1 MATERIAL SAFETY DATA SHEET I. IDENTIFICATION Manufacturer: Siovation, LLC Address: 1025 Progress Circle, Lawrenceville, GA 30043 Telephone Number: (770) 339-4460 Or (800) 822-4460 Fax Number: (770) 339-4464 Product Name: T-Sil 100 Chemical Name: Polydimethylsiloxane C.A.S. Number: 63148-62-9 Effective Date: July 22, 1990 Revision Date: March 2, 2009 II. COMPOSITION/INFORMATION ON INGREDIENTS All components in this product are listed in the T.S.C.A. Inventory. Product Composition/ C.A.S. Registration Number Approximate Weight Percentage Exposure Limits Comments: Any components listed above are hazardous as defined in 29 CFR 1910.1200 or as an informational aid. III. HAZARDS IDENTIFICATION Acute Effects Eyes: Skin: Inhalation: Ingestion: Comment{s}: May cause slight irritation to the eyes and prolonged exposure may result in damage to the Cornea. Single exposure causes no known effect. Prolonged contact may cause moderate irritation. Repeated skin contact may cause dermatitis. irritation to nose or throat expected from relatively short exposure. Prolonged or repeated exposure may irritate the upper respiratory tract. Amounts transferred to the mouth by fingers, etc., during normal operations should not cause injury. known, adverse chronic health effects, but unnecessary exposure to any chemical should be avoided. This product, as with any chemical, may enhance allergic conditions on certain people. There are no known, medical conditions that might be aggravated by exposure to this product.
2 III. HAZARDS IDENTIFICATION {Continued} Special Hazards Carcinogens: Mutagens: Reproductive Toxins: Sensitizers: known. known. known. known. IV. FIRST AID MEASURES Eyes: Skin: Inhalation: Ingestion: Comment{s}: NOTES TO PHYSICIAN: Immediately upon exposure to the eyes, they should be flushed with plenty of fresh water, ensuring that under both the upper and lower lids are rinsed well for five to ten minutes. GET MEDICAL ATTENTION if irritation persists. Exposed skin should be thoroughly rinsed with fresh water to move the product from the exposed area as soon as possible. If irritation persists, CONSULT A PHYSICIAN. Move affected person into fresh air. Keep person calm and under observation. If breathing difficulties or irritation persists, CONSULT A PHYSICIAN. Data regarding the effects of ingestion is not available. If product is ingested, CONSULT A PHYSICIAN. Keep person under observation. Never give anything by mouth to an unconscious person. Although this product is considered to be a safe product, the user assumes the liability to ensure that safe and prudent procedures are used in handling and using the product in order to ensure that personnel are not dangerously exposing the eyes and skin without proper safeguards. All treatments should be based on observed signs and symptoms of distress in the patient. Consideration should be given to the possibility of overexposure to materials other than this product. Treat symptomatically. specific antidote available. V. FIRE AND EXPLOSION HAZARD Flash Point: {Method}: Auto Ignition Temperature: Flammability Limits In Air: Extinguishing Media: Hazardous Decomposition Products: Above 200 o F Open Cup t determined. t determined. All standard firefighting media. This product contains polydimethylsiloxane which can generate formaldehyde at approximately 300 F (150 C) and above in atmospheres containing oxygen. Other decomposition products are carbon oxides and silica (crystalline).
3 VI. ACCIDENTAL RELEASE MEASURES Containment / Clean-Up: Keep unnecessary personnel away from site of spill. If safe to do so, shut off release. Caution: Floor may be slippery; use care to avoid falling. Contain spills immediately with inert materials (e.g. sand, earth). Transfer liquids and solid material used to create dikes, into suitable containers for recovery or disposal. Collected product, residues, and clean-up materials may be governmentally regulated; see Section XIII for Disposal Consideration. CAUTION: Keep spills and all cleaning runoff efforts out of municipal sewers and open bodies of water. Clean any remaining slippery surfaces by appropriate techniques, such as: Mopping or high-pressure steam for large areas, etcetera. Observe all personal protection equipment recommendations described in Section VIII. Local, state, and federal reporting requirements may apply to spills or releases of this material into the environment. See applicable regulatory compliance information in Section XV. te: See Section 8 for Personal Protection Equipment for Spills. VII. HANDLING AND STORAGE Handling: Storage: Keep container closed when not in use. Avoid direct or prolonged contact with skin and eyes. Avoid breathing vapors and mists. Store in tightly closed containers. Store in a dry, well-ventilated area, away from incompatible materials, see Section X. Protect container from damage and extremes of heat. VIII. EXPOSURE CONTROLS/PERSONAL PROTECTION Engineering Controls: Personal Protective Equipment For Routine Handling: Personal Protective Equipment For Spills: Local Exhaust: Should be unneeded. If dust or mist is generated by the process, use local exhaust ventilation with a minimum capture velocity of 150 ft/min. (0.75 m/sec.) at the point of evolution. General Ventilation: Recommended. Eyes: Use proper protection, safety glasses with side shields as a minimum, or preferably chemical splash goggles (ANSI Z87.1 or approved equivalent). Skin: Wear chemically resistant gloves along with long-sleeved, body-covering clothing Suitable Gloves: Nitrile / Neoprene gloves may provide best protection against permeation Inhalation: Respiratory protection should be unneeded. A respiratory protection program meeting OSHA 1910.134 requirements are to be followed whenever workplace conditions warrant respirator use. Suitable Respirator: If irritation is experienced, NIOSH approved respirator is recommended. Eyes: Use proper protection, safety glasses with side shields as a minimum or preferably chemical splash goggles (ANSI Z87.1 or approved equivalent). Skin: Wear chemically resistant gloves along with long-sleeved, body-covering clothing. Nitrile or Neoprene gloves may provide best protection against permeation. Inhalation/Suitable Respirator: If irritation is experienced, NIOSH approved respirator is recommended. A respiratory protection program meeting OSHA 1910.134 requirements are to be followed whenever workplace conditions warrant respirator use. Precautionary Measures: Facility is to be equipped with eyewash and safety showers close to point of product usage. Avoid eye contact. Avoid skin contact. Use reasonable care. Comments: These precautions are for room temperature handling. Use at elevated temperatures, or in aerosol/spray applications, may require added precautions.
4 IX. PHYSICAL AND CHEMICAL PROPERTIES Physical Appearance: Color: Odor: Clear Liquid Colorless Mild Odor Specific Gravity @ 25 C: 0.97 Solubility In Water: Viscosity: ph: Insoluble 100 Centistokes t Applicable te: The above information is not intended for use in preparing product specifications. Contact manufacturer before writing specifications. X. STABILITY AND REACTIVITY Chemical Stability: Hazardous Polymerization: Conditions To Avoid: Materials To Avoid: Comments: Stable. Thermal decomposition is dependent on time and temperature. Hazardous polymerization will not occur. known. Oxidizing material can cause a reaction.. XI. TOXICOLOGICAL INFORMATION Product does not contain any substances at levels considered by OSHA, NTP, IARC or ACGIH to be human carcinogens. Complete information is not yet available. XII. ECOLOGICAL INFORMATION Complete information is not yet available. XIII. DISPOSAL CONSIDERATIONS Disposal Method: Recovery and reuse, rather than disposal, should be the ultimate goal of handling efforts. The material resulting from clean-up operations may be a hazardous waste and therefore, subject to specific regulations. Chemical additions, processing or other alterations of this material may make the waste management information presented in this MSDS incomplete, inaccurate or otherwise inappropriate. This product, due to these alterations, may be classified as a RCRA Hazardous waste in accordance with 40 CFR 261. According to RCRA, it is the responsibility of the waste generator to ensure proper disposal. Be advised that state and local requirements for waste disposal may be more restrictive or otherwise different from federal laws and regulations. Consult state and local regulations regarding the proper disposal of this material.
5 XIV. TRANSPORTATION INFORMATION Proper Shipping Name (49 CFR 172.101): D.O.T. Identification Number (49 CFR 172.101): D.O.T. Hazard Class (49 CFR 172.101): R.C.R.A. Hazard Class (40 CFR 261) [If Discarded]: E.P.A. Priority Pollutants (40 CFR 122.53): t Listed () XV. REGULATORY INFORMATION O.S.H.A. Status: T.S.C.A. Status: D.S.L. (Canada): Contents of this MSDS comply with the O.S.H.A. Hazard Communication Standard 29 CFR 1910.1200. All chemical substances found in this product comply with the Toxic Substances Control Act inventory reporting requirements. All chemical substances found in this product are listed. W.H.M.I.S. Classification: E.P.A. SARA Title III Chemical Listing: t-controlled Section 302 Extremely Hazardous Substances: Section 304 C.E.R.C.L.A. Hazardous Substances: RQ () Section 312 Hazard Class: Acute: Chronic: Fire: Pressure: Reactive: Section 313 Toxic Chemicals: present or none present in regulated quantities. Hazard Ratings Health Fire Reactivity Special HMIS: 0 1 0 X NFPA: 0 1 0 X The information and recommendations set forth in this Material Safety Data Sheets relate only to the Siovation products referenced herein (the Products ) and are offered in good faith and believed by Siovation, LLC to be correct. This document is only intended as a guide to the precautionary handling of the Products by an appropriately-trained person. Each user of the Products should review this information and these recommendations to determine their relevance and applicability in the specific context in which the Products are to be used. SIOVATION, LLC MAKES NO (A) REPRESENTATIONS AS TO THE ACCURACY AND COMPLETENESS OF SUCH INFORMATION AND RECOMMENDATIONS, OR (B) REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED, OF MECHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR OF ANY OTHER NATURE WITH RESPECT TO THE INFORMATION AND RECOMMENDATIONS OR WITH RESPECT TO THE PRODUCT TO WHICH THE INFORMATION REFERS. Prepared by: Siovation (rmb)