PRODUCTS CATALOGUE 2017 / 2018 10156 Torino - Strada Settimo 388/15 Tel (+39) 011.223.68.42 /43 Fax (+39) 011.223.67.67 info@ebarbero.com www.ebarbero.com
CATALOGO INDEX PRODOTTI 2017 / 2018 Pumps for LPG: - BGA: self-priming centrifugal pump for LPG - BGL: self-priming centrifugal pump for LPG - BGD: new self-priming pump for LPG Accessories for LPG: - VSG 20: By-pass valve - VFO 50: non-return valve Series SBF: pumping units with submersible motor pump for fuel delivery Series T / TFL: gear pumps for oils Special order pumps pag. 2 pag. 7 pag. 11 pag. 16 pag. 19 pag. 22 pag. 28 pag. 34 1
BGA SELF-PRIMING CENTRIFUGAL PUMPS FOR LPG An innovative design to ensure: Top safety Easy installation Easy maintenance
BGA SELF-PRIMING CENTRIFUGAL PUMPS FOR LPG Exclusive features of BGA series: Casings and elements with O-Ring seal for easy maintenance; Safety system against product s spil; Serie TFL ATEX certified: II 2G T4 Composed by several self-priming stages with a first centrifugal stage mounted at the suction end, BGA pumps perform an extremely low NPSH required valour and are suitable to handle liquids with entrained gases and especially for liquefied gases such as LPG.
BGA SELF-PRIMING CENTRIFUGAL PUMPS FOR LPG Construction and materials: Pump casing: Cast iron Centrifugal impeller: Special reinforced resin Self-priming impellers: Leaded brass Shaft: AISI 420 stainless steel Bearing: - Drive end: Ball bearing - Suction side: Graphite bushing Sealing: Double mechanical seal in oil bath Coupling: Aluminium alloy bell-housing and drive coupling for B5 motors Performance data at 1450 rpm Data refer to water - Tolerance 5% Compare BGA performance with those of the competitors! BGA pump grants higher pressure in all delivery range: from 10 to 20% more.
BGA SELF-PRIMING CENTRIFUGAL PUMPS FOR LPG Flanges dimensions according to UNI 2223 2229 PN 40
BGA SELF-PRIMING CENTRIFUGAL PUMPS FOR LPG Anti-spillage device 1. Oil reservoir 2. Plug with vent valve 3. Gauge 4. Pressure switch BGA pumps are equipped with a sealing system with double tandem mechanical seals with intermediate oil chamber, connected to an oil reservoir. The plug of the reservoir includes a special vent valve. In normal conditions, the reservoir is always at atmospheric pressure. In case of leak from the internal mechanical seal, the flow of liquid makes the vent valve to close putting under pressure the reservoir. This way, by means of a gauge and a pressure switch we can have an immediate detection of the problem without spillage of product. Pump can continue to work for a while giving the time to schedule the maintenance in order to restore initial safety conditions. Note: Gauge and pressure switch are excluded from supply.
BGL SELF-PRIMING CENTRIFUGAL PUMPS FOR LPG An innovative design to ensure: Top safety Top performances Easy maintenance
BGL SELF-PRIMING CENTRIFUGAL PUMPS FOR LPG Exclusive features of BGL series: Composed by several self-priming stages with a first centrifugal stage mounted at the suction end, BGL pumps perform an extremely low NPSH required valour and are suitable to handle liquids with entrained gases and especially for liquefied gases such as LPG. Casings and elements with O-Ring gaskets for perfect sealing and easy maintenance.
BGL SELF-PRIMING CENTRIFUGAL PUMPS FOR LPG Construction and materials: Pump casing: Cast iron Centrifugal impeller: Special reinforced resin Self-priming impellers: Leaded brass Shaft: AISI 420 stainless steel Bearing - Drive end: Ball bearing - Suction side: Graphite bushing Sealing: Mechanical seal Performance data at 1450 rpm: Data refer to water - Tolerance 5% NPSH (r) = Minimum positive head required for liquids in boiling conditions. Compare BGL performances with those of the competitors! BGL pump ensure more pressure in all delivery range: from 10 to 20% higher.
BGL SELF-PRIMING CENTRIFUGAL PUMPS FOR LPG Flanges dimensions according to UNI 2223-2229 PN 40
BGD NEW SELF-PRIMING PUMPS FOR LPG PATENTED An innovative design to guarantee: Top performance Top safety Easy maintenance
BGD NEW SELF-PRIMING PUMPS FOR LPG Exclusive features of BGD series: This pump is an absolute breakthrough in the field of self-priming LPG pumps. It is a multi-stage pump that operates according to a new principle. It consists of a set of side channel type stages with star impeller to which a special volumetric self-priming stage is connected on the suction side. The result is a pump with a much higher suction capacity than any other existing pump. In normal conditions, priming time is reduced by one third, thus eliminating downtimes in product delivery. In particular conditions, such as: > Crityical systems because of high suction gradient or with vertical tank; > Systems affected by periodic pumping problems due to climate or the product pumped. In all these cases, the BGD pump solves the problem, guaranteeing regular functioning. The highly-efficient volumetric self-priming stage guarantees fast, trouble-free suction of the gaseous phase of the product which is always present in the pipes at any start of the pump. So the pump does not require any external degassing device, thereby simplifying the system and reducing the related costs.
BGD NEW SELF-PRIMING PUMPS FOR LPG With regard to safety, the pump is fitted with an anti-spillage system that makes it possible to monitor any leak from the mechanical seal without product spillage, thereby eliminating one of the major risk of LPG plants. Another unique feature of this pump is that each element is sealed using O-Ring gaskets where other pumps adopt flat gaskets and sealing glue. The O-Ring guarantees perfect seal and, above all, fast, easy pump disassembly and re-assembly. This close coupled pump is fitted with bell housing and drive coupling which guarantees simple, safe connection to the electric motor. The motor pump is vibration-free and very silent with a sound level of less than 70 db. The pump has steel made, slip-on flanges DN 32 PN 40. ATEX Certification Ex II 2G T4
BGD NEW SELF-PRIMING PUMPS FOR LPG Performance data at 1450 rpm: Liquid LPG Specific Density 0,55 Kg/l (Tolerance +/- 2,5%) Flanges dimensions according to UNI 2223-2229 PN 40
BGD NEW SELF-PRIMING PUMPS FOR LPG Anti-spillage device 1. Oil reservoir 2. Plug with vent valve 3. Gauge 4. Pressure switch BGD pumps are equipped with a sealing system with double tandem mechanical seals with intermediate oil chamber, connected to an oil reservoir. The plug of the reservoir includes a special vent valve. In normal conditions, the reservoir is always at atmospheric pressure. In case of leak from the internal mechanical seal, the flow of liquid makes the vent valve to close putting under pressure the reservoir. This way, by means of a gauge and a pressure switch we can have an immediate detection of the problem without spillage of product. Pump can continue to work for a while giving the time to schedule the maintenance in order to restore initial safety conditions. Note: Gauge and pressure switch are excluded from supply.
VSG 20 BY-PASS VALVE FOR LPG Certification ATEX II 2G T4
VSG 20 BY-PASS VALVE FOR LPG Exclusive features of VSG 20 valve: The by-pass valve VSG 20 type is a multi purpose valve designed for use in LPG pumping systems. Installed on a LPG pump, the valve performs a double function: a) starting the pump, the valve enables the vapours to leak out from the pumping system; b) when the pump primes, the valve limits the maximum pressure of the pump. The valve has steel made flanges, sliding type, DN 20 PN 40 Operating limits: Temperature: -20 C / +60 C Maximun pressure: bar 40 Differential pressure range: min 10 / max 20 bar Max flow rate: 100 l/min
VSG 20 BY-PASS VALVE FOR LPG Valve VSG 20 construction: Sliding Flanges UNI 2223 2229 DN 20 PN 40
VFO 50 NON-RETURN VALVE FOR LPG Certification ATEX II 2G T4
VFO 50 NON-RETURN VALVE FOR LPG Exclusive features of VFO 50 valve: The VFO 50 non-return valve was designed for installation on BGL series pumps in LPG delivery systems. The valve is used to prevent the return of liquid from the suction pipe, ensuring that the pump is always primed. The valve has DN50 PN 40 coaxial connections. Operating limits: Temperature: - 20 C / + 60 C Maximum pressure: bar 40
VFO 50 NON-RETURN VALVE FOR LPG Valve VFO 50 construction: Flanges UNI 2223-2229 DN 50 - PN 40
series SBF PUMPING UNITS with submersible Motor Pumps for fuel delivery Indispensable in large service stations to take advantage of the delivery capacity of Multidispensers.
series SBF PUMPING UNITS with submersible Motor Pumps for fuel delivery Submersible Motor Pumps: Submersible motor pumps for fluel distribution system have been used for many years and their success is due to the advantages they undoubtedly offer compared to traditional systems. They represent the most rational solution to supply fuel dispenser and are indispensable in big, modern Service Stations. The Series SB/F Pumping Units are the result of a refined and innovative project that has led to significant product development and establishes a new standard in the field of submersible motor pumps for fuel. Detailed tests regarding performance and characteristics of the Motor Pump, the Discharge Head and the relative Leak Detector Valve VRF 4, confirm that the Series SB/F Pumping Units are unique in that each individual component is of the highest standard and, in some case, these are decidedly innovative.
series SBF PUMPING UNITS with submersible Motor Pumps for fuel delivery Exclusive features of submersible Motor Pumps: The Series SB/F is available in a range of three different capacities and performance levels, to meet the demands of modern Service Stations and fully exploit the delivery capacity of the new Multi-dispenser nozzles with vapour recovery. A robust stainless steel jacket houses the motor pump. The three-phase electric motor guarantees an excellent quality level and complies with the strictest safety regulations: Temperature T6 classification explosion-proof certificate (maximum surface temperature 85 ) Motor pump grounding conductor connected directly to the motor casing Thermal protector to stop the motor in case of overhating. Automatic restore when the temperature level falls. Sintered bronze depuration filter for motor bearing cooling liquid. THE RANGE
series SBF PUMPING UNITS with submersible Motor Pumps for fuel delivery Discharge head: The design of the head is strealine and rational, featuring unique constructive characteristics: ll caps have O-ring seals. The internal parts can be reached easily and quickly, seal is always perfect and maintenance times are drastically reduced. A large basket strainer protects head parts and all components situated downstream of the pump against impurities. This is obviously of great advantage to overall system management, where liquid impurities are one of the main causes of problems. The outlet is directed in a downward position and is equipped with a flange with O-ring seal. This system enables simple connection to underground piping, even in confined spaces, and guarantees problem-free seal. The equipment also copries a vent screw for a manual pressure relief, extremely useful to bleed to zero head and line pressure, preventing products during maintenance operations.
series SBF PUMPING UNITS with submersible Motor Pumps for fuel delivery Leak detector valve VRF 4: This is a piston valve designed to perform various functions, the most important of which is to signal any leaks from the delivery pipes. As regards this function, the valve is characterized by the test execution time, (less tha 5 sec) and the large internal capacity, capable of compensating the product's thermal volume changes. The valve also has a built in Venturi System in the cap together with the relative suction and discharge connections. The Venturi enables the valve to execute siphon priming in order to empty two or more tanks using the same pump. When the pump stops, the valve adjusts the head pressure for the Unit, limiting it approximately 0,7 bar, by means of the Venturi discharge. The valve also performs an effective air bleeding function. Each time the pump is activated, any air present in the discharge head is bled within a few seconds by means of the Venturi System discharge, thus ensuring delivery of a degassed product. Diagrammatic section with current flow
series SBF PUMPING UNITS 3 with submersible Motor Pumps for fuel delivery 1 7 4 5 2 6 1. O-ring seal cup 2. Check valve 3. O-ring seal cup 4. Strainer 5. 4 wire cable: line, ground 6. Vent screw 7. Leak detector Operating curves:
series T / TFL GEAR PUMPS FOR OILS A rational design that ensures: Robustness Reliability No servicing
series T / TFL GEAR PUMPS FOR OILS Exclusive features of gear pumps: T series gear pumps are positive-displacement self-priming pumps, suitable for conveying any type of clean and chemically non-aggressive liquid, as long as it has some lubricating properties. By choosing a suitable rotation speed, they can also be used for conveying highly viscous fluids. They have helical gears to ensure low noise and pulsation levels. Rational design and generous dimensioning of the parts make these pumps especially robust, reliable and free of servicing problems. Serie T Foot-mounted construction with bypass Serie T Foot-mounted construction with cover Serie TFL Close-coupled construction
series T / TFL GEAR PUMPS FOR OILS Rotation and flow direction: The arrow on the pump indicates both direction of rotation and flow. Looking the drive-shaft, direction of rotation is clockwise and flow goes from left (suction) to right (discharge). Anticlockwise rotation can be supplied on request. Relief-valve: To avoid dangerous over-pressures, pump can be equipped with an integral relief-valve of inside-recycling type or externalrelease type. The integral relief-valve must work occasionally and for short periods; when continuous pressure regulation is required, another relief-valve has to be installed on the delivery pipe.
series T / TFL GEAR PUMPS FOR OILS Nominal capacity Lt / min: type TFL type T
series T / TFL GEAR PUMPS FOR OILS Construction materials and limits:
series T / TFL GEAR PUMPS FOR OILS Performance data: type TFL type T Capacity data refer to oil 30 cst viscosity and are subject to 3% tolerance. Absorbed power data are valid up to 200 cst, beyond this value of viscosity they have to be properly increased. Installed power has to be at least 20% more then absorbed power.
SPECIAL-ORDER CATALOGO PUMPS PRODOTTI 2017 / 2018 A wide range of horizontal and vertical SELF-PRIMING and IMPELLER pumps can be produced upon request, according to the client s specific requirements. All pumps are constructed individually to order with the aim of meeting customer needs, and everything is perfectly traceable from the quotation, through implementation and up to testing.
10156 Torino - Strada Settimo 388/15 Tel (+39) 011.223.68.42 /43 Fax (+39) 011.223.67.67 info@ebarbero.com www.ebarbero.com