ACCUFLO Conveyor Belt Cleaning System Page 1
Conveyor Belt Cleaning System - System Nomenclature CATGORY MAINFRAM INFORMATION BLAD INFORMATION CP=CONVYOR PRODUCTS CP - PA - 36 M - G 83 SYSTM TYP BLT WIDTH IN INCHS ASSMBLY INFORMATION M = Painted steel mainframe, stub ends and mounting brackets, dual spring tensioners and zinc plated mild steel hardware. S = Same as above except stainless steel mainframe, stub ends and mounting brackets. BLAD MATRIAL COD 83=83A STR 93=93A STR 90=90A THR 80=80A THR 69=69A STR 59=59A STR 58=58A THR BLAD MATRIAL COLOR G=GRN B=BLACK R=RD Y=YLLOW FM=FLAM RTARDANT MAROON FF=FLAM RTARDANT FORST GRN Notes: Safety chains and Nose Cone tensioner are an option and do not come standard on -Max V-Plows. All systems are specified in the actual required belt cleaning width. Systems are available to a maximum 72" in belt width. Stainless steel systems are available. Page 2
Sizing Chart Conveyor Belt Cleaning System Part Number "A" (belt width) ìbî Min. "B" Max. "C" (frame width) CP-PA16M-G83 16.00 22.00 34.00 40.00 CP-PA18M-G83 18.00 24.00 36.00 42.00 CP-PA20M-G83 20.00 26.00 38.00 44.00 CP-PA22M-G83 22.00 28.00 40.00 46.00 CP-PA24M-G83 24.00 30.00 42.00 48.00 CP-PA26M-G83 26.00 32.00 44.00 50.00 CP-PA28M-G83 28.00 34.00 46.00 52.00 CP-PA30M-G83 30.00 36.00 48.00 54.00 CP-PA32M-G83 32.00 38.00 50.00 56.00 CP-PA34M-G83 34.00 40.00 52.00 58.00 CP-PA36M-G83 36.00 42.00 54.00 60.00 CP-PA38M-G83 38.00 44.00 56.00 62.00 CP-PA40M-G83 40.00 46.00 58.00 64.00 CP-PA42M-G83 42.00 48.00 60.00 66.00 CP-PA44M-G83 44.00 50.00 62.00 68.00 CP-PA46M-G83 46.00 52.00 64.00 70.00 CP-PA48M-G83 48.00 54.00 66.00 72.00 CP-PA50M-G83 50.00 56.00 68.00 74.00 CP-PA52M-G83 52.00 58.00 70.00 76.00 CP-PA54M-G83 54.00 60.00 72.00 78.00 CP-PA56M-G83 56.00 62.00 74.00 80.00 CP-PA58M-G83 58.00 64.00 76.00 82.00 CP-PA60M-G83 60.00 66.00 78.00 84.00 CP-PA62M-G83 62.00 68.00 80.00 86.00 CP-PA64M-G83 64.00 70.00 82.00 88.00 CP-PA66M-G83 66.00 72.00 84.00 90.00 CP-PA68M-G83 68.00 74.00 86.00 92.00 CP-PA70M-G83 70.00 76.00 88.00 94.00 Cp-PA72M-G83 72.00 78.00 90.00 96.00 Page 3
Installation Guide Page 4
WARNING Always obey all applicable safety rules. Be sure all power to the conveyor has been disconnected and controls are locked out. Installation Tools Required - 90 Angle Gauge - 2 nd Wrench - Straight dge - Scribe or Chalk - Welder or Drill ASSMBLY BRAKDOWN Letter Part Number Quantity Description A CP-VP-N66-G83 1 Nose Cone B CP-DP-15"xx"-G83 2 Blade C CP-P-"xx"C 1 Mainframe D CP-MI-237C 2 Set Collar CP-P-C316 2 Mounting Bracket F CP-AR-5075 2 Square Head Set Screw,.5 x.75" G BOLT-0.5x2 -NC-ZINC varies Hex Bolt,.5" x 2" - Zinc Plated BOLT-0.5x2.5 -NC-ZINC 2 Hex Bolt,.5" x 2.5" - Zinc Plated H* CP-VP-SPRING 1 Front Spring Assembly I* 8947T18 2 Master Link 3/8" J* 3592T34 2 Safety Chain, 24" Notes: * = Optional items Page 5
Step One: Set Up The - is packaged for shipping with the mounting brackets packed in a separate box or wrapped and strapped to the pallet that your V-Plow was shipped on. Please make sure that you have two (2) of these brackets (item "" in the assembly breakdown) before continuing with this installation. Step Two: Layout Begin layout by cleaning any debris from the conveyor belt surface where you will be mounting the. Using a 90 degree layout tool, draw a line across the entire width of the belt perpendicular to the belt length (see L1 in figure 1). You may need to draw a partial line and then finish it with a straight edge. This line should be no further than 4 feet and no closer than 2 feet from the tail pulley in order to properly protect the pulley from tramp materials (see figure 2). If for some reason you can not mount the V-Plow within this area, you must then mount it to the closest available flat return idler, with the distance being no more than 1 foot from the idler. NOT: The further you place the V-Plow away from the tail pulley, the more likely your pulley will become susceptible to tramp materials. Figure 1 Step Three: Mounting Slide the mounting brackets onto the mainframeís pipe bar so that the flat side of the bracket faces the V-Plow. Place the complete V- Plow system on top of the belt surface. NOT: If the conveyorís chute walls prevent you from doing this because of the V-Plowís pipe bar welded to its frame, you may Figure 2 have to either cut holes through the chute walls to accommodate the pipe or cut the pipe ends to accommodate the width of the chute. As you set the V-Plow into place, be sure the blades are even with the belt edge or extend beyond the belt edge on both sides. Make sure the tails of the V- Plowís V-blade are even with the "L1" line you drew onto the belt in Step Two (see figure 1). Now slide the mounting brackets out till they make contact against the chute walls and rotate the brackets so the long end of the bracket is pointing up (see figure 2). At this point you can either weld or bolt the bracket to the side wall. If no chute wall or frame work is available you will need to construct an appropriate support structure. NOT: For Bolt In Only - Drill two m" diameter holes to accept w" diameter grade 8 bolts to mount each bracket into place. Anything less and you will void the warranty for this product. If welding, four stitch welds are sufficient to hold the bracket to the structure. Now loosen the set screws on the set collars and slide them out till they make contact with the mounting brackets and then tighten the set screws. Page 6
Step Four: Safety Devices (optional on -Max V-Plow Systems) Safety Chains and Nose Cone support hardware (items H, I & J on page 2) are optional items that can be purchased and installed to provide a greater level of safety for your personnel, conveyor system and -Max V- Plow. If these items are purchased but not installed properly, you will void any and all warranties associated with this V-Plow System. To install the Nose Cone support: (Only suggested for systems 36" and larger) Start by loosening the tensioner nut just above the spring located on the front of the V-Plow. Back it off by 4" or more (see figure 3). Next, weld a 32" x 32" x a" thick piece of angle iron (not provided) parallel to the V-Plowís mainframe across the chord members of your conveyor, approximately 11" above the beltís surface and directly above the hole in the nose cone support bracket (see figure 4). Now drill a w" diameter hole through the top of the angle iron directly above the hole located in the V-Plowís nose cone support bracket. Finally, remove the top nut and washer from the threaded rod and push the rod up through the hole in the angle iron. You will need to adjust both upper nuts on the rod until the lower welded nut is flush with the bottom of the nose cone support bracket. Figure 3 To install the Safety Chains: Weld or bolt the chain ends to the conveyor side walls approximately 6 to 8 inches in front of, and 2 to 4 inches above the V-Plowís mainframe (see figure 4). When properly installed, you should have approximately 3" of slack in each chain. NOT: Under no circumstances should the chains ever be installed as to be touching the belt in any fashion. NOT: Argonics recommends the use of safety chains on all V-Plow applications. Figure 4 Installation is now complete. Page 7