UREU OF LOCL RODS & STREETS 42-3(2) ICYCLE FCILITIES Jan 2006 MINIMUM CROSS SECTIONS FOR CURED STREETS WITHOUT PRKING (Marked icycle Lanes) Figure 42-3G b. Curbed Streets with Parking. The bicycle lane should be located between the parking lane and the through traffic lane with a minimum bicycle lane width of 5 ft (.5 m); see Figure 42-3H. 2. Shared Roadways. On a shared roadway facility, bicyclists and motorists share the same travel lanes without a striped separation. The majority of urban cross sections fall into this category. Shared roadways have particular application where physical constraints (e.g., buildings, narrow sidewalks, environmentally sensitive areas) preclude widening a street to provide bike lanes. Most shared roadways are unmarked, allowing bicyclists to share the outside lane with motor vehicles, as allowed by the Illinois Compiled Statutes. In some instances, it may be advantageous to sign some urban and rural roadways as bicycle routes when providing continuity to other bicycle facilities or when establishing a touring route. On streets where parking is prohibited, the recommended lane width on two-lane, twoway roadways is 4 ft (4.2 m) excluding flags. However, a width of 3 ft (4.0 m) may be considered acceptable. Use these same widths for the outer lanes of multilane highways where bicycle traffic is allowed.
UREU OF LOCL RODS & STREETS Jan 2006 ICYCLE FCILITIES 42-3(3) MINIMUM CROSS SECTIONS FOR CURED STREETS WITH PRKING Figure 42-3H Where parallel parking is permitted but a parking lane is not provided, the combination lane should be a minimum of 2 ft (3.6 m) wide. If parking volume is substantial or turnover is high, an additional ft or 2 ft (300 mm or 600 mm) of width is desirable. 42-3.03(c) ccommodation on Existing Roads and Streets icycle accommodations can also be adapted to a roadway by marking or remarking the pavement to increase the width of the lane or to add bike lanes. Consider the following: reduce the width of inside traffic lanes; reduce median width, especially with the removal of raised- medians; remove parking possibly in conjunction with providing off-street parking; and/or reduce the number of traffic lanes. This option may be appropriate if, for example, oneway couples are created or if a parallel roadway improvement reduces the traffic demand on an adjacent street that is more suited for bicycle travel.
Illinois SPECIL DESIGN ELEMENTS September 200 Notes:. Where articulated buses are expected to use these stops, add an additional 20 ft (6 m) to the bus distances. 2. Provide an additional 50 ft (5 m) of length for each additional bus expected to stop simultaneously at any given bus stop area. This allows for the length of the extra bus (40 ft (2.2 m)) plus 0 ft (2.8 m) between buses. ON-STREET US STOPS Figure 58-3. 58-3.4 HRD COPIES UNCONTROLLED
Illinois SPECIL DESIGN ELEMENTS September 200 Notes: Stopping area length consists of 50 ft (5 m) for each standard 40 ft (2.2 m) bus and 70 ft (2 m) for each 60 ft (8.3 m) articulated bus expected to be at the stop simultaneously. us turnout width is desirably 2 ft (3.6 m). For posted speeds under 30 mph, a 0 ft (3.0 m) minimum bay width is acceptable. These dimensions do not include width. Suggested taper lengths are listed below. minimum taper of 5: may be used for an entrance taper from an arterial street for a bus turnout while the merging or re-entry taper should not be sharper than 3:. The minimum design for a bus turnout does not include acceleration or deceleration lengths. Recommended acceleration and deceleration lengths are listed below. Design Speed 35 mph 40 mph 45 mph 50 mph 50 km/h 60 km/h 70 km/h 80 km/h Entering Speed* 25 mph 30 mph 35 mph 40 mph 35 km/h 45 km/h 55 km/h 65 km/h cceleration Lengths US CUSTOMRY 250 ft 400 ft 700 ft 975 ft METRIC 60 m 05 m 200 m 30 m Deceleration Lengths ** 85 ft 265 ft 360 ft 470 ft 45 m 70 m 05 m 45 m Suggested Taper Lengths 70 ft 90 ft 20 ft 230 ft 45 m 50 m 60 m 70 m * Desirably, the bus speed at the end of taper should be within 0 mph (5 km/h) of the design speed of the traveled way. ** ased on a 2.5 mph/sec (4.0 km/h/s) deceleration rate. TYPICL US TURNOUT DIMENSIONS Figure 58-3.C HRD COPIES UNCONTROLLED 58-3.5
Illinois SPECIL DESIGN ELEMENTS September 200 RECOMMENDED LENGTHS FOR US-LODING RES (Park-and-Ride Lots) Figure 58-2. HRD COPIES UNCONTROLLED 58-2.7
UREU OF LOCL RODS & STREETS 4-(2) SPECIL DESIGN ELEMENTS Jan 2006 Design Vehicle W L P 30 ft (0 m) 60 ft (20 m) SU 50 ft (5 m) 00 ft (30 m) Design Vehicle R W P 30 ft (0 m) 8 ft (6 m) W-40 (W-2) 42 ft (3 m) 25 ft (8 m) SU & W-50 (W-5) 47 ft (5 m) 30 ft (0 m) CUL-DE-SCS Figure 4-
Illinois SPECIL DESIGN ELEMENTS March 202 If ramps change direction at landings, the minimum landing size shall be 60 in by 60 in (.5 m by.5 m). 4. Handrails. If a ramp run has a rise greater than 6 in (50 mm) or a horizontal projection greater than 72 in (.8 m), then it shall have handrails on both sides. See the applicable accessible guidelines for additional handrail criteria. 5. Cross Slope and Surfaces. The cross slope of ramp surfaces shall preferably be.5% and no greater than 2%. surfaces shall comply with the criteria for Surface of sidewalks; see Section 58-.06. 6. Edge Protection. s and landings with drop-offs shall have s, walls, railings, or extended surfaces that prevent people from slipping off the ramp. Curbs shall be a minimum of 2 in (50 mm) high. Extended surfaces shall extend a minimum of 2 in from the outside of the handrail. 7. Outdoor Conditions. Outdoor ramps and their approaches shall be designed so that water will not accumulate on walking surfaces. Running Slope Maximum Rise 8.3% but 0% ( :2 but :0) 6 in (50 mm) 0% but 2.5% ( :0 but :8) 3 in (75 mm) Note : These dimensions may only be used when space limitations will not fit a standard ramp. Note 2: Running slopes steeper than 2.5% (:8) are not allowed. LLOWLE EXCEPTIONS TO STNDRD RMP DIMENSIONS (Existing Sites, uildings, and Facilities) Figure 58-.E 58-.09 Curb s ramp shall connect sidewalks at each pedestrian street crossing or crosswalk. For the purpose of this section, a pedestrian crosswalk is defined as that portion of a highway or street ordinarily included within the prolongation or connections of lateral lines of sidewalks at intersections. It also includes any portion of a highway or street distinctly indicated as a crossing for pedestrians by lines or other markings on the surface. It does not include such prolonged or connecting lines from an alley across a street. HRD COPIES UNCONTROLLED 58-.
Illinois SPECIL DESIGN ELEMENTS March 202 SIDEWLKS T DRIVEWY PRONS Figure 58-.D 58-.08 s Portions of sidewalks whose running slope exceed 5% and are not following the general grade of an adjacent street or highway are considered ramps (Note: These ramps are different from ramps. See Section 58-.09 for ramps.). The following represents the accessible criteria for ramps:. Running Slope and Rise. s shall have a running slope greater than 5% up to an 8.3% maximum. The maximum rise for any single ramp run shall be 30 in (760 mm). For ramp heights greater than 30 in (760 mm), a series of ramps and landings must be used. s to be constructed on existing building/facility sites or inside existing buildings/facilities may have a running slope which exceeds 8.3% within the rise limitations shown in Figure 58-.E, if space limitations dictate. 2. Width. The minimum clear width of a ramp shall be 36 in (95 mm). Where handrails are provided, the clear width is measured between inside edge of the rails. 3. Landings. s shall have level landings (preferably be.5% and no greater than 2% in all directions) at the bottom and top of each run and shall have the following features: The landing shall be at least as wide as the widest ramp run leading to the landing. The landing length shall be a minimum of 60 in (.5 m). 58-.0 HRD COPIES UNCONTROLLED
Sidewalk width 5 (.52 m) typical, Sidewalk width 5 (.52 m) typical, Side Lower landing 5 (.52 m) max. setback side flare :0 max. Lower 5 (.52 m) max. setback landing Side and side flare side flare and :0 max. and (length not less than 5-6" between ramps preferred) RMPS IN LNDSCPED RE SETCK < 5 Lower landing and See DETIL :0 max. :0 max. and RMPS IN PVED RE SETCK < 5 and See DETIL SECTION - GENERL NOTES SECTION - not required for ramp slopes not required for ramp slopes flatter than :20. ll slope ratios are expressed as units of vertical displacement to units of horizontal displacement (V:H). Illinois Department of Transportation PSSED January, 202 ENGINEER OF POLICY ND PROCEDURES PPROVED January, 202 ISSUED --97 flatter than :20. DETIL (3) Expansion joint 6 Flush with top of (50) roadway and top of sidewalk 2 (50) R Variable thickness SIDE CUR DETIL DTE --2 --08 REVISIONS Completely revised and renamed standard. Switched units to English (metric). See Standard 60600 for details of depressed adjacent to ramp. ll dimensions are in inches (millimeters) unless otherwise shown. PERPENDICULR CUR RMPS FOR SIDEWLKS STNDRD 42400-06 (Sheet of 2) ENGINEER OF DESIGN ND ENVIRONMENT
side flare Setback greater than 5 (.52 m) :0 max. Sidewalk width 5 (.52 m) typical, C Lower landing Side C Sidewalk width 5 (.52 m) typical, C Lower landing C Setback greater than 5 (.52 m) and :0 max. and RMP IN LNDSCPED RE SETCK > 5 side flare RMP IN PVED RE SETCK > 5 Lower landing and See DETIL SECTION C-C not required for ramp slopes flatter than :20. Illinois Department of Transportation PSSED January, 202 ENGINEER OF POLICY ND PROCEDURES PPROVED January, 202 ENGINEER OF DESIGN ND ENVIRONMENT ISSUED --97 PERPENDICULR CUR RMPS FOR SIDEWLKS STNDRD 42400-06 (Sheet 2 of 2)
Sidewalk width 5 (.52 m) typical, 5 x5 (.52x.52 m) typical, 4 x4 (.22x.22 m) min. 5 x5 (.52x.52 m) typical, 4 x4 width 5 (.52 m) typical, Side and Clear maneuvering area 4 x4 (.22x.22 m) min. 24 (60) min. width 5 (.52 m) typical, side flare 24 min. (60) side flare :0 max. :0 max. (.22x.22 m) min. and 24 min. (60) Clear maneuvering area 4 x4 (.22x.22 m) min. 24 (60) min. 24 (60) min. 24 (60) min. RMP IN LNDSCPED RE RMP IN PVED RE 6 (50) Flush with top of roadway and top of sidewalk and GENERL NOTES This Standard shall only be used for radii of 20 ft. (6. m) or greater. Variable 2 (50) R :20 min. ll slope ratios are expressed as units of vertical displacement to units of horizontal displacement (V:H). thickness SIDE CUR DETIL (3) SECTION - See DETIL See Standard 60600 for details of depressed adjacent to ramp. ll dimensions are in inches (millimeters) unless otherwise shown. Illinois Department of Transportation PSSED January, 202 ENGINEER OF POLICY ND PROCEDURES PPROVED January, 202 ISSUED --2 DETIL Expansion joint DTE REVISIONS --2 New standard. DIGONL CUR RMPS FOR SIDEWLKS STNDRD 424006 ENGINEER OF DESIGN ND ENVIRONMENT
Sidewalk width 5 (.52 m) typical, Side where required Side where required Lower landing 5 x5 (.52x.52 m) typical, 4 x4 (.22x.22 m) min. Lower landing and See DETIL SECTION - and CORNER PRLLEL CUR RMP Lower landing (3) SECTION - (s) not required for ramp slopes flatter than :20. 6 Flush with top of GENERL NOTES ll slope ratios are expressed as units of vertical displacement to units of horizontal displacement (V:H). (50) roadway and top of sidewalk See Standard 60600 for details of depressed adjacent to ramp. Illinois Department of Transportation PSSED January, 202 ENGINEER OF POLICY ND PROCEDURES PPROVED January, 202 ISSUED --2 DETIL Expansion joint 2 (50) R Variable thickness SIDE CUR DETIL DTE REVISIONS --2 New standard. ll dimensions are in inches (millimeters) unless otherwise shown. CORNER PRLLEL CUR RMPS FOR SIDEWLKS STNDRD 4240 ENGINEER OF DESIGN ND ENVIRONMENT
Face of building, Face of side, C where applicable Lower landing when required 5 x5 (.52x.52 m) 5 (.52 m) typical 4 (.22 m) minimum Sidewalk width 5 (.52 m) typical, side flare in paved areas typical, 4 x4 (.22x.22 m) min. Side in landscaped Sidewalk width 5 (.52 m) typical, typical areas :0 max. and PRLLEL MID-LOCK CUR RMP and C PERPENDICULR MID-LOCK CUR RMP Sidewalk, Lower landing,, Sidewalk Side where required SECTION - (s) not required for ramp slopes flatter than :20. Lower landing and and See DETIL :20 min. See DETIL SECTION - 6 (50) Flush with top of roadway and top of sidewalk SECTION C-C GENERL NOTES ll slope ratios are expressed as units of vertical displacement to units of horizontal displacement (V:H). See Standard 60600 for details of depressed adjacent to ramp. ll dimensions are in inches (millimeters) Illinois Department of Transportation PSSED January, 202 ENGINEER OF POLICY ND PROCEDURES PPROVED January, 202 ISSUED --2 2 (50) R Variable thickness SIDE CUR DETIL DETIL (3) Expansion joint DTE REVISIONS --2 New standard. unless otherwise shown. MID-LOCK CUR RMPS FOR SIDEWLKS STNDRD 42406 ENGINEER OF DESIGN ND ENVIRONMENT