RETNGULR ONNETORS FN360 Series FN-365P FN-365J FN-364P FN-364P FN-364J FN-364J FN-365P FN-365J FN-364P FN-364J FN-362J FN-363J FN-365P FN-367J FN-365P FN-364P FN-361P With type cover FN-365J FN-364P With type E cover FN-365P FN-364J With type J1 cover 1
Terms in Selection Table (Example) Structure Pin type Model ppearance ontact pitch Number of contacts Solder eyelet (tail shape) Wire-wrapping (post cross section) rimping (applicable WG No.) Straight, throughhole (P board hole dimensions) Right-angle, throughhole (P board hole dimensions) I (applicable WG No.) Gold Plating Silver Tin Operating temperature range Specification urrent rating Voltage rating ontact resistance Insulation resistance ( 500 V) ielectric withstanding voltage (for 1 minute) Insulation material cleaning with hlorothene (example) Remarks 700 series 2.54 2.54 10, 14, 16, 20, 26, 30, 34, 40, 50, 60 P J P J P J 0.64 φ 0.8, 2.54 2.54 φ 0.8, 2.54 2.54 #28, Flat cable #28, Flat cable 55 to +105 1 250 V 20 mω max. ( 6 V, 0.1 ) 1,000MΩ min. 500 V Polyester cleaning possible FN-705P050-U/M FN-707J050-U/ EMI protection cover provided ontact pitch enotes a pitch between adjacent contacts or pitch between rows. 2.54 mm (0.100 in.) (pitch between adjacent contacts) x 2.54 mm (0.100 in.) (pitch between rows) Number of contacts enotes the numbers of contacts of available connectors. onnection type enotes the connection type of the cable or P board connection section. Plating enotes the contact plating specification. Operating temperature range The connector can be used within the specified temperature range. urrent rating Maximum current that can flow through one connector pin Voltage rating Maximum voltage that can be applied to a connector ontact resistance Resistance observed at the contact part when 0.3 (or 0.1 ) flows at 6 V with the connectors mated Insulation resistance Resistance to the leakage current flowing through the insulator (inside or surface of the insulator) when 500 V is applied across adjacent pins of a connector ielectric withstanding voltage pplying the indicated voltage across adjacent pins of a connector for one minute does not cause any abnormality (damage or cracks in insulator). Insulating material, cleaning with chlorothene enotes the insulating material used, and indicates whether the insulating material can be cleaned with chlorothene. Some part numbers are indicated as examples. 4-2
Selection Table Rectanglar onnectors Model 360 series ppearance Structure Pin type Plating ontact pitch Number of contacts Solder eyelet (tail shape) Wire-wrapping (post cross section) rimping ( applicable WG No.) Straight, through hole (P board hole dimensions) Right-angle, through hole (P board hole dimensions) I ( applicable WG No.) Gold Silver Tin Operating temperature range urrent rating 2.54 2.54 8, 16, 24, 32, 40, 48, 56, 64 P 1.8 0.7 J 1.8 0.7 iagonal 0.71 mm (0.028 in.) P J WG #22 to #28 P φ1, 2.54 2.54 J φ1, 2.54 2.54 P φ1, 2.54 2.54 J φ1, 2.54 2.54 P J #28, Flat cable 55 to +85 3 (I type: 1) 4 Specification Voltage rating ontact resistance Insulation resistance ( 500 V) ielectric withstanding voltage (for 1 minute) Insulating material 250 V 15 mω max. ( 6 V, 0.3 ) 1,000 MΩ min. 500 V Polyester P (363J) (example) FN-361P024-U Remarks able cover provided 4-3
NOTES imensions are in millimeters (inches) www.fujitsu.takamisawa.com 4
RETNGULR ONNETORS FN-360 SERIES FETURES Many applications Various connectors are available for connection by means of soldering, wire wrapping, crimping, P board mounting, and insulation displacement connection (I). The user can choose a plug and jack combination that best meet each application. Small size for high-density mounting The connectors are small with a contact and terminal pitch of 2.54 mm (0.100 in.) between pins and between rows and are thus well suited for high-density mounting. Sturdy shell guide Sturdy shell guides are used to prevent mismating and to protect the pins. Excellent cost performance Streamlined design and automated manufacturing, including use of partial solder plating, provide excellent cost performance. SPEIFITIONS MTERILS Item Specification Item Material Operating temperature range 55 to +85 Insulator Polyester (363J: P94V-2) urrent Rating 3 (I type: 1 ) onductor opper alloy Voltage Rating 250 V Plating Gold plating, silver plating ontact resistance 15 mω max. ( 6 V, 0.3 ) Insulation resistance 1000 MΩ min. ( 500 V) ielectric withstanding voltage 500 V for 1 minute Insertion force 2.5 kg max. (8 contacts), 20 kg max. (64 contacts) Withdrawal force 0.3 kg min. (8 contacts), 2.3 kg min. (64 contacts) Soldering φ0.60 mm (0.024 in.) max, WG #23 or less Wire-wrapping φ0.32 mm (0.013 in.) to φ0.26 mm (0.010 in.), WG #28 to #30 pplicable wire rimping Standard contacts φ0.51 mm (0.020 in.) to φ0.32 mm (0.013 in.), WG #24 to #28, insulator φ1.2 mm (0.047 in.) max. ontacts for thick wires φ0.64 mm (0.025 in.) to φ0.32 mm (0.013 in.), WG #22 to #28, insulator φ1.7 (0.067 in.) max. I Flat cable 1.27 mm (0.050 in.) pitch, WG #28 (stranded wire), WG #30 (solid wire) pplicable P board 1.6 mm (0.063 in.) standard thick imensions are in millimeters (inches) www.fujitsu.takamisawa.com 5
PRT NUMER FN-36 7 J 048-U / H (Only for I) Shape of connector cover with I holders : lose end (special) F: lose end H: Through end Plating and cover specification U: Gold plating : Type cover (standard) : Type cover (for cable-to-cable connection) : Type cover (with metal cable clamp) E: Type E cover (with long lock-screws) F: Type F cover (64 contacts only) G1: One-touch lock type (40 contacts only) H/E: EMI protection type (40 contacts only) J1: Obtuse angle cable-out cover (40 contacts only) Number of contacts 8, 16, 24, 32, 40, 48, 56, 64 onnector or parts type : Metal fitting : over J: Jack P: Plug Tail type 0: over, metal fitting 1: Soldering 2: Wire-wrapping 3: rimping 4: Straight 5: Right-angle 7: I 360 series connector Fujitsu connector 6
PPLITION EXMPLE FN-365P FN-365J FN-364P FN-364P FN-364J FN-364J FN-365P FN-365J FN-364P FN-364J FN-362J FN-363J FN-365P FN-367J FN-361P FN-365P FN-364P With type cover FN-365J FN-364P With type E cover FN-365P FN-364J With type J1 cover FN-365P FN-365J With type G1 cover With type cover With type H/E cover With type E cover 7
SOLERING TYPE (PLUG) IMENSIONS 8.25 (0.324) 6 (0.236) 12.1 (0.476) 5.8 (0.228) 5 (0.196) 4 (0.157) 0.7 (0.027) 1.5 (0.059) 1 2 φ2.8 (0.110) MOUTING HOLE LYOUT [Panel] ( + 1) ±0.3 (( + 0.039) ±0.011 ) ±0.15 (0.005) 8.6(0.338) ±0.2(0.007) φ2.8(0.110) +0.15(0.005) 0 hole PRT NUMERS N IMENSIONS Number of contacts imensions: mm (in.) 8 FN-361P008-U 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FN-361P016-U 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FN-361P024-U 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FN-361P032-U 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FN-361P040-U 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FN-361P048-U 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FN-361P056-U 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FN-361P064-U 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) 8
SOLERING TYPE (JK) IMENSIONS 8.25 (0.324) 10.8 (0.425) 5.8 (0.228) 5 (0.198) 6 (0.236) 6 (0.236) 4 (0.157) 0.7 (0.027) 0.5 (0.019) 1.5 (0.059) 1 φ2.8 (0.110) OR MOUTING HOLE LYOUT [Panel] ( + 1) ±0.3 (( + 0.039) ±0.011) ±0.15 (0.005) 8.6 (0.338) ±0.2(0.007) φ2.8 (0.110) +0.15(0.005) 0 hole PRT NUMERS N IMENSIONS Number of contacts imensions: mm (in.) 8 FN-361J008-U 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FN-361J016-U 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FN-361J024-U 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FN-361J032-U 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FN-361J040-U 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FN-361J048-U 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FN-361J056-U 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FN-361J064-U 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) 9
WIRE-WRP TYPE (PLUG) IMENSIONS 8.25 (0.324) 10.3 (0.405) 4 (0.157) 10.8 (0.425) 0.71 (0.027) iagonal length φ2.8 (0.110) MOUTING HOLE LYOUT [oard] ±0.2 (0.007) ±0.15 (0.005) ±0.15(0.009) φ2.8 (0.110) +0.15(0.005) 0 hole φ1 (0.039) +0.1(0.0034) hole [Panel] ( + 1) ±0.3 (( + 0.039) ±0.011 ) ±0.15 (0.005) 8.6 (0.338) ±0.2(0.007) φ2.8 (0.110) +0.15(0.005) 0 hole PRT NUMERS N IMENSIONS Number of contacts imensions: mm (in.) 8 FN-362P008-U 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FN-362P016-U 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FN-362P024-U 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FN-362P032-U 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FN-362P040-U 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FN-362P048-U 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FN-362P056-U 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FN-362P064-U 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) 10
WIRE-WRP TYPE (JK) IMENSIONS 8.25 (0.324) 10.8 (0.425) 5.8 (2.283) 13.5 (0.531) 6 (0.236) 6 (0.236) 0.71 (0.027) 4 (0.157) iagonal length 1 φ2.8 (0.110) MOUTING HOLE LYOUT [oard] ±0.2 (0.007) ±0.15 (0.005) ±0.15(0.009) φ2.8 (0.110) 0 +0.15(0.005) hole φ1 (0.039) +0.1(0.0034) hole [Panel] ( + 1) ±0.3 (( + 0.039) ±0.011) ±0.15 (0.005) 8.6 (0.338) ±0.2(0.007) φ2.8 (0.110) +0.15(0.005) 0 hole PRT NUMERS N IMENSIONS Number of contacts imensions: mm (in.) 8 FN-362J008-U 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FN-362J016-U 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FN-362J024-U 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FN-362J032-U 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FN-362J040-U 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FN-362J048-U 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FN-362J056-U 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FN-362J064-U 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) 11
RIMP TYPE (JK HOUSING) IMENSIONS 8.25 (0.324) 10.8 (0.425) 6 (0.236) 5.8 (2.283) 6 (0.236) 22 (0.866) 4 (0.157) 6 (0.236) Pin 1 in row φ2.8 (0.110) MOUTING HOLE LYOUT Pin 1 in row [Panel] ( + 1) ±0.3 (( + 0.039) ±0.011 ) ±0.15 (0.005) 8.6 (0.338) ±0.2(0.007) φ2.8 (0.110) +0.15(0.005) 0 hole PRT NUMERS N IMENSIONS Number of contacts 8 16 24 32 40 48 56 64 FN-363J008 FN-363J016 FN-363J024 FN-363J032 FN-363J040 FN-363J048 FN-363J056 FN-363J064 28.84 (1.135) 39.0 (1.535) 49.16 (1.935) 59.32 (2.335) 69.48 (2.735) 79.64 (3.135) 89.8 (3.535) 99.96 (3.935) 23.34 (0.918) 33.5 (1.318) 43.66 (1.718) 53.82 (2.118) 63.98 (2.518) 74.14 (2.918) 84.3 (3.318) 94.46 (3.718) imensions: mm (in.) 17.84 (0.702) 28.0 (1.102) 38.16 (1.502) 48.32 (1.902) 58.48 (2.302) 68.64 (2.702) 78.8 (3.102) 88.96 (3.502) 7.62 (0.3) 17.78 (0.7) 27.94 (1.1) 38.1 (1.5) 48.26 (1.9) 58.42 (2.3) 68.58 (2.7) 78.74 (3.1) 12
RIMP TYPE (ONTT) IMENSIONS Standard contact (applicable wire: WG #24 to #28) Thick wire connection contact (applicable wire: WG #22 to #26) 20.05 (0.789) 20.05 (0.789) PRT NUMERS Type Plating Standard Thick wire connection contact Loose piece Gold plating FN-363J-U FN-363J-U/S Strip reeled Gold plating FN-363J-U/R FN-363J-U/T PRT NUMERS OF RIMPING TOOLS ontact type pplicable wire Wire cross-section area (mm 2 ) rimp height Insulator diameter Stripped length FN-363T-T005/H (Hand crimping tool) FN-363J-U (Loose piece) WG #24 0.20 to 0.24 1.25 mm (0.049 in.) to 1.30 mm (0.051 in.) φ1.2 mm (0.047 in.) max 3.0 mm (0.118 in.) to 4.0 mm (0.157 in.) FN-363J-U/R (Strip reeled) WG #26 0.13 to 0.16 1.20 mm (0.047 in.) to 1.25 mm (0.049 in.) φ1.2 mm (0.047 in.) max 3.0 mm (0.118 in.) to 4.0 mm (0.157 in.) WG #28 0.088 to 0.096 1.15 mm (0.045 in.) to 1.20 mm (0.047 in.) φ1.2 mm (0.047 in.) max 3.0 mm (0.118 in.) to 4.0 mm (0.157 in.) FN-363T-T011/H (Hand crimping tool) FN-363J-U/S (Loose piece) WG #22 0.30 to 0.40 0.85 mm (0.033 in.) to 0.95 mm (0.037 in.) φ0.9 mm (0.035 in.) 1.8 mm (0.071 in.) 3.0 mm (0.118 in.) to 4.0 mm (0.157 in.) FN-363J-U/T (Strip reeled) WG #24 0.20 to 0.24 0.75 mm (0.029 in.) to 0.85 mm (0.033 in.) φ0.9 mm (0.035 in.) 1.8 mm (0.071 in.) 3.0 mm (0.118 in.) to 4.0 mm (0.157 in.) WG #26 0.13 to 0.16 0.73 mm (0.028 in.) to 0.81 mm (0.031 in.) φ0.9 mm (0.035 in.) 1.8 mm (0.071 in.) 3.0 mm (0.118 in.) to 4.0 mm (0.157 in.) [Hand crimping tool] [ontact withdrawal tool] 10 (0.393) 65 (2.559) FN-360T-T001/H 13
STRIGHT TYPE (PLUG) IMENSIONS 8.25 (0.324) 10.3 (0.405) 4 (0.157) 4.2 (0.165) 0.71 (0.027) iagonal length 1 φ2.8 (0.110) OR MOUTING HOLE LYOUT PRT NUMERS N IMENSIONS [oard] ±0.2 (0.007) ±0.15 (0.005) ±0.15(0.009) φ2.8 (0.110) 0 +0.15(0.005) hole φ1 (0.039) +0.1(0.0034) hole Number of contacts imensions: mm (in.) 8 FN-364P008-U 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FN-364P016-U 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FN-364P024-U 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FN-364P032-U 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FN-364P040-U 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FN-364P048-U 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FN-364P056-U 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FN-364P064-U 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) 14
STRIGHT TYPE (JK) IMENSIONS 8.25 (0.324) 10.8 (0.425) 6 (0.236) 5.8 (0.228) 4.2 (0.165) 6 (0.236) 0.71 (0.027) iagonal length 4 (0.157) 1 φ2.8 (0.110) OR MOUTING HOLE LYOUT [oard] PRT NUMERS N IMENSIONS ±0.2 (0.007) ±0.15 (0.005) ±0.15(0.009) φ2.8 (0.110) +0.15(0.005) 0 hole φ1 (0.039) +0.1(0.0034) hole Number of contacts imensions: mm (in.) 8 FN-364J008-U 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FN-364J016-U 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FN-364J024-U 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FN-364J032-U 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FN-364J040-U 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FN-364J048-U 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FN-364J056-U 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FN-364J064-U 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) 15
RIGHT-NGLE TYPE (PLUG) IMENSIONS N "' 0 e e N.,; ;JI; N nn--- ---nn,, cc I e,,,, /... "' 2.8 (0.110) ---+----- --- 3 (0.118), I I. 0 0.71 (0.027) iagonal length ---!-------- MOUTING HOLE LYOUT [oard] 0 --1-----+fi-l--- - - 2 +---i- - ---=l''i==---+:::s;:=r.. ±o.,s(o.oos) 2.8 (0 110)jl15<0-005)hole 1 (0 039t0-1co0039) hole Unit: mm in. PRT NUMERS N IMENSIONS Number of contacts 8 FN-365P00S.U 28.84 (1.135) 16 FN-365P01 S.U 39.0 (1.535) 24 FN-365P024-U 49.16 (1.935) 32 FN-365P032-U 59.32 (2.335) 40 FN-365P040.U 69.48 (2.735) 48 FN-365P04S.U 79.64 (3.135) 56 FN-365P05S.U 89.8 (3.535) 64 FN-365P064-U 99.96 (3.935) NOTE Note on mounting a right-angle plug on a board Metal fitting Plug Mount the connector so that it Pc 0 \ /, projects from the board by at least 1.5 mm (0.059 in.). 1.5 mm (0.059 in.) imensions: mm (in.) 23.34 (0.918) 17.84 (0. 702) 7.62 (0.3) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 43.66(1.718) 38.16 (1.502) 27.94 (1.1) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 74.14 (2.918) 68.64 (2. 702) 58.42 (2.3) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) 16
RIGHT-NGLE TYPE (JK) IMENSIONS 8.25 (0.324) 4 (0.157) 11 (0.433) 5 (0.196) 5 (0.196) 8 (0.314) φ2.8 (0.110) 3 (0.118) 1 0.8 (0.031) iagonal length MOUTING HOLE LYOUT [oard] 3.27 (0.128) ±0.15(0.005) 5 (0.196) ±0.2 (0.007) ±0.15 (0.005) Edge of board ±0.15(0.009) φ2.8 (0.110) 0 +0.15(0.005) hole φ1 (0.039) +0.1(0.0034) hole Note on mounting a right-angle jack on a board Mount the connector so that it projects from the board by at least 5 mm (0.197 in.). PRT NUMERS N IMENSIONS Number of contacts imensions: mm (in.) 8 FN-365J008-U 28.84 (1.135) 23.34 (0.918) 17.84 (0.702) 7.62 (0.3) 16 FN-365J016-U 39.0 (1.535) 33.5 (1.318) 28.0 (1.102) 17.78 (0.7) 24 FN-365J024-U 49.16 (1.935) 43.66 (1.718) 38.16 (1.502) 27.94 (1.1) 32 FN-365J032-U 59.32 (2.335) 53.82 (2.118) 48.32 (1.902) 38.1 (1.5) 40 FN-365J040-U 69.48 (2.735) 63.98 (2.518) 58.48 (2.302) 48.26 (1.9) 48 FN-365J048-U 79.64 (3.135) 74.14 (2.918) 68.64 (2.702) 58.42 (2.3) 56 FN-365J056-U 89.8 (3.535) 84.3 (3.318) 78.8 (3.102) 68.58 (2.7) 64 FN-365J064-U 99.96 (3.935) 94.46 (3.718) 88.96 (3.502) 78.74 (3.1) 18
I TYPE (JK) IMENSIONS [onnector body] 11.5 (0.452) 5 (0.196) 8.25 (0.324) 6 (0.236) 4 (0.157) 5 (0.196) [onnector cover with I holders] 8.25 (0.324) 4 (0.157) 5 (0.196) 8.25 (0.324) 8.25 (0.324) [losed-end type] [Strain relief] [Through-end type] 15.7 (0.618) 31 (1.220) 6 (0.236) [Lock-screw] 10 (0.393) M2.6 (0.102) φ5 (0.196) PRT NUMERS N IMENSIONS Number of contacts Through-end cover lose-end cover imensions: mm (in.) 8 FN-367J008-U/H FN-367J008-U/F 28.84 (1.135) 23.34 (0.918) 7.62 (0.3) 16 FN-367J016-U/H FN-367J016-U/F 39.0 (1.535) 33.5 (1.318) 17.78 (0.7) 24 FN-367J024-U/H FN-367J024-U/F 49.16 (1.935) 43.66 (1.718) 27.94 (1.1) 32 FN-367J032-U/H FN-367J032-U/F 59.32 (2.335) 53.82 (2.118) 38.1 (1.5) 40 FN-367J040-U/H FN-367J040-U/FW* 69.48 (2.735) 63.98 (2.518) 48.26 (1.9) 48 FN-367J048-U/H FN-367J048-U/F 79.64 (3.135) 74.14 (2.918) 58.42 (2.3) 56 FN-367J056-U/H FN-367J056-U/F 89.8 (3.535) 84.3 (3.318) 68.58 (2.7) 64 FN-367J064-U/H FN-367J064-U/F 99.96 (3.935) 94.46 (3.718) 78.74 (3.1) *: FN-367J040-U/F is replaced by part number FN-367J040-U/FW, which indicates change of manufacturing location for this device. 19
I TOOLS Special I tools are used to assemble FN-360 series connectors and flat cables. FETURES The mechanisms are simple, so even novices can use them easily. Those who already have Fujitsu-manufactured I tools for other series connectors need only purchase the locator plate. The hand press and cable cutter are designed to be used in common with all connectors. The assembly of cables and connectors with various numbers of contacts can be done by selective setting of the connector guides to the specified positions. The cable cutter has an extremely sharp cutting edge. Hand press able cutter Locator plate (That for the 790 series is shown in the photograph.) Notes: detailed operation manual and instruction manual for I tools are available upon request. Should any question arise in using the I tools, consult our branch offices or agents in your area. ORERING OES FOR I TOOLS Tool name able cutter (common) Hand press (common) Locator plate (for 360 series connectors) FN-707T-T001/H FN-707T-T101/H FN-367T-T012/H The hand press and cable cutter can be used for other I connectors. OVER OMINTIONS ETWEEN OVERS N ONNETORS onnector over FN-360 - FN-360 - FN-360 - FN-360 -E FN-360064-F FN-360040-G1 FN-360040-H/E FN-360040-J1 Plug Jack Soldering Soldering Wire-wrapping rimping Number of contacts 8 16 24 32 40 48 56 64 These covers cannot be used for I connectors. 20
OVER (TYPE ) IMENSIONS R G R: 2.84 mm (0.112 in.) (8 and 16 contacts) R: 4.0 mm (0.157 in.) (24 to 64 contacts) H 14 mm (0.551 in.) max 10.3 (0.405) FUJITSU 28 (1.102) 37 (1.456) 46 (1.811) F 1 (0.039) EXPLOE VIEW Two M2 mm (0.079 in.) thread 8 mm (0.315 in.) long pan head machine screws (shorter) Four M2 mm (0.079 in.) thread nuts Two M2 mm (0.079 in.) thread 10 mm (0.394 in.) long pan head machine screws (longer) Two washers ase onnector Two lock-screws Note: The screws, nuts, washers, and lock-screws are attached to the cover. PRT NUMERS N IMENSIONS Number of contacts 8 16 24 32 40 48 56 64 FN-360008- FN-360016- FN-360024- FN-360032- FN-360040- FN-360048- FN-360056- FN-360064-23.34 (0.918) 33.50 (1.318) 43.66 (1.718) 53.82 (2.118) 63.98 (2.518) 74.14 (2.918) 84.30 (3.318) 94.46 (3.718) F 32.08 (1.262) 42.24 (1.662) 52.40 (2.062) 62.56 (2.462) 72.72 (2.862) 82.88 (3.262) 93.04 (3.662) 103.20 (4.062) imensions: mm (in.) G 2.0 (0.078) 6.0 (0.236) 10.0 (0.393) 14.0 (0.551) 18.0 (0.708) H φ 5.7 (0.224) φ 5.7 (0.224) φ 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 21
OVER FOR LE TO LE ONNETION (TYPE ) IMENSIONS R G R: 2.84 mm (0.112 in.) (8 and 16 contacts) R: 4.0 mm (0.157 in.) (24 and 64 contacts) H 14 mm (0.551 in.) max. 10.3 (0.405) Note: This cover can be combined with a cover of type,, or E for cableto-cable connection. FUJITSU 28 (1.102 46 (1.811) F 1 (0.039) Metal fittings EXPLOE VIEW Two screws for mounting metal fittings Two M2 mm (0.079 in.) thread 8 mm (0.315 in.) long pan head machine screws (shorter) onnector Four M2 mm (0.079 in.) thread nuts Two M2 mm (0.079 in.) thread 10 mm (0.394 in.) long pan head machine screws (longer) Two washers Two metal fittings onnector ase Note: The screws, nuts, washers, and accessory are attached to the cover. PRT NUMERS N IMENSIONS Number of contacts 8 16 24 32 40 48 56 64 FN-360008- FN-360016- FN-360024- FN-360032- FN-360040- FN-360048- FN-360056- FN-360064- F 32.08 (1.262) 42.24 (1.662) 52.40 (2.062) 62.56 (2.462) 72.72 (2.862) 82.88 (3.262) 93.04 (3.662) 103.20 (4.062) imensions: mm (in.) G 2.0 (0.078) 6.0 (0.236) 10.0 (0.393) 14.0 (0.551) 18.0 (0.708) H φ 5.7 (0.224) φ 5.7 (0.224) φ 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 22
OVER (WIE OPENING TYPE) (TYPE ) IMENSIONS able clamp I 7.5 (0.295) 37 (1.456) 10.5 (0.413) 14 mm (0.551 in.) max. 10.3 (0.405) FUJITSU 1 (0.039) 28 (1.102) 46 (1.811) F EXPLOE VIEW Four M2 mm (0.079 in.) thread 8 mm (0.315 in.) long pan head machine screws (shorter) Four M2 mm (0.079 in.) thread nuts Two cable clamps ase onnector Two lock-screws Note: The screws, nuts, cable clamp, and lockscrews are attached to the cover. PRT NUMERS N IMENSIONS Number of contacts 40 48 56 64 FN-360040- FN-360048- FN-360056- FN-360064-63.98 (2.518) 74.14 (2.918) 84.30 (3.318) 94.46 (3.718) imensions: mm (in.) F 72.72 (2.862) 82.88 (3.262) 93.04 (3.662) 103.20 (4.062) I 8.0 (0.314) 12.0 (0.472) 16.0 (0.629) 20.0 (0.789) 23
OVER (LONG-SREW TYPE) (TYPE E) IMENSIONS R G R: 2.84 mm (0.112 in.) (8 and 16 contacts) R: 4.0 mm (0.157 in.) (24 and 64 contacts) H 14 mm (0.551 in.) max. 10.3 (0.405) FUJITSU 1 (0.039) 28 (1.102) 46 (1.811) 53 (2.086) F EXPLOE VIEW Two M2 mm (0.079 in.) thread 8 mm (0.315 in.) long pan head machine screws (shorter) Four M2 mm (0.079 in.) thread nuts Two M2 mm (0.079 in.) thread 10 mm (0.394 in.) long pan head machine screws (longer) Two washers ase onnector Two lock-screws Note: The screws, nuts, washers, and lock-screws are attached to the cover. PRT NUMERS N IMENSIONS Number of contacts 8 16 24 32 40 48 56 64 FN-360008-E FN-360016-E FN-360024-E FN-360032-E FN-360040-E FN-360048-E FN-360056-E FN-360064-E 23.34 (0.918) 33.50 (1.318) 43.66 (1.718) 53.82 (2.118) 63.98 (2.518) 74.14 (2.918) 84.30 (3.318) 94.46 (3.718) F 32.08 (1.262) 42.24 (1.662) 52.40 (2.062) 62.56 (2.462) 72.72 (2.862) 82.88 (3.262) 93.04 (3.662) 103.20 (4.062) imensions: mm (in.) G 2.0 (0.078) 6.0 (0.236) 10.0 (0.393) 14.0 (0.551) 18.0 (0.708) H φ 5.7 (0.224) φ 5.7 (0.224) φ 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 8.0 (0.314) 24
OVER (STRIGHT LE-OUT OVER) (TYPE F) IMENSIONS Section S 19.5 (0.767) 17.5 (10.688) etail of section S 94.46 (3.718) 30.5 (1.200) 6 (0.236) 8 (0.314) 10 (0.393) 14 mm (0.551 in.) max. 10.3 (0.405) FUJITSU 1 (0.039) 28 (1.102) 37 (1.456) 46 (1.811) 55 (2.165) 103.2 (4.062) EXPLOE VIEW Six M2 mm (0.079 in.) thread 8 mm (0.315 in.) long pan head machine screws Six M2 mm (0.079 in.) thread nuts Two cable clamps ase onnector Two lock-screws Note: The screws, nuts, cable clamps, and lockscrews are attached to the cover. PRT NUMER FN-360064-F 25
OVER (RIGHT NGLE LE-OUT OVER) (TYPE G1) IMENSIONS 19 (0.748) 6 (0.236) F 20 (0.787) 20 (0.787) ø9 (0.354) 17 (0.669) 10 (0.393) 81.48 (3.207) 17 (0.669) 14.65 (0.576) EXPLOE VIEW ase onnector Two cable clamps Slider ase Two M2.6 mm (0.102 in.) thread 8 mm (0.315 in.) long pan head machine screws LOKE STTE METL FITTINGS 6 (0.236) F Metal fittings FN-36011 P board 1 mm (0.039 in.) min. Note: fter connectors are mated, moving the slider locks the connectors. Note: The FN-360 11-metalfittings are used for this cover. PRT NUMER FN-360040-G1 26
OVER (RIGHT NGLE LEOUT OVER) (TYPE H/E) IMENSIONS Material: Zync die cast Plating: Nickel plating 63.98 (2.518) 1 (0.039) 17 (0.669) 1 (0.039) M2.5 (0.098) 8 (0.314) 43.98 (1.731) φ11 (0.433) able hole M2.5 (0.039) Through-hole F 72.48 (2.853) 12 (0.472) 19 (0.748) 1 (0.039) 46 (1.811) 10 (0.393) EXPLOE VIEW Two M2.5 mm (0.098 in.) thread 5 mm (0.197 in.) long pan head machine screws Two M2.5 mm (0.098 in.) thread 8 mm (0.315 in.) long pan head machine screws ase onnector able clamp Two lock-screws Note: The screws, cable clamp, and lock-screws are attached to the cover. PRT NUMER FN-360040-H/E 27
OVER (OTUSE NGLE LE-OUT OVER (40 ONTTS ONLY)) (TYPE J1) IMENSIONS M2.6 (0.102) 25 (0.984) Two screws φ12 (0.472) able hole 63.98 (2.518) 20 (0.787) 46 (1.811) 24 (0.944) F M2 (0.078) 14 (0.511) Three screws 1 (0.039) 71.73 (2.824) 10.3 (0.405) 7 EXPLOE VIEW Three M2 mm (0.079 in.) thread 14 mm (0.551 in.) long screws Two M2.6 mm (0.102 in.) thread 25 mm (0.984 in.) long screws ase Two M2.6 mm (0.102 in.) thread 12 mm (0.472 in.) long screws onnector able clamp ase Two M2.6 mm (0.102 in.) thread nuts Three M2 mm (0.079 in.) thread nuts PRT NUMER FN-360040-J1 28
LOW PROFILE OVER (OTUSE NGLE LE -OUT) (TYPE J2) IMENSION : FN-360024-J2 (24 contacts) : FN-360040-J2 (40 contacts) 8.70 M2.6 mm (0.102 in.) thread machine screw with washer 6 (MX) 5 (MIN) 17.9 51.41 (2.024) 12 View from R4 25 M2 (0.078) 22 20 12.75 M2.6 mm machine screw with washer View from 29.66 (1.167) 46 (1.811) 24 (0.944) F 30 9.5 (0.374) M2 (0.078) 46 (1.811) 1 (0.039) 24 (0.944) M2 (0.078) F 63.98 71.73 M2 (0.078) 10.3 (0.405) 1 (0.039) 43.66 (1.718) 10.3 (0.405) EXPLOE VIEW Three M2 mm (0.079 in.) thread 8 mm (0.315 in.) long screws Two M2.6 mm (0.102 in.) thread 25 mm (0.984 in.) long screws ase Two M2.6 mm (0.102 in.) thread 6 mm (0.236 in.) long screws onnector able clamp ase Two M2.6 mm (0.102 in.) thread nuts Three M2 mm (0.079 in.) thread nuts PRT NUMER FN-360024-J2 FN-360040-J2 29
ESSORIES MOUNTING SYLE [Straight mounting metal fitting] Jack with cover Plug [Right-angle mounting metal fitting] Metal fitting P Plug or jack Jack with cover or plug with cover [Straight mounting round metal fitting] Metal fitting Jack with cover or plug with cover Plug or jack P Metal fitting M2.6 8 M2.6 10 P M2.6 8 Note: The M2.6 mm (0.102 in.) thread 8 mm (0.315 in.) long machine screw shall be separately prepared. Note: The M2.6 mm (0.102 in.) thread 10 mm (0.394 in.) long machine screw shall be separately prepared. Note: The M2.6 mm (0.102 in.) thread 8 mm (0.315 in.) long machine screw shall be separately prepared. SELETION OF METL FITTINGS ORING TO OMINTION OF ONNETORS N OVERS Jack over mounting side 361J 362J 363J 364J 367J Plug With cover Without cover With cover Without cover With cover Without cover With cover Without cover With cover Without cover Metal fitting mounting side 361P 362P 364P 365P Metal fitting part number FN-3604 FN-3601 FN-3601 FN-3602 FN-3605 FN-3606 FN-3606 FN-3603 FN-3604 FN-3601 FN-3601 FN-3602 FN-3605 FN-3606 FN-3606 FN-3603 FN-3604 FN-3601 FN-3601 FN-3602 FN-3605 FN-3606 FN-3606 FN-3603 FN-3604 FN-3601 FN-3601 FN-3602 FN-3605 FN-3606 FN-3606 FN-3603 FN-3605 FN-3606 FN-3606 FN-3603 Plug over mounting side 361P 361P 364P Jack With cover Without cover With cover Without cover With cover Without cover 361J FN-3604 FN-3605 FN-3607 FN-3607 Metal fitting mounting side 362J 363J 364J 365J Metal fitting part number FN-3604 FN-3604 FN-3604 FN-36010 (FN-3608) FN-3605 FN-3605 FN-3605 FN-3609 FN-3607 FN-3607 FN-3607 FN-3609 FN-3607 FN-3607 FN-3607 FN-3609 367J FN-3604 FN-3605 FN-3607 FN-3607 Note: When the jack or plug without a cover (shaded part) is used, have M2.6 8 mm machine screws ready inorder to tighten the connector. 30
SHPES N IMENSIONS OF METL FITTINGS 1.Straight Mounting Metal Fittings Shape Symbol FN-3601 FN-3606 M2.6 (0.102) 8.25 (0.326) 5.3 (0.208) 6.3 (0.248) 5.5 (0.216) 2.Right-angle Mounting Metal Fittings Shape Symbol FN-3602 FN-3603 M2.6 (0.102) 7 (0.275) 3 (0.118) 4 (0.157) 4 (0.157) 5.5 (0.216) 9 (0.354) 10 (0.393) Shape Symbol FN-3608 FN-3609 M2.6 (0.102) 7.5 (0.295) 5.3 (0.208) 6.3 (0.248) 4 (0.157) 5.4 (0.212) 13.3 (0.523) 14.3 (0.526) Symbol FN-36010 Symbol FN-36011 M2.6 (0.102) 5.5 (0.216) 4 (0.157) 1 (0.039) M2.6 (0.102) M2.6 (0.102) 8.1 (0.318) 4.6 (0.181) 5.3 (0.208) 7.5 (0.295) 4 (0.157) 1 (0.039) 6 (0.236) 3 (0.118) 7 (0.275) 5.5 (0.216) 3.Straight Mounting Round Metal Fittings Shape Symbol FN-3604 FN-3605 FN-3607 M2.6 (0.102) 6 (0.236) 5.25 (0.206) 7.1(0.279) 9.9 (0.389) 8.1 (0.318) 31
ontact Japan FUJITSU OMPONENT LIMITE Shinagawa Seaside Park Tower 12-4, Higashi-shinagawa 4-chome, Tokyo 140 0002, Japan Tel: (81-3) 3450-1681 Fax: (81-3) 3474-2385 Email: fcl-contact@cs.jp.fujitsu.com Web: www.fujitsu.com/jp/group/fcl/en/ North and South merica FUJITSU OMPONENTS MERI, IN. 2290 North First Street, Suite 212 San Jose, 95131 U.S.. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components/ Europe FUJITSU OMPONENTS EUROPE.V. iamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ sia Pacific FUJITSU OMPONENTS SI, Ltd. 102E Pasir Panjang Road #01-01 itilink Warehouse omplex, Singapore 118529 Tel: (65) 6375-8560 / Fax: (65) 6273-3021 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/devices/ components/ hina FUJITSU ELETRONI OMPONENTS (SHNGHI) O., LT. Unit 4306, Interontinental enter 100 Yu Tong Road, Shanghai 200070, hina Tel: (86 21) 3253 0998 /Fax: (86 21) 3253 0997 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/devices/ components/ Hong Kong FUJITSU OMPONENTS HONG KONG o., Ltd. Room 06, 28/F, Greenfield Tower, oncordia Plaza, No.1 Science Museum Road, Tsim Sha Tsui East, Kowloon, Hong Kong Tel: (852) 2881 8495 Fax: (852) 2894 9512 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/devices/ components/ Korea FUJITSU OMPONENTS KORE, LT. lpha Tower #403, 645 Sampyeong-dong, undang-gu, Seongnam-si, Gyeonggi-do, 13524 Korea Tel: (82 31) 708-7108 Fax: (82 31) 709-7108 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/ devices/components/ opyright ll trademarks or registered trademarks are the property of their respective owners. Fujitsu omponents merica or its affiliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu omponents merica, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice. opyright 2017 Fujitsu omponents merica, Inc. ll rights reserved. Revised May 16, 2017. 32
Mouser Electronics uthorized istributor lick to View Pricing, Inventory, elivery & Lifecycle Information: Fujitsu: FN-360040-J2 FN-361J040-U FN-360024- FN-364P040-U FN-361J024-U FN-367J040-U/H FN-364P024-U FN-363T-T011/H FN-3601 FN-360008-E FN-360024- FN-360024-J2 FN- 361J008-U FN-361P024-U FN-363J040 FN-364J032-U FN-364J040-U FN-364P008-U FN- 365P008-U FN-365P024-U FN-367J024-U/F FN-367J040-U/F FN-367J056-U/F FN361J048-U FN360048 FN-365P040-U/#01 FN-365P040-U/#01 FN-360048-E FN-365P040-U#01 FN- 365P040-U/#01 FN-364P040-U/#01 FN-365P080-U/26 FN-365P080-U/27