STAINLE STEEL GRAND SERIES
STAINLE STEEL GRAND SERIES DEEPWELL SUBMERSIBLE PUMPS STAINLE STEEL - GRAND SERIES C.R.I. Always equips itself in advance to face the exponentially growing technological challenges across the industry and to gain high level of customer satisfaction. C.R.I. Introduced wide range of Stainless Steel-Grand Series Submersible Pumps to satisfy the increasing demand of both high flow and high head applications. These pumps are designed and developed using advanced technologies and integrated quality control programs backed by 5 years of profound experience which ensure low life cycle cost. These pumps are manufactured with highest levels of standardization and efficiency of use. This Stainless Steel Grand series pumps are available in 8, 1, 12 & 14 Nominal Diameters with a maximum flow upto 81 m³/h and maximum head upto 486 meters. These pumps are offered with complete Stainless steel construction to suit customers specific applications and aggressive water handling. Features : Best operating efficiency Precise parts made up of 316 Extremely hardwearing water lubricated bearings Highly durable & hygine Can be easily dismantled and repaired Can handle more upthrust loads Good resistance to sand and salt. Applications : Irrigation Civil Water Supply Industrial & Rural Water Supply Fire Fighting Pressure Boosting Units Sprinkler Systems Mining Oil & gas De-watering Food processing industries Golf course De-salination.
Model Identification Code MODEL IDENTIFICATION CODE DEEPWELL SUBMERSIBLE PUMP - 5 Hz S X X - XXX / XX X - X M Deepwell Submersible Pump Mining Application (This digit will be applicable only for the the pumps suitable for mining application) Nominal Pump Dia. in Inch Type of Materials of Construction (M.O.C) NT - Nominal Motor Dia. in Inch (This digit will be applicable only when the pump is suitable for lesser / higher dia motor) Chamber / NRV & SIC / Diffuser / Impeller / / / Impeller size (A-P) 3 Nominal Flow in m/h (Actual Value to be mentioned. Ex. 85 = 85m³/h, 65 = 65m³/h) Number of Impellers Pumped liquids Clean, thin, non-aggressive, non explosive, clear, cold, fresh water without abrasives, solid particles or fibre having the following characteristics. Maximum Temperature of Pumped Liquid a) Temperature 3 C (max.) b) Permissible amount of sand 7g/m3 (max.) c) Chlorides 675 ppm (max.) d) Allowable solids 3 ppm (max.) e) Specific gravity 1.4 (max.) f) Hardness (Drinking water ) 3 (max.) g) Viscosity 2 1mm/sec h) Turbidity 5 ppm silica scale(max.) i) ph 6 to 1 Motor 8"-14" Horizontal Minimum installation Vertical cooling flow installation minimum along the 3 angle motor.16 m/s 3 C 3 C Maximum operating pressure 8 Submersible pump 4.7Mpa (47 bar) 1 Submersible pump 4.9Mpa (49 bar) 12 Submersible pump 3.2Mpa (32 bar) 14 Submersible pump 2.Mpa (2 bar) Pump Operating Limitations 8 (15mm) 1 (25mm) 12 (3mm) 14 (35mm) Power Range in kw 4-11 13-185 45-25 75-3 Speed in rpm 29 29 29 29 192 39 54 81 lps 53 18 15 225 m 466 486 32 196 ft 1529 1594 15 643 5 6 7 9 Nominal diameter Max. Discharge Max. Head 3 m/h Outlet Size (BSP)
STAINLE STEEL GRAND SERIES Materials of Construction PART No. NOMINAL DIA. 8 NOMINAL DIA. 1 NOMINAL DIA. 12 NOMINAL DIA. 14 CHECK VALVE HOUSING CHECK VALVE DISC DIFFUSER CHAMBER IMPELLER JOURNAL BEARING VITON VITON PTFE PTFE BUSH WEAR RING SUCTION INTER CONNECTOR INLET SCREEN PUMP SHAFT CABLE GUARD COUPLING PART NAME Performance Curve Conditions The conditions below apply to the curves shown on the following pages. a. The Performance curves show pump performance at rated speed, voltage. b. The measurements were made with cold water (2 C) at atmospheric pressure (1bar). When pumping liquids with a density higher than that of water, motors with correspondingly higher outputs must be used. c. Pipe friction losses have not been included in the performance curves and performance tables. d. Q/H : The curves are inclusive of suction inter-connector losses at the actual speed. e. "Y- Curve" indicates the NRV loss to be considered while selecting pump. f. Efficiency curve : h % shows pump stage efficiency. g. Curve tolerance according to ISO : 996, Grade 3B. h. The performances are at rated voltage and are only Indicative. Actual discharge depends on availability of water in well, based on strength of water source, height of water column, submergence of pump, etc.,. i. The given performances are for specific materials of construction of pump. j. The outlet size of the pumps are as per BSP / GAS standard.
Group Performance Curves - 8", 1", 12" & 14" 5 29 rpm H - (m) H - ( ft ) 16 45 14 4 12 35 1 8 3 25 2 S14NT-6 S12NT-4 5 S12NT-325 2 S1NT-26 S1NT-19 1 S1NT-18 4 S8NT-13 15 S8NT-85 S8NT-15 S8NT-68 6 1 25 5 2 5 3 75 1 4 1 15 5 125 2 6 15 25 7 175 8 2 3 225 35 9 1 Q - (m³/h) Q - (lps) 25 4 Q - (US gpm)
STAINLE STEEL GRAND SERIES Cross Sectional Drawing 8" (2mm) 1" (25mm) Suction Inter Connector Inlet Screen Pump Shaft Wear Ring Impeller Coupling Cable Guard Check Valve Housing 32.5 Coupling Key Diffuser Chamber Check Valve Seat Bolt Bush Check Valve Spring Screw Journal Bearing Check Valve Disc
Cross Sectional Drawing 12" (3mm) 14" (35mm) 32.5 32.5 Suction Inter Connector Inlet Screen Pump Shaft Wear Ring Impeller Coupling Cable Guard Check Valve Housing 32.5 Coupling Key Diffuser Chamber Check Valve Seat Bolt Bush Check Valve Spring Screw Journal Bearing Check Valve Disc