Safety Data Sheet according to (EC) No 1907/2006 - ISO 11014-1 Page 1 of 1 Loctite Soft Plastic Adhesive SDS no. : 353348 Revision: 15.07.2009 printing date: 06.01.2010 1. Identification of the substance/preparation and of the company/undertaking Trade name: Loctite Soft Plastic Adhesive Intended use: Plastic adhesives Company name: Henkel Limited Technologies House Wood Lane End HP2 4RQ Hemel Hempstead Great Britain Phone: +44 (0)1442 278000 Fax-no.: +44 (0)1442 278071 E-mail address of person responsible for Safety Data Sheet: ua-productsafety.uk@uk.henkel.com Emergency information: 24 Hours Emergency Tel: +44 0 8701 906777 - For further general health & safety, technical and practical advice on this product, please call +44 (0) 1606 593933 or write to: Technical Services; Henkel Limited; Road 5; Winsford Industrial Estate; Winsford; Cheshire; CW7 3QY- Email: technical.services@henkel.co.uk 2. Hazards identification R11 Highly flammable. R19 May form explosive peroxides. R36/37 Irritating to eyes and respiratory system. F - Highly flammable Xi - Irritant The product is classified as hazardous within the meaning of the valid (EU) preparation directive. Solvents contained in the product evaporate during processing and their vapors can form explosive/highly inflammable air/vapor mixtures. Pregnant women should absolutely avoid breathe in and skin contact. General chemical description: Composition Base substances of preparation: Solvent 3. Composition / information on ingredients Declaration of ingredients according to (EC) No 1907/2006:
Hazardous components CAS-No. Tetrahydrofuran Loctite Soft Plastic Adhesive Page 2 of 2 EINECS ELINCS content Classification 203-726-8 70-90 % Xi - Irritant; R36/37 F - Highly flammable; R11, R19 For full text of the R-Phrases indicated by codes see section 16 'Other Information'. Substances without classification may have community workplace exposure limits available. Inhalation: Immediate medical treatment necessary. Move to fresh air. Skin contact: Rinse with running water and soap. Seek medical advice. 4. First aid measures Eye contact: Rinse immediately with plenty of running water (for 10 minutes). Seek medical attention if necessary. Ingestion: Rinse out mouth, drink 1-2 glasses of water, do not induce vomiting. Seek medical advice. Suitable extinguishing media: Carbon dioxide, foam, powder 5. Fire fighting measures Extinguishing media which must not be used for safety reasons: High pressure waterjet Special protection equipment for firefighters: Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear. In case of fire, keep containers cool with water spray. Personal precautions: Avoid skin and eye contact. Remove sources of ignition. 6. Accidental release measures Environmental precautions: Do not let product enter drains. Clean-up methods: For small spills wipe up with paper towel and place in container for disposal. For large spills absorb onto inert absorbent material and place in sealed container for disposal. Dispose of contaminated material as waste according to item 13.
Loctite Soft Plastic Adhesive Page 3 of 3 7. Handling and storage Handling: Use only in well-ventilated areas. Avoid skin and eye contact. Prolonged or repeated skin contact should be avoided to minimise any risk of sensitisation. Keep away from sources of ignition - no smoking. Open and handle container with care. Storage: Store in a cool, well-ventilated place. Keep away from sources of ignition. Do not store together with food or other consumables (coffee, tea, tobacco, etc.). 8. Exposure controls / personal protection Components with specific control parameters for workplace: Valid for Great Britain Basis UK EH40 WELs Ingredient ppm mg/m 3 Type Category Remarks Listed. EH40 WEL 100 300 Short Term Exposure ECTLV Limit (STEL): Skin designation: Can be absorbed through the ECTLV skin. 50 150 Time Weighted Average ECTLV (TWA). Skin designation: Can be absorbed through the EH40 WEL skin. 100 300 Short Term Exposure EH40 WEL Limit (STEL): 50 150 Time Weighted Average (TWA). EH40 WEL Engineering controls: Draw off vapors and fumes directly at the point of generation or release. In the case of regular work use bench-mounted extraction equipment. Respiratory protection: Suitable breathing mask when there is inadequate ventilation. Hand protection: In case of full contact protective gloves made from butyl rubber are recommended according to EN 374. material thickness > 0.7 mm Perforation time > 10 minutes In the case of longer and repeated contact please note that in practice the penetration times may be considerably shorter than those determined according to EN 374. The protective gloves must always be checked for their suitability for use at the specific workplace (e.g. mechanical and thermal stress, product compatibility, antistatic effects, etc.). The gloves must be replaced immediately at the first signs of wear and tear. The information provided by the manufacturers and given in the relevant trade association regulations for industrial safety must always be observed. We recommend that a hand care plan is drawn up in cooperation with a glove manufacturer and the trade association in accordance with the local operating conditions. Eye protection: Goggles which can be tightly sealed.
Loctite Soft Plastic Adhesive Page 4 of 4 Skin protection: suitable protective clothing General protection and hygiene measures: Wash hands before work breaks and after finishing work. Do not eat, drink or smoke while working. Good industrial hygiene practices should be observed. 9. Physical and chemical properties General characteristics: Appearance Odor: Liquid Clear Pungent Phys./chem. properties: Boiling point Flash point Density () Solubility (qualitative) (Solvent: Water) Solubility (qualitative) (Solvent: Acetone) Explosion limit lower [vol%] upper [vol%] 65 C (149 F) -17 C (1.4 F) 0,95 g/cm3 Insoluble Soluble 1,5 %(V) 12,4 %(V) Conditions to avoid: Heat, fumes, sparks and other sources of ignition. 10. Stability and reactivity 11. Toxicological information Oral toxicity: May cause irritation to the digestive tract. Inhalative toxicity: Irritating to respiratory system Skin irritation: Prolonged or repeated contact may cause skin irritation. Eye irritation: Irritating to eyes. 12. Ecological information Persistence and degradability: Ultimate biodegradation: The product contains polymere components that are degradable to a large extent. General ecological information: Do not empty into drains / surface water / ground water.
Loctite Soft Plastic Adhesive Page 5 of 5 13. Disposal considerations Product disposal: Dispose of in accordance with local and national regulations. Contribution of this product to waste is very insignificant in comparison to article in which it is used The valid EEC waste code numbers are not product-related but are largely source-related. The manufacturer is therefore unable to specify EEC waste codes for the articles or products used in the various sectors. These can be requested from the manufacturer. Disposal of uncleaned packages: After use, tubes, cartons and bottles containing residual product should be disposed of as chemically contaminated waste in an authorised legal land fill site or incinerated. Disposal must be made according to official regulations. Road transport ADR: 14. Transport information Classification code: F1 Hazard ident. number: 33 Technical name: Special provision 640D Railroad transport RID: Classification code: F1 Hazard ident. number: 33 Technical name: Special provision 640D Inland water transport ADN: Classification code: F1 Hazard ident. number: Technical name: Special provision 640D Marine transport IMDG: EmS: F-E,S-D Seawater pollutant: - Proper shipping name:
Loctite Soft Plastic Adhesive Page 6 of 6 Air transport IATA: Packaging instructions (passenger) 305 Packaging instructions (cargo) 307 Proper shipping name: Adhesives Indication of danger: 15. Regulations - classification and identification F - Highly flammable Xi - Irritant Risk phrases: R11 Highly flammable. R19 May form explosive peroxides. R36/37 Irritating to eyes and respiratory system. Safety phrases: S9 Keep container in a well-ventilated place. S16 Keep away from sources of ignition - No smoking. S23 Do not breathe vapour. S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S51 Use only in well-ventilated areas. S2 Keep out of the reach of children. S46 If swallowed, seek medical advice immediately and show this container or label. 16. Other information The labelling of the product is indicated in Section 15. The full text of the R-phrases indicted by codes in this safety data sheet are as follows: R11 Highly flammable. R19 May form explosive peroxides. R36/37 Irritating to eyes and respiratory system. Further information: This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is intended to describe our products from the point of view of safety requirements and is not intended to guarantee any particular properties.