F-,NO.,Lane 9,Kangning St., Shijr City,Taipei County,TAIWAN +--9-000 +--9-000 Sales Department : bb@guay.com Technology support Department : support@guay.com COPYRIGHT 0 BY G&G ARMAMENT SINCE 9 This product is intended for users years or older. Read all instructions before using this product.
WARNING WARNING Adult supervision required.always wear safety goggles when using this product. Misuse or careless handling of this product may cause injury.may be hazardous up to 0 meters. You may be liable for damaging public, personal property, injuring a person or an animal even if you only mean to shoot as a practical joke. Always observe good manners and enjoy fun sport shooting. Never direct the muzzle towards a person, animal or in any direction. That may cause harm or damage to the third party. Select a safe place for operating the air gun, avoid places where people and cars are around. Make sure to put the barrel and safety cap on the muzzle except that you are shooting. Do this to prevent accident, discharge of BBs and also for dust protection purpose. Never pull the trigger while the barrel and the safety cap is attached. Safety procedures:.attach the safety cap to the muzzle..set the selector lever to the safety position..remove the magazine..remove the battery. Looking into the muzzle is extremely dangerous regardless of BBs having been loaded or not. If you get hit in the eye by a BB pellet, you may in worst case, lose your eye sight. Operation of this air gun for competition use is restricted to users of years old or more. Careless shooting and wrong operation are dangerous, causing eye damage or other injury. When you carry the air gun, attach the safety cap, set the selector lever to the safety position and always put the air gun in a case or bag. When shooting the air guns for target practice or in a game situation, you and all participants must wear safety goggles or other eye protective gear. Also, pay attention to ricochets. It is very important to pay attention to third parties other than the participants. Always attach the safety cap to the muzzle, remove the battery and store the air gun in a case or bag and at a place that is out of reach by children. Activating the trigger carelessly is extremely dangerous. Never put your finger on the trigger unless the safety cap is removed and you are ready to shoot a target. There may be cases where some BBs remain in the gun after the magazine has been removed. After removal of the magazne, direct the muzzle towards a safe direction and pull the trigger to confirm that there are no BBs remain in the gun, then attach the safety cap. Disassembling or modifying the gun may adversely affect the performance and make it dangerous. It may be against the Law.
CONTENTS 0 0 0 0 09 9 0 9 Warning Contents RK Series Line Components New Blow Back Pneumatic System Multinational Pantents Selector & Safety Setting Battery Setting Setting Sight Adjustment Hop-Up / Motor Gear Adjustment Folding Stock Maintenance Trouble Shooting Parts List (for RK) Parts List (for RK / RK) Parts List (for RK EVO / RK EVO) Parts List (for RK BETA) Parts List (for GK99 BlowBack Ver.) RK Series line For more product information. Please visit our website RK WOOD RK RK WWW.GUAY.COM All AEG products 0% Made in Taiwan AKMS AIMS RK BETA RK EVO RK EVO GK99
COMPONENTS RK For more product information. Please visit our website WWW.GUAY.COM All AEG products 0% Made in Taiwan COMPONENTS For more product information. Please visit our website RK / RK / RK EVO / RKEVO WWW.GUAY.COM Selector Lever Selector Lever Locking Lever Bolt & Bolt Handle Grip RK / RK Handguard Set RK / RK Flash Suppressor RK / RK EVO Front Sight Upper Handguard Rear Sight Top Cover Rail Mount Rear Sling Swivel Front Sight Rear Sight Top Cover Buttstock Lower Handguard Catch Trigger & Trigger Guard Grip Buttstock Flash Suppressor RK / RK EVO Handguard Rail Set RK EVO / RK EVO Catch Trigger & Trigger Guard Tactical Grip RK EVO / RK EVO Rear Sling Swivel
COMPONENTS For more product information. Please visit our website AIMS / AKMS WWW.GUAY.COM COMPONENTS GK99 For more product information. Please visit our website WWW.GUAY.COM All AEG products 0% Made in Taiwan HandGrip AIMS Rail Mount AIMS Stock Lock Button AIMS Folding Stock AIMS Selector Lever Bolt & Bolt Handle Rear Sight Front Sight Rear Sight Top Cover AKMS Stock Lock Button Front Sight Top Cover Folding Stock Flash Suppressor Handguard AKMS Catch Folding Stock AKMS Flash Suppressor Handguard Catch Trigger & Trigger Guard Grip Trigger & Trigger Guard Grip
New Blow Back Pneumatic system BlowBack Version is Available For more product information. Please visit our website WWW.GUAY.COM Multinational Patents True to the faith of mimicking real life firearms, G&G is proud to present its new Pneumatic Blow Back system to its line of airsoft guns.conventional airsoft blow back utilizes tow hook springs to mimic real life bolt actions, which often lead to excess wear, tear and poor reliability in the gear box. To alleviate the problem of conventional systems, G&G has independently developed the Pneumatic Blow Back system; a piston driven, gas operated mechanism to better mimic real life bolt actions. This new technology utilizes compressed air to move the bolt, which enables the action without adding extra stress to the gear box. This class leading system represents a significant milestone in the airsoft industry.
SELECTOR & SAFETY SETTING BATTERY SETTING Direct the muzzle towards a safe direction and set the selector to the safety position. The magazine should be removed before changing the battery. Always set the safety lever to safety mode setting until the user is about to fire the gun. Never operate the selector while pulling the trigger. Pull the trigger with the Selector being set at safe mode may damage the air gun. Set the selector in correct position; otherwise malfunction may occur. For RK / RK / RK / RK EVO / RK EVO SAFETY ON THE TRIGGER CANNOT BE PULLED FULL AUTO AUTOMATIC FIRING SEMI AUTO SINGLE SHOT Unscrew the fixing screws and remove the plate. Connect the connector until you heard the click sound. Insert the battery and reinstall the plate. For AIMS / AKMS When not firing the gun or during storage, always set the selector to the Safe Mode and attach the protective cap on the muzzle. The gun will be fired automatically while the trigger remains being pulled. The gun will fire one shot each time when pulling the trigger. Push the rear-end of spring guide to remove the top cover. Insert battery and connect the connector until you heard the click sound. Reinstall the top cover.
BATTERY SETTING Direct the muzzle towards a safe direction and set the selector to the safety position. The magazine should be removed before changing the battery. BATTERY SETTING Direct the muzzle towards a safe direction and set the selector to the safety position. The magazine should be removed before changing the battery. For RK Beta For GK99 Press Push Press the stock plate. Push the stock plate and remove. Pull out the connector. Unscrew the handguard cap. Pull the handguard forward. Remove the handguard and pull out the connector. For RK Beta For GK99 Connect the battery plug with the connector until you heard a click sound. Insert battery into the stock. Reinstall the stock plate. Connect battery plug with the connector until you heard the click sound then insert the battey into handguard. Put the handguard back on. Tighten up the handguard cap.
SETTING MAGAZINE SIGHT ADJUSTMENT Ensure not to lose the adjustment tool. For All RK Series Confirm that the safety lever is set to the Safety position and do not place your finger on the trigger. Front Sight Adjustment For All RK Series Rear Sight Adjustment For All RK Series ( Apart from RK Beta / GK99 ) DOWN UP Always use the G&G BB pellet or diameter.9 ~.9 mm BBs for this air gun. G&G shall not be held responsible for any damage or accidents arising from the use of pellets supplied by other manufacturers. Push the magazine catch to release the magazine. Open the cover of magazine and load G&G.9mm BB pellets into the magazine. Insert the front sight adjustment tool into the front sight block. Turn for adjustment. Clockwise: Lower the front sight. Counterclockwise: Raise the front sight. Press the button and slide forward or backward for adjustment. For All RK Series Front Sight Adjustment For GK99 Rear Sight Adjustment For GK99 After the BB pellet had been loaded, close the cover and turn the gear on the bottom of the magazine until it clicks. Set the magazine upward. Connect firmly till a click sound is heard. Use the screwdriver to adjust the front sight windage. Flip-Up night front sight. Common shooting. Precision shooting.
Hop-Up / Motor Gear Adjustment For All RK Series Do not to catch your fingers in the dummy bolt. For All RK Series Adjust here only when the gear noise become shrilly. FoLding Stock For AIMS For AKMS For GK99 PRESS HOLD PULL Pull the handle in the direction shown to open the bolt. Sliding the Hop-up adjustment piece forward or backward to adjust the Hop-up effect. Unscrew the fixing screw on the bottom of the grip and remove the grip. Push the stock lock button to unlock. Push the stock lock button to unlock. Press and pull the stock to unlock. Never hold the gun sideways as the BB pellets will curve right or left. Too much HOP-UP. (Return the lever toward NORMAL) Best direction. Not enough HOP-UP.(Move the lever toward HOP) Or too much HOP-UP.(Return the lever toward NORMAL) Adjust with hexagon key. Turn the folding stock to be locked. Turn the folding stock to be locked. Turn the folding stock to be locked.
Maintenance.After Operation Remove the magazine, direct the muzzle into a safe direction then fire the gun in semi-auto mode for a few shots. Set the selector to the safe position. Always disconnect the battery and attach the protective cap whenever you do not operate the air gun..cautions on Motor and Battery Charge the battery if the firing cycle becomes slow. Pausing using the air gun for to minutes after firing about 00 rounds, in order to ensure long service lives of the motor and battery..when Pellets Are Clogged If pellets are clogged, remove then and apply a few drops of G&G silicone oil into the chamber from the magazine entrance. Apply G&G silicone oil for 0. to sec, to obtain smooth continuous firing. WHEN PELLET SPEED BECOMES LOW.Drop a few drops of silicone oil or Teflon oil from the pellet entrance. After inserting BB pellets into the magazine and fire pellets around to 00 or 00 pellets..to complete the cleaning, use the cleaning rod (with cotton), to remove excess oil. Make sure no dirt gets into the chamber to avoid clogging of pellets. The hopping up operation may be unstable for the first 00 to 00 rounds after using silicone oil, this is the normal operation fo the gun. REMOVING CLOGGED PELLETS Never use CRC-, WD0 or other corrosive lubricant..return the hop up dial to the Normal position and insert the cleaning rod from the lead edge of the barrel..to remove clogged BB s, carefully insert the cleaning rod inside the barrel with the flat tip facing down as shown below. Do not jam the cleaning rod into the barrel by force. Should the BB s remains inside the barrel after following the instruction above, with the protection cap over the barrel, point the gun to a safe direction and discharge any loosened BB s in semi-automatic mode. Trouble Shooting SYMPTOM POTENTIAL CORRECTIVE No operation at all Although motor is revolving, no pellet can be fired Impossible full-auto operation(automatic firing) Shooting distance becomes shorter Too loud operating noise Pellets being fallen out from barrel end If gun gets wet Disclaimer Accessories pictured are not always included with product. Adult supervision required for users under years of age. The purchaser and user should conform to all laws governing and ownership of airsoft guns. Selector lever is set to safety. Battery is not charged. Battery connector is disconnected. The and of battery connector is reverse. Expired motor life (0,000 to 0,000 rounds) or poor electrical connection. Pellets are clogged inside the magazine. Pellets are clogged in the chamber. Faulty gear. Insufficient battery power. Faulty pellet feed of magazine. Poor electrical connection. Damaged or worn chamber set. Damaged or worn piston set (O-ring,piston spring) Something is jammed in the inner barrel Faulty BB pellets (too small or heavy) Shrotage of silicone oil Gear problem caused by too many blank firing Worn or damaged gear Gear problem caused by too many blank firing Damaged or worn chamber set. No hop setting. Faulty BB Pellets (too small or heavy) Set the selector lever to Semi or Full Auto. Charge the battery. Connect the connector. Connect the connector correctly(check the fuse) Replace the dead motor (can be purchased from local dealer or directly G&G). Check and repair the contacts. Insert the charging rod into the magazine and move up and down a few times to remove clogged pellets. Remove clogged pellets using the cleaning rod. Pruchase the replacement gear from your dealer or G&G and repair. Charge the battery. Repair clogging of the magazine. Consult your dealer or us for overhaul maintenance or repair. Replace the replacement parts(purchasing from your dealer or G&G) Use the cleaning rod and clean the inner barrel. Use the genuine G&G Pellets. Drops few drops of silicone oil from upper the chamber. Consult your dealer or G&G for overhaul maintenance, part replacement (gear,etc.) or repair. Turn the hop adjustment lever toward Hop. When a problem occasion please check the steps below, other problems please turn to your dealer or contact us. Use the G&G Pellets. Stop operation immediately, disconnect the battery, wipe off water from inside the main body and the battery. After completely dry, carry out trial firing. If the unit is not operational, please contact your local dealer for repair. All products in this manual are imitation firearms and are not intended nor represented to be comparable in design, appearance, or function to any actural firearm offered by other manufacturers. Product names are trademarks of G&G, which has no affiliation to, and is not associated, or sponsored by any manufacturer of actual or imitation firearms. Products may vary form those pictured.
for RK RK - 0 RK - 00 You may buy all groups parts from G&G Support Dept. Email: support@guay.com RK - 00 RK - 00 RK - 0 RK - 00 9 RK - 0 RK - 0 RK - 00 RK - 0 RK - 00 RK - 09 RK - 00 RK - 0 RK - 00 For more product information. Please visit our website WWW.GUAY.COM RK - 0 RK - 009 9 RK - 0 RK - 0 RK - 0 RK - 0 RK - 00 for RK RK-00 RK-00 RK-00 RK-00 RK-00 RK-00 RK-00 RK-00 RK-009 RK-0 RK-0 RK-0 RK-0 RK-0 RK-0 RK-0 RK-0 RK-0 RK-09 RK-00 RK-0 RK-0 Receiver Cover Set Rear Sight Set Bolt Set Gas Block Set Rail Mount Set Receiver Set Barrel Base Set Gas Cylinder Set Outer Barrel Set Front Sight Set Butt Stock Set Selector Lever Set Gear Box Set Hop Up Set Inner Barrel Grip Set Motor Base Set Motor Set Handguard Set Trigger Guard Set You may buy all groups parts from G&G Support Dept. Email: support@guay.com
for RK / RK RK-0 9 RK-00 RK-00 RK-0 RK-00 RK-0 RK-00 RK-0 RK-0 RK-00 You may buy all groups parts from G&G Support Dept. Email: support@guay.com RK-0 RK-09 RK-00 RK-0 RK-00 RK-00 RK-00 RK-0 RK-009 9 RK-0 RK-0 RK - 0 RK - 009 RK - 0 RK-0 RK - 00 RK - 0 for RK / RK RK-00 RK-00 RK-00 RK-00 RK-00 RK-00 RK-0 RK-0 RK-0 RK-0 RK-0 RK-0 RK-09 RK-00 RK-0 RK-0 for RK RK-00 RK-00 RK-009 RK-0 RK-0 RK-0 for RK RK-00 RK-009 RK-0 RK-0 RK-0 Receiver Cover Set Rear Sight Set Bolt Set Receiver Set Barrel Base Set Gas Cylinder Set Butt Stock Set Selector Lever Set Gear Box Set Hop Up Set Grip Set Motor Base Set Motor Set Handguard Set Trigger Guard Set Gas Block Set Flash Suppressor Set Outer Barrel Set Front Sight Set Inner Barrel Flash Suppressor Set Outer Barrel Set Front Sight Set Inner Barrel
for RK EVO / RK EVO RK-0 9 RK-00 RK-00 RK-0 RK-00 RK-0 RK-00 RK-0 RK-0 RK-00 You may buy all groups parts from G&G Support Dept. Email: support@guay.com RK-0 RK-09 RK-00 RK-0 RK-00 RK-00 RK-00 RK-0 RK-009 9 RK-0 RK-0 RK - 0 RK - 009 RK - 0 RK-0 RK - 00 RK - 0 for RK EVO / RK EVO RKE-00 Receiver Cover Set RKE-00 Rear Sight Set RKE-00 Bolt Set RKE-00 Receiver Set RKE-00 Barrel Base Set RKE-00 Gas Cylinder Set RKE-0 Butt Stock Set RKE-0 Selector Lever Set RKE-0 Gear Box Set RKE-0 Hop Up Set RKE-0 Grip Set RKE-0 Motor Base Set RKE-09 Motor Set RKE-00 Handguard Set RKE-0 Trigger Guard Set RKE-0 for RK EVO RKE-00 RKE-00 RKE-009 RKE-0 RKE-0 RKE-0 for RK EVO RKE-00 RKE-009 RKE-0 RKE-0 RKE-0 Gas Block Set Flash Suppressor Set Outer Barrel Set Front Sight Set Inner Barrel Flash Suppressor Set Outer Barrel Set Front Sight Set Inner Barrel
for RK BETA RKBETA-009 RKBETA-00 You may buy all groups parts from G&G Support Dept. Email: support@guay.com RKBETA-00 RKBETA-0 9 RKBETA-0 RKBETA-0 RKBETA-00 RKBETA-00 RKBETA-09 RKBETA-0 RKBETA-00 RKBETA-0 RKBETA-00 RKBETA-00 RKBETA-00 9 RKBETA-0 RKBETA-0 RKBETA-0 RKBETA-0 9 for RK BETA RKBETA-00 RKBETA-00 RKBETA-00 RKBETA-00 RKBETA-00 RKBETA-00 RKBETA-00 RKBETA-00 RKBETA-009 RKBETA-0 RKBETA-0 RKBETA-0 RKBETA-0 RKBETA-0 RKBETA-0 RKBETA-0 RKBETA-0 RKBETA-0 RKBETA-09 Receiver Cover Set Bolt Set Flash Suppressor Receiver Set Barrel Base Set Gas Cylinder Set Front Sight Set Butt Stock Set Selector Lever Set Gear Box Set Hop Up Set Outer Barrel Inner Barrel Grip Set Motor Base Set Motor Set Rail Handgurad Set Trigger Guard Set You may buy all groups parts from G&G Support Dept. Email: support@guay.com
for GK99 BlowBack Ver. GK99BB-0 GK99BB-00 GK99BB-00 GK99BB-00 You may buy all groups parts from G&G Support Dept. Email: support@guay.com GK99BB-0 GK99BB-0 GK99BB-0 GK99BB-0 GK99BB-0 GK99BB-0 9 All AEG products 0% Made in Taiwan GK99BB-00 GK99BB-00 GK99BB-00 For more product information. Please visit our website WWW.GUAY.COM 9 GK99BB-00 GK99BB-00 GK99BB-0 GK99BB-0 GK99BB-00 GK99BB-09 GK99BB-009 for GK99 BlowBack Ver. GK99BB-00 GK99BB-00 GK99BB-00 GK99BB-00 GK99BB-00 GK99BB-00 GK99BB-00 GK99BB-00 GK99BB-009 GK99BB-0 GK99BB-0 GK99BB-0 GK99BB-0 GK99BB-0 GK99BB-0 GK99BB-0 GK99BB-0 GK99BB-0 GK99BB-09 GK99BB-00 Receiver Cover Set Bolt Lever Set Bolt Guide Set Gas Tube Receiver Set Handguard Set Gas Block Set Front Sight Set Flash Suppressor Folding Stock Set Grip Selector Lever Set Gear Box Set Hop Up Set Outer Barrel Set Inner Barrel Motor Base Set Motor Set Trigger Guard Set You may buy all groups parts from G&G Support Dept. Email: support@guay.com