Dul Mnitr Desk Munt Instructin Mnul SKU: STAND-V002 Scn the QR cde with yur mbile device r llw the link r helpul vides nd speciictins relted t this prduct. https://viv-us.cm/prducts/stnd-v002 help@viv-us.cm www.viv-us.cm 1-800-371-5654
WARNING! I yu d nt understnd these directins, r i yu hve ny dubts but the sety the instlltin, plese cll quliied technicin. Check creully t mke sure there re n missing r deective prts. Imprper instlltin my cuse dmge r serius injury. D nt use this prduct r ny purpse tht is nt explicitly speciied in this mnul. D nt exceed weight cpcity. We cnnt be lible r dmge r injury cused by imprper munting, incrrect ssembly r inpprprite use. TOOLS NEEDED Phillips Screwdriver ASSEMBLY STEPS DO NOT EXCEED WEIGHT CAPACITY. Filure t d s my result in serius injury. 22 lbs Per Arm (10kg) TIPOVER WARNING SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER: NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND. USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER. STEP 1 Optin A: Desk Clmp Instll 1. Instll the clmp brce (C) t the ple (A) using x3 M5x14 blts (F). See Figure 1. 2. Attch st pd (T1) t the clmp brce (C), see Figure 2. 3. Instll the clmp (B) t the ple ssembly ccrding t the thickness the desktp. The thickness cn be chnged t 3 psitins. Cnnect using x2 M8x12 blts (G) nd tighten using the Allen key (O). Tighten the clmp t the desktp using the plstic knb. See Figure 3. WARNING: CHOKING HAZARD SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED. PACKAGE CONTENTS c Figure 1 t1 Figure 2 g b Plstic Knb Figure 3 A (x1) Ple B (x1) Clmp C (x1) Clmp Brce D (x1) Swivel Arm E (x2) VESA Plte F (x3) M5x14 Blt G (x2) M8x12 Blt H (x2) Nut I (x1) M10 Blt J (x1) Supprt Plte Optin B: Grmmet Bse with Existing Hle I existing grmmet hle cmes with plstic prtectr, remve it t ensure lt surce bere instlling the desk munt. m K (x1) M10 Wsher O (x1) Allen Key Set L (x1) Spring Wsher P (x1) Wrench M (x1) Grmmet Bse Plte Q (x8) M4x12 Thumb Blt N1 (x1) Wire Clip R (x8) M4x30 Blt N2 (x4) Wire Clip S (x8) M4 Spcer 1. Instll grmmet bse plte (M) t the ple (A) using x3 M5x14 blts (F). See Figure 4. 2. Attch st pd (T2) t the grmmet bse plte (M), see Figure 5. 3. Psitin ple (A) n the munting surce nd secure using the supprt plte (J), M10 wsher (K), spring wsher (L) nd M10 blt (I). Fsten M10 blt using prvided wrench (P). See Figure 6. Figure 4 t2 Figure 5 j T1 (x1) St Pd T2 (x1) St Pd l k i Figure 6 NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED 2 3
STEP 1 (cntinued) STEP 3 Optin C: Grmmet Bse with Sel-Drilled Hle 1. Psitin the Ple (A) n the munting surce nd mrk the center hle. Drill 3/8 (10mm) dimeter hle t the mrked psitin thrugh the munting surce. 2. Instll the Grmmet Bse Plte (M) t the Ple (A) using x3 M5x14 Blts (F), nd tighten using the Allen Wrench (O), see Figure 7. 3. Attch St Pd (T2) t the Grmmet Bse Plte (M), see Figure 8. 4. Psitin the Ple (A) n the munting surce nd secure using Supprt Plte (J), M10 Wsher (K), Spring Wsher (L), nd M10 Blt (I). Fsten the M10 Blt using prvided Wrench (P), see Figure 9. m Figure 7 t2 Figure 8 j k l i Figure 9 OPTION A: Flt Bck Mnitr Attch the VESA plte (E) t the mnitr with M4x12 thumb blts (Q). NOTE: Hnd tighten screws t vid ver tightening. q OPTION B: Curved Bck Mnitr Attch the VESA plte (E) t the mnitr with M4x30 blts (R) nd M4 spcers (S). NOTE: Hnd tighten screws t vid ver tightening. s r STEP 2 Instll swivel rm (D) t the ple (A). Fsten the blt with supplied Allen key (O). Attch the wire clip (N1,N2) t the ple (A) nd swivel rm (D). STEP 4 Slide the mnitr nt the hed swivel rm (D). Instll the security nut (H). Mke sure the security nut is instlled bere yu rtte the mnitr. Fr minr height djustment, use Allen key (O). d n2 n1 h 4 5
STEP 5 STEP 6 Tighten the blt with the supplied Allen key (O) t ix the tilt ngle. Use the supplied Allen key set (O) t mke ny necessry djustments. Mnge cbles nd stre Allen keys (O) in wire clip (N1) r uture use. T level the mnitrs, remve the nut (H) nd turn the blt with the Allen key (O) t rise r lwer the mnitr. Replce nut (H) ter the djustment. n1 6 7
Lve yur new VIVO setup nd wnt t shre? Tg us in yur pht! @viv_us Lst Updted: 11/05/2018 I ny prts re received dmged r deective, plese cntct us. We re hppy t replce prts t ensure yu hve ully unctining prduct. help@viv-us.cm www.viv-us.cm 1-800-371-5654 Fr mre VIVO prducts, check ut ur website t: www.viv-us.cm.