P -E L P -C L P -H L C P -B L C MULTIPLE CHNNELS ORIENTTION MULTIPLE CHNNELS ORIENTTION 2 MULTIPLE CHNNELS ORIENTTION 1 P -B L P -E L P L -C P L -H P - L B B SINGLE CHNNEL ORIENTTION SINGLE CHNNEL ORIENTTION 2 SINGLE CHNNEL ORIENTTION 1 DTE MODIFIED: SCLE: 1/4 = SINGLE & MULTIPLE DRINGE CHNNELSIDEWLK CULVERT GENERL SSEMBLIES DWG. NO. SW-01 SHT 1 of 6 NOV 15 2012
2'-2 1 4 (ORIENTIONS 2&) 2'-0 (ORIENTION 1) SLOPE CULVERT TOWRD STREET @ 2%TO MTCH SIDEWLK CROSS SLOPE IN EXISTING CURB ONLY DRILL 4 DEEP. GROUT IN #4 DOWELS @ 12 SPCING. CURB CUT SECTION - MTCH TO TOP OF CURB INVERT OF CULVERT TO MTCH BOTTOM OF CURB CUT. 2' [(2'*N)+(4 1/2)*(N-1)] WHERE N= # OF CHNNELS 2 4 1 2 MIN 2' 2' SECTION B-B SECTION C-C DTE MODIFIED: SCLE: 1/4 = SIDEWLK CULVERT CONCRETE WORK DWG. NO. SW-01 SHT 2 of 6 NOV 15 2012
TRIMMED S SHOWN BELOW (6 PLCES) - 10 TRIMMED S SHOWN BELOW (6 PLCES) TOP SIDE DIMOND PLTE PLTE SSEMBLY SCLE: = SCLE: = DIMOND PLTE TOP SIDE PLTE SSEMBLY B (S SHOWN) PLTE SSEMBLY C (OPPOSITE HND) 1 16 CHMPHER 5 16 TRIMMED 1 4 HEX BOLT SCLE: = DTE MODIFIED: SIDEWLK CULVERT DIMOND PLTE SSEMBLIES DWG. NO. SW-01 SHT of 6 NOV 15 2012
TRIMMED S SHOWN ON SH ( PLCES ) 1 4 TRIMMED S SHOWN ON SH ( PLCES ) 2' CONNECTING BRCKET CONNECTING BRCKET 1 4 DIMOND PLTE TOP SIDE PLTE SSEMBLY D DIMOND PLTE SCLE: = SCLE: = TOP SIDE PLTE SSEMBLY E (S SHOWN) PLTE SSEMBLY H (OPPOSITE HND) DTE MODIFIED: SIDEWLK CULVERT DIMOND PLTE SSEMBLIES DWG. NO. SW-01 SHT 4 of 6 NOV 15 2012
1 4 6 BR 2' 4 REF BRCKET BEND DETIL 7 16 7 5 1 1 4 2 SYMMETRY BOUT C L 2'-7 1 4 BRCKET FLT LYOUT SCLE: = DTE MODIFIED: SIDEWLK CULVERT SUPPORT BRCKET DWG. NO. SW-01 SHT 5 of 6 NOV 15 2012
CONSTRUCTION ND FBRICTION NOTES: 1) LL EXPOSED CONCRETE SURFCES SHLL MTCH GRDE COLOR ND FINISH OF DJCENT CURB ND SIDEWLK. 2) STEEL SURFCE PREPRTION SHLL MEET SSPC-SP6 STNDRD. ) PINT STEEL SURFCES WITH ONE COT OF RED OXIDE ND TWO FINISH COTS OF LUMINIUM PINT (SHTO M69) INSTLLTION NOTES: 1) INSTLL 1 2 EXPNSION JOINT BETWEEN CULVERT ND SIDEWLK. ORIENTTION 1 2) INSTLL PLTE SSEMBLY D BY SLIDING THE TTCHED SLOTTED BRCKET UNDER THE PREVIOUS PLTE SSEMBLY ENGGING THE BOLTS OF THE PREVIOUS SSEMBLY WITH THE BRCKET. ) REPET THIS PROCEDURE UNTIL SUFFICIENT PL-D SSEMBLIES HVE BEEN INSTLLED TO SPN THE DISTNCE FROM THE BCK OF CURB TO THE OPPOSITE SIDE OF THE SIDEWLK. 4) INSTLL SUPPORT BRCKET UNDER THE LST PL-D SSEMBLY BY ENGGING THE PL-D SSEMBLY BOLTS IN THE SLOTS OF THE SUPPORT BRCKET. 5) NCHOR THE SUPPORT BERCKET WITH TWO EXPNSION NCHORS. ORIENTTION 2 6) INSTLL PLTE SSEMBLY D BY SLIDING THE TTCHED SLOTTED BRCKET UNDER THE PREVIOUS PLTE SSEMBLY ENGGING THE BOLTS OF THE PREVIOUS SSEMBLY WITH THE BRCKET. 7) REPET THIS PROCEDURE UNTIL SUFFICIENT PL-D SSEMBLIES HVE BEEN INSTLLED TO SPN THE DISTNCE FROM THE BCK OF CURB TO THE OPPOSITE SIDE OF THE SIDEWLK. ) INSTLL ONE PL-H SSEMBLY IN THE SME MNNER. 9) INSTLL SUPPORT BRCKET UNDER THE PL-H SSEMBLY BY ENGGING THE PL-H SSEMBLY BOLTS IN THE SLOTS OF THE SUPPORT BRCKET. 10) NCHOR THE SUPPORT BERCKET WITH TWO EXPNSION NCHORS. ORIENTTION 11) INSTLL PLTE SSEMBLY D BY SLIDING THE TTCHED SLOTTED BRCKET UNDER THE PREVIOUS PLTE SSEMBLY ENGGING THE BOLTS OF THE PREVIOUS SSEMBLY WITH THE BRCKET. 12) REPET THIS PROCEDURE UNTIL SUFFICIENT PL-D SSEMBLIES HVE BEEN INSTLLED TO SPN THE DISTNCE FROM THE BCK OF CURB TO THE OPPOSITE SIDE OF THE SIDEWLK. 1) INSTLL ONE PL-E SSEMBLY IN THE SME MNNER. 14) INSTLL SUPPORT BRCKET UNDER THE PL-E SSEMBLY BY ENGGING THE PL-H SSEMBLY BOLTS IN THE SLOTS OF THE SUPPORT BRCKET. 15) NCHOR THE SUPPORT BERCKET WITH TWO EXPNSION NCHORS. DTE MODIFIED: SIDEWLK CULVERT NOTES DWG. NO. SW-01 SHT 6 of 6 NOV 15 2012