Material Safety Data Sheet SolEpoxy DK18-05 BLUE Revision 1 Issue date: 09/01/2010 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product type: Coating Powder Region: United States Company address: SolEpoxy, Inc. 211 Franklin Street Olean, New York 14760 Contact Information: Telephone: 716.372.6300 Emergency Telephone, ChemTrec: 800.424.9300 or 703.527.3887 E-mail: info@solepoxy.com Website: www.solepoxy.com 2. COMPOSITION/INFORMATION ON INGREDIENTS Hazardous components % ACGIH TLV OSHA PEL OTHER 30-60 30-60 0.1 mg/m³ TWA respirable fraction 5-10 5-10 1-5 0.5 mg/m³ TWA as Sb 0.5 mg/m³ TWA 0.5 mg/m³ TWA 0.5 mg/m³ TWA as Sb 3. HAZARDS IDENTIFICATION EMERGENCY OVERVIEW HMIS: Physical state: Powder HEALTH: 2* Color: Blue FLAMMABILITY: 1 Odor: Slight PHYSICAL HAZARD: 0 Personal Protection: See Section 8 WARNING: MAY CAUSE LUNG DAMAGE. CONTAINS MATERIAL WHICH MAY CAUSE CANCER. MAY CAUSE ALLERGIC SKIN AND RESPIRATORY REACTION. MAY CAUSE EYE, SKIN AND RESPIRATORY TRACT IRRITATION. Relevant routes of exposure: Skin, Inhalation, Eyes Potential Health Effects Inhalation: Skin contact: Eye contact: Ingestion: Existing conditions aggravated by exposure: Chronic exposure to respirable dust in excess of exposure limits can cause pneumoconiosis and can also increase the risks of developing respiratory cancer. May cause allergic respiratory reaction. Inhalation of dust generated by this material may cause respiratory tract irritation. May cause allergic skin reaction. May cause skin irritation with discomfort or rash. May cause irritation. Not expected under normal conditions of use. Eye, skin, and respiratory disorders. 1 of 5
See Section 11 for additional toxicological information. 4. FIRST AID MEASURES Inhalation: Skin contact: Eye contact: Ingestion: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention. Remove contaminated clothing and shoes. Immediately flush skin with plenty of water (using soap, if available). Get medical attention if symptoms develop and persist. Check for and remove any contact lenses. Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Get medical attention. DO NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. If individual is conscious, wash out mouth with water. Obtain medical attention. 5. FIRE-FIGHTING MEASURES Flash point: Autoignition temperature: Flammable/Explosive limits-lower %: Flammable/Explosive limits-upper %: Extinguishing media: Special fire fighting procedures: Unusual fire or explosion hazards: Hazardous combustion products: Product is a solid. Water spray (fog), foam, dry chemical or carbon dioxide. Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear. If mixed with air in sufficient amounts and proportions, organic dusts can form flammable or explosive dust/air mixtures. Oxides of carbon. s. Irritating organic fragments. Irritating organic vapors. Hydrogen bromide, Bromine. Phenolics. 6. ACCIDENTAL RELEASE MEASURES Environmental precautions: Clean-up methods: Prevent product from entering drains or open waters. Wear suitable protective clothing, gloves and eye/face protection. Sweep up spilled material. Avoid creating dust. 7. HANDLING AND STORAGE Handling: Storage: Use only with adequate ventilation. Wear suitable protective clothing, gloves and eye/face protection. Avoid contact with eyes, skin and clothing. Avoid breathing dust. Avoid any condition that will suspend or float powder particles in the air creating a dust cloud. Reduce all potential of static electrical discharge through bonding and grounding. Wash thoroughly after handling. Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use. Incompatible products: Refer to Section 10. For information on product shelf life contact SolEpoxy Customer Service at 1-716-372-6300. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering controls: Respiratory protection: Skin protection: Provide appropriate exhaust ventilation at machinery and at places where dust can be generated. Special ventilation procedures may be required to avoid explosion hazards if dust situation exists. Use local exhaust ventilation to maintain airborne concentrations below established exposure limits. Use NIOSH approved respirator if there is potential to exceed exposure limit(s). Chemical resistant, impermeable gloves. 2 of 5
Eye/face protection: Safety goggles or safety glasses with side shields. See Section 2 for exposure limits. 9. PHYSICAL AND CHEMICAL PROPERTIES Physical state: Powder Color: Blue Odor: Slight Vapor pressure: Not applicable ph: Not applicable Boiling point/range: Melting point/range: Specific gravity: 1.6 Vapor density: Evaporation rate: Solubility in water: Insoluble Partition coefficient (n-octanol/water): VOC content: 0%; 0 grams/liter (estimated) 10. STABILITY AND REACTIVITY Stability: Hazardous polymerization: Hazardous decomposition products: Incompatability: Conditions to avoid: Stable under normal conditions of storage and use. under normal processing. under normal use. Strong oxidizing agents. Storage with incompatible materials. Avoid creating dust. Dust may form explosive mixture in air. 11. TOXICOLOGICAL INFORMATION Carcinogen Status Hazardous components NTP Carcinogen IARC Carcinogen OSHA Carcinogen No Group 2B Yes Literature Referenced Target Organ & Other Health Effects Hazardous components Health Effects/Target Organs Allergen, Irritant Nuisance dust Irritant, Reproductive, Allergen Allergen, Respiratory Cardiac, Developmental, Eyes, Gastrointestinal, Irritant, Kidney, Liver, Lung, Mutagen, Nervous System, Reproductive, Sensory, Some evidence of carcinogenicity 3 of 5
12. ECOLOGICAL INFORMATION Ecological information: 13. DISPOSAL CONSIDERATIONS Information provided is for unused product only. Recommended method of disposal: EPA hazardous waste number: Dispose of according to Federal, State and local governmental regulations. Not a RCRA hazardous waste. 14. TRANSPORT INFORMATION The shipping classifications in this section are for non-bulk packaging only (unless otherwise specified). Shipping classification may be different for bulk packaging. U.S. Department of Transportation Ground (49 CFR): Hazard class or division: International Air Transportation (ICAO/IATA): Hazard class or division: WaterTransportation (IMO/IMDG): Hazard class or division: 15. REGULATORY INFORMATION United States Regulatory Information TSCA 8 (b) Inventory Status: All components are listed or are exempt from listing on the Toxic Substances Control Act Inventory. TSCA 12 (b) Export Notification: Tetrabrombisphenol A (CAS# ). CERCLA/SARA Section 302 EHS:. CERCLA/SARA Section 311/312: Immediate Health Hazard, Delayed Health Hazard CERCLA/SARA 313: This product contains the following toxic chemicals subject to the reporting requirements of section 313 of the Emergency Planning and Community Right-To-Know Act of 1986 (40 CFR 372). (CAS# ). This product contains the following "chemicals of concern" according to CERCLA/SARA - Section 313 (40 CFR 372.28) and has a Reporting Threshold of 100 lbs:. (CAS# ). California Proposition 65: This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. Canada Regulatory Information CEPA DSL/NDSL Status: WHMIS hazard class: One or more components are not listed on, and are not exempt from listing on either the Domestic Substances List or the Non-Domestic Substances List. Please contact SolEpoxy Customer Service for details. D.2.A, D.2.B 4 of 5
16. OTHER INFORMATION Revision notes: Prepared by: New issue MSDS Coordinator, SolEpoxy, Inc. 211 Franklin Street, Olean, NY 14760, U.S.A. 716.372.6300 DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. However, SolEpoxy, Inc. does not assume responsibility for any results obtained by persons over whose methods SolEpoxy, Inc. has no control. It is the user's responsibility to determine the suitability of SolEpoxy Inc.'s products or any production methods mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and persons against any hazards that may be involved in the handling and use of any of SolEpoxy, Inc.'s products. In light of the foregoing, SolEpoxy, Inc. specifically disclaims all warranties, express or implied, including warranties of merchantability and fitness for a particular purpose, arising from sale or use of SolEpoxy, Inc.'s products. SolEpoxy, Inc. further disclaims any liability for consequential or incidental damages of any kind, including lost profits. 5 of 5