SAFETY DATA SHEET 6801 St. Rt. 60 WHIZ-LUBE SPRAY Birmingham, Ohio 44889

Similar documents
Safety Data Sheet HAYNES SILICONE SPRAY Haynes Manufacturing Company

Product Name: Safe Seal Print Date: 10/9/18 Product Code: Total pages: Page 1 of 6 SAFETY DATA SHEET. 1. Product and Company Identification

MATERIAL SAFETY DATA SHEET

Product Name: IMS 15% Print Date: 3/16/18 Product Code: Total pages: Page 1 of 6 SAFETY DATA SHEET. 1. Product and Company Identification

SAFETY DATA SHEET. 1. Product and Company Identification

Product Name Free All Print Date: 7/28/17 Product Code: Total pages: Page 1 of 6 SAFETY DATA SHEET. 1. Product and Company Identification

Material Safety Data Sheet

Product Name: Economy Mold Cleaner Product Code: Total pages: Page 1 of 7 SAFETY DATA SHEET. 1. Product and Company Identification

Product Name Foaming Rust Inhibitor Print Date: 7/28/17 Product Code: Total pages: Page 1 of 6 SAFETY DATA SHEET

Product Name: White 2000 Print Date: 10/9/18 Product Code: , Total pages: Page 1 of 7 SAFETY DATA SHEET

Product Name: IMS Silicone Sprays Product Code: , , , , Total pages: Page 1 of 7 SAFETY DATA SHEET

Product NameWhite Lithium Print Date: 10/9/18 Product Code: Total pages: Page 1 of 6 SAFETY DATA SHEET. 1. Product and Company Identification

Material Safety Data Sheet

MATERIAL SAFETY DATA SHEET

Product Name TDL Print Date: 6/11/15 Product Code: 16-TDL Total pages: Page 1 of 7 SAFETY DATA SHEET. 1. Product and Company Identification

1. Product And Company Identification

Product Name: Corrosion Stop Print Date: 4/12/17 Product Code: 16-CSP Total pages: Page 1 of 7 SAFETY DATA SHEET

AST PENETRANT II SAFETY DATA SHEET Section 1- Product and Company Identification

24 Hour Emergency CHEMTREC

BUDGET MOLDERS SUPPLY, INC CORPORATE PARK DRIVE MACEDONIA, OHIO MATERIAL SAFETY DATA SHEET MSDS NO.: DATE: May 22, 2007

Air Tool Lubricant MSDS. Air Tool Lubricant. (800) (Poison Control USA) 24 Hours (800) (CHEMTREC) 24 Hours. Not Applicable - Mixture

IDQ Operating, Inc. 44 Old Ridgebury Road Suite 300 Danbury, CT Tel Product And Company Identification

Safety Data Sheet Compound

SAFETY DATA SHEET FOR FALK GMAX 6000

Sawyer Insect Repellent. No significant adverse health effects are expected to occur upon short-term exposure

SAFETY DATA SHEET Lead Stop

Classification of the substance or mixture This chemical is considered hazardous by the None

1. Product And Company Identification

5115 Hadley Ave. N., St. Paul, MN T: F: SAFETY DATA SHEET. 1. Product and Company Identification

SAFETY DATA SHEET (800) (800) Category 2 Category 2A

Safety Data Sheet Revised 16 November 2015

Safety Data Sheet 1782SYM

Safety Data Sheet. Address GHS Precautions If skin irritation occurs: Get medical advice/attention

SAFETY DATA SHEET SECTION 1 IDENTIFICATION. MB4908 Product Line

Safety Data Sheet 1797SYM

SAFETY DATA SHEET. Orang-Sol 300. MANUFACTURER 24 HR. EMERGENCY TELEPHONE NUMBERS Detco Industries, Inc.

SAFETY DATA SHEET. MANUFACTURER 24 HR. EMERGENCY TELEPHONE NUMBERS Nova Pressroom Products

SAFETY DATA SHEET. CU-8120 Enzyme & bacteria digestive powder. None. (800) (800) Category 5 Category 3 Category 2B

Product Name: Items: Formula Code: SDS Revision Date:

Material Safety Data Sheet

IDQ Operating, Inc. 44 Old Ridgebury Road Suite 300 Danbury, CT Tel Product And Company Identification

Safety Data Sheet EPI-CLENZ FOAMING INSTANT HAND SANITIZERS

ALL-PURPOSE 4-WAY, Aerosol Lubricant / Penetrant SAFETY DATA SHEET Section 1- Product and Company Identification

MATERIAL SAFETY DATA SHEET 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION 2. COMPOSITION/INFORMATION ON INGREDIENTS

Use only for the purpose on the product label.

SAFETY DATA SHEET (800) (800) Category 3 Category 2A

SAFETY DATA SHEET (800) (800) Category 2 Category 2A

Safety Data Sheet 1818BR

SAFETY DATA SHEET. CALLOUS CUTTER Revision 01/30/ PRODUCT AND COMPANY IDENTIFICATION 2. HAZARDOUS IDENTIFICATION

Safety Data Sheet Lyden Oil Company

Date Printed: 2/17/2019 Product: M UPHOLSTERY/FABRIC CLEANER. Surface Preparation or Protection

SAFETY DATA SHEET. Section 1. IDENTIFICATION

Safety Data Sheet 1421

Safety Data Sheet LPS300 and LPS301

Material Safety Data Sheet

Safety Data Sheet Revised 16 November 2015

Product Name: IMS Zinc Stearate Product Code: Total pages: Page 1 of 7 SAFETY DATA SHEET. 1. Product and Company Identification

RMR Botanical Surface Cleaner and Treatment Safety Data Sheet

1. Product And Company Identification

SAFETY DATA SHEET WHITE FOAM DETERGENT CONCENTRATE

CHEMICAL & FERTILIZER, LLC Safety Data Sheet Section 1 Chemical Product and Company Identification

S A F E T Y D A T A S H E E T

Signal Word:Danger N/A

Safety Data Sheet Bulldog Durex EPDM Rinseable Primer #115

SAFETY DATA SHEET. Lemon Oil Furniture Polish. 1. Product and Company Identification. 2. Hazards Identification

SAFETY DATA SHEET CERAMIC GLAZE

Safety Data Sheet Lyden Oil Company

SAFETY DATA SHEET. Allied Food Grade AW 68 SECTION 1: PRODUCT IDENTIFICATION

Safety Data Sheet Lyden Oil Company

NO THAW FREEZER/COOLER CLEANER. Use only for the purpose on the product label.

: True Brand Stop Leak

Safety Data Sheet 1628SYM

2. HAZARDS IDENTIFICATION GHS Classification: Acute oral toxicology 5, Acute dermal toxicaology 5, specific target organ toxicology 2

Safety Data Sheet Lyden Oil Company

SAFETY DATA SHEET. Section 1: Company and Product Identification. Section 2: Hazard(s) Identification. Section 3: Product Composition

MATERIAL SAFETY DATA SHEET C-MUL SUN DRILLING PRODUCTS CORP.

Aerosol Portion: faster than butyl acetate;immediate at temperatures above -35 C. Liquid Portion: slower than butyl acetate.

MATERIAL SAFETY DATA SHEET

SAFETY DATA SHEET. CLASSIFICATION SIGNAL WORD: Hazard Statements. Precautionary Statements

SAFETY DATA SHEET. Section 1: Company and Product Identification. Section 2: Hazard(s) Identification

SAFETY DATA SHEET(SDS)

Use only for the purpose on the product label.

Safety Data Sheet Lyden Oil Company

WARNING: Flammable liquid and vapor.

SAFETY DATA SHEET SECTION 1 IDENTIFICATION

Safety Data Sheet Page 1 of 6 Repel Natural Insect Repellent 2 Revision date: 5/18/2016

Safety Data Sheet 1452SYM

BT-701. Advanced Chemical Technology, Inc. SAFETY DATA SHEET Version 1.0 Effective Date: 06/01/15 1. PRODUCT AND COMPANY IDENTIFICATION

SAFETY DATA SHEET 1. IDENTIFICATION 2. HAZARDS IDENTIFICATION. Product Identifier. Additional Identification Product Code: Synonyms: 19015

SAFETY DATA SHEET. Product Name: LIQUID SEAWEED CONCENTRATE #3. Page 1 of 5. Classification of the Substance or Mixture. Label Elements.

Product Name: IMS Zinc Stearte Print Date: 8/9/18 Product Code: Total pages: Page 1 of 6 SAFETY DATA SHEET

Safety Data Sheet 1225BR

Safety Data Sheet 1565BR

EXPRESS GEL HAND SANITIZER. Use only for the purpose on the product label.

12/14/2017 EN (English US) 1/5

Material Safety Data Sheet MUELLER HINTON AGAR 500GM. Section 1 - Chemical Product and Company Identification

SAFETY DATA SHEET. Section 1: Product Identification. Section 2: Hazard(s) Identification

Safety Data Sheet Lyden Oil Company

Safety Data Sheet Lyden Oil Company

Material Safety Data Sheet

Transcription:

SECTION 1 PRODUCT IDENTIFICATION PRODUCT NAME: WHIZ-LUBE SPRAY PRODUCT TYPE: Aerosol PRODUCT USE: Industrial Lubricant PRODUCT CODES: 173518 11.25 oz. Can NSF #125110 H1 EMERGENCY PHONE NUMBERS: 800-535-5053 Domestic (INFOTRAC) 352-323-3500 International (INFOTRAC) NOTE: The information contained herein is accurate to the best of our knowledge. We do not suggest or guarantee that any hazards listed herein are the only ones which exist. We provide this information as guidance for providing personal protection to your employees. The user has the sole responsibility to determine the suitability of the materials for any use and the manner of use contemplated. The user must meet all applicable safety and health standards. SECTION 2 HAZARD IDENTIFICATION Classification of substance or mixture: Flammable Aerosols Category 1 Gases under pressure Liquefied gas Skin Irritation Category 2 Specific target organ (single exposure) Category 3 Aspiration Hazard Category 1 Pictograms: Signal Word: Danger H222 Extremely Flammable aerosol H280 Contains gases under pressure; may explode if heated H315 Causes skin irritation H336 May cause drowsiness or dizziness H304 May be fatal if swallowed and enter airways Precautionary Statements: Prevention: P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P211 Do not spray on an open flame or other ignition source. P251 Pressurized container: Do not pierce or burn, even after use. P261 Avoid breathing dust/fume/gas/mist/vapours/ spray P264 Wash thoroughly after handling. P271 Use only outdoors or in well-ventilated place P280 Wear protective gloves 1

Response: P301+P310 If Swallowed: Immediately call a poison center or doctor P331 Do NOT induce vomiting P304+P340 If Inhaled: Remove victim to fresh air and keep at rest in a position comfortable for breathing. P312 Call a poison center/doctor if you feel unwell. P302+P352 If on skin: Wash with plenty of soap and water P362+P364 Take off contaminated clothing and wash it before reuse. P332+P313 If skin irritation occurs: Get medical advice/attention P403 Store in well ventilated place P405 Store locked up P410+P412 Protect from sunlight. Do not expose to temperatures exceeding 50 C/122 F P501 Dispose of contents/container in accordance with local/regional regulations. SECTION 3 COMPOSITION INFORMATION ON INGREDIENTS Ingredients CAS # Percent Trade Secret Liquefied Petroleum Gas 68476-86-8 15-30 % * Petroleum Grease 8009-03-8 70-95% * Isoparaffinic Hydrocarbon 64741-66-8 8-15% * *The exact percentage (concentration) of composition has been withheld as a trade secret. SECTION 4 FIRST AID MEASURES Eye Contact: Flush with warm water for 15 minutes. Seek medical attention. Skin Contact: Wash with soap and water. Remove any contaminated clothing and launder before reusing. If irritation persists, seek medical attention. Inhalation: Remove exposed individual to fresh air, protecting yourself. Restore breathing if necessary. Contact a physician. Ingestion: Do not induce vomiting. Get medical attention immediately. DO NOT GIVE AN UNCONCIOUS OR CONVULSING PERSON ANYTHING BY MOUTH! SECTION 5 FIRE FIGHTING MEASURES Flash Point: Flash point of propellant <0 degrees F. 2

Flammable limits in air, % by volume: Upper: 9.5% (VOL.) Gas in air (propellant portion) Lower: 1.8 % (VOL.) Gas in air (propellant portion) Extinguishing Media: Dry chemical, carbon dioxide, halon, or foam is recommended. Water spray may be used to cool containers or structures. Halon may decompose into toxic materials and carbon dioxide will displace oxygen, take proper precautions when using these materials. Unusual Fire & Explosion Hazards: This material may be ignited by extreme heat, sparks, flames or other ignition sources (static electricity). Vapors are heavier than air and will collect in low areas (sewers) or travel considerable distances. If containers are not cooled in a fire, they may rupture and ignite. Special Fire Fighting Procedures: At elevated temperatures (over 130F) aerosol container may burst, vent or rupture; use equipment or shielding to protect personnel. Cooling exposed containers with streams of water may be helpful. Emergency responders should wear self-contained breathing apparatus. Wear other protective gear as conditions warrant. Keep unauthorized people out and try to contain spills or leaks if it can be done safely. Material will float on water, avoid spreading the fire. SECTION 6 ACCIDENTAL RELEASE MEASURES Spill or Leak Instructions: Contain spill with dikes of soil or nonflammable absorbent to minimize contaminated area. Avoid run-off into storm sewers and ditches leading to waterways. If required, notify state and local authorities. Place leaking containers in well-ventilated area. Clean up small spills by using a nonflammable absorbent or flushing sparingly with water. Contain larger spills with nonflammable diking or absorbent. Clean up by vacuuming or sweeping. Keep unnecessary people away; isolate hazard area and deny entry. Stay upwind; keep out of low areas. Assess the spill situation, as the spill may not evolve large amounts of hazardous airborne contaminants in many outdoor spill situations. It may be advisable in some cases to simply monitor the situation until spilled product is removed. SECTION 7 HANDLING AND STORAGE Handling: Store below 120 F in cool, dry area, out of direct sunlight and away from strong oxidizers. Do not puncture or burst. Use in accordance with good work place practices. Use with adequate ventilation. Keep containers closed when not in use. Always open containers slowly to allow any excess pressure to vent. Avoid breathing vapor. Avoid contact with eyes, skin or clothing. Wash thoroughly with soap and water after handling. Decontaminate soiled clothing thoroughly before re-use. Destroy contaminated leather clothing. 3

Empty containers may contain residues from the product. Treat empty containers with the same precautions as the material last contained. Do not cut, weld or apply heat to empty containers. Do not incinerate Storage: Store in a cool, dry area, away form heat or direct sunlight. Keep containers closed when not in use. Do not store with incompatible materials SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION Protective Equipment: Use synthetic gloves if necessary to prevent excessive skin contact. Do not wear contacts and always use ANSI approved safety glasses or splash shield. Engineering Controls: General or dilution ventilation is frequently sufficient as the sole means of controlling employee exposure. Local ventilation is usually preferred. Use a NIOSH approved respirator if ventilation is not adequate to maintain exposures below TLV levels. Respiratory Protection: Use adequate ventilation to maintain exposure limits. If the exposure limits of the products or any of its components is exceeded, an approved organic vapor mask should be used (consult your safety equipment supplier). Above 1000 ppm, an approved self-contained breathing apparatus or airline respirator with full face-piece is required Other Suggested Equipment: Eye wash station and emergency showers should be available. Spill containment equipment should be available. Discretion Advised: We take no responsibility for determining what measures are required for personal protection in any specific application. The general information should be used with discretion. Exposure guidelines: Ingredients CAS # Percent Exposure Limits Liquefied Petroleum Gas 68476-86-8 15-30 % OSHA (PEL) 1000 ppm ACGIH TLV 1000 ppm Petroleum Grease (mist) 8009-03-8 70-95% ACGIH (TWA) 5 mg/m3 OSHA (TWA) 5 mg/m3 Isoparaffinic Hydrocarbon 64741-66-8 8-15% Supplier 300 ppm 4

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES Appearance: Amber as dispensed from aerosol can. Odor: Petroluem Evaporation Rate: Ether = 1 Slower PH: NA Melting/Freezing Point: NE Initial Boiling Point And Boiling Range: NE Flash Point: Flash point of propellant <0 F Flammability: NA Vapor Pressure: >30 psi Vapor Density: >1 (Air=1) Relative Density: NE Solubility: Negligible Partition Coefficient: NE Auto-Ignition Temperature: NE Decomposition Temperature: NE Viscosity: NA Flammable Limits In Air, % By Volume: (Propellant Portion) Upper: 9.5%(vol) Gas in Air Lower:1.8% (vol) Gas in Air SECTION 10 STABILITY AND REACTIVITY Stability: Conditions To Avoid: Incompatibility: Hazardous Decomposition: Hazardous Polymerization: Stable Heat, spark, and open flame Strong-Oxidizing Agents Combustion will produce Carbon Monoxide, Carbon Dioxide and nitrogen-oxygen compounds. Will not occur SECTION 11 TOXICOLOGICAL INFORMATION Component Toxicological Information: Information ontoxicological Effects of Components Isoparaffinic Hydrocarbon Acute toxicity Inhalation LC50 Rat > 21mg/l 4h Ingestion LD50 Rat >5,000 mg/kg Dermal LD50 Rabbit >2000 mg/kg Propane Target Organs: No systemic or neurotoxic effects were noted in rats exposed to concentrations of propane as high as 12,000 ppm for 28 days. Reproductive Toxicity: No adverse reproductive or developmental effects were observed in rats exposed to propane; no observed adverse effect level = 12,000 ppm. 5

Isobutane Target Organs: No systemic or neurotoxic effects were noted in rats exposed to concentrations of isobutene as high as 9,000 ppm for 28 days. Reproductive Toxicity: No adverse developmental effects were observed in rats exposed to isobutene as high as 9,000 ppm. Fertility and mating indices may have been affected at 9000 ppm but no effects were observed at 3000 ppm SECTION 12 ECOLOGICAL INFORMATION Isoparaffinic Hydrocarbon Expected to be toxic to aquatic organisms. May cause long-term adverse effects in the aquatic environment. Test Duration Organism Type Test Results Aquatic - Acute Toxicity 96 hour(s) Oncorhynchus mykiss LL50 18.4 mg/l: data for the material Aquatic - Acute Toxicity 48 hour(s) Daphnia magna EL50 2.4 mg/l: data for similar materials Aquatic - Acute Toxicity 72 hour(s) Pseudokirchneriella subcapitata NOELR 6.3 mg/l: data for similar materials Aquatic - Chronic Toxicity 21 day(s) Daphnia magna NOEC 0.17 mg/l: data for similar materials Aquatic Chronic Toxicity 21 day(s) Daphnia magna LOEC 0.32 mg/l: data for similar materials Aquatic - Acute Toxicity 72 hour(s) Pseudokirchneriella subcapitata EL50 29 mg/l: data for similar materials Petroleum gases will readily evaporate from the surface and would not be expected to have significant adverse effects in the aquatic environment. Classification: No classified hazards. SECTION 13 DISPOSAL CONSIDERATIONS Do not puncture or burn containers. Give empty, leaking, or full containers to disposal service equipped to handle and dispose of aerosol (pressurized) containers. Dispose of spilled material in accordance with state and local regulations for waste that is non-hazardous by Federal definition. Note that this information applies to the material as manufactured; processing, use, or contamination may make this information inappropriate, inaccurate, or incomplete. Note that this handling and disposal information may also apply to empty containers, liners and rinsate. State or local regulations or restrictions are complex and may differ from federal regulations. This information is intended as an aid to proper handling and disposal; the final responsibility for handling and disposal is with the owner of the waste. See Section 9 - Physical and Chemical Properties. 6

SECTION 14 TRANSPORT INFORMATION Aerosols (limited quantity), Class 2.1, ERG 126 AIR (IATA) Aerosols (limited quantity), Class 2.1, ERG 126, UN No. 1950 Vessel Aerosol (Limited Quantity), Class 2.1, UN No 1950 SECTION 15 REGULATORY INFORMATION Environmental Regulations SARA 302/304: None SARA 311/312: Immediate ( x ) Delayed ( ) Fire ( x ) Reactive ( ) Sudden Release of Pressure ( x ) Section 313 None California Prop. 65: None This product meets the requirements as set forth by NSF International as a continuation of the USDA product approval program and based on the regulatory requirements of FDA 21 CFR for appropriate use, ingredient and labeling. All the chemicals used in this product are TSCA listed. Check with your local regulators to be sure all local regulations are met. SECTION 16 OTHER INFORMATION Hazard Ratings: This information is intended solely for the use of individuals trained in the NFPA and/or HMIS systems. NFPA: Level 3 Aerosol HMIS: Health: 1 Flammability: 4 Reactivity: 0 RATING: 4-EXTREME 3-HIGH 2-MODERATE 1-SLIGHT 0-INSIGNIFICANT 7

Note: For industrial use only. The information contained herein is accurate to the best of our knowledge. We do not suggest or guarantee that any hazards listed herein are the only ones which exist. We make no warranty of any kind, express or implied, concerning the safe use of this material in your process or in combination with other substances. Effects can be aggravated by other materials and/or this material may aggravate or add to the effects of other materials. This material may be released from gas, liquid, or solid materials made directly or indirectly from it. User has the sole responsibility to determine the suitability of the materials for any use and the manner of use contemplated. User must meet all applicable safety and health standards. Possession of an SDS does not indicate that the possessor of the SDS was a purchaser or user of the subject product. The information and recommendations contained herein are, to the best of Bettcher Industries and the manufacturer of this product, accurate and reliable as of the date issued. Bettcher and the manufacturer shall not be liable for any loss or damage arising out of the use thereof. The information and recommendations are offered for the user s consideration and examination, and it is the user s responsibility to satisfy itself that they are suitable and complete for its particular use. PLEASE NOTE: The above information is accurate to the best of our knowledge. However, since data, safety standards and government regulations are subject to change and the conditions of handling and use, or misuse are beyond our control, Bettcher MAKES NO WARRANTY, EITHER EXPRESS OR IMPLIED, WITH RESPECT TO THE COMPLETENESS OR CONTINUING ACCURACY OF THE INFORMATION CONTAINED HEREIN AND DISCLAIMS ALL LIABILITY FOR RELIANCE THEREON. User should satisfy himself that he has all current data relevant to his particular use. 8