ASSEMBLY INSTRUCTIONES www.quebecbillard.com
PARTS IDENTIFIER 1 2 3 4 5 Side Apron-A Side Apron-B Playfield Center Support Left Leg 6 7 8 9 10 11 Right Leg End Apron Leg End Panel Leg Side Panel 12 13 14 15 5/16" Flat Washer 24 Pieces 5/16" Bolt 24 Pieces 1/2" Round Head Screw - Silver 8 Pieces 5/8" Round Head Screw 1 Playfield End Tray 16 17 18 19 20 3/4" Bolt Nut 1/4" Round Head Screw 30 Pieces 1/2" Round Head Screw - Black 20 Pieces Goalie Control 21 22 23 24 25 Gear 10 Pieces Allen Key s Rod Stopper 10 Pieces Rod Bushing 10 Pieces Rod Handle 10 Pieces 26 27 28 29 30 Long Rod 4 Pieces Medium Rod Short Rod 4 Pieces Long Stick Blue Player Short Stick Blue Player 31 32 33 34 35 Medium Stick Blue Player 3 Pieces Blue Goalie s Long Stick Red Player s Short Stick Red Player Medium Stick Red Player 3 Pieces 36 37 38 39 40 Red Goalie s Control Box Apron Corner Apron Corner with Scorer Leg Leveler 4 Pieces Puck Catcher with Sensor Wire 1 www.quebecbillard.com
PARTS IDENTIFIER 41 42 43 44 45 Goal Side PMMA End PMMA Puck L Bracket 46 47 Pre-installed 48 Pre-installed 49 Pre-installed 50 Pre-installed 1" Round Head Screw 4 Pieces Long Puck Catcher Wire with Sensor Short Puck Catcher Wire with Sensor Long Scorer Display Short Scorer Display 51 52 3 x 6mm Round Head Screw Allen Wrench! 1) Require 3pcs AAA Batteries (Not included). 2) Do not mix old and new batteries. 3) Do not mix alkaline, standard (carbon zinc), or rechargeable (nickel-cadmium) batteries. 2 www.quebecbillard.com
ASSEMBLY INSTRUCTIONS 1. Find a clean, level place to begin the assembly of your Rod Hockey table. The table will be assembled upside down and then turned over on its legs once the assembly completed. This game table is heavy, and turning it over will require at least two strong adults. 2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the parts identifier below. Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your work surface. FIG.1 3. Attach one Left Leg (#5) and Right Leg (#6) to the Side Apron-A (#1) using two Bolts (#11) and two Washers (#10) per Leg. See FIG. 1. FIG.2 #11 FIG.1 #10 #6 #11 #1 #5 #10 FIG.2 4. Attach the End Apron (#7) to the Leg Assemble (previously assembled) using two Bolts (#11) and two Washers (#10) per Leg. See FIG. 2. FIG.2 #7 #11 #10 3 www.quebecbillard.com
FIG.3 5. Slide the Playfield (#3) into the grooves of the End Aprons and Side Apron-A and attach the Side Apron-B(#2) to the End Aprons (#4). See FIG 3. #3 FIG.3 #2 4 www.quebecbillard.com
FIG.4 6. Attach the Left Leg (#5) and Right Leg (#6) to the Apron using four Bolts (#11) and four Washers (#10) per Leg. See FIG.4. #11 FIG.4 #6 #10 #11 #10 #5 #11 #10 FIG.5 7. Insert Gear (#20) into the player groove on the underside of Playfield (#3). See FIG 5. #20 #20 FIG.5 5 www.quebecbillard.com
FIG.6 8. Slide all Player Rods (#25, #26, #27) throught Rod holes in the End Apron. See FIG.6. 9. Push the Gear (#20) into the corresponding Player Rod using two Screw (#17) per Gear. See FIG.6A. 10. Attach the Rod Stopper (#22) to the Player Rod using one Screw (#17) per Rod Stopper. See FIG.6B. 11. Slide the Rod Bushing (#23) onto the Player Rod from outside of the main cabinet. See FIG.6. 12. Slide the Rod Handle (#24) onto the Player Rod after the Rod Bushing. See FIG.6. FIG.6 FIG.6B #17 #23 #24 FIG.6A #22 #17 #20 Long Rod (25) Short Rod (27) Medium Rod (26) #17 Short Rod (27) Long Rod (25) Long Rod (25) Short Rod (27) Medium Rod (26) Short Rod (27) Long Rod (25) 6 www.quebecbillard.com
FIG.7 13. Slide the Goalie Control (#19) through the Goalie hole in the End Apron, secure the Goalie Control (#19) to the underside of the Playfield (#3) using the Bolt (#15) and Nut (#16). See FIG 7A. 14. Attach the Puck Catcher (#40) to the End Apron (#7) using four Screws (#18) per Puck Catcher. See FIG 7B. 15. Place the Center Support (#4) to the underside of Playfield (#3) using two L Brackets (#45) and two Screws (#18). See FIG 7.C. FIG.7 FIG.7B #40 FIG.7A FIG.7C #18 #18 Step2 #45 #19 Step1 #4 #16 #19 #15 FIG.8 16. Attach the Control Box (#36) to the Side Apron-B (#2) using four Screws (#18). See FIG 8. 17. Attach the Leg End Panel (#8) between Left Leg and Right Leg using six Screws (#13) per Leg End Panel. 18. Attach the Leg Side Panel (#9) between Left Leg and Right Leg using four Bolts (#11) and four Washers (#10). 19. Attach the Leg Levelers (#39) at the bottom of each leg. #11 #10 #39 #8 #9 #13 #13 #13 #9 #8 #36 #18 #11 #10 7 www.quebecbillard.com
FIG.9 20. Attach the Goal (#41) to the end of playfield using two Screws (#46) per Goal. See FIG.9. 21. Slide the Side PMMA (#42) into the slot pre-set on the Side Apron. See FIG.9. 22. Slide the End PMMA (#43) into the slot pre-set on the End Apron. See FIG.9. 23. Insert each Player (#28,#29,#30,#32, #33, #34) into each metal tap on the Gear (#20). See FIG.9, 9A and 9B. 24. Insert each Goalie (#31, #35) into each Goalie Control (#19). SeeFIG.9 and 9A. FIG.9 #46 #46 FIG.9B #41 #42 #29 #34 #35 #43 #32 #30 #31 #34 #30 #34 #28 #30 #33 FIG.9A ORDER OF PLAYERS (Overhead View) 32 29 31 34 30 34 30 35 33 30 34 28 = BLUE = RED 8 www.quebecbillard.com
FIG.10 25. Attach the Apron Corner (#37) to the top of Leg using two Screws (#12).See FIG.10. 26. Attach the Apron Corner with Scorer (#38) to the top of Leg using two Screws (#12).See FIG.10. 27. Attach the Playfield End Tray (#14) to the end of the playfield using the Screw (#51). See FIG.10. Repeat the same at the opposite side. 28. Insert the Sensor Wire from Puck Catcher (#40) into the Control Box (#36). See FIG. 10A. 29. Insert the Scorer Wire from Scorer (#11) into the Control Box (#36). See FIG.10A. #12 #38 #51 FIG.10 #14 #37 #37 FIG.10A Scorer Wire Sensor Wire Scorer Wire #36 Self-Stick Strap Self-Stick Strap NOW YOU ARE READY TO PLAY! 9 www.quebecbillard.com