Material Safety Data Sheet SuperStretch Silicone Molding Rubber Supplier: Gesswein Co., Inc. Address: 201 Hancock Ave., Bridgeport CT 06605 Telephone: 203-366-5400 Fax: 203-366-3953 Date Prepared: May 20, 2012 Emergency: ChemTel: 1-800-255-3924 Telephone: Date Prepared by: Michael Knight SECTION 1: Identity CAS NO.: Chemical Name : Chemical Family: Formula: Mixture VMQ Rubber Compound (Mixture) SECTION 2 - Hazardous Ingredients Principal Hazardous component(s) (chemical & common name(s)) % Threshold Limit Value (units). This mixture has not been evaluated as a whole. All ingredients are bound in a polymer matrix and potential for hazardous exposure as shipped is minimal. However, some fumes may be released upon heating or vulcanization and the end-user (fabricator) must take the necessary precautions (mechanical ventilation, respirator program, etc.) to protect his employees from exposure. (See Section 7 - Special Precautions). The following ingredients are considered hazardous per OSHA 1910.1200. MSDS for each is attached: 4570930 VAROX DBPH IRRITANT NOTE: If chemical is not specifically identified, it is considered proprietary. SECTION 3: Physical and Chemical Characteristics (Fire and Explosion Data) Boiling Point: Vapor Density ( Air = 1 ): Evaporation Rate ( = 1 ): Solid Solid Specific Gravity ( H 2 O = 1 ): 1.07
Water Reactive: Flammable Limits in Air % by Volume: Vapor Pressure (mm Hg): Melting Point: Solubility In Water: Appearance and Odor: Odor Flash Point: Extinguisher Media: Auto-Ignition Temperature: Insoluble Solid: Mild Unknown All common Unknown Special Fire Fighting Procedures: Self-contained breathing apparatus should be worn to prevent inhalation of smoke and decomposition products. SECTION 4: Physical Hazards Stability: CONDITIONS TO AVOID Incompatibility (Materials to Avoid): Hazardous Decomposition Products: Hazardous Polymerization: Stable ne Known Oxides of C, S:O2 Will t Occur SECTION 5 - Health Hazard Data (See Section 2) Threshold Limit Value: t Established Signs and symptoms of Exposure: 1. Acute Overexposure: ne Known 2. Chronic Overexposure: ne Known Medical Conditions Generally Aggravated by Exposure: ne Known CHEMICAL LISTED AS CARCINOGEN OR POTENTIAL CARCINOGEN National Toxicology Program: I.A.R.C. Monographs: OSHA: OSHA Permissible Exposure Limit: ACGIH Threshold limit Value: Other Exposure Limit Used: EMERGENCY FIRST AID PROCEDURES Eye Contact: Skin Contact: Inhalation: Ingestion: Consult physician if irritation occurs. Physical form should preclude any harmful effect from contact. Consult physician if respiratory irritation occurs. Consult physician
SECTION 6 - Special Protection Information Respiratory Protection (Specify Type): Ventilation: Protective Gloves: Eye Protection: Other Protective Clothing or Equipment: May be necessary if mechanical ventilation is insufficient. Local Exhaust: Yes Mechanical (General): Yes Yes ne SECTION 7 - Special Precautions and Spill / Leak Procedures Precautions to be Taken in Handling and Storage: Steps to be Taken in Case Material is Released or Spilled: Waste Disposal Methods: CAUTION: Nitrosamines - considered to be possible human carcinogens - may be formed during processing of rubber com pounds. Mixing or contacting this products with nitrates or nitrites, as in salt bath curing, may produce hazardous levels of volatile nitrosamines. Avoid inhaling fumes from hot rubber processing - especially vulcanization. Scoop or shovel material and return to original container. See Section Eight for applicable State and Federal regulations. Dispose of in accordance with all local, state and federal regulations. SECTION 8 - Regulatory Information The following ingredients of this mixture are reportable as listed under Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1988 (SARA) and 40 CFR Part 372: Component CAS NO. % ne The user must determine whether a report is required to EPA for any amount of this NOTICE: HEALTH HAZARD INFORMATION MATERIAL #4571930: material disposed of or otherwise released into the environment. This notification must remain attached to its accompanying MSDS. If the MSDS is copied or redistributed, a copy of this notification must also be attached. This material is an organic peroxide with potential for eye, skin or respiratory irritation on exposure to vulcanization fumes. Minimize breathing of fumes through adequate ventilation and or organic vapor respirator. As with all rubber compounds, minimize employee exposure through the use of gloves and adequate ventilation. SECTION 9 - Physical and chemical properties APPEARANCE Physical state / form: Colour: Odour: Gum SAFETY PARAMETERS METHOD Tan and other colors. Characteristic Melting point /melting range: Boiling point / boiling range: Flash point: Ignition temperature: Lower explosion limit (LEL): Upper explosion limit (UEL):
Vapour pressure: Density: Water solubility / miscibility: Insoluble ph-value: Viscosity (dynamic): Approx. 1.0-1.5 g/cm³ (Estimated Value) SECTION 10 - Stability and reactivity General information: Conditions to avoid: Materials to avoid: Hazardous decomposition products: Further information: If stored and handled in accordance with standard industrial practices no hazardous reactions are known. If stored and handled in accordance with standard industrial practices and local regulations where applicable: none known. Measurements have shown the formation of small amounts of formaldehyde at temperatures above about 150 C (302 F) through oxidation. Hazardous polymerization cannot occur. SECTION 11 - Toxicological information General information: SECTION 12 - Ecological information Information on elimination (persistence and degradability) Behavior in environmental compartments Ecotoxicological effects: Additional information - General information: Toxicological testing has not been conducted with this material. SECTION 13 - Disposal considerations Product disposal Recommendation: Packaging disposal Recommendation SECTION 14 - Transport information ecological data exists for this material. environmental problems expected if handled and treated in accordance with standard industrial practices and local regulations where applicable. Easily separable from water by filtration. Material that cannot be used or chemically reprocessed should be disposed of at an approved facility in accordance with any applicable governmental regulations. Containers should be completely emptied before recycling as specified in government regulations. Empty containers should be sent to an approved recycling facility. US DOT & CANADA TDG SURFACE: Valuation...: t regulated for transport Transport by sea IMDG- Code: Valuation...: t regulated for transport Air transport ICAO-TI / IATA- DGR: SECTION 15 - Regulatory information U.S. FEDERAL REGULATIONS TSCA inventory status and TSCA information: CERCLA Regulated Chemicals: Valuation...: t regulated for transport This material or its components are listed on or are in compliance with the requirements Substance Inventory..
SARA 311/312 Hazard Class: This product does not present any SARA 311/312 hazards. HAPS (Hazardous Air Pollutants): This material has not been evaluated for the presence of chemicals on the Hazardous Air Pollutants (HAPS) list. U.S. State regulations: The status of this material with regard to State Listings has not been determined. California Proposition 65 Carcinogens: California Proposition 65 Reproductive Toxins: Canadian regulations: DSL Status: SECTION 16 - Other information Additional information: Glossary of Terms: This material has not been evaluated for the presence of California Proposition 65 Reproductive Toxins. This material has not been evaluated for the presence of California Proposition 65 Reproductive Toxins. This product has been classified in accordance with the Hazard criteria of the CPR and the MSDS contains all the information required by the CPR. The Canadian DSL status of this material has not been determined. This Material Safety Data Sheet (MSDS) meets the requirements of the Federal OSHA Hazard Communication Standard (29 CFR 1910.1200). This product has been classified according to the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all of the information required by the CPR. This information relates to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. Such information is to the best of our knowledge and belief accurate and reliable as of the date compiled. However, no representation, warranty or guarantee expressed or implied, is made as to its accuracy, reliability or completeness. It is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use. We do not accept liability for any loss or damage that may occur from the use of this information. thing herein shall be construed as a recommendation for uses which infringe valid patents or as extending a license under valid patents. This MSDS provides selected regulatory information on this product, including its components. This is not intended to include all regulations. It is the responsibility of the user to know and comply with all applicable rules, regulations and laws relating to the product being used. ACGIH - American Conference of Governmental Industrial Hygienists DOT - Department of Transportation hpa - Hectopascals mpa*s - Milli Pascal-Seconds OSHA - Occupational Safety and Health Administration PEL - Permissible Exposure Limit ppm - Parts per Million SARA - Superfund Amendments and Reauthorization Act STEL - Short Term Exposure Limit TSCA - Toxic Substances Control Act TWA - Time Weighted Average WHMIS - Canadian Workplace Hazardous Materials Identification System Flash point determination methods Common name ASTM D56 Tagliabue (Tag) closed cup ASTM D92, DIN 51376, ISO 2592 Cleveland open cup ASTM D93, DIN 51758, ISO 2719 Pensky-Martens closed cup ASTM D3278, DIN 55680, ISO 3679 Setaflash or Rapid closed cup DIN 517 Abel-Pensky closed cup