SDGOG SDGLK Device mount with indirect component
2 Here you are: The special frosted finish of the device mounts in the SDGO series with a new visual impact The mixture of direct and indirect lighting is often perceived to be particularly pleasing. Experience the space in all of its dimensions. The SDT continuous light run with I.L.O also combines both possibilities in the OG variants. With its seamless integration in the SDT lighting run system, you have another design option for meeting the varying requirements of a lighting layout. New Individual.Lens.Optic with special frosted finish Direct/indirect diffuse light distribution System efficiency: up to 160 lm/w Lumen packages: 4000lm, 6000lm, 8000lm and 10000lm DALI variants SDGOG in the context of indirect lighting for LED device mounts ca. 0 % ca. 2 % ca. 5 % ca. 10 % ca. 16 %
Strong but indirect too 3 SDGOG device mounts with frosted optics The introduction of the Individual.Lens.Optic to continuous LED lighting runs LED also opens up the possibility of considering the indirect light component. A mixture of direct and indirect lighting is desirable when harmonious illumination is also required above the continuous light run. There are already various device mounts available in the standard SDT light run range for lighting layouts that exploit these possibilities. The SDGOG device mounts meets the wish for greater flexibility in this field. This can also become important during the renovation of lighting systems because the characteristics of the light distribution are close to those of T5/T8 systems. But by switching to LED you still benefit from the benchmark efficiency figures. With uniform LED spacing, even across the gap between circuit boards, the result is a sophisticated picture of modern lighting technology. Renovation solutions The optimisation of an existing lighting system is an important step in reducing electricity costs. Benchmark cost savings are guaranteed thanks to the LED technology with I.L.O. Of course, our compatibility list is no substitute for an individual lighting calculation. LED replaces T5/T8 Always top results: frosted translucent and transparent lens technology SDGLK In the continuous light run aesthetic, the indirect lighting component is enhanced with internal longitudinal prisms and a special frosted finish diffuser. This puts the SDGLK device mount out in front. It is recommended for applications where the priority is achieving a uniform, homogeneous appearance. SDGLK: diffuse light distribution and the highest indirect light component 5 years w arranty* lm (gross) lm/w 1) lm (net) lm/w 1) Ef fi c i e n c y SDG T5 1/35 3300 80 SDG T5 1/49 4300 81 SDGOG 4000 3900 160 +97% SDG T8 1/58 5200 90 SDGOG 4000 3900 160 +78% SDG T5 1/80 6150 69 SDGOG 6000 5400 152 +120% SDG T5 2/35 6600 83 SDGOG 6000 5400 152 +82% SDG T5 2/49 8600 83 SDGOG 8000 7300 144 +75% SDG T8 2/58 10400 90 SDGOG 8000 7300 144 +60% SDG T5 2/80 12300 71 SDGOG 10000 9100 137 +93% 1) Luminaire efficiency Please refer to the current data for LED luminaires under www.regiolux.de *For information about the manufacturer s guarantee for LED luminaires, see http://www.regiolux.de/fi leadmin/regiolux/service/garantie/warranty_led_en.pdf
4
Mounting rails 5 si1 IP 20/40/54 Housing: Mounting rail of roll-formed, torsionally stiff sheet steel, pregalvanised Suitable for IP20, IP40 and IP54 Flat ribbon cabling installed and wired on rapid mounting socket unit at the factory Miscellaneous: Special versions of device mounts or device mounts with light control components are needed to use the mounting rail wired with 11 poles A c c e s s o r i e s : To be equipped with either LED, T5 or T8 device mounts. Connection and assembly accessories as well as rail end caps and connectors to be ordered separately. Mounting instructions: The suspensions are designed for vertical loading For other arrangements or suspension spacing >2.5 m, approval and/or accessories are required Dimensions Type Unit LxBxH/DxH SDT1200/I 1200 1235 x 63 x 46 SDT1200/II 1200 2470 x 63 x 46 SDT1200/III 1200 3705 x 63 x 46 SDT1500/I 1500 1535 x 63 x 46 SDT1500/II 1500 3070 x 63 x 46 SDT1500/III 1500 4605 x 63 x 46 63 L 46 max. 2500 mm max. 2500 mm max. 2500 mm 1500/III 1500/III max. 20 kg max. 20 kg max. 20 kg Products Type Unit Wiring Colour /I /II /III Item number G Item number G Item number G SDT 1200 7x2,5 qmm vw 1828 1360 100 1,25 1828 2360 100 2,45 1828 3360 100 3,70 1500 5x1,5 qmm vw 1825 1580 100 1,60 1825 2580 100 3,20 1825 3580 100 4,60 wa 1825 1580 105 1,60 1825 2580 105 3,20 1825 3580 105 4,60 5x2,5 qmm vw 1826 1580 100 1,65 1826 2580 100 3,30 1826 3580 100 4,80 wa 1826 1580 105 1,65 1826 2580 105 3,30 1826 3580 105 4,80 7x2,5 qmm vw 1828 1580 100 1,75 1828 2580 100 3,50 1828 3580 100 5,20 7x2,5+4x1,5 qmm vw 1830 1580 100 1,92 1830 2580 100 3,73 1830 3580 100 5,80
6 Accessories mounting rail SDT IP20 SDTA F SDTA M SDT -K DV SDTE SDCS SDCSE KP KK SDH SDT -ZA SDT -AP RP SDRP SDCT SDD SDT -KL vw SDT -KL wa SDT -KT vw SDT -KT wa SDT -KX vw SDT -KX wa SDTV SDTVL In order to configure around corners as quickly as linear configurations, form components have been developed for the mounting rail system. Using L, T- and X nodes and flexible cabling sophisticated design plans such as grid or island solutions in the form of lighting landscapes can be quickly and easily realised.
7 Accessories Type Colour Material Details Item number V G Electrical technology Socket/plug combined SDTA F-7 ce Polymer 7pol., 5/7x1.5-2.5mm² for SDT 1820 3092 100 1 0,01 SDTA M-7 ce Polymer 7pol., 5/7x1.5-2.5mm² for SDT 1820 3090 100 1 0,01 SDTA F-11 ce Polymer 11pol., 4x1.5mm² + 7x1.5-2.5mm² for SDT 1820 2092 100 1 0,01 SDTA M-11 ce Polymer 11pol., 4x1.5mm² + 7x1.5-2.5mm² for SDT 1820 2090 100 1 0,01 Connection cable kit SDT -KDV vw St 2xmale+female 7 pol.; 7x2.5mm², 600mm for SDT 1884 7900 100 1 0,21 Protection Protective cover IP20 SDTE vw PC for SDT, ATS 1890 0231 100 2 0,02 wa PC for SDT 1890 0231 105 2 0,02 Mounting Single wire suspension SDCS ws Inox+mix l=2000mm for SDT 1890 0034 100 1 0,07 SDCSE ws Inox+mix Canopy D=123mm, rope D=1.5mm, L=2200mm, 3x1.5mm² 1890 0044 100 1 0,30 for SDT Chain suspension KK me St Chain l=30m, for SDT, SDT Basic, ATS, 9282 9300 100 1 4,60 suspended luminaires KP 80 me St+PC l=800mm for suspended luminaires 9282 9080 100 1 0,27 SDH me Inox for SDT, ATS at chain 1890 0039 100 1 0,04 SDT -AP me St for SDT 1890 0022 100 1 0,93 SDT -ZA me St for SDT 6820 9300 110 1 0,20 Tubular pendant RP 50 ws St+PC d=16mm, M13, l=500mm for suspended luminaires 9280 9050 100 1 0,25 suspension RP 80 ws St+PC d=16mm, M13, l=800mm for suspended luminaires 9280 9080 100 1 0,33 RP 100 ws St+PC d=16mm, M13, l=1000mm for suspended luminaires 9280 9100 100 1 0,40 SDRP me Inox+mix for SDT at tubular pendant RP 1890 0054 100 1 0,02 Mounting clip SDCT me Inox for SDT at visible T-rail 1890 0042 100 1 0,03 SDD me Inox for SDT at ceiling 1890 0033 100 1 0,01 Structure Mounting rail connector SDT -K L vw St L form 1884 7200 100 1 0,45 wa St L form 1884 7200 105 1 0,62 SDT -K T vw St T-form 1884 7300 100 1 0,84 wa St T-form 1884 7300 105 1 0,84 SDT -K X vw St X-form 1884 7400 100 1 0,63 wa St X-form 1884 7400 105 1 1,10 SDTV me St.galv. for SDT 1820 0020 100 1 0,22 SDTVL me St.galv. detachable for SDT 1820 0031 100 1 0,24 For mounting distance < 2500 mm: max. 2500 mm max. 2500 mm max. 2500 mm 1500/III 1500/III max. 20 kg max. 20 kg max. 20 kg For mounting distance > 2500 mm: max. 4500 SDTV.! 4600 ± 100 SDTV.! min. 2250 SDH SDT-ZA SDH 4500 1000 ± 200 (ca. 3600) >4600 SDTV.! SDT-AP max. 2250 max. 2250
8 Accessories mounting rail SDT IP54 SDTA F SDTA M SDTES SDCS SDCSE KK KP SDH SDT -ZA SDT -AP RP SDRP SDCT SDD SDTVLS For mounting distance > 2500 mm: max. 4500 SDTV.! 4600 ± 100 SDTV.! min. 2250 SDH SDT-ZA SDH 4500 1000 ± 200 (ca. 3600) >4600 SDTV.! SDT-AP max. 2250 max. 2250 Accessories Type Colour Material Details Item number V G Electrical technology Socket/plug combined SDTA F-7 ce Polymer 7pol., 5/7x1.5-2.5mm² for SDT 1820 3092 100 1 0,01 SDTA M-7 ce Polymer 7pol., 5/7x1.5-2.5mm² for SDT 1820 3090 100 1 0,01 SDTA F-11 ce Polymer 11pol., 4x1.5mm² + 7x1.5-2.5mm² for SDT 1820 2092 100 1 0,01 SDTA M-11 ce Polymer 11pol., 4x1.5mm² + 7x1.5-2.5mm² for SDT 1820 2090 100 1 0,01 Protection Protective cover IP54 SDTES vw PC for SDT IP54 1890 0235 100 2 0,02 Mounting Single wire suspension SDCS ws Inox+mix l=2000mm for SDT 1890 0034 100 1 0,07 SDCSE ws Inox+mix Canopy D=123mm, rope D=1.5mm, L=2200mm, 3x1.5mm² for SDT 1890 0044 100 1 0,30 Chain suspension KK me St Chain l=30m, for SDT, SDT Basic, ATS, suspended luminaires 9282 9300 100 1 4,60 KP 80 me St+PC l=800mm for suspended luminaires 9282 9080 100 1 0,27 SDH me Inox for SDT, ATS at chain 1890 0039 100 1 0,04 SDT -AP me St for SDT 1890 0022 100 1 0,93 SDT -ZA me St for SDT 6820 9300 110 1 0,20 Tubular pendant RP 50 ws St+PC d=16mm, M13, l=500mm for suspended luminaires 9280 9050 100 1 0,25 suspension RP 80 ws St+PC d=16mm, M13, l=800mm for suspended luminaires 9280 9080 100 1 0,33 RP 100 ws St+PC d=16mm, M13, l=1000mm for suspended luminaires 9280 9100 100 1 0,40 SDRP me Inox+mix for SDT at tubular pendant RP 1890 0054 100 1 0,02 Mounting clip SDCT me Inox for SDT at visible T-rail 1890 0042 100 1 0,03 SDD me Inox for SDT at ceiling 1890 0033 100 1 0,01 Structure Mounting rail connector SDTVLS me St.galv. detachable for SDT IP54 1820 0050 100 1 0,25
9
10 Device mounts IP20 Ts=fzi1 IP 20 Lighting technology SDGOG: Direct/indirect diffuse distribution using Individual.Lens.Optic made of frosted PMMA plastic Continuous optics Lamp: LED 50000h L80/B10 CRI 80 / 4000K Housing: Pre-galvanised sheet steel surface coated with polyester resin Installation without tools with two integrated snap-in catches Switching: 1 Control gear Electronic driver Fixed device mount plug with toolfree phase preselection and locating fi n g e r Miscellaneous: Other light colours, lighting technologies, luminous fluxes or emergency lighting on request SDGOG LED 4000 SDT SDGOG Dimensions Type Unit Versions LxBxH/DxH SDGOG 1500 LED 1531 x 55 x 37 Combination SDT+SDGOG/1500 LED 6000 840 55 63 67 37 η LB 100 % lm/w 152 direct/indirect 90/10 % UGR lat./long. 25,5/24,9 Products Type Unit Lamps PSys [W] Colour Ballast Item number G LED - Individual.Lens.Optic geeist direct/indirect diffuse distribution optically continuous IP 20 SDGOG 1500 LED 4000 840 26 vw ED 1857 0104 100 1,90 vw DALI 1857 0106 600 1,90 LED 6000 840 37 vw ED 1857 0204 100 1,90 vw DALI 1857 0206 600 1,90 LED 8000 840 53 vw ED 1857 0304 100 1,90 vw DALI 1857 0306 600 1,90 Replacement parts Type Colour Material Details Item number V G Electrical technology Contact pin SDG -Contact 1-Pol me St+mix for SDT 9200 0267 101 10 0,01
Device mounts IP20 11 Ts=fzi1 IP 20 Lighting technology SDGVOG: Direct/indirect diffuse distribution using Individual.Lens.Optic made of frosted PMMA plastic Continuous optics Lamp: LED 50000h L80/B10 CRI 80 / 4000K Housing: Pre-galvanised sheet steel surface coated with polyester resin Installation without tools with two integrated snap-in catches Variably positionable on the mounting rail Switching: 1 Control gear Electronic driver Variable device mount plug with tool-free phase preselection and locating finger Miscellaneous: Other light colours, lighting technologies, luminous fluxes or emergency lighting on request SDGVOG LED 8000 Dimensions Type Unit Versions LxBxH/DxH SDGVOG 1500 LED 1531 x 55 x 37 SDT SDGVOG Combination SDT+SDGVOG/1500 LED 8000 840 55 63 67 37 η LB 100 % lm/w 144 direct/indirect 90/10 % UGR lat./long. 26,5/25,9 Products Type Unit Lamps PSys [W] Colour Ballast Item number G LED - Individual.Lens.Optic geeist direct/indirect diffuse distribution optically continuous positioning variable IP 20 SDGVOG 1500 LED 8000 840 53 vw ED 1857 0304 150 2,00 vw DALI 1857 0306 650 2,00 LED 10000 840 70 vw ED 1857 0404 150 2,00 vw DALI 1857 0406 650 2,00 Replacement parts Type Colour Material Details Item number V G Electrical technology Contact pin SDG -Contact 1-Pol me St+mix for SDT 9200 0267 101 10 0,01
12 Device mounts IP54 Ts=fdzi1 IP 54 Lighting technology SDGSOG: Direct/indirect diffuse distribution using Individual.Lens.Optic made of frosted PMMA plastic Continuous optics Lamp: LED 50000h L80/B10 CRI 80 / 4000K Housing: Pre-galvanised sheet steel surface coated with polyester resin Installation without tools with two integrated snap-in catches With integrated seal to mounting rail and plastic seal to end faces Switching: 1 Control gear Electronic driver Fixed device mount plug with toolfree phase preselection and locating fi n g e r Miscellaneous: Other light colours, lighting technologies, luminous fluxes or emergency lighting on request SDGSOG LED 6000 Dimensions Type Unit Versions LxBxH/DxH SDGSOG 1500 LED 1531 x 55 x 37 SDT SDGSOG Combination SDT+SDGSOG/1500 LED 8000 840 55 63 67 37 η LB 100 % lm/w 144 direct/indirect 90/10 % UGR lat./long. 26,5/25,9 Products Type Unit Lamps PSys [W] Colour Ballast Item number G LED - Individual.Lens.Optic geeist direct/indirect diffuse distribution optically continuous IP 54 SDGSOG 1500 LED 6000 840 37 vw ED 1867 0204 100 1,90 vw DALI 1867 0206 600 1,90 LED 8000 840 53 vw ED 1867 0304 100 1,90 vw DALI 1867 0306 600 1,90 LED 10000 840 70 vw ED 1867 0404 100 1,90 vw DALI 1867 0406 600 1,90 Replacement parts Type Colour Material Details Item number V G Electrical technology Contact pin SDG -Contact 1-Pol me St+mix for SDT 9200 0267 101 10 0,01
13
14 Device mounts IP20 Tsfzi1 IP 20 Lighting technology SDGLK: Direct/indirect light distribution, frosted diffuser made of PMMA plastic with inner longitudinal prisms Optically seamless light run Homogeneous appearance Lamp: LED 50000h L80/B10 CRI 80 / 4000K Housing: Pre-galvanised sheet steel surface coated with polyester resin Installation without tools with two integrated swing handle latches Switching: 1 Control gear Electronic driver Fixed device mount plug with toolfree phase preselection and locating fi n g e r Miscellaneous: Other light colours, lighting technologies, luminous fluxes or emergency lighting on request SDGLK LED 4700 Dimensions N Type Unit Versions LxBxH/DxH SDGLK 1500 LED 1531 x 63 x 54 SDT SDGLK Combination SDT+SDGLK/1500 LED 7000 840 63 63 84 54 η LB 100 % lm/w 153 direct/indirect 84/16 % UGR lat./long. 25,2/23,8 Products Type Unit Lamps PSys [W] Colour Ballast Item number G LED - diffuser, frosted direct/indirect distribution optically continuous IP 20 SDGLK 1500 LED 5000 840 31 vw ED 1823 0304 100 2,00 vw DALI 1823 0306 600 2,00 LED 6000 840 37 vw ED 1823 0404 100 2,00 vw DALI 1823 0406 600 2,00 vw EM pack 3h 1823 0474 100 2,70 LED 7000 840 47 vw ED 1823 4504 100 2,00 vw DALI 1823 4506 600 2,00 Replacement parts Type Colour Material Details Item number V G Electrical technology Contact pin SDG -Contact 1-Pol me St+mix for SDT 9200 0267 101 10 0,01
Device mounts IP20 15 Tsfzi1 IP 20 Lighting technology SDGVLK: Direct/indirect light distribution, frosted diffuser made of PMMA plastic with inner longitudinal prisms Optically seamless light run Homogeneous appearance Lamp: LED 50000h L80/B10 CRI 80 / 4000K Housing: Pre-galvanised sheet steel surface coated with polyester resin Installation without tools with two integrated swing handle latches Variably positionable on the mounting rail Switching: 1 Control gear Electronic driver Variable device mount plug with tool-free phase preselection and locating finger Miscellaneous: Other light colours, lighting technologies, luminous fluxes or emergency lighting on request SDGVLK LED 10000 Dimensions Type Unit Versions LxBxH/DxH SDGVLK 1500 LED 1531 x 63 x 54 SDT SDGVLK Combination SDT+SDGVLK/1500 LED 10000 840 63 63 84 54 η LB 100 % lm/w 140 direct/indirect 84/16 % UGR lat./long. 26,4/25,0 Products Type Unit Lamps PSys [W] Colour Ballast Item number G LED - diffuser, frosted direct/indirect distribution optically continuous positioning variable IP 20 SDGVLK 1500 LED 10000 840 73 vw ED 1823 4604 150 2,00 vw DALI 1823 4606 650 2,00 Replacement parts Type Colour Material Details Item number V G Electrical technology Contact pin SDG -Contact 1-Pol me St+mix for SDT 9200 0267 101 10 0,01
9999 1541 217 1.A 1500 12/17 MA/PF Subject to changes Photo index Page 4 9 13 Bernd Ullrich, Kleinheubach DE WIKA, Klingenberg DE Christian Tech, Fulda DE Autohaus Herold, Heiligenstadt Ofr. DE Jake Campbell, Kiel DE Autohaus am Bungsberg, Oldenburg DE Regiolux Made in Germany Regiolux GmbH Hellinger Straße 3 D 97486 Königsberg T +49 9525 89 0 F +49 9525 89 7 info@regiolux.de www.regiolux.de