BRAND OVERVIEW 06 FRAME FEATURES 08 GEOMETRY 0 MAINTENANCE SCHEDULE 2 SETUP OVERVIEW 2 TECHNICAL ASSEMBLY OVERVIEW 4 EXPLODED VIEWS REBUILD KITS 6 LEGAL WARRANTY 30 CONTACT INFORMATION 3 4. 5.
We are confident your new bicycle will exceed your expectations for value, performance, and ride quality. Each frameset and component has been custom specified and designed to enhance your riding experience. Whether you are a beginner cyclist, or a seasoned pro, your Yeti bicycle will provide endless hours of two-wheeled fun. This manual outlines basic setup and maintenance recommendations of your new Yeti. Because it is impossible to anticipate every situation or condition that may occur during the assembly, setup, and maintenance of your bicycle, Yeti recommends that all service and repairs be performed by your local authorized Yeti Dealer. This model specific manual is designed to be used in conjunction with the general Yeti Owner s Manual and the manuals supplied by the suspension manufactures. If you did not receive the Yeti owner s manual or the manual provided by the suspension manufacturer download the materials off the Internet, or contact your local dealer. Bicycling can be a hazardous activity even under the best of circumstances. Proper maintenance of your bicycle is your responsibility and when done properly helps reduce the risk of injury and damage to your bicycle. This manual contains many Warnings and Cautions concerning the consequences of failure to maintain or inspect your bicycle. The word Warning indicates a potentially hazardous situation in which, if not avoided, could result in serious injury or death. The word Caution indicates a potentially hazardous situation in which, if not avoided may result in minor injuries or damage to your bicycle or a component of your bicycle. Be sure to read and understand all of the Warnings and Cautions listed in the manual. Warning: Make sure you review and understand the warnings, instructions, and content of this manual and accompanying manuals for your bicycle. Warning: Technological advances have made bicycles and bicycle components more complex and the pace of innovation is increasing. It is impossible for this manual or the accompanying manuals to provide all the information required to properly repair and/or maintain your bicycle. In order to help minimize the chances of an injury, it is critical for you to have work performed by an authorized Yeti retailer. 6. 7.
. SWITCH INFINITY TECHNOLOGY PATENTED SUSPENSION SYSTEM 2. HIGH MODULUS CARBON FIBER MAIN FRAME AND SWING ARM 3. COLLET AXLE SYSTEM ON PIVOTS REDUCES BEARING WEAR 4. OPTIMIZED FOR X DRIVETRAINS ONLY 5. ISCG 05 CHAINGUIDE MOUNTS 6. INTERTED ED TBE 4/5 7. SUSPENSION BY FOX 8. CUSTOM DEBRIS AND CHAIN SLAP GUARDS 9. INTERNAL CABLE ROUTING 0. INTEGRATED AXLE AND DERAILLEUR HANGER SYSTEM 3 4 5 6 8 9 The SB30 delivers 30 of travel with our patented Switch Infinity Technology. Efficient pedaling performance while still smooth and continuous when the going gets rough. High modulus carbon provides a stiff, strong and light weight chassis. Colleted pivot axles help create a stiff interface between the front and rear triangles of the frame. Custom Enduro Max sealed bearings keep things moving freely at the pivots. The SB30 does away with the front derailleur mount, making it a x drive specific frame. This increases stiffness in the frame, making the SB30 one of the stiffest bikes in our lineup. ISCG 05 chain guide mounts are included on the SB30 if case you want to go for some extra drivetrain security in the rowdy sections. Using our head tube on the SB30 allows for a larger head tube with more area, increased stiffness, and lower overall ride height without compromising any performance. T SB30 0 55 DP shock, by Fox Racing Shox. Custom guards on the seat stay, chain stay and down tube keep things quiet while riding and protect the frame. The SB30 features internal routing for all cables, making the bike quiet and clean looking as well as reducing cable rub on the paint. 0 Dedicated 2 x 48 Boost dropouts and integrated hanger with axle threads for strength, stiffness, ease of hanger and wheel installation. 8. 9.
S MD LG XL A WHEEL 29 29 29 29 B REACH 430 460 480 505 C EFF. TOP TUBE 50 609 65 6534 D STACK 60 648 648 6348 E HEAD TUBE LENGTH 95 99 0 F SEAT TUBE LENGTH 380 40 450 495 G EFF. SEAT TUBE ANGLE 0 69 69 H HEAD TUBE ANGLE 655 655 655 655 I EST. BB HEIGHT 336 33 33 33 J CHAINSTAY LENGTH 433 433 433 433 K FRONT-CENTER 409 6 9 86 L WHEELBASE 39 056 30 59 M STANDOVER 35 59 8 306 N ALXE TO CROWN 55 55 55 55 O FORK OFFSET 44 44 44 44 *All measurements are in millimeters SMALL MEDIUM LARGE X-LARGE 5'3" (60 CM) - 5'" (0 CM) 5'7" (70 CM) - 5'" (80 CM) 5'" (80 CM) - 6'3" (9 CM) 6'" (85 CM) - 6'6" (98 CM) 0..
Following these guidelines will help maintain the performance of your bicycle and prevent more serious problems from arising. It is important to remember that service intervals can vary depending on climate, trail conditions and riding frequency. If you are unsure about working on your own bicycle, contact your authorized Yeti Dealer for more information on general bicycle maintenance. Yeti strongly recommends using a torque wrench when assembling your frame. Torque specifications for individual parts on the SB30 are listed below, as well as in the step by step assembly instructions later in the manual. For general bicycle maintenance please consult the torque specifications of the component you are adjusting. CLEAN AND LUBE CHAIN CHECK TIRE PRESSURE CLEAN BIKE OF MUD AND DEBRIS CHECK BRAKE FUNCTION CHECK SHOCK PRESSURE, IF APPLICABLE CHECK FOR LOOSE BOLTS AND TIGHTEN, IF NECESSARY CHECK HEADSET AND TIGHTEN / LOOSEN, IF NECESSARY THOROUGHLY CLEAN PIVOT POINTS WITH A RAG (DO NOT LUBRICATE) LUBE INFINITY LINK EVERY 40 HRS. (YETI HEAVY MOLYBDENUM GREASE) CHECK / REPLACE BRAKE PADS, IF NECESSARY WEEKLY MONTHLY 3 MONTHS ANNUALLY PART NUMBER DESCRIPTION TORQUE (NM) 300040485 IN PIOT LE 35 00003 SS PIOT BOLT ELE 5 30003096 COLLET LE 30505 00 300040486 COLLET WEDE BOLT LRE 4 30003093 LIN PIOT RDWRE LE 5 8 30006003 48 DERILLER NER 9 30003005 SCS 60 0L SWITC LIN ONT 300040486 COLLET WEDE BOLT SLL 8 3000305 BOLT TI LE 6 0 CHECK TIRES FOR WEAR CHECK SPOKE TENSION AND RETENTION, IF NECESSARY CHECK CHAIN FOR WEAR AND REPLACE IF NECESSARY COMPLETE TUNE-UP PERFORMED BY AN AUTHORIZED YETI DEALER 2. 3.
03. Push your seatpost housing into the frame from the headtube port until it exits near the access port. 04. Outside of the access port, connect the Park router tool to the housing. 0. With a 3mm allen key, remove the lower cable port access cover near the bottom bracket. 02. Install your seatpost housing into the head tube port, pushing until it exits near the lower cable port access hole. 05. Pull router tool back through the frame until your housing exits the seat tube. 0. Route a section of shifter housing through the frame using the steps described in Standard Setups 03. Use your finger to help push the housing around the bend in the frame up into the seat tube. 04. While pushing the housing into the head tube port, continue pushing the cable up the seat tube through the access port until the housing exits the seat tube. 02. Connect the double-barb to the shifter housing and the seatpost housing at the seat tube. 03. At the same time, pull the shifter housing out of the head tube port while pushing the seatpost housing into the seat tube until the double barb exits the head tube. 0. Remove the lower cable port access cover with a 3mm allen key. 02. Drop a Park Tool Router tool down the seat tube until it exits the access port. Push the brake line into the frame starting at the rear triangle, feeding it forward to the ports into the front triangle and out the head tube. Push the shifter housing into the lower head tube port on the non-drive side. Feed the housing back to the ports on the rear triangle and eventually out near the drive-side dropout.
0. With a 5mm allen wrench, remove the main pivot Collet Wedge Bolt 02. With a 0mm allen wrench, remove the Main Pivot Collet Axle. The Collet Nut on the drive side can remain in the frame. 05. Wipe off any excess grease that was pushed out of the seals. 06. Lower the swingarm and re-install your Main Pivot Collet Bolt Torque 3.5 Nm 03. Rotate your swingarm upwards to access both grease zerks and expose the whole Switch Infinity link. With a clean rag and mild detergent, clean any mud, dust, or debris off the Switch Infinity Link. 04. Using a needle-type grease gun, push new grease into the two Switch Infinity grease ports until you see grease extruding from the shaft seals. 07. Install the Main Pivot Collet Wedge and torque to 4 Nm..
Make sure your tools are in good condition. A worn allen key can round the hex on a bolt not allowing for proper torque. Torque settings are listed throughout the instructions. It is important to prep all bolt threads. The instructions denote whether to use a Loctite compound or grease. 3mm allen key 4mm allen keys 5mm allen keys 6 0mm allen key Guide pin tool (Or two) C Torque wrench Grease Blue (242) Loctite 0. All the parts you ll need to get your SB30 frame assembled. Please refer to the exploded view later in this manual for more information. 0. P S E S Warning: Service on Yeti bicycles requires special knowledge and tools. Yeti Cycles recommends that all service and repairs be performed by an authorized Yeti Dealer 0. R T S S P I B L (2000203) 0. S 4 W 3000304 4 6 C S (3000300) B L 4 *Torque to 3Nm. I 4 C S I L O S I L.
0. I S I L S W T T 4 Nm 0. E B R 300040505 P L S E 00003 000033 0. S 4 T W 300030069 L/E S T B 3000305 W 30003006 B L Torque to Nm. 0. P L E O L 00003 S P 0. L P B 000038 L P B 30003093 P L T L P B I L P B Torque to 8Nm...
0. R T P P C 300040485 S R T S I L P C 300040485 I C N 30003085 *Torque to rou 3. Nm. R S L S E I B 00003 B D B L. T S P B 5 Nm R. L C W B 300040454 I P Torque to Nm. S P B 000036 B L 4 B 000036 I S P B 000036 R T. O L S E S E S P. C 30003096 I L E S E *Torque to Nm..
. C W B 300040486 C Torque to 8 Nm.. I 45 T B 3000309 W 300030069. B L 4 B 30003099 I L C P C 300040504 B 0. D 30006003 I R T C 30006005 ASSA *Torque to Nm *Torque to Nm https://www.yeticycles.com/bikes/sb30/? guide:support-shock-setup. B L 4 T B 3000305 S T B W 30003006. I W 30003048 0 B 30003000 I rou Nm. Torque to Nm..
. 2. 2.3 2.2 4.30.2 4.30. 4.2 4.0 4. 4.8 4.9 4.7 4.25 4.24 4.27 4.28.3. 4.5 4.7.2 4.9 4.8 3 4.4 4.3 4.22 4.2.2 4.20. 4.3 4.6 4.7 4.23. 4.6 4.9 4.8 4..2 4.5 4.. 4.2 4.4 4.26 4.29 2.4 PREP KEY LOCTITE GREASE 4.20.2
ITEM# PART # DESCRIPTION QTY ITEM# PART # DESCRIPTION QTY 4 30003085 COLLET NT 5 5 N/A SB30 FRONT TRIANGLE ASSEMBLY 43 30003096 COLLET LE 305 05 0 0. N/A SB30 FRONT TRIANGLE 44 300040486 COLLET WEDE SBSSEBL 0.2 300070006 ICE AXE HEAD BADGE 44 30003084 COLLET BOLT 5 8.3 4000086 DT PROTECTOR 44 30003083 COLLET WEDE 0 2 N/A SB30 SWING ARM ASSEMBLY 443 30004048 SPIRL RETININ RIN 05 0 INCES 2. N/A SB30 SWING ARM 45 3000309 BOLT STER TI ELE 8 450 2.2 400008 SB30 PROTECTOR CS/SS 2.3 4000088 SB30 PROTECTOR CS LOWER 2.4 4000093 SB30 CS PROTECTOR INNER 3 N/A 30 OC E 46 30003098 BOLT STER TI ELE 8 40 4 300030069 WSER 85 5 05 48 3000305 BOLT TI LE 6 0 49 30003006 WSER 65 5 05 N/A 30 PRT E 4 000030 SB30 LIN SBSSEBL 40 00003 SSEBL SOC ETENDER TOP 60 40 30004050 SOC ETENDER TOP 60 4 300040500 SB30 LIN 40 3000003 BERIN 398 DBL 890/ 4 3000005 BERIN 690RS ETENDED 5 8 /0 4 000033 SSEBL SOC ETENDER BOTTO 60 4 000036 BOLT SS PIOT ELE 4 300040503 SOC ETENDER BOTTO 60 43 00003 LIN PIOT RDWRE EED LON 4 3000003 BERIN 398 DBL 890/ 44 00003 LOCRIN 690RS 4 300040505 SOC ETENDER BERIN ETENSION 45 30003093 LIN PIOT RDWRE LE 5 43 30006008 SSEBL ETI SET CLP BOLT ON 36 46 000038 STD LIN BERIN ELE 5 43 N/ COLLR BOLT ON ETI SET CLP 36 4. 00000 SWITC ININIT ECNIS 43 N/ BRREL NT ETI SET CLP BOLT ON 4.8 30003005 BOLT 6 0 0L 4 433 30003000 BOLT 5 08 6L 4.9 3000304 WSER 630 4 44 300040504 CBLE PORT COER 4.0 300040485 COLLET LE 5 45 30003099 BOLT LT ED 5 08 6 4 300040454 COLLET WEDE SBSSEBL 5 46 3000005 BERIN 690RS ETENDED 5 8 /0 4. 30003068 COLLET BOLT 8 5 4 30003000 BOLT 5 08 6L 4 3000306 COLLET WEDE 5 48 30003048 WSER 5 89 0 43 300040450 SPIRL RETININ RIN 03 0349 INCES 49 300030300 SOC EELET SPCER 430 30006004 DER NER 3 STNDRD. 43 30006005 DER NER CP 3
PART # DESCRIPTION QTY PART # DESCRIPTION QTY 200020333 30 TER RE T 00003 LOCRIN SS PIOT 00003 SOC ETENDER 60 TOP W/BERIN 000033 SOC ETENDER 60 BOTTO W/BERIN 000036 BOLT SS PIOT ELE 00003 LIN PIOT RDWRE EED LON 2 000038 STD LIN BERIN ELE 5 485L 30000045 BERIN 690 RS 85 OT 2 3000005 BERIN 690 LL E 4 30003005 BOLT CP 60 4 30003006 WSER SS 65 ID 5 300030069 WSER SS 85 ID 5 3000305 BOLTTILE 6 3000304 WSER 0 6 4 30003085 COLLET LE NT 55 30003093 LE LE 5 6 00 30003096 COLLET LE 30505 00 3000309 BOLT STER TI ELE 8 450 30003098 BOLT STER TI ELE 8 40 20002033 30 RRE T 00003 LOCRIN SS PIOT 00003 SOC ETENDER 60 TOP W/BERIN 000033 SOC ETENDER 60 BOTTO W/BERIN 000036 BOLT SS PIOT ELE 00003 LIN PIOT RDWRE EED LON 2 000038 STD LIN BERIN ELE 5 485L 30003005 BOLT CP 60 4 30003006 WSER SS 65 ID 5 300030069 WSER SS 85 ID 5 3000305 BOLTTILE 6 3000304 WSER 0 6 4 30003085 COLLET LE NT 55 30003093 LE LE 5 6 00 30003096 COLLET LE 30505 00 3000309 BOLT STER TI ELE 8 450 30003098 BOLT STER TI ELE 8 40 30003099 BOLT LT ED 5 08 6 300030300 SOC EELET SPCER 300040454 COLLETWEDE SSEBL EN 300040485 LE COLLET 555S3T 300040486 COLLETWEDE SSEBL 0 300040504 CBLE PORT COER 300040505 SOC ETENDER BERIN ETENSION 30003099 BOLT LT ED 5 08 6 300030300 SOC EELET SPCER 300040454 COLLETWEDE SSEBL EN 300040485 LE COLLET 555S3T 300040486 COLLETWEDE SSEBL 0 300040504 CBLE PORT COER 20002033 30 ER RE T 3000003 BERIN 398 RS DBL ROW 30000045 BERIN 690 RS 85 OT 3000005 BERIN 690 LL E 4. 300040505 SOC ETENDER BERIN ETENSION.
PART # 200020039 DESCRIPTION 30 PORT COVER T QTY 30003099 BOLT LT ED 5 08 6 300040504 CBLE PORT COER 00009 30 E PROTECTOR T 4000086 SB30 DT PROTECTOR 400008 SB30 CS/SS PROTECTOR 4000088 SB30 CS LOWER PROTECTOR 300040493 SB30 CS INNER PROTECTOR
HERE S EVERYTHING YOU NEED TO KNOW ABOUT OUR LIFETIME WARRANTY: All 209 (or newer) frames, including the Switch Infinity, are covered for life against damage due to manufacturing defects for the original purchaser. Paint and finish are covered for -year. We will repair or replace, at our discretion, any frame we deem defective. There are a few conditions: you must register it online at YetiCycles.com and you must take it to an authorized Yeti Cycles dealer for processing. Warranty does not cover damage due to ordinary wear and tear, neglect or intentional destruction. From a slingshot or your truck. DISCLAIMER YETI Cycles is not responsible for any damages to you or others arising from riding, transporting or other use of your bicycle. In the event that your frame breaks or malfunctions, YETI Cycles shall have no liability or obligation beyond the repair or replacement of your frame pursuant to the terms outlined in the warranty. *If you have a warranty concern, please contact your authorized Yeti dealer. If you happen to have a crash or non-warranty situation, we ll get you back on the trail with a reasonable replacement price. Same conditions as above. Lifetime Warranty applies to all 209 and newer frames (including the SB00). Model year 208 and older frames will be covered under our previous warranty (5-year or 2-year based on time of purchase). Simple as that. No fine print. YETI CYCLES 62 Corporate Circle, Unit B Golden, CO 8040 (p) 303-278-6909 (f) 303-278-6906 www.yeticycles.com BUSINESS HOURS Monday-Friday 8AM-:30AM, :00PM-5:30PM (Mountain Time).