G, GP, G, GP In-line flow regulators (block form) Uni-directional Ø /... / inch, Ø 4... mm High flow performance In-line or panel mounting Adjustment can be locked aptive regulator needle will not blow out when unscrewed ickel plated brass components provide corrosion and contamination resistance and an extended life. Immediate quality sealing using silicone Technical features Medium: ompressed air Operating pressure: psi ( bar) max. Fluid/Ambient temperature: F to4 F (- to 6 ) Air supply must be dry enough to avoid ice formation at temperatures below F Tube size: /, /4, /6, /, / inch Release buttons in grey 4, 6,,, mm Release buttons in red Tubing types: ylon or Polyurethane, 9 or 9 durometer Materials Body: PBT Seals: BR (silicone free) u-packing and O-rings Release sleeve and backing ring: POM Grab-ring: stainless steel ollar: Z Options selector G Tube Inch Metric Option In-line mounting In-line and panel mounting P O/ tube size (inch) / /4 4 /6 / 6 / O/ tube size (mm) 4 4 6 6 / /US...
G, GP, G, GP Method of assembly. nsure that the end of the tube is cut square and is free from burrs.. Push the tube through the collet into the fitting.. 4 4. To disconnect push the tube into the fitting, hold down the collet and withdraw the tube.. ontinue pushing the tube through the O -ring until it bottoms on the tube stop then pull back. Impact resistant PBT body in black Release buttons are grey for inch, red for metric Stainless steel grab ring with special design to retain softer tube and provide easy releasability. 4 Silicon free U-packing provides leak tight tube seal under side loading. Technical data ø A T ø K Ø A (inch) Ø K (inch) T (inch) *) /.4,6 /4..64 /6.9. /.69.9 /..9 Ø A (mm) Ø K (mm) T (mm) *) 4. 6. 6. 4.... *) imensions here and in the individual tables refer to the collet being in the I position. *) imensions here and in the individual tables refer to the collet being in the I position. /US... /
G, GP, G, GP Speed controllers flowrate Ø /, Ø 4 mm 4 6 4 6 9 4 6 Ø /4, Ø 6 mm 4 6 9 4 4 6 Ø /6, Ø mm 4 6 9 6 4 4 6 Ø /, Ø mm 4 6 9 6 4 4 6 Ø /, Ø mm 6 4 6 9 4 6 / /US...
G, GP, G, GP In-line flow control øa øk Ø A B (inch) Ø K Weight Model (inch) (inch) (inch) min. max. (inch) (inch) (inch) (inch) (g) /.4.....6.44. G /4.6.9..6....69 G4 /6..9.4.66..9.9.9 4 G /.9.4..9...69.9 4 G6 /........ G In-line and panel mounting flow control Ø A B (mm) Ø K Weight Model (mm) (mm) (mm) min. max. (mm) (mm) (mm) (mm) (g) 4 4.. G4 6 6 9. 4.4.. G6 9.. 4 4.4 4 G 6 44 49 4.4. 4 G 6. 4.. 4.4.. G T øa B øk B Ø A B (inch) Ø K Panelhole T Panel Weight Model (inch) (inch) (inch) min. max. (inch) (inch) (inch) (inch) (mm) min. thickness (g) /.4.66.9...6.44..4. GP /4.6.9..9....69.6. GP4 /6...4.9..9.9.9 9.64. 6 GP /.9.4..4...69.9.. GP6 /..9.6..... 4.. GP Ø A B (mm) Ø K Panelhole Panel Weight Model (mm) (mm) (mm) min. max. (mm) (mm) (mm) (mm) (mm) min. thickness (g) 4 4..... GP4 6 6 49. 4 4. 4... 4. 6 GP6 9 6. 4 4. 9 6. 6 6 GP 6. 6. 4.... GP 6... 64. 4.4... 4. GP /US...4 /
G, GP, G, GP Warning These products are intended for use in industrial compressed air systems only. o not use these products where pressures and temperatures can exceed those listed under»technical features«. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult ORGR. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in pneumatic systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products. / /US...