ANNUAL OF NAVIGATION 6/2003

Similar documents
An Aerodynamic Analysis of Current Data for USS Akron Airship

STABILITY OF MULTIHULLS Author: Jean Sans

1. A tendency to roll or heel when turning (a known and typically constant disturbance) 2. Motion induced by surface waves of certain frequencies.

The risk assessment of ships manoeuvring on the waterways based on generalised simulation data

Aerodynamic Analyses of Horizontal Axis Wind Turbine By Different Blade Airfoil Using Computer Program

An Investigation into the Capsizing Accident of a Pusher Tug Boat

Bayesian methods in reliability of search and rescue action

J. Szantyr Lecture No. 21 Aerodynamics of the lifting foils Lifting foils are important parts of many products of contemporary technology.

C-1: Aerodynamics of Airfoils 1 C-2: Aerodynamics of Airfoils 2 C-3: Panel Methods C-4: Thin Airfoil Theory

The Study on the Influence of Gust Wind on Vehicle Stability Chen Wang a, Haibo Huang b*, Shaofang Xu c

SUBPART C - STRUCTURE

Preliminary Design Review (PDR) Aerodynamics #2 AAE-451 Aircraft Design

JAR-23 Normal, Utility, Aerobatic, and Commuter Category Aeroplanes \ Issued 11 March 1994 \ Section 1- Requirements \ Subpart C - Structure \ General

PRESSURE DISTRIBUTION OF SMALL WIND TURBINE BLADE WITH WINGLETS ON ROTATING CONDITION USING WIND TUNNEL

An Analysis of Lift and Drag Forces of NACA Airfoils Using Python

Aerodynamics Loads on a Heeled Ship

Georgian University GEOMEDI. Abstract. In this article we perform theoretical analysis of long jumps with the purpose to find

Abstract. 1 Introduction

A Feasibility Study on a New Trimaran PCC in Medium Speed

Wind loads investigations of HAWT with wind tunnel tests and site measurements

A methodology for evaluating the controllability of a ship navigating in a restricted channel

ScienceDirect. Relating baseball seam height to carry distance

RESOURCE DECREASE BY LARGE SCALE WIND FARMING

Aerodynamic Analysis of a Symmetric Aerofoil

Pressure distribution of rotating small wind turbine blades with winglet using wind tunnel

Windmills using aerodynamic drag as propelling force; a hopeless concept. ing. A. Kragten. April 2009 KD 416

Approximate Method of Calculating Forces on Rudder During Ship Sailing on a Shipping Route

RESEARCH MEMORANDUM. WASHINGTON December 3, AERODYNl$MIC CHARACTERISTICS OF A MODEL? OF AN ESCAPE ...,

STUDIES ON THE OPTIMUM PERFORMANCE OF TAPERED VORTEX FLAPS

EXPERIMENTAL RESEARCH ON THE MECHANICAL SOLICITATIONS OF THE GREENHOUSES OF VEGETABLES AND FLOWERS LOCATED ON ROOFTOPS

Dynamic Component of Ship s Heeling Moment due to Sloshing vs. IMO IS-Code Recommendations

Pressure coefficient on flat roofs of rectangular buildings

Research of Sail Height Adjustment on Sail-Assisted Ship in Different Loading and Wind Conditions

Available online at ScienceDirect. Procedia Engineering 161 (2016 )

EVALUATING CRITERIA FOR DP VESSELS

Aerodynamic Terms. Angle of attack is the angle between the relative wind and the wing chord line. [Figure 2-2] Leading edge. Upper camber.

Yasuyuki Hirose 1. Abstract

Determination of the wind pressure distribution on the facade of the triangularly shaped high-rise building structure

Low Speed Wind Tunnel Wing Performance

D DAVID PUBLISHING. Aerodynamics Loads on a Heeled Ship. 1. Introduction. Romain Luquet 1, Pierre Vonier 1, Jean-Francois Leguen 1 and Andrew Prior 2

External Tank- Drag Reduction Methods and Flow Analysis

Ship Stability. Ch. 8 Curves of Stability and Stability Criteria. Spring Myung-Il Roh

Critical Gust Pressures on Tall Building Frames-Review of Codal Provisions

IMO REVISION OF THE INTACT STABILITY CODE. Proposal of methodology of direct assessment for stability under dead ship condition. Submitted by Japan

Computer Simulation of a Train Exiting a Tunnel through a Varying Crosswind

Principles of Sailing

ValidatingWindProfileEquationsduringTropicalStormDebbyin2012

Welcome to Aerospace Engineering

machine design, Vol.6(2014) No.3, ISSN pp

Evaluation of aerodynamic criteria in the design of a small wind turbine with the lifting line model

Experimental Investigation Of Flow Past A Rough Surfaced Cylinder

INCLINOMETER DEVICE FOR SHIP STABILITY EVALUATION

COMPARATIVE ANALYSIS OF THE FLOODING TIME MAIN ENGINE SHIP TYPE 888 DEFINED FROM CALCULATIONS AND MODEL RESEARCH

AERODYNAMIC CHARACTERISTICS OF SPIN PHENOMENON FOR DELTA WING

Numerical and Experimental Investigations of Lift and Drag Performances of NACA 0015 Wind Turbine Airfoil

AN INVESTIGATION INTO THE INFLUENCE OF TANK FILLING LEVEL ON LIQUID SLOSHING EFFECTS ONBOARD SHIPS - STATIC AND DYNAMIC APPROACH

Aerodynamics of Winglet: A Computational Fluid Dynamics Study Using Fluent

Investigation on 3-D Wing of commercial Aeroplane with Aerofoil NACA 2415 Using CFD Fluent

Abstract. 1 Introduction

EXPERIMENTAL RESEARCH ON DETERMINATION OF DRAG COEFFICIENT OF THE GREENHOUSES LOCATED ON ROOFS OF BUILDINGS

CFD Analysis ofwind Turbine Airfoil at Various Angles of Attack

Chapter 5 Wing design - selection of wing parameters - 4 Lecture 22 Topics

The Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration. M. Burak Şamşul

COMPUTER-AIDED DESIGN AND PERFORMANCE ANALYSIS OF HAWT BLADES

Experimental Study on the Large Roll Motion of a ROPAX Ship in the Following and Quartering Waves

The effect of back spin on a table tennis ball moving in a viscous fluid.

Incompressible Flow over Airfoils

PHYSICAL AND NUMERICAL MODELLING OF WAVE FIELD IN FRONT OF THE CONTAINER TERMINAL PEAR - PORT OF RIJEKA (ADRIATIC SEA)

CERTIFICATES OF COMPETENCY IN THE MERCHANT NAVY MARINE ENGINEER OFFICER

Drag Divergence and Wave Shock. A Path to Supersonic Flight Barriers

Testing of a oil spill mathematical model contained in PISCES II simulator

3D CDF MODELING OF SHIP S HEELING MOMENT DUE TO LIQUID SLOSHING IN TANKS A CASE STUDY

Aerodynamic Design, Fabrication and Testing of Wind Turbine Rotor Blades

Numerical analysis of influence of streamline rudder on screw propeller efficiency

A Different Approach to Teaching Engine-Out Glides

Prognosis of Rudder Cavitation Risk in Ship Operation

Research on Goods and the Ship Interaction Based on ADAMS

COURSE NUMBER: ME 321 Fluid Mechanics I Fluid statics. Course teacher Dr. M. Mahbubur Razzaque Professor Department of Mechanical Engineering BUET

Aerodynamic Performance of Trains with Different Longitudinal Section Lines under Crosswind

FLUID MECHANICS Time: 1 hour (ECE-301) Max. Marks :30

RESEARCH ON THE WIND LOAD PARAMETERS AND THE WIND FENCES BEHAVIOR FOR WIND FENCES OF RAILWAY BRIDGE

A Study on Roll Damping of Bilge Keels for New Non-Ballast Ship with Rounder Cross Section

The below identified patent application is available for licensing. Requests for information should be addressed to:

Effects of wind incidence angle on wind pressure distribution on square plan tall buildings

Smoke and heat Ventilator Testing

Analysis of dilatometer test in calibration chamber

THEORY OF WINGS AND WIND TUNNEL TESTING OF A NACA 2415 AIRFOIL. By Mehrdad Ghods

CFD ANALYSIS OF AIRFOIL SECTIONS

Velocity spectrum and blade s deformation of horizontal axis wind turbines

EXPERIMENTAL WIND TUNNEL TESTS ON LARGE PASSENGER SHIPS

WIND-INDUCED LOADS OVER DOUBLE CANTILEVER BRIDGES UNDER CONSTRUCTION

Stability and Computational Flow Analysis on Boat Hull

Aerofoil Profile Analysis and Design Optimisation

The wind tunnel tests of wind pressure acting on the derrick of deepwater semi-submersible drilling platform

EXPERIMENTAL STUDY OF WIND PRESSURES ON IRREGULAR- PLAN SHAPE BUILDINGS

Comparative Stability Analysis of a Frigate According to the Different Navy Rules in Waves

Measurement of Pressure. The aerofoil shape used in wing is to. Distribution and Lift for an Aerofoil. generate lift due to the difference

Center Distance Change of Silent Chain Drive Effect on Sprocket Tooth Profile Modification Wei Sun 1,a, Xiaolun Liu 1,b, Jiajun Liu 1 and Wei Zhang 1

A NOVEL FLOATING OFFSHORE WIND TURBINE CONCEPT: NEW DEVELOPMENTS

V393.R46. NalupwL UNITED STATES EXPERIMENTAL MODEL BASIN NAVY YARD, WASHINGTON, D.C. BILGE KEEL CAVITATION J. G. THEWS SEPTEMBER REPORT NO.

Transcription:

ANNUAL OF NAVIGATION 6/23 Leszek Smolarek Gdynia Maritime University Faculty of Navigation MODELING OF THE WIND GENERATED FORCE ACTING ON THE LIFERAFT ABSTRACT The aim of this paper is to derive a mathematical model for estimating the wind forces and wind moments effects a life raft. The mathematical model based on data from laboratory experiments. Forces due to the action of wind are adequately described. The governing physical equations, however, contain characteristics of the environment that are often not well quantified. In the strong wind condition, when the wind speed is much larger than the current and body speeds, all wind-generated forces must be taken into account. Friction and pressure forces exerted by the wind on the upper part of the floating body result in the wind force, which has a downwind component (drag) and a crosswind component (side force or lift), [][2]. The drag component is always positive. The side force or lift component can be positive or negative[8]. The lift depends on the wind speed, body geometry, and strongly on the angle between the long axis of the floating body and the wind direction. In this paper the author presents models of wind forces acting at a life raft. Data from laboratory experiments (wind tunnel [5]) are used to build dynamical models. INTRODUCTION The stability of the liferaft shall be considered in the hull-borne, transitional and foil-borne modes. The stability investigation shall also take into account the effects of external forces. The following procedures are outlined for guidance in dealing with stability: relationship between the capsizing moment and heeling moment to satisfy the weather criterion heeling moment due to wind pressure. 8

Leszek Smolarek The heeling moment M V shall be taken as constant during the whole range of heel angles and calculated by the following expression [2]: M V =. P V A V Z (knm) where: P V - wind pressure (N/m 2 ), A V - windage area including the projections of the lateral surfaces of the raft, superstructure and various structures above the waterline (m 2 ) Z - windage area lever (m) that is the vertical distance to the geometrical centre of the windage area from the waterline LABORATORY EXPERIMENTS IN THE AERODYNAMIC TUNNEL The aim of experiments was to determine the wind forces acting at a liferaft. Aerodynamic experiments of inflatable life rafts were performed in the Laboratory of Low Velocities in the Institute of Aviation [5]. Fig.. A ten- person raft in the aerodynamic tunnel The research was carried out in the aerodynamic tunnel. The research concerned the range of speeds in the measurement space of the tunnel from 2 to 64 knots, V w = -34 m/s. 82 Annual of Navigation

MODELING OF THE WIND GENERATED FORCE ACTING ON THE LIFERAFT The speed profile was transformed according to the formula [5]: where: Vw V ref Z Z ref κ =, V w = Vref Z Z ref κ wind speed on the height of raft measured from the sea surface (m/s) reference speed- speed of undisturbed flow (m/s) the raft height measured from the water (m) surface,5 m the reference height that is the height at which in the aerodynamic tunnel conditions, the flow speed equals an undisturbed flow speed for the sea according to ISO standard. To estimate a real wind pressure force F N, for a certain wind speed a dynamic pressure q was modelled [5]: ρ q = ( ) V 2 w 2 In standard conditions: surrounding temperature T = 5 o C, atmosphere pressure 3.2 hp, air density ρ =.233 kg/m 3. A wind pressure force F N in real conditions is equal to [5]: F N = x q ( ) ρ V 2 w 2 where x /q - reduced pressure force number in the stream system (modelled during the research) Forces and moments presented in the fig.2 were measured in the laboratory. Measurements were performed in two coordinate systems: wind direction system, XOY, with X - axis (OX) parallel to the wind speed vector; liferaft main axis system, X OY. 6/23 83

Leszek Smolarek Fig. 2. Measured forces and moments where: β angel between wind direction (axis Ox) and direction of axis Ox [deg]; X - drag force in wind direction system [N]; Y - side force in wind direction system [N]; Z - lift force in wind direction system [N]; MX - rolling moment in wind direction system [Nm]; MY - pitching moment in wind direction system [Nm]; MZ - yawing moment in wind direction system [Nm]; X - drag force in liferaft main axis system [N]; Y - side force in liferaft main axis system [N]; Z - side force in liferaft main axis system [N]; MX - rolling moment in liferaft main axis system [Nm]; MY - pitching moment in liferaft main axis system [Nm]; MZ - yawing moment in liferaft main axis system [Nm]. 84 Annual of Navigation

MODELING OF THE WIND GENERATED FORCE ACTING ON THE LIFERAFT Relation between forces and moments in both coordinate systems are presented in table. Table. Relation between forces and moments for wind direction system and liferaft main axis system X = X cosβ Y sinβ Y = Y cos β + X sin β MX = MX cos β MY sin β MY = MY cosβ MX sin β Z = MZ Z = MZ The geometrical parameters of the -person liferaft are presented in the table 2. Table 2. Geometrical parameters of the -person liferaft Diameter [mm] Rated altitude Raft outer lower float chamber upper float chamber [mm] person 297 288 272 225 Relations between forces for different wind speed, [knts], 5 [knts], 2 [knts] and 25 [knts], as a function of wind direction, are presented in the figures Fig. 3- Fig. 5 Fig. 3. Spatial distribiution of force X for different wind speed V w (, 5, 2, 25 knts) 6/23 85

Leszek Smolarek Fig. 4. Spatial distribiution of force Y for different wind speed V w (, 5, 2, 25 knts) Fig. 5. Spatial distribiution of force Z for different wind speed V w (, 5, 2, 25 knts) 86 Annual of Navigation

MODELING OF THE WIND GENERATED FORCE ACTING ON THE LIFERAFT REGRESSION ANALYSIS OF WIND FORCES AND MOMENTS Laboratory data were analysed by statistical program Statgraf. Regression models of dependency between wind velocity and measured forces and moments were obtained. Because of very small real value of forces and moments for low speed of winds and some mistakes in measurements for very low speeds of winds, obtained models do not cover situations for wind speeds less than knots Table 4. Regression models of wind forces for the person pneumatic raft in liferaft main axis system Force X FITTED MODEL EVALUATION X max =,487 V w,93674 Correlation Coefficient R-squared Standard Error of Est. P-Value,999926 99,9853,389, X min =,46576 V w 2,5983,998658 999,737,5764, Y Y max = exp(6,4-26,466/v w ) -,998876 99,7754,39959, Y min = 64,3943-9,77679 V -,997376 99,4759 5,6,26 2,2698 Z Z max =,574729 V w Z min= (-2,23534+,87259 V w ) 2,997463 99,4932,7828,25,998987 99,7976,3679, Table 5. Regression models of wind forces moments for the person pneumatic raft in liferaft main axis system Moment FITTED MODEL EVALUATION Correlation Coefficient R-squared [%] Standard Error of Est. P- Value MX MX max = exp(5,564-27,4584/v w ) -,988485 97,73,3539,5 MXmin = /(,445 -,52492/Vw) -,99884 99,7684,85,2 MY MY max = exp(5,9938-2,7569/v w ) -,99939 99,879,37457, MY min = 29,347-2,9656 V w -,969228 93,943 4,447,38 MZ MZ max = exp(4,87989-3,794/v w ) -,99655 98,397,33395,93 MZmin = 44,4484-2,57 ln(vw) -,995642 99,33,97578,44 6/23 87

Leszek Smolarek 4 6 X min [N] 3 2 X max [N] 5 4 3 2 Fig. 6 Wind force X estimation curves -3 5 Y min [N] -7 - -5 Y max [N] 2 9 6 3-9 Fig. 7 Wind force Y estimation curves 4 8 Z min [N] 3 2 Z max [N] 6 4 2 MX max [Nm] Fig. 8 Wind force Z estimation curves -2 8 6 4 2 MX min [Nm] -4-6 -8 - -2-4 Fig. 9 Wind moment MX estimation curves 88 Annual of Navigation

MODELING OF THE WIND GENERATED FORCE ACTING ON THE LIFERAFT MY max [Nm] MZ max [Nm] 8 5 2 9 6 3 5 4 3 2 MY min [Nm] -9-9 -29 Fig. Wind moment MY estimation curves MZ min [Nm] -25 - -5-9 -3-7 -2 Fig. Wind moment MZ estimation curves CONCLUSION The results obtained from laboratory experiments allow estimating life raft s real aerodynamic drag. This statement follows from lack of wind speed influence on flow character around raft. Results got from tunnel experiments Application of wind forces and moments, estimated in the laboratory experiments for a particular raft size, will allow for more correct estimation of a raft wind heeling arm. As well they could be used in further investigations of raft modifications and designing especially drag force X, side force Y and yawing moment MZ. The others aerodynamical loadings lift force Z, rolling moment MX and pitching moment MY have a less influence on raft stability. The deformation of liferaft canopy disturbs all wind s forces and moments. Spatial distributions of wind s forces show that unexpected change of a wind direction affects the liferaft stability. 6/23 89

Leszek Smolarek REFERENCES. Blendermann W. Parameter identification of wind loads on ships Journal of Wind Eng. & Ind. Aerodyn. 5, 994 2. Blendermann W. Estimation of Wind Loads on Ships in Wind with a strong Gradient OMAE Vol. A, Offshore Technology ASME, 995 3. Davenport G. The spectrum of horizontal gustiness near the ground in high winds Quarterly Journal of the Royal Meteorological Society, vol. 87, 96 4. International Aeronautical and Maritime Search and Rescue Manual (IAMSAR Manual), IMO/ICAO, London/Montreal, 999. 5. Raport z badań Badania aerodynamiczne pneumatycznych tratew ratunkowych w tunelu aerodynamicznym 5m Raport nr 68/BA/2/D Instytut Lotnictwa Warszawa 2 6. Smolarek L. - An example of non-linear leeway for the life raft, Proc. International Congress of Seas and Oceans, Szczecin-Miedzyzdroje 2,Vol. 7. Smolarek L. (2). Przerwanie liniowości ruchu obiektów poszukiwanychtratwy ratunkowe, 2, Sympozjum SAR "Poszukiwanie i Ratowanie Życia na Morzu", statek badawczo-szkoleniowy "Horyzont II", Gdynia 2 8. Smolarek L - Wpływ sił wiatrowych na tratwę, Proc. VI Konferencja Naukowo- Techniczna Bezpieczeństwo Morskie i Ochrona Środowiska Morskiego, Kołobrzeg 22,Vol. Received October 23 Reviewed December 23 9 Annual of Navigation