Installation Instructions COLONY SOFT 7.0 Centerset Lavatory Faucet 7.0 with Speed Connect Drain Congratulations on purchasing your American Standard faucet with the Speed Connect drain, a features found only on American Standard faucets. H C Speed Connect Drain* / of the parts, installs in / of the time No tools needed Never needs adjustment Guaranteed to seal properly the first time, every time. Certified to comply with ANSI A.8. M968877 Rev.. *Your new American Standard faucet is designed to work only with the Speed Connect drain. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Recommended tools Screwdriver INSTALL FAUCET Channel Locks CAUTION Turn off water at main supply. Adjustable Wrench Plumbers' Putty or Caulking Tubing Cutter Apply a bead of putty along the edge of the underside of the FAUCET (). Insert FAUCET () and CABLE CONNECTOR () through center hole of mounting surface. From under side of mounting surface thread the two MOUNTING NUTS () onto FAUCET SHANKS (). Center FAUCET () and hand tighten MOUNTING NUTS () to secure FAUCET (). PUTTY (HAND TIGHTEN)
INSTALL POP-UP Remove CLEAR PLASTIC COVER (). Remove CARDBOARD SPACER () from under POP-UP (). Drop BODY () through sink drain hole. Make sure WHITE FOAM GASKET () is under flange of BODY (). 6 REAR OF SINK Note: No plumber s putty or caulk is required. The CABLE ATTACHMENT POINT (6) must face towards the rear of the SINK. SINK HOLE INSTALL BLACK GASKET Install BLACK CONE GASKET () onto BODY () from below. Note: The flat side of the BLACK CONE GASKET () must face down. FLAT SIDE OF GASKET MUST FACE DOWN INSTALL GRAY LOCKNUT Install GRAY LOCKNUT () onto BODY () from below SINK. Note: The flat side of the GRAY LOCKNUT () must face up. Tighten firmly by hand. No tools are required. Check FLANGE in SINK to ensure that WHITE FOAM GASKET () is fully compressed and not visible. FLAT SIDE OF GRAY LOCKNUT MUST FACE UP FLANGE WHITE FOAM GASKET NOT VISIBLE POP-UP KNOB POP-UP KNOB () must be fully down. DOWN M968877 Rev..
6 ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR () clockwise onto BODY CONNECTION () and hand tighten. Your new POP-UP installation is now complete. Note: Tailpeice on pop-up drain is -/ O.D. -/ O.D. 7 CHECK OPERATION OF POP-UP Operate LIFT KNOB () to verify that STOPPER () opens and closes. Note: If STOPPER () does not open and close properly then refer to the troubleshooting section of these instructions. 8 MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY. Connect water supply to INLET SHANKS () with /" IPS FLEXIBLE SUPPLIES () or /8" O.D. BULL-NOSE RISERS (). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length. Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS. Connect -/ O.D. TAILPIECE () on POP-UP to p trap. COUPLING NUT ON FLEX SUPPLIES /8 O.D. BULL-NOSE RISERS COUPLING NUT WITH FAUCET FLEXIBLE SUPPLIES COMPRESSION NUT FERRULE P TRAP HOT /8 COMPRESSION CONNECTION COLD M968877 Rev..
9 TEST INSTALLED FITTING With HANDLES () in OFF position, turn on WATER SUPPLIES () and check all connections for leaks. Ensure that AERATOR () is tightened completely. Operate HANDLES () to allow water flow. 0 CHECK CONNECTIONS Operate POP-UP KNOB () and fill Sink with water. Check that STOPPER () makes a good seal and retains water in Sink. If STOPPER () does not seal properly, please refer to Troubleshooting Guide in these instructions. Release POP-UP KNOB () down and check all drain connections and "P" trap for leaks. Tighten if necessary. WASTE OUTLET P TRAP SERVICE If Faucet Drips Proceed As Follows: Turn VALVE in OFF position. If spout drips, operate HANDLES () several times from OFF to ON position. Do not force-handles turn only 90. To change direction of handle rotation, proceed as follows: Turn VALVE to OFF position. Loosen HANDLE SCREW (), and pull HANDLE () off ADAPTOR (). Remove ADAPTOR SCREW (). Pull ADAPTOR () off VALVE STEM () and turn 90 in a way that flat in ADAPTOR () catches a different flat in on VALVE STEM (). Reinstall ADAPTER SCREW (), HANDLE () and HANDLE SCREW (). AERATOR (6) may accumulate dirt causing distorted and reduced water flow. Remove AERATOR (6) and rinse clean. CARE INSTRUCTIONS: FLAT 6 DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. M968877 Rev..
Speed Connect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position: Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode. CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector () counter-clockwise. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration. Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the Stopper should be in the UP position. Fig. B, C. Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C. Re-attach the Cable to the Drain Body Connection () by threading the Cable Connector () clockwise onto the Drain Body Connection () and hand-tighten. RE-ATTACH CAM Fig. C. DISCONNECT CAM CAP STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector () counter-clockwise. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration. Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D. Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E. The Stopper can now be removed by lifting it out of the Drain. Fig. F. Fig. D. Fig. E. Fig. F. REMOVE CAM REMOVE CAM CAP M968877 Rev..
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, Locked Mode (Stopper cannot be removed) or Unlock Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. Fig. G. To install the stopper in Locked mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.fig. G. LOGO Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J. Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not snap into place, then rotate the Cam to make sure it is fully inserted. Fig. K. Re-attach Cable. See CABLE ADJUSTMENT PROCEDURE in Troubling Shooting Guide to complete installation. Stopper will be in Locked mode and not be removable. LOOP TOWARD REAR OF SINK locked Mode Unlocked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. H. To install the stopper in Unlocked mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down. Fig. H. Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J. Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not snap into place, then rotate the Cam to make sure it is fully inserted. Fig. K. Re-attach Cable. See CABLE ADJUSTMENT PROCEDURE in Troublingshooting Guide to complete installation. Stopper will be in Unlocked mode and removable. LOGO 80 LOOP TOWARD FRONT OF SINK Unlocked Mode Fig. H. INSTALL CAM Fig. J. Fig. K. CAM INSTALL CAM CAP 6 M968877 Rev..
M980-0070A SCREW M908-0070A ACRYLIC HANDLE H M90-0070A INDEX, BUTTON, HOT M90-0070A INDEX, BUTTON, COLD COLONY SOFT CENTERSET FAUCET MODEL NUMBER 7.0 7.0 M9807-0070A HANDLE SCREW M9680-YYY0A METAL LEVER HANDLE Replace the "YYY" with appropriate finish code CHROME 00 BRASS 099 M980-0070A SCREW M980-0070A ADAPTER M90900-0070A VALVE NUT M90760-YYY0A PLUG BUTTON M907-YYY0A POP-UP ROD M9806-0070A BEARING WASHER A90-0070A VALVE 077-YYY0A AERATOR M90-0070A CABLE ASSEMBLY 06800-0070A ATTACHMENT NUT M96-YYY0A STOPPER ASSEMBLY 00-0070A SUPPLY NUT M908-007A SPONGE WASHER M90-YYY0A ASSEMBLY M960-0070A CAM ASSEMBLY HOT LINE FOR HELP For toll-free information and answers to your questions, call: -800--90 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA -800-87-069 (TORONTO -90-06-09) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 0-800-89--00 Product names listed herein are trademarks of American Standard Inc. AS America, Inc. 008 7 M96-0070A MOUNTING KIT M968877 Rev..