SECTION 1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER Product Name: LOCTITE 7255 (PART A) Proper Shipping Name: None allocated Product Code(s): 1308499 Part Number(s): Use: 1161707 (900ml dual pack) Two-part epoxy adhesive. LOCTITE 7255 PART A is used in conjunction with LOCTITE 7255 PART B Supplier: HENKEL AUSTRALIA PTY. LIMITED ABN 82 001 302 996 ADHESIVE TECHNOLOGIES 135-141 Canterbury Road, Kilsyth, Victoria, 3137. Tel:(03) 9724 6444 24 HOUR EMERGENCY CONTACT NUMBER: Tel:(03) 9724 6556 SECTION 2. HAZARDS IDENTIFICATION STATEMENT OF HAZARDOUS NATURE: Hazardous according to the criteria of ASCC. This material has been classified as Irritant (Xi) and Dangerous for the Environment (N). Risk phrase(s): R36/38 Irritating to eyes and skin. R43 May cause sensitisation by skin contact. R51 Toxic to aquatic organisms. R53 May cause long term adverse effects in the aquatic environment. Safety phrase(s): S24/25 Avoid contact with skin and eyes. S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S28 After contact with skin, wash immediately with plenty of soap suds. S37/39 Wear suitable gloves and eye/face protection. S46 If swallowed, seek medical advice immediately and show this container or label. S61 Avoid release to the environment. Refer to special instructions / safety data sheets. DANGEROUS GOODS INFORMATION: Not classified as Dangerous Goods according to the criteria of the Australian Code for the Transport of Dangerous Goods by Road and Rail (ADG Code). SUSDP POISON SCHEDULE: 5 SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS INGREDIENTS: CHEMICAL ENTITY CAS NO. PROPORTION Bisphenol-F epichlorohydrin [9033-36-5] 30-60% w/w Silicon carbide [409-21-2] 10-30% w/w Epoxy resin [25068-38-6] 10-30% w/w 1,4-Bis (2,3-epoxypropoxy)butane [2425-79-8] 5-10% w/w Modified siloxane 1-5%w/w Wax mixture 1-5%w/w Page 1 of 4 PRODUCT NAME: LOCTITE 7255
SECTION 4. Ingestion: Skin: Eyes: Inhalation: FIRST AID MEASURES If swallowed, do not induce vomiting. Seek medical attention or contact a Poisons Information Centre (Phone 13 11 26). Remove contaminated clothing and wash affected areas with plenty of soap and water. If irritation occurs, seek medical attention. Hold eyes open and flush with water for at least 15 minutes. Seek medical attention or contact a Poisons Information Centre (Phone 13 11 26). If inhaled, remove from contaminated area. For all but the most minor symptoms, arrange for patient to be seen by a doctor. Advice to doctor: Treat symptomatically. First Aid facilities: Eye wash and safety shower SECTION 5. FIRE FIGHTING MEASURES Suitable extinguishing media: Carbon dioxide, foam, dry chemical. Hazards from combustion products: Combustible liquid. In a fire, it will emit oxides of carbon, hydrogen chloride and irritating fumes. Precautions for fire fighters and special protective equipment: If there is a risk of exposure to products of combustion, then fire-fighters should wear full protective clothing and self-contained breathing apparatus. SECTION 6. ACCIDENTAL RELEASE MEASURES Wear impervious gloves, chemical goggles and waterproof boots. For small spills, wipe up with a cloth. For larger spills, contain and collect spillage with inert absorbent materials (e.g. sand, earth, vermiculite). Transfer to sealable containers suitable for storing spilled material. Use a polar organic solvent or detergent and excess water to clean up areas in contact with spilled material. Do not contaminate watercourse. Dispose of residues in chemical waste disposal area in accordance with relevant State and Federal requirements. SECTION 7. HANDLING AND STORAGE Safe Handling: Observe recommendations made under SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION. Wear neoprene gloves and chemical splash goggles. Upon mixing the resin with hardener, the adhesive will release heat and begin to cure. Keep away from sources of ignition. Do not cut or heat empty containers, as they may contain product residue. If the cured material is cut or dry sanded, dust may be generated. In such a case, wear an approved particulate respirator. Storage: Store indoors in a cool, dry, well ventilated area away from heat, sparks and flames. Keep containers sealed when not in use. Protect from physical damage. Refrigerated storage is recommended to maintain product quality. SECTION 8. EXPOSURE CONTROLS / PERSONAL PROTECTION National exposure standards: Engineering controls: None established A local mechanical exhaust system is required where vapour or mist is being generated. Page 2 of 4 PRODUCT NAME: LOCTITE 7255
Personal protective equipment: Avoid contact with skin and eyes. Wear overalls, enclosed footwear, neoprene gloves and safety glasses or splash goggles. Use in well ventilated area. If inhalation risk exists, wear a respirator complying with the requirements of AS 1715 and AS 1716. SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES Physical data: Appearance: Green liquid Specific gravity: 1.46-1.47 Solubility: Insoluble in water VOC content < 3% SECTION 10. STABILITY AND REACTIVITY Chemical stability: Stable under normal conditions of temperature and pressure. Conditions to avoid: Avoid high temperatures, ignition sources and open flames. Incompatible materials: Keep away from acids, amines and oxidising agents. Hazardous decomposition products: When heated to decomposition, it will emit oxides of carbon, hydrogen chloride and irritating fumes. Other reactions: Under normal conditions, hazardous polymerisation will not occur. However exothermic polymerisation will occur with epoxy curing agents. SECTION 11. TOXICOLOGICAL INFORMATION HEALTH EFFECTS: Acute: Ingestion: Skin: Eyes: Inhalation: Chronic: If swallowed, this product will cause irritation to the mouth, throat and digestive tract. Contact with the skin will cause irritation. This product may cause skin sensitisation in susceptible individuals. Contact with the eyes can cause severe irritation. Inhalation of vapour may cause irritation to the nose and throat. Repeated skin contact may lead to dermatitis. Toxicity information: None available. SECTION 12. ECOLOGICAL INFORMATION Do not contaminate waterways and soil. This material is toxic to aquatic organisms and may cause long term adverse effects in the aquatic environment. SECTION 13. DISPOSAL CONSIDERATIONS Disposal of this material should be undertaken by a registered chemical disposal company. Empty containers should be scraped clean and then recycled or disposed of at an approved land waste site. SECTION 14. TRANSPORT INFORMATION Not classified as Dangerous Goods according to the criteria of the Australian Code for the Transport of Dangerous Goods by Road and Rail (ADG Code). Page 3 of 4 PRODUCT NAME: LOCTITE 7255
Sea and Air transport: UN Number: 3082 Proper Shipping Name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S (BISPHENOL F-EPICHLOROHYDRIN) Class: 9 Packing Group: III SECTION 15. REGULATORY INFORMATION SUSDP POISON SCHEDULE: 5 SECTION 16. OTHER INFORMATION Abbreviations/acronyms: ASCC - Australian Safety and Compensation Council SUSDP - Standard for the Uniform Scheduling of Drugs and Poisons DISCLAIMER: The percentage weight (% w/w) of ingredients is not to be taken as a specification guaranteed by Henkel Australia Pty. Limited, but only as an approximate guide to the content of hazardous ingredients in the material. The information contained herein does not constitute a guarantee by Henkel Australia Pty. Limited concerning the properties of the material. The information contained in this Material Safety Data Sheet is offered in good faith and has been developed from what is believed to be accurate and reliable sources. The information is offered without warranty, representation, inducement or licence and Henkel Australia Pty. Limited assumes no legal responsibility for reliance upon same. Henkel Australia Pty. Limited disclaims any liability for loss, injury or damage incurred in connection with the use of the material or its associated Material Safety Data Sheet. This information is not to be construed as a representation that the material is suitable for any particular purpose or use except those conditions and warranties implied by either Commonwealth or State statutes. Customers are encouraged to make their own enquiries as to the material's characteristics and, where appropriate, to conduct their own tests in the specific context of the material's intended use. Page 4 of 4 PRODUCT NAME: LOCTITE 7255
SECTION 1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER Product Name: LOCTITE 7255 (PART B) Proper Shipping Name: AMINES, LIQUID, CORROSIVE, N.O.S. (CONTAINS 4,4'- METHYLENEBIS CYCLOHEXYLAMINE) Product code(s): 1308499 Part number: Use: 1161707 (900ml dual pack) Two-part adhesive sprayable ceramic. LOCTITE 7255 PART B is used in conjunction with LOCTITE 7255 PART A. Supplier: HENKEL AUSTRALIA PTY. LIMITED ABN 82 001 302 996 ADHESIVE TECHNOLOGIES 135-141 Canterbury Road, Kilsyth, Victoria, 3137. Tel: (03) 9724 6444 24 HOUR EMERGENCY CONTACT NUMBER: Tel: (03)9724 6556 SECTION 2. HAZARDS IDENTIFICATION STATEMENT OF HAZARDOUS NATURE: Hazardous according to the criteria of ASCC. This material has been classified as Harmful (Xn), Corrosive (C) and Dangerous for the Environment (N). Risk phrase(s): R22 Harmful if swallowed. R34 Causes burns. R41 Risk of serious damage to eyes. R43 May cause sensitisation by skin contact. R51 Toxic to aquatic organisms. R53 May cause long term adverse effects in the aquatic environment. Safety phrase(s): S24/25 Avoid contact with skin and eyes. S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S27 Take off immediately all contaminated clothing. S28 After contact with skin, wash immediately with plenty of soap suds. S36/37/39 Wear suitable protective clothing, gloves and eye/face protection. S46 If swallowed, seek medical advice immediately and show this container or label. S61 Avoid release to the environment. Refer to special instructions / safety data sheets. DANGEROUS GOODS INFORMATION: Classified as Dangerous Goods according to the criteria of the Australian Code for the Transport of Dangerous Goods by Road and Rail (ADG Code). Class: 8 - Corrosive substance SUSDP POISON SCHEDULE: 5 SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS INGREDIENTS: CHEMICAL ENTITY CAS NO. PROPORTION Silicon carbide [409-21-2] 30-60%w/w Cyclohexanamine, 4,4 -methylenebis - [1761-71-3] 10-30% w/w Silica quartz [14808-60-7] <10%w/w Page 5 of 4 PRODUCT NAME: LOCTITE 7255
Benzyl alcohol [100-51-6] <10%w/w Formaldehyde-amine polymer [135108-88-2] <10%w/w 4-tertiary-butylphenol [98-54-4] <5%w/w Trimethylhexane-1,6-diamine [25620-58-0] <5%w/w 1,3-Benzenedimethanamine [1477-55-0] <5%w/w 1,2-Ethanediamine, N-[3-(trimethoxysilyl)propyl]- [1760-24-3] <1%w/w SECTION 4. Ingestion: Skin: Eyes: Inhalation: FIRST AID MEASURES If swallowed, do not induce vomiting. Seek immediate medical attention or contact a Poisons Information Centre (Phone 13 11 26). Remove contaminated clothing and wash affected areas with plenty of soap and water. If irritation or blistering occurs, seek medical attention. Hold eyes open and flush with water for at least 15 minutes. Seek medical attention or contact a Poisons Information Centre (Phone 13 11 26). If inhaled, remove from contaminated area. For all but the most minor symptoms, arrange for patient to be seen by a doctor as soon as possible. Advice to doctor: Treat symptomatically. First Aid facilities: Eye wash and safety shower SECTION 5. FIRE FIGHTING MEASURES Suitable extinguishing media: Carbon dioxide, foam, dry chemical. Hazards from combustion products: Combustible liquid. In a fire, it will emit toxic fumes of oxides of carbon, oxides of nitrogen and smoke. Precautions for fire fighters and special protective equipment: If there is a risk of exposure to products of combustion, then fire-fighters should wear full protective clothing and self-contained breathing apparatus. Hazchem Code: SECTION 6. 3X ACCIDENTAL RELEASE MEASURES Wear impervious gloves, chemical goggles and waterproof boots. Contain and collect spillage with inert absorbent materials (e.g. sand, earth, vermiculite). Transfer to sealable containers suitable for storing spilled material. Use a polar organic solvent or detergent and water to clean up areas in contact with spilled material. Do not contaminate watercourse. Dispose of residues in chemical waste disposal area in accordance with relevant State and Federal requirements. SECTION 7. HANDLING AND STORAGE Safe Handling: Observe recommendations made under SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION. Wear impervious gloves and chemical splash goggles. Avoid breathing vapours. Do not enter confined spaces where vapour may have collected. Keep away from ignition sources and open flames. Upon mixing Part B with Part A, the adhesive will release heat and begin to cure. Empty containers retain product residue, so obey hazard warnings. Do not cut, heat or weld containers. Storage: Store indoors in a dry, well ventilated area. Keep containers sealed when not in use. Protect from physical damage and sunlight. Store according to relevant State Dangerous Goods Storage Requirements. Refrigerated storage is recommended to maintain product quality. Page 6 of 4 PRODUCT NAME: LOCTITE 7255
SECTION 8. EXPOSURE CONTROLS / PERSONAL PROTECTION National exposure standards: None established Engineering controls: A local mechanical exhaust system is required where vapour is being generated. Personal protective equipment: Use good industrial hygiene. Avoid contact with skin and eyes. Wear suitable protective clothing, safety footwear, impervious gloves and chemical splash goggles or full face shield. Use with adequate ventilation. If inhalation risk exists, wear an organic vapour respirator complying with the requirements of AS 1715 and AS 1716. SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES Physical data: Appearance: Blue liquid Specific gravity: 1.47 Solubility: Not soluble in water. Odour: Ammoniacal Flash point: 100 C VOC content: < 3% SECTION 10. STABILITY AND REACTIVITY Chemical stability: Stable under normal conditions of temperature and pressure. Conditions to avoid: Avoid high temperatures unless curing surfaces to be bonded. Keep away from open flames and ignition sources. Incompatible materials: Keep away from acids and oxidising agents. Hazardous decomposition products: When heated to decomposition, it will emit toxic fumes of oxides of carbon, oxides of nitrogen and smoke. Hazardous reactions: Do not heat Part B at temperatures greater than 100 C. This product may release toxic gases at higher temperatures. Exothermic polymerisation will occur with epoxy resin. SECTION 11. TOXICOLOGICAL INFORMATION HEALTH EFFECTS: Acute: Ingestion: Skin: Eyes: Inhalation: Chronic: If swallowed, this product will cause serious burns to the mouth, throat and digestive tract. Other symptoms may include nausea, vomiting and abdominal pain. This product can cause burns to skin and possible allergic contact dermatitis. Contact with the eyes can cause corneal burns which may result in serious eye damage. Inhalation of vapour may cause headache, breathing difficulties and corrosive effects on the respiratory tract. This product may cause corrosive damage to skin tissue. Toxicity information: Acute Oral LD 50 (rat) : 1000 mg/kg as 4,4'-methylenebis(cyclohexylamine) Page 7 of 4 PRODUCT NAME: LOCTITE 7255
SECTION 12. ECOLOGICAL INFORMATION Do not contaminate waterways and soil. This material is toxic to aquatic organisms and may cause long term adverse effects in the aquatic environment SECTION 13. DISPOSAL CONSIDERATIONS Disposal of this material should be undertaken by a registered chemical disposal company. Empty containers should be recycled or disposed of by a registered contractor. SECTION 14. TRANSPORT INFORMATION UN Number: 2735 Proper Shipping Name: AMINES, LIQUID, CORROSIVE, N.O.S. (CONTAINS 4,4'-METHYLENEBIS CYCLOHEXYLAMINE) Class: 8, Corrosive Packing Group: III Hazchem code: 3X Emergency Information: Dangerous Goods - Initial Emergency Response Guide (SAA/SNZ HB 76) or EPG 8A1 SECTION 15. REGULATORY INFORMATION SUSDP POISON SCHEDULE: 5 SECTION 16. OTHER INFORMATION Abbreviations/acronyms: ASCC - Australian Safety and Compensation Council SUSDP - Standard for the Uniform Scheduling of Drugs and Poisons DISCLAIMER: The percentage weight (% w/w) of ingredients is not to be taken as a specification guaranteed by Henkel Australia Pty. Limited, but only as an approximate guide to the content of hazardous ingredients in the material. The information contained herein does not constitute a guarantee by Henkel Australia Pty. Limited concerning the properties of the material. The information contained in this Material Safety Data Sheet is offered in good faith and has been developed from what is believed to be accurate and reliable sources. The information is offered without warranty, representation, inducement or licence and Henkel Australia Pty. Limited assumes no legal responsibility for reliance upon same. Henkel Australia Pty. Limited disclaims any liability for loss, injury or damage incurred in connection with the use of the material or its associated Material Safety Data Sheet. This information is not to be construed as a representation that the material is suitable for any particular purpose or use except those conditions and warranties implied by either Commonwealth or State statutes. Customers are encouraged to make their own enquiries as to the material's characteristics and, where appropriate, to conduct their own tests in the specific context of the material's intended use. Page 8 of 4 PRODUCT NAME: LOCTITE 7255