INSTRUCTION MANUAL AIRBRUSH COMPRESSOR AS-48A Thanks for purchasing our airbrush compressor and please read this Instruction Manual carefully and thoroughly before operating the tool to get best performance.
1. Features: 1. Air tank, providing smooth air flow, zero pulse. 2. Four cylinder, supply high air flow for many airbrushes. 3. Oil free, piston type; No air polluted. 4. With water filter, pressure adjustor and pressure gauge. 5. Double air pressure switch. Switch 1, low pressure auto stop switch, for airbrush purpose. Switch 2, high pressure none stop switch, for other high pressure air tools. 6. Auto release air pressure function, start without any pressure, prolong the motor life. 7. Thermally protected inside. 8. Safety protect devices for air tank. 9. Can operate with small air nailer tools, spray gun. 2. Data Sheet: Airbrush compressor AS-48A, suitable for big nozzle airbrush, even can operate with two airbrush at the same time, can be widely used in craftwork spraying, cosmetics, tattoo, tanning, hobbies/models, fingernail painting. It can be also used for providing air source for medical, environment protect, breed aquatics Industrial, food Industrial, chemical industrial, laboratory and so on. 2
3. Specification: Type: Four cylinder air compressor with tank with cover. Power: 1/4 HP Speed: 1450/1700 r.p.m Air flow: 70-78 L/min Double switch: switch 1: Auto start at 3 bar, Auto stop at 4 bar. switch 2: Max pressure at 6 bar. Pressure adjust range: 0~6 bar Air tank: 4.0L Weight: 8.4 KG Dimension: 38.5X20.5X32.5mm Suitable for all kinds of airbrush. 4. Operation directory: 1. Usually the outlet thread size of our air compressor is 1/8'' BSP. If you need the 1/4'' BSP or other NPT screw thread, you should get the other adapters to fix the outlet, then you can connect with different air hoses. 2. The original air hose have rubber airproof inside and the user can make the airtight by hand to and get good performance. If the air hose is not the original, the air hose and air compressor may be not well airproof. However, 3
100% airtight is only effective for auto stop function air compressor. Seal thread tape can be used to prevent leakage, it could be got in all the stores selling sanitary products. 3. Connect the air compressor, air hose and airbrush (or other air tools), plug into the mains supply, turn on the switch, then the air compressor will start work. The press gauge will show the max pressure, and you can adjust the working pressure by adjusting the pressure adjustor. 4. Checking the air leakage. Please do not use any air tools firstly before the compressor reach the maximum pressure and observe whether it will be auto-stop. If the compressor will not be auto-stop, please turn off theswitch, then check the index on pressure gauge, if it is very steady, means the airtight is very good; While the index decline down quickly, it means there has the air leakage in the area of the connection. Please check and make it airtight, because any small leakage will affect the performance of the compressor. (It may lead to frequently auto-stop and auto-start). 5. The difference between maximum pressure and working pressure. The compressor' maximum pressure is the highest pressure it can build up, and the working pressure is the one shown on the pressure gauge When the connected airbrush is opened. Apparently, the working pressure is the constant pressure the compressor can maintain during airbrushing. The level of this working pressure depends on the nozzle diameter of the airbrush to which it is connected; the larger the nozzle diameter, the bigger the amount 4
of air which can escape and the lower the compressor's working pressure. 6. The compressors have tank which can store compress air before delivery to the airbrush (or other air tools). The tank is very useful, and the advantage is follows: a. Tanks provide a reservoir of pressurized air that you can draw from while you're spraying. b. You can draw air at a regulated pressure from the tank instead of the average pressure of the piston cylinders. c. Because you're drawing air from the tank, then can eliminate the tiny pulsation in the air supply caused by the physical motion of pistons pressurizing air. d. The life of the compressor engine increases because it makes air as the tank needs instead of always being on. e. Tanks are great first line moisture traps. 5. Notice: 1. The users should choose the right air compressor with suitable air flow and pressure according to the actual work requirement. 2. Before connecting the compressor, check the main voltage compatible with the electrical characteristics of the motor. 3. Please follow local electrical rules, and safety rules. And use the socket 5
which must be earthing. 4. Never leave the appliance exposed to dust, acids, vapors, explosive or flammable gasses or atmospheric agents (rain, sun, fog, snow). 5. The vacuum pump must be used in suitable environments (well-ventilated, with an ambient temperature between +5 and +40. 6. Never use the appliance in your bare feet or wet feet, as well as the wet hand. 7. Never allow the children to touch the working machine or insert the stick into the machine. It will cause the danger of scald or get an electric shock. 8. Do not open or tamper with any part of the compressor. Contact an authorized Service Center. 9. Please release the water by opening the water drain valve under the tank when the compressor does not use for long time. Store the compressor in well ventilated and dry place. 10. In order to prolong the compressor life of the dual pressure ones, please turn off the compressor if the user do not use the air for long time under high pressure continuous working switch. 6.SPARE PART LIST: 6
7
NO. PARTS NO. DESCRIPTION Q'TX PARTS NO. DESCRIPTION Q'TX NO. 1 AS-48A #01 POWER SWITCH 1 34 AS-48A--#34 HANDGRIP 1 2 AS-48A--#02 REAR COVER 1 35 AS-48A--#35 FILTER VALVE 1 3 AS-48A--#03 WIRE 1 36 AS-48A--#36 INLET VALVE ROB1 1 4 AS-48A-#04 CONDENSER 1 37 AS-48A--#37 INLET VALVE ROB2 1 5 AS-48A--#05 COUNTER WEIGHT 2 38 AS-48A--#38 AIR TANK 1 6 AS-48A--#06 REAR BODY 1 39 AS-48A--#39 NUT 4 7 AS-48A--#07 RETAINIER RING 2 40 AS-48A--#40 RUBBER PAD 4 8 AS-48A--#08 STATIONARY MOTOR 1 41 AS-48A--#41 SCREW 4 9 AS-48A--#09 BEARING 2 42 AS-48A--#42 DRAIN VALVE 1 10 AS-48A--#10 ROTARY MOTOR 1 43 AS-48A--#43 SAFELY VALVE 1 11 AS-48A--#11 FRONT BODY 1 44 AS-48A--#44 CONNECT SCREW 1 12 AS-48A--#12 RUBBER PAD 2 45 AS-48A--#45 AIR SPUTTER 1 13 AS-48A--#13 SCREW 4 46 AS-48A--#46 PRESSURE SWITCH 1 14 AS-48A--#14 SCRW 4 47 AS-48A--#47 O-RING 2 15 AS-48A--#15 NUT 4 48 AS-48A--#48 COMPRESSION NUT 2 16 AS-48A--#16 CONNECTING ROD 4 49 AS-48A--#49 HOSE 1 17 AS-48A--#17 COMPRESSION RING 4 50 AS-48A--#50 OUTLET VALVE ROB2 1 LOCK PLATE NON-TERURN VALVE 18 AS-48A--#18 4 51 AS-48A--#51 COVER 1 19 AS188--#19 SCREW 4 52 AS-48A--#52 MUSHROON SEALED TAPE 1 CYLINDER NON-RETURN VALVE 20 AS-48A-#20 4 53 AS-48A--#53 BODY 1 21 AS-48A--#21 O-RING 4 54 AS-48A--#54 3-OUTLET VALVE 2 22 AS-48A--#22 CYLINDER BLOCK 4 55 AS-48A--#55 ALUMINIUM CONNECTOR 2 23 AS-48A--#23 O-RING 4 56 AS-48A--#56 O-RING 2 8
24 AS-48A--#24 CYLINDER HEAD 4 57 AS-48A--#57 COMPRESSION NUT 2 25 AS-48A--#25 SCREW 16 58 AS-48A--#58 HOSE 1 26 AS-48A--#26 SCREW 4 59 AS-48A--#59 FILTER SCREEN 1 27 AS-48A--#27 FRONT COVER 1 60 AS-48A--#60 O-RING 1 28 AS-48A--#28 SCREW 8 61 AS-48A--#61 SOLENOID VALVE 1 SCREW NON-RETURN AIR INLET 29 AS-48A--#29 4 62 AS-48A--#62 VALVE 4 30 AS-48A--#30 HAND GRIP BASE 2 63 AS-48A--#63 O-RING 4 31 AS-48A--#31 SCREW 2 64 AS-48A--#64 COMPRESSION NUT 4 32 AS-48A--#32 NUT 2 65 AS-48A--#65 AIR OUTLET SCREW 4 33 AS-48A--#33 RETAINIER RING 2 66 AS-48A--#66 7 Air compressor structure A. POWER PLUG B. PRESSURE REGULATOR C. PRESSURE GAUGE D. CONNECTION E. AIR FILTER DOUBLE SWITCH: SWITCH1: AUTO START AT 3 BAR AUTO START AT 4 BAR SWITCH2: MAX PRESSURE AT 6 BAR 9