SVEA II GSM Connector User Manual

www.possio.com SVEA II GSM Connector User Manual

1. Introduction Before using SVEA II please read this manual carefully and keep it for future reference. SVEA II GSM Connector is a device for realization of voice connections from analog telephones, fax services and for internet access from PC and data transmission. All services are held over GSM network. Picture 1. SVEA II GSM Connector with external devices SVEA II GSM Connector package contains: SVEA II GSM Connector with built in battery Power supply Antenna GSM User Manual Picture 2. SVEA II GSM Connector package 2

2. Technical information 2.1. SVEA II GSM Connector specification GENERAL Dimension Weight excl. power supply 210 mm x 200 mm x 55 mm 1385 g ENVIRONMENT SPECIFICATION Operating temperature -10 o C - +55 o C Storage temperature -20 o C - +70 o C Relative humidity Max. 85% 2.2. - power supply Type Switch mode Input AC 100-240V AC, 50/60Hz Output VDC 18V DC Output current 0,8 A Weight 155 g 2.3. - internal antenna Antenna type All-around helical antenna Frequency band 870-960/1710-1880 MHz Impendance 50 ΩW Antenna gain 0,0 db VSWR < 2,0 Type of plug Direct for TNC-f 2.4. - battery backup Voltage Capacity Standby time on battery back up Conversation time on battery backup 12 V 2.3 Ah Min. 12 hours Min. 30 minutes 2.5. Technical specification SVEA II GSM Connector Voltage requirement Current consumption Current consumption (Standby) Telephone interface - Impedance - Line voltage - Ringing voltage - Dialing system - Max. quantities of user devices connected to the plug - Max. cable length between device and plug RJ11 11,0 20 VDC Max. 0.7 A @ 18.0 VDC 80 110mA 600 ΩW 48Vdc / nominal 52 VDC +/- 4 V 48 Vrms +/- 8 V @ 25/50 Hz DTMF / Pulse One device to one RJ11 plug 500 meter 3

Radio interface - Technology - Out power (According to: Release 99, V5) Data transmission Fax transmission Sensitivity of receiver Voice code - Siemens GSM Phase 2+ - Quad band: GSM 850/900/1800/1900MHz - Class 4 (+33dBm ±2dB) for EGSM900 - Class 1 (+30dBm ±2dB) for GSM1800 - Class E2 (+27dBm ± 3dB) for GSM 900 8-PSK - Class E2 (+26dBm +3/-4dB) for GSM 1800 8-PSK The values stated above are maximum limits and can be lower depending on connection. GPRS Multi-slot Class 12 Mobile Station Class B EGPRS Multi-slot Class 12 Mobile Station Class B CSD Group 3; Class 1 @ BER Class II < 2.4% E-GSM 900 min.: -102 dbm usually: -108 dbm GSM 1800 min.: -102 dbm usually: -107 dbm ETS06.10/(ETS 06.10) (Full rate), ETS06.50/06.60/06.80 (Enhanced Full Rate), ETS06.20/(ETS 06.20) (Half rate) and Adaptive Multi Rate AMR 3. General description 3.1. Cabinet External antenna cable hole USB Fax/Data Phone Power 1 2 3 4 Picture 3. SVEA II connectors 3.2. External devices plugs Power plug for power supply, which converts 220V/230V voltage to 18V voltage. Do not use other power supplies than the one that was originally supplied with SVEA II. Other power supplies can damage SVEA II. 1. TELEPHONE plug - RJ11 for analog telephone with DTMF or Pulse. 2. FAX/MODEM plug - RJ11 for analog fax machine G3 or analog modem V90. 3. RS232 port - for programming SVEA II GSM Connector only for authorized person. 4. USB port - not active. Contact Possio for more information. When you connect or disconnect power cable always hold the plug and not the cable. 4

3.3. LED signalization SVEA II GSM Connector has 3 built-in LEDs that show status of interface work. SIGNAL Color State GSM signal level Red Yellow Green Flashing Constant Flashing Constant Flashing Constant Very poor or out of GSM net RSSI < -85dBm Poor -85dBm =< RSSI < -80dBm Accepted -80dBm =< RSSI < -75dBm Medium -75dBm =< RSSI < -70dBm Good -70dBm =< RSSI < -65dBm Very good RSSI => -65dBm STATUS Color State Status Red Constant Terminal not on GSM network or SIM card error Green Constant Connected to network / terminal ready to use STATUS, TELEFON line Green Flashing (0.4s/0.4s) Connected to network Telephone line off hook Yellow Flashing (0.4s/0.4s) Telephone dial up to GSM network in progress Yellow Constant Conversation established STATUS, FAX/MODEM line Green/ /Yellow/ Flashing (0.4s/0.4s/0.4s/ Connected to network 0.4s) Fax/Data line off hook Yellow/Green Flashing (0.4s/0.4s) Data/Fax Dial up to GSM network in progress Yellow/Green Flashing (1.6s/0.4s) Data/Fax call established POWER Color State Type of power Green Constant Normal power Red Constant Battery power Red Flashing Battery power (Low battery) 5

4. Internal elements description 4.1. Internal elements Internal antenna GSM or wire for external antenna Battery backup PCB Picture 4. Elements of SVEA II GSM Connector 4.2. Alarm switch SVEA II has an alarm switch built into the PCB board that senses an unauthorized opening of the terminal. In case of unauthorized opening, SVEA II can send an alarm to Management Center with information about such an event. This information is also shown via LED signalization; POWER LED is flashing: green-yellow, if SVEA II is connected to power supply or red yellow when terminal is operating on battery backup. Cover must be fully closed for the unit to be operational. 4.3. Holes for mounting Picture 5. Holes for terminal mounting 4.4. Battery backup The battery backup is not connected at delivery. The battery should be connected during SVEA II installation. During the first start of SVEA II GSM Connector with battery backup, SVEA II should be connected to power supply for min. 48 hours. If there is a power break while SVEA II is working, the battery shall be recharged for min. 24 hours. In case of power failures, SVEA II will automatically switch to battery backup. A new battery should be used when standby and conversation time of battery backup is shortened (see: 2.4. - battery backup). Picture 6. Battery backup 6

Battery recycling The battery should not be disposed with unsorted household waste. Improper disposal may be harmful to the environment and human health. Please refer to your local waste authority for information on return and collection systems in your area. 4.5. Antenna Depending on the GSM signal level at installation site, a suitable antenna should be chosen to provide correct terminal functionality. SVEA II GSM Connector can work both with the internal and/or an external antenna. Internal antenna An internal helical GSM antenna is provided with terminal; See 2.3 for specification of this antenna. External antenna External GSM antenna for terminal shall fulfill requirements as below. Parameters of external antennas Parameters Type of antenna All-around and direction antenna with specification suitable for installation site Frequency band 880-960/1710-1880 MHz Impedance 50 ohm VSWR < 2,0 Type of connector TNC-f Recommended type of antenna cable H155, RLF-7 or other with the same or better spefication When you are using external antenna follow all rules of external antenna manufacturer. If you notice that the antenna or antenna cable is damaged, contact your reseller. Do not change the antenna or antenna cable by yourself. Do not touch the antenna or antenna cable if it is damaged. Avoid standing close to the antenna, when SVEA II is working. Keep a min. distance of 30cm. This distance can be different depending on antenna type. Picture 7. Example of mounting the external antenna For direction antennas with gain more than 3 db, see the safety distance below. Picture 8. Safe distance for antenna with gain 8 db and 20 db. 7

5. Installation and safety precautions 5.1. Place of installation SVEA II shall only be used inside buildings and cannot be exposed to humidity, sun or to high and low temperatures. SVEA II GSM Connector shall be installed at least 30cm / 12 inches from people. The distance between SVEA II and other devices connected to SVEA II shall be a minimum 3 meters. Space around terminal shall be free; terminal needs to be ventilated when working. Any heating devices (like radiator, stove) cannot be placed close to SVEA II. SVEA II shall be mounted with screws to mounting holes. SVEA II shall be mounted vertically on flat and hard surface. Picture 9. Example of SVEA II installation 5.2. Safety precautions Should an external antenna be used, please install the telephone cable away from the antenna cable. Do not dismantle and do not drop SVEA II. Battery backup is part of SVEA II. Do not dismantle the battery, because it contains materials that can cause burns to skin. Do not throw the battery into fire, because it can explode. Protect SVEA II against dust. Non-original antennas may have negative influence for RF signal transmission. Using the non-original antennas or connecting other devices can damage SVEA II. If terminal is repaired by a non-authorized person, SVEA II loses all warranty. Only the outside part of SVEA II cabinet can be cleaned. Use a dry and soft cloth only. Do not use cleaning alcohol, acetone, caustic chemicals, solvent, and any scrub powder, which can damage the plastic casing. 8

6. Calling 6.1. Voice services outgoing calls Telephone connected to TELEPHONE plug. 1. Pick up telephone handset, you will hear dial tone. If terminal is not ready you will hear a busy tone or a non-available tone. 2. Dial the number (DTMF/PULSE). If you press # the number will be sent to network immediately. Without pressing # number will be sent automatically after 7 seconds. 3. SVEA II sets the connection with defined number. 4. Hang up to end connection. 6.2. Voice services incoming calls Telephone connected to TELEPHONE plug. 1. After receiving information about incoming calls, terminal sends ringing tone to TELEPHONE plug. 2. Pick up telephone handset and start your conversation. 3. Hang up to end connection. 6.3. Additional services Telephone connected to TELEPHONE plug. 1. Pick up telephone handset, you will hear dial tone. If terminal is not ready you will hear a busy tone or a non-available tone. 2. Choose a code of additional service via DTMF. You cannot use PULSE mode for these services. 3. SVEA II receives service code from user and sends to network operator. 4. Hang up to end connection. 6.4. FAX services outgoing calls Fax connected to FAX/MODEM plug. 1. Sequence the same as in voice calls. 6.5. FAX services incoming calls Fax connected to FAX/MODEM plug, calls incoming on additional number for fax calls. It is recommended to set fax on automatic receiving mode. 1. After receiving information about incoming calls, SVEA II sends ringing tone to FAX/MODEM plug. 2. After answering the call, fax machine starts receiving the fax message. 6.6. Internet connection Dial-up Telephone modem connected to FAX/MODEM plug. 1. Choose (DTMF/PULSE) a number of ISP (Internet Service Provider). 2. Terminal sets the connection. 6.7. Data transmission outgoing calls Telephone modem connected to FAX/MODEM plug. 1. Pick up line to get a dial tone. 2. Choose a number (DTMF/PULSE) preceding 1*. If you press # the number will be sent to network immediately. Without pressing # number will be sent automatically after 7 seconds. 3. SVEA II sets the connection with defined number. 4. Hang up to end connection. 6.8. Data transmission incoming connections Telephone modem is connected to FAX/MODEM plug, calls incoming on additional number for data transmission. 1. After receiving information about incoming calls, SVEA II sends ringing tone to FAX/MODEM plug. 2. SVEA II sets the connection. For fax calls the minimum GSM signal shall be on medium level according to table in 3.3 SIGNAL LED. Realization of voice connection is not possible via FAX/MODEM connector. 9

7. Troubleshooting Problem with noise during connection Move connected devices away from SVEA II, and in case of using an external antenna move it also away at least 3 metres/ 10 feet from antenna and antenna cable. Problem with signal on line TELEPHONE and/or FAX/MODEM: Make sure that SVEA II is connected to power supply or battery backup (see 3.3 LED signalization). Make sure that signal level is strong enough (SIGNAL LED). Make sure that cables between terminal and connected devices are connected correctly and that they are not damaged. If device is connected to SVEA II correctly, make sure that SVEA II is reacting correctly for on Hook / Off Hook state (see 3.3 LED signalization). If SVEA II shows correct state but there is no signal (contact your operator). Problem with CLIP presentation: Make sure that telephone connected to SVEA II, services the FSK signalization standard. You can find this information in the user manual of analog telephone. Contact your operator, to find if CLIP FSK service is activated. Problem with additional services offered by operator: Contact your operator to find if additional service is activated for your SVEA II. Using the additional services is possible only via DTMF mode. Make sure that telephone connected to terminal is in DTMF mode. Problem with sending / receiving fax: Make sure that fax machine is connected to the FAX/MODEM plug. Contact your operator to find if sending/receiving fax message service (i.e CSD-fax ) is activated for your SVEA II and if you have an additional dedicated number for fax. Switch the fax machine to automatic mode and try once again to send /receive fax message. Make sure that SIGNAL LED shows correct GSM signal level recommended for realization of fax service. Problem with data transmission: Make sure that the modem is connected to FAX/MODEM plug. Contact your operator to find if data transmission service is active for your SVEA II and if you have additional number for data transmission. 8. Information about safety SVEA II GSM Connector uses the general GSM standard, like typical mobile phones. 8.1. Electronic equipment Although most of electronic equipment is well protected from RF signals, RF signals may interfere with some devices. In some cases the signal from SVEA II or external antenna, can interfere with medical equipment e.g. hearing aid. If you notice problems please read the instruction of your device. In case of using other medical equipment contact your doctor or manufacture of equipment, to make sure that your equipment is well protected from RF signals. 8.2. Usage Power cable and other cables connected to SVEA II shall always be installed in a proper way. Do not let children touch SVEA II and cables that are connected to terminal. If you notice that power cable is damaged, inform your reseller. Do not change the cable yourself. Non-original cable can caused damages to SVEA II. It can also be dangerous to the user. Recycling SVEA II should not be disposed with unsorted household waste. Improper disposal may be harmful to the environment and human health. Please refer to your local waste authority for information on return and collection systems in your area. 10