 65 75 85 95 105 5 32,0 30,0 28,9 27,3 25,0 24,0 23,0 22,300 (62) 21,300 (59.5) 20, 18, (54.5) 16,000 (51.5) 14, (49) 12,0 (46) 11,0 (42.5) 97 (39) 84 (35.5) 70 (31) 6320 (26) 36 ft LENGTH 59 ft LENGTH 5 #0091 #0092 *23, 22, (76.5) 21,2 20,4 19,0 19,0 18,4 17,8 (62) 17,3 (59.5) 16,0 16,0 (54) 15,0 (51.5) 13,0 (48) 12, (45) 10,6 (41.5) 92 (37.5) (33) 68 (28) 15,2 14,8 14,0 14,200 (.5) 13,0 13,6 (65.5) 13,4 (63) 13,300 () 13, 13,0 (54) 13,000 (.5) 12,7 (47) 125 135 Min. boom angle for 5 indicated length Max. boom length (ft) at 5 boom angle ft 14,9 14,9 14,9 (73.5) 14,5 14, () 13,7 13,3 13,000 12,5 (61.5) 12,000 (59.5) 11,5 (57.5) 11, (55) 10,6 (52.5) 10,2 () 9930 (47.5) (45) 8 (42) 72 (39) 63 (35.5) 55 (32) (28) 4 (23) 3410 (16) 12,3 11,0 (77) 11,0 (75) 11, 10,0 10,0 (69) 10,0 97 9510 9,2 () 30 (57.5) 8820 (55) 8620 (52.5) 84 (49.5) 82 (47) 7820 (43.5) 73 (.5) 64 (36.5) 5510 (32) 5 78 76 (73.5) 74 73 (69) 7210 69 (61.5) 6830 (56) 67 (53) 67 () NOTES: 1. All capacities above the bold line are based on structural strength of boom extension. 2. 36 ft boom extension may be used for single or double line lifting service. 59 ft boom extension may be used for single line lifting service only. WARNING: Lifting with the 36 ft extension base, with the 23 ft extension fly either erected or folded along side of extension base, is strictly prohibited. 3. Radii listed are for a ft boom with the boom extension erected. For main boom lengths less than ft, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is configured. For boom angles not shown, use the rating of the next lower boom angle. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. ft NOTE: ( ) Boom angles are in degrees. A6-829-1025 #LMI operating code. Refer to LMI manual for operating instructions. *This capacity is based on maximum obtainable boom angle. 18 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart 36 ft - 59 ft luffing folding boom extension (fixed angle) ft main boom ft 36 ft - 59 ft,000 lb % 27 ft 10 in spread 3 Feet 45 55 65 75 85 95 105 125 135 155 165 1 36 ft LENGTH 59 ft LENGTH 5 5 #0091 #0092 *23,3 23,3 *21,300 * 23,3 20,0 (76.5) 23,3 20, 14,8 (72.5) (75) 23,3 19,0 14,5 11,0 (.5) 22,300 19,000 14,300 11,300 (77) 20,3 18,0 14,0 10,9 (69) (75) 18,3 18,0 13,8 10,0 78 () (73.5) 16,0 17,000 13,6 10,0 76 15,0 15,4 13,4 10, 75 (.5) (63) () 13,6 14,0 13,300 12,2 9910 7420 (58.5) (63.5) (72.5) 12,0 12,0 13, 11,0 96 7300 (56.5) (58.5) (61.5) (.5) 11,300 11,6 11,9 11,4 94 71 (54) (56.5) 10,300 10,6 10,9 10,0 9,2 (52) (54) (56.5) (63) 93 96 99 95 00 (49.5) (52) (54) 84 8810 87 80 6930 (47) (49.5) (51.5) (55) 7630 79 8200 10 85 68 (44.5) (46.5) (48.5) (53) (.5) 72 7430 73 78 6810 (41.5) (44) (45.5) (51) (54.5) 57 6510 66 66 7 67 (39) (41) (42.5) (49) (52.5) 49 56 6 6520 60 (35.5) (37.5) (46.5) (.5) (53.5) 41 48 5520 5910 62 (32) (34) (44) (48) (.5) 30 4 48 53 56 (28) (30) (42) (45.5) (48) 2820 33 4200 4820 (23.5) (25.5) (39) (42.5) (45) 35 42 (36.5) () 29 37 (33.5) (36.5) 2430 3 (30) (33) 18 24 (26) (29) Min. boom angle for indicated length Max. boom length (ft) at 5 boom angle ft NOTES: 1. All capacities above the bold line are based on structural strength of boom extension. 2. 36 ft boom extension may be used for single or double line lifting service. 59 ft boom extension may be used for single line lifting service only. WARNING: Lifting with the 36 ft extension base, with the 23 ft extension fly either erected or folded along side of extension base, is strictly prohibited. 3. Radii listed are for a ft boom with the boom extension erected. For main boom lengths less than ft, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is configured. For boom angles not shown, use the rating of the next lower boom angle. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. ft NOTE: ( ) Boom angles are in degrees. A6-829-102554 #LMI operating code. Refer to LMI manual for operating instructions. *This capacity is based on maximum obtainable boom angle. Grove RT9E-2 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 19
Load chart 36 ft - 59 ft luffing folding boom extension (fixed angle) ft main boom ft 36 ft - 59 ft,000 lb % 27 ft 10 in spread 3 Feet 55 65 75 85 95 105 125 135 155 165 1 175 1 185 36 ft LENGTH 5 #0091 15,5 15,5 15,5 14,9 15,5 14,9 *14,0 15,5 14,9 14, (77) 14,0 14,2 13,9 () 14, 13,5 13,0 13,0 12,0 12,0 12,0 12,2 12,200 (.5) 11,0 11,0 11,6 (63) 10,0 10,8 11, (61.5) 94 9910 10,200 (59.5) 85 89 93 (63) 77 8 8530 (56) 69 73 70 (54) 6320 66 69 (52) (55) 56 59 62 () (53) (55) 53 5630 (48) (51) (53) 40 47 10 (46) (49) (.5) 39 42 44 (43.5) (46.5) (48) 34 3730 30 (41.5) (44) (45.5) 29 32 (38.5) (41.5) 24 20 (36) (38.5) 19 2300 (33) (36) 0 10 (30) (32.5) 5 (77) (72.5) 95 9 8730 (63.5) 00 (62) 72 (.5) 6620 59 (57.5) 4830 (54) 43 (52) 38 () 3410 (48) 29 (46) 25 (44) 2210 (42) 10 (39.5) 13 (37.5) 59 ft LENGTH #0092 9420 () 10 8610 8220 (65.5) 78 71 6530 (.5) 5930 53 4820 4300 (53.5) 38 (51.5) 33 (49.5) 29 (47.5) 25 (45) 21 (43) 10 () 1420 (37.5) 7630 7510 73 72 7200 (72.5) 7 30 69 (67.5) 68 6830 6320 5820 (.5) 52 (58.5) 4710 (56.5) 4210 (54.5) 3710 (52) 32 () 27 (47.5) NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J765. 2. 36 ft boom extension may be used for single or double line lifting service. 59 ft boom extension may be used for single line lifting service only. WARNING: Lifting with the 36 ft extension base, with the 23 ft extension fly either erected or folded along side of extension base, is strictly prohibited. 3. Radii listed are for a ft boom with the boom extension erected. For main boom lengths less than ft, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is configured. For boom angles not shown, use the rating of the next lower boom angle. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. Min. boom angle for 29 34 36 26 indicated length Max. boom length (ft) at ft ft 5 boom angle NOTE: ( ) Boom angles are in degrees. A6-829-102558 #LMI operating code. Refer to LMI manual for operating instructions. *This capacity is based on maximum obtainable boom angle. 20 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart 59 ft luffing folding boom extension with 1 or 2 inserts (fixed angle) ft main boom ft 59 ft 26 ft - 52 ft,000 lb insert % 27 ft 10 in spread 3 Feet 75 85 95 105 125 135 155 165 1 175 1 59 ft LENGTH WITH 26 ft INSERT 5 #0095 6830 6830 (77) 6830 6830 6830 6830 60 (75) 6830 60 (.5) (73.5) (77) 6830 60 (72.5) 6830 60 65 6520 6310 63 6430 6230 5910 6 59 () 54 5810 56 (65.5) 4930 54 5430 43 5 51 (59.5) (65.5) 30 46 3420 4 4620 (56.5) (59.5) 3000 36 4 (55) (.5) 25 3230 36 (53.5) (56.5) 2210 2820 3220 (52) (54.5) (57.5) 18 2420 27 () (53) 1510 20 23 (48.5) (51) (53.5) 10 19 (49.5) (51.5) Min. boom 46 angle for indicated length 46 Max. boom length (ft) at 5 boom angle 57 ft 48 59 ft LENGTH WITH 52 ft INSERT 5 #1095 (76.5) (67.5) 4 3820 (63.5) 33 28 24 (59.5) 20 (58.5) 16 55 (76.5) (.5) 41 4 38 (65.5) 3610 3200 (63) 20 (61.5) 20 () 2010 16 (57.5) 56 (77) (.5) (69) 37 35 33 3 (63.5) 2810 24 20 (59.5) 16 NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J-765. 2. 59 ft folding boom extension length may be used for single line lifting service only. NOTE: Lifting with the 36 ft extension base with either one or two 26 ft insert sections installed is not permitted. 3. For main boom lengths less than ft with the boom extension erected, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is set up. For boom angles not shown, use the rating of the next lower boom angle. 4. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 5. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 6. Capacities listed are with outriggers properly extended and vertical jacks set only. 56 57 ft NOTE: ( ) Boom angles are in degrees. A6-829-102562 #LMI operating code. Refer to LMI manual for operating instructions. Grove RT9E-2 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 21
Load chart 36 ft - 59 ft luffing folding boom extension ft main boom (load luffing) ft 36 ft - 59 ft,000 lb 3 % 27 ft 10 in spread Feet 36 ft LENGTH 5 - - #0091 59 ft LENGTH 5 - - #0092 14,9 65 14,9 10,2 14,9 10,0 75 14,2 98 9320 13,5 96 89 85 12,0 94 80 5 12,2 92 82 49 95 11,0 9 79 48 10,0 89 7720 47 105 94 88 74 46 85 8720 7220 77 8 10 4520 69 73 67 44 125 6320 66 60 43 56 59 59 4310 135 53 42 40 47 4830 4200 39 42 43 4 34 3730 38 4 155 29 3410 38 24 29 33 165 19 25 29 1 0 2210 25 175 10 1 13 Min. boom angle for 29 indicated length Max. boom length (ft) at 5 boom angle ft 36 NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J-765. 2. 36 ft boom extension length may be used for single or double line lifting service. 59 ft boom extension may be used for single line lifting service only. WARNING: Lifting with the 36 ft extension base, with the 23 ft extension fly either erected or folded along side of extension base, is strictly prohibited. 3. Capacities are applicable for a ft main boom length only. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. The loads for luffing depend on the angle of the main boom, angle of the boom extension and dynamic working pressure of the luffing cylinder for the boom extension. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. ft A6-829-102575 #LMI operating code. Refer to LMI for operating instructions 22 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart 59 ft luffing folding boom extension with 1 or 2 inserts ft main boom (load luffing) ft 59 ft 26 ft - 52 ft,000 lb Insert 3 % 27 ft 10 in spread Feet 59 ft LENGTH with 26 ft INSERT 59 ft LENGTH with 52 ft INSERT 5 - - 5 - - #0095 #1095 85 95 4420 4330 105 42 6430 41 62 4 20 125 39 54 3920 135 4930 38 4 43 3810 3820 39 30 37 33 37 3420 3730 28 35 155 3000 36 24 3200 25 3230 20 20 165 2210 2820 16 20 1 18 2420 2010 175 1510 20 16 1 NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J-765. 2. 59 ft boom extension may be used for single line lifting service only. WARNING: Lifting with the 36 ft extension base, with either one or two 26 ft insert sections installed is not permitted. 3. Capacities are applicable for a ft main boom length only. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 4. The loads for luffing depend on the angle of the main boom, angle of the boom extension and dynamic working pressure of the luffing cylinder for the boom extension. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. 10 Min. boom angle for 46 indicated length Max. boom length (ft) at 5 boom angle 48 57 ft 56 56 57 ft #LMI operating code. Refer to LMI manual for operating A6-829-102579 instructions. Grove RT9E-2 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 23
Load chart Installation and removal of counterweight and auxiliary hoist rated lifting capacities in pounds On outriggers fully extended- 3 Radius in feet #01 Main boom length 42 ft* 10 48,000 12 48,000 15 48,000 20 48,000 25 48,000 30 48,000 Installation and removal of front and rear outrigger boxes rated lifting capacities in pounds without counterweight On rubber (stationary) - 3 Radius in feet #9810 Main boom length 42 ft* 10 11,0 12 11,0 15 11,0 20 11,0 * The boom must be fully retracted. Notes for on rubber Capacities are applicable to machines equipped with Titan 33.25 x 29 (38 ply) tires at 85 psi cold inflation pressure Capacities do not exceed 75% of tipping loads as determined by test in accordance with SAE J765. With no load, the boom angle must not be less than 35 when over sides of machine since loss of stability will occur causing a tipping condition. To lower boom below 35 boom angle, boom must be swung over front or rear and LMI bypass activated. Once one outrigger box is installed, do not swing load over that end of the machine while installing the other outrigger box. Each outrigger box assembly weighs 9373 lb including the outrigger beams and pads. May be used for single or double line lifting service. 24 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load handling Reeving diagram Weight reductions for load handling devices 36 ft - 59 ft manual boom extension *36 ft extension (erected) 52 *59 ft extension (erected) 98 Manual extension with 26 ft insert *59 ft extension (erected) 14, Manual extension with 52 ft insert *59 ft extension (erected) 19,0 36 ft - 59 ft luffing folding boom extension *36 ft extension (erected) 56 *59 ft extension (erected) 10,300 Luffing extension with 26 ft insert *59 ft extension (erected) 14,0 Luffing extension with 52 ft insert *59 ft extension (erected) 20,0 Line pulls and reeving information *Reduction of main boom capacities (no deduct required for stowed boom extension. When lifting over boom nose with 36 ft or 59 ft extension erected, the outriggers must be fully extended or % extended (19 ft 9 in) spread. When lifting over main boom nose with 26 ft or 52 ft insert erected, the outriggers must be fully extended. Auxiliary boom nose Hoists Cable specs Permissable line pulls Nominal cable length Main Model 35 19 mm (3/4 in) 6 x 37 class, EIPS, IWRC Special Flexible Min. Breaking Str. 58,0 lb 16,0 lb 9 ft Main Model 35 19 mm (3/4 in) 35 x 7 Class Rotation resistant (non-rotating) Min. breaking Str. 85,0 lb 16,0 lb 9 ft Auxiliary Model 35 19 mm (3/4 in) 35 x 7 Class Rotation resistant (non-rotating) Min. breaking Str. 85,0 lb 16,0 lb 0 ft The approximate weight of 3/4 in wire rope is 1.5 lb/ft Hoist performance Wire rope layer Hook blocks and headache balls USt, 5-sheave 0+ USt, 8-sheave 20+ 10 USt overhaul ball 6+ +Refer to rating plate for actual weight. When lifting over swingaway and/or jib combinations, deduct total weight of all load handling devices reeved over main boom nose directly from swingaway or jib capacity. NOTE: All load handling devices and boom attachments are considered part of the load and suitable allowances MUST BE MADE for their combined weights. Weights are for Grove furnished equipment. Hoist line pulls two-speed hoist Drum rope capacity (ft) Low available lb* High available lb* Layer Total 1 19,267 11,094 136 136 2 17,9 10,197 148 285 445 3 16,384 9434 4 15,243 8777 172 618 5 14,251 8206 184 2 6 13,3 75 196 998 * Max lifting capacity: 6 x 37 class and 35 x 7 class = 16,0 lb Working area diagram CENTERLINE OF BOOM 3 OVER SIDE CENTERLINE OF OUTRIGGER SUPPORT LONGITUDINAL CENTERLINE OF CRANE CG OF LOAD OVER FRONT OVER REAR OVER SIDE BOOM CENTERED OVER FRONT REAR AXLE OSCILLATION LOCKOUTS MUST BE SET TO MAINTAIN 3 CAPACITIES 6 12 SEE NOTE AT BOTTOM DIAGRAM FOR LIFTING ON OUTRIGGERS 3 CENTERLINE OF ROTATION FRONT DIAGRAM FOR LIFTING ON TIRES C6-829-003529 C6-829-009 Bold lines determine the limiting position of any load for operation within working areas indicated. Grove RT9E-2 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane 25
Notes 26
Notes 27 Grove RT9E-2
Manitowoc Cranes Regional headquarters Americas Manitowoc, Wisconsin, USA Tel: +1 920 684 6621 Fax: +1 920 683 6277 Europe, Middle East, Africa Ecully, France Tel: +33 (0)4 72 18 20 20 Fax: +33 (0)4 72 18 20 00 China Shanghai, China Tel: +86 21 6457 0066 Fax: +86 21 6457 4955 Greater Asia-Pacific Singapore Tel: +65 6264 1188 Fax: +65 6862 Shady Grove, Pennsylvania, USA Tel: +1 717 597 8121 Fax: +1 717 597 62 Regional offices Americas Brazil Alphaville Mexico Monterrey Chile Santiago Europe, Middle East, Africa Czech Republic Netvorice France Baudemont Cergy Decines Germany Langenfeld Hungary Budapest Italy Lainate Netherlands Breda Poland Warsaw Portugal Baltar Russia Moscow U.A.E. Dubai U.K. Buckingham 2011 Manitowoc Form No. RT9E-2 PG Part No. 11-006-2M-0911 China Beijing Chengdu Guangzhou Xian Greater Asia-Pacific Australia Adelaide Brisbane Melbourne Sydney India Calcutta Chennai Delhi Hyderabad Pune Korea Seoul Philippines Makati City Singapore Factories Brazil Alphaville China TaiAn Zhangjiagang France Charlieu Moulins Germany Wilhelmshaven India Pune Italy Niella Tanaro Portugal Baltar Fânzeres Slovakia Saris USA Manitowoc Port Washington Shady Grove This document is non-contractual. Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment, and price changes without notice. Illustrations shown may include optional equipment and accessories and may not include all standard equipment. www.manitowoc.com Powered by TCPDF (www.tcpdf.org)