1026 outdoor Cockpit
Cockpit 1027 Roadbook RB-TT *MvG* For the first time ever, step motors are being used in this new Roadbook holder. Using an intelligent control that recognises the entire length of the Roadbook and the position (beginning... end), these step motors are controlled in normal operation to ensure that an even feeder speed is achieved for the Roadbook. However, much higher step motor revolutions are used for fast rewinding. A quick press of the remote control moves the Roadbook forward by one picture; the picture height can be set between approx. 50 and 1 00 mm. This greatly increases the safety, since the rider is not so distracted when moving on to the next picture. The Roadbook lighting adapts automatically to the prevailing light conditions. Features at a glance: - Step motor drive with standstill brake - Remote control and manual operation - Movable tension pulley with non-contact sensor for consistent paper tension - Feed speed not dependent on the diameter of the winding roll - Single-image feed with adjustable picture height - Lighting adapts automatically to the brightness of the surroundings - Integrated writing base for subsequent lettering of the Roadbook - Tremendous capacity of to 80 sheets of DIN A5 (to approx. 1 7 m) - Housing dimensions (l x w x h) 207x1 51x 83,5 mm 020-0012
1028 RB-XL The roadbook holder in A4 format! This means you don t have to cut maps to size and write on narrow continuous paper rolls. And so, for example, you can also insert the A4 printout from your route planning software directly into the roadbook holder. - Including fixing materials for handlebars with crossbar (012mm); - Also RB compact with clamp for fitting directly onto a 0 22mm handlebar tube. - For all kind of notes - Dimensions: RB-compact: 90 x 1 30 x 40; RB-XL 245 x 1 30 x 55 mm - Paper width up to 60mm (RB-compact) or 21 0 mm (RB-XL) - Waterproof - Rugged aluminium housing - Front cover opens and closes without tools - Manual operation - Belt-driven paper brake to prevent the paper roll from unwinding - For use on all types of motorcycles - Optional green, energy-saving LED lighting - Devise your own route plans (roadbooks)! 020-0030 Roadbookholder RB-XL 025-0021 Lighting 100 mm 020-0020 Roadbookholder RB-compact 025-0030 Paper roll 60mm 025-0020 Lighting 60mm 025-0025 Adapter plate DR RB-compact
Cockpit 1029 RB-TT We used our many years of experience to design our roadbook holder. It features a unique DOUBLE MOTION drive which means that two motors control paper movement. The paper is always tightened and cannot unwind even with strong vibration. We deliberately decided not to use rubber driving belts which are prone to ageing and cracks. We have chosen a direct drive instead. The RB-TT standard package includes a lighting kit and handlebar control. The roadbook holder is easy to mount and the electrical connections are simple. Just connect two cables to the power supply. Then plug in the handlebar control. The handlebar bracket is pre-assembled and is rubber mounted. Different mounting plates are available for mounting a trip computer with or without control lamps. - Aluminium housing - Reinforced edges for high stability - Waterproof - For A5 roadbooks - Lighting included - Housing dimensions: (L x W x H) 197x124x70mm - Electrical drive incl. paper brake - Manual operation possible - Includes handlebar control - Opens and closes with no tools - Extra large paper roll: up to 80 A5 sheets (approx. 17m) - Weight: 1000g incl. mount 020-0010 RB-compact The Roadbook holder for touring riders! Rallyists have used roadbook holders for years. More and more touring riders also want to benefit from notes that appear by simply turning a knob. Rally roadbook holder are often too big. Many motorcycles do not have enough space or the rider cannot see the instruments. There is a small roadbook holder available: the RB compact.
1030 Roadbook Lighting Lighting for all standard roadbook holders. Voltage supply from motorcycle s electrical system - Very bright, constant backlighting - Extremely flat (just 2.5 mm); diameter of paper roll not restricted - Tested at the most demanding rallyes world-wide - Easy to mount - Dimensions: 100 mm x14 mm or 60 mm x 14 mm - Includes installation hardware, - Connectors etc. 025-0021 (100 mm) 025-0020 (60 mm) We offer a wide range of accessories and spare parts for all our roadbook holders. We cannot list the whole range in this catalogue due to the variety of parts in stock. If you do not see the spare part you need, just give us a call. Or send an e-mail to info@touratech.com. Paper roll 150 mm 025-0031 Roadbook forms (150mm pad) for RB-TT, RB-01, RB-MD 025-0032 Spare cover RB-compact 025-0041 Spare cover RB-TT 025-0040 Spare cover RB-TT carbon 025-0140 Spare cover RB-01/RB-MD 025-0042 Spare belt kit RB-01 025-0052 Spare belt kit RB-compact 025-0050 Dirk Schäfer Morokko
Cockpit 1031 IMO-100R300 The rallye computer IMO-100R300 is TOURATECH s high-end device. It features the same basic functions as the IMO-100R, but offers a host of additional features. - For use on all types of motorcycles with alternater or generator system (with or w/o battery) - Simple to fit - Provides a lot of information and has many functions - Replaces nearly all standard instruments - For use as replacement instrument - Time of day, date - Speedometer and rev counter (simultaneous display) - Display of total distance travelled up to 999 999 (editable) - Fuel consumption calculator and distance covered between fills - Daily trip recorder incl. Average speed (with and w/o break times) - Trip distance recorder incl. Average speed (with and w/o break times) - Outdoor thermometer with storage of minimum and maximum temperatures - Display of motor temperature - Countdown tripmeter showing distance to destination incl. arrival time and time to destination - Long distance recorder stores daily distances covered for up to 365 days (automatic) - Memorises maximum speed - Battery voltage indicator incl. generator monitoring - Package includes all sensors and cables - An adapter may be necessary for installing the motor temperature sensor. - Accessories can be found on the following pages The + version of the IMO-100R300 can be fitted to motorcycles with 6 volt or AC (w/o battery) systems. It is equipped with an integrated regulator/rectifier. On the + version the battery voltage indicator will display 1 1.5 V at all times. 012-0011 (IMO-100R300) English Version
1032 IMO-100R50 Rallye The rallye computer! The IMO-100R50 Rallye is the new rallye computer from TOURATECH. It combines the tried and tested rallye functions of the IMO-100R with very small dimensions (93 x 57 x 33 mm). The IMO-100R50 Rallye has a robust, waterproof aluminium housing. Although it has been conceived as rallye computer, it can be used as replacement instrument (German TUV Type Approval). The IMO-100R50 Rallye easily connects to your motorcycle s electrical system. It accepts 6 to 30 volts Ac or DC supply. A magnet for the wheel, and the wheel sensor are included. An optional handlebar remote control can be plugged into the IMO-100R50 Rallye directly. The Rallye IMO-100R50 allows you to switch between two different display modes: Speedo mode with daily trip odometer Simultaneous display of: - Speed - Daily trip odometer - Time of day - Odometer Rallye computer mode Simultaneous display of: - Total distance covered, can be edited via remote control in steps of 10m, 50m or 100m or be edited at IMO-100R50 Rallye directly using. - Partial distance (stage) can be reset via remote control or at IMO-100R50 Rallye directly - Time of day - Total distance covered or stage with large or small display 011-0401
Cockpit 1033 FB-PRO Handlebar Control - For all IMO computers - Mounted on handlebars - Plugs into IMO computer - Rallye function control - Used to select and reset functions on IMO-100R300 and IMO-100R Sport - Aluminium housing - Replaceable protective caps - Three keys - Very small Handlebar control FB-PRO 015-0020 Handlebar control FB-PRO 50R 015-0025 Sensor Mount Assembly - For fitting IMO sensor to upside-down forks (e.g.wp) - Sensor protection - Rugged mount - Special magnet mount - Mounts onto hub 015-0033 WP Fork 1997 and newer 015-0030 IMO Standard FB-RALLYE Handlebar Control: - For all IMO computers - Mounted on handlebars - Plugs into IMO computer - Rally function control - Used to select and reset functions on IMO- 100R300 and IMO-100R Sport - Extra large and rugged keys Handlebar control FB-Rallye IMO 015-0022 Handlebar control FB-Rallye 50R 015-0026 FB Rallye 5 Remote handlebar control for Tripmaster and RB-TT roadbook holder: Aluminium housing for handlebars with a diameter of 22 mm Width of housing 22 mm 3 red waterproof switches to operate the IMO: Resetting sections and correcting the total distance forward and backward. 2 blue waterproof switches to operate the roadbook holder: Winding the roadbook forward and backward. 015-0027 015-0129 for IMO-100R50
1034 Adapter plate L-I-K For mounting an IMO computer and a STD control lamp to the handlebars or handlebar brace (crossbar). Includes three clamps and a rubber mount. 040-0010 Adapter plate L-I-KS For mounting an IMO computer and a SPORT control lamp to the handlebars or fairing. Includes three clamps and a rubber mount. 040-0019 Adapter plate RB-I For mounting an IMO computer and an RB-TT roadbook holder. Includes screws and four vibration-isolating rubber mounts. 040-0011 Find more Adapterplates in the Touratech Webshop: www.shop.touratech.com Adapter plate RB-I-K For mounting an IMO computer and a control lamp kit STD to the RB-TT roadbook holder. Includes screws and four vibration-isolating rubber mounts. 040-0012 Adapter plate RB-MD- IMO For mounting an IMO computer to the RB-MD roadbook holder. Includes screws and four vibration-isolating rubber mounts. 040-0014 Adapter plate RB-TT-ICO For mounting an ICO rallye computer to the RB-TT roadbook holder. 040-0013
Xpol Superseal Connector Using these connectors you can create a waterproof connection to X poles. The set consists of the plug housing, crimp contacts and seals. These connectors were developed forairbag systems and are still used for this because they are very strong. 015-0079 (1 pol) 015-0080 (2 pol) 015-0081 (3 pol) 015-0082 (4 pol) Dummy plug for 2pol superseal connector 015-0078 Cockpit 1035 Power Converter - Sports, off-road and racing bikes often feature a stripped electrical system to reduce weight. - We offer a power converter that can be retrofitted which is a control, rectifier and capacitor unit. - This unit is required to operate the standard IMO computer as well as the electrical roadbook holder. - Weight: just 45g - Input voltage: 4.5-40 V DC or max. 25 VAC - Output voltage: 12 V DC, max. 200 ma 030-0020 Carimpuls Pulse Splitter In order to determine the speed with our IMO range a magnet is fitted to one of the wheels and a sensor counts the revolutions. Particularly with cars it is difficult to find a good place on the wheel for the magnet and the sensor and, for example, the drive shaft is once more placed underneath up to the wheel and there are too many pulses per wheel revolution. Even with quads the wheel size can be too small to set it on the IMO. We have designed a pulse splitter for these problems. You can use this to reduce (split) the pulses by factors of 2, 4, 8 and 1 6. This pulse splitter is simply connected to the sensor lead, the split factor is set and there you are with the right speed on the display even though the number of revolutions on the drive shaft, for example, is twice as many as the wheel revolutions. 015-0068
1036 Control Lamp Adapter Cable for BMW R 850 GS / R 1100 GS / R 1150 GS For directly connecting a control lamp kit or a SPORT control lamp kit to a BMW R850GS / R1100GS / R1150GS Adapter cable R259/21 030-0035 Control Lamp Adapter cable for BMW R 80 GS / R 100 GS as of 1991 For directly connecting a control lamp unit or a SPORT control lamp unit to a BMW R80GS or R100GS on. Adapter cable R247 030-0036 Crimp Contacts with Socket Shell 12 crimp contacts (socket) with 12 pin socket shell as on control lamp unit (mating part) 030-0031 Crimp Contacts with Connector Shell 12 crimp contacts (pin) with 12 pin connector shell as on control lamp kit. 030-0032 Crimp Contacts with AMP Socket Shell 12 crimp contacts (socket) with 12 pin socket shell needed for connecting a control lamp kit to a BMW R850GS / R1100GS / R1150GS. 030-0037 Crimp Contacts with AMP Connector Shell 8 crimp contacts (pin) with 8 pin socket shell needed for connecting a control lamp to a BMW R80GS / R100GS Please note: Does not fit to the R 80 G/S and the R80 gs basic! 030-0038
Cockpit 25 mm 22 mm 12 mm 1037 Handlebar Clamps 1) 040-0042 (25 mm) 2) 040-0040 (22 mm) 3) 040-0041 (20 mm) 1 2 3 Rubber Mounts 4) 040-0030 4 5 5) 040-0031 Durchmesser 25 mm, Durchmesser 15 mm, 20 mm hoch, 8 mm hoch, Außengewinde M6 Außengewinde M4 Temperature Sensor Adapters 1) 015-0055 (inside thread M10x1,0) 2) 015-0054 (inside thread M10x1,0) 3) 015-0053 (inside thread M10x1,0) 4) 015-0052 (inside thread M10x1,0) 5) 015-0051 (inside thread M10x1,0) 6) 015-0050 (inside thread M10x1,0) 7) 015-0056 M24 x 2.0 F650GS 1. M22x1,5 2. M20x1,5 3. M18x1,5 4. M16x1,5 5. M14x1,5 6. M14x1,25 Temperature Sensors 1) 015-0003 M12 x 1,5 2) 015-0002 M12 x 1,25 3) 015-0001 M10 x 1,0 3 2 1 Magnets 1) 015-0042 M5, 47 mm long 4 3 2 1 2) 015-0043 M5, 12 mm long 3) 015-0044 M4,inside thread 4) 015-0041 diameter 10mm