Electronic Drivetrain Cabling Guide R1.0

Electronic Drivetrain Cabling Guide R1.0

Congratulations on the purchase of your new PARLEE Altum! The Altum is our most advanced model to date, delivering race ready performance with our signature PARLEE ride. This manual contains important assembly and service information. All assembly and service of PARLEE bicycles must be carried out by an authorized PARLEE Dealer/Mechanic. Note to PARLEE Dealers/Mechanics: We strongly advise that you read this manual in its entirety before assembly of the bicycle to familiarize yourself with the systems and proprietary procedures of its assembly. If you have any questions contact PARLEE at: Phone: 978.998.4880 Email: Info@parleecycles.com 1

Table Of Contents 03 - Seat Post Installation 08 - Frame Set Assembly 11 - Brake Cable Housing Installation 18 - Head Tube Assembly 20 - Electronic Housing Installation 26 - Final Cable Routing Overview 27 - Frame Armor Installation 2

Altum Clamp Follower Seat Post Clamp Nut Seat Post Assembly Altum Clamp Top M5 Wedge Clamp Bolt 3

Red Loctite All Threaded Surfaces. Torque to 5-8nm 1 Seat Post Clamp 4

2 Tape Battery Foam Padding Insert battery electronic wire into seattube and guide towards the bottom bracket. Battery Electronic Wire 5

3 Battery Foam Padding Tape Battery Electronic Wire 6

4 Seat Post Apply Carbon Paste 7

Lower Bearing Upper Bearing Frame Set Assembly Top Cap 15mm Bearing Seal Bearing Ring 8

Blind Grommet Steel Spacer x2 For Mechanical Front Drive - train Teflon Tubing Electronic BB Hatch For Mechanical Drive - train For Electronic Drive - train Foam Silencer Tubing Brake Housing Stop Rubber Seal 9

BB Cable Guide Electronic DT Cable Stop Electronic Drive - Trains Only Electronic Rear Derailleur Grommet Electronic Drive - Trains Only Mechanical Rear Derailleur Grommet Mechanical Drive - Trains Only Mechanical DT Cable Stop Electronic Drive - Trains Only 10

5 Rear Brake Housing 11

6 Rear Brake Housing 12

7 Foam Silencer Tubing Rear Brake Housing 13

8 Foam Silencer Tubing Rear Brake Housing 14

9 Foam Silencer Tubing Rear Brake Housing 15

10 Foam Silencer Tubing Rear Brake Housing 16

11 Foam Silencer Tubing Rear Brake Hosuing 17

Flex Fit Cap Assembly 12 Rubber Seal 18

Flex Fit Cap 13 Bearing Seal Spacer Apply Grease Center Ring Upper Bearing Lower Bearing Apply Grease 19

14 Use Manufacturers Supplied Grommet Downtube Electronic Wire: 1,000 mm 20

15 Rear Derailleur Electronic Wire: 650 mm 21

16 Rear Derailleur Electronic Wire: 650 mm 22

17 Use Drive - Train Manufacturers Supplied Grommet Seattube Battery Electronic Wire: 650 mm Downtube Electronic Wire: 1000 mm Front Derailleur Electronic Wire: 300/400 mm Rear Derailleur Electronic Wire: 650 mm 23

18 Wrap the electronic junction box in foam and insert into bottom bracket. Seattube Battery Electronic Wire: 650 mm Downtube Electronic Wire: 1000 mm Front Derailleur Electronic Wire: 300/400 mm Rear Derailleur Electronic Wire: 650 mm 24

19 Seattube Battery Electronic Wire: 650 mm Downtube Electronic Wire: 1000 mm Front Derailleur Electronic Wire: 300/400 mm Rear Derailleur Electronic Wire: 650 mm 25

20 Seattube Battery Electronic Wire: 650 mm Downtube Electronic Wire: 1000 mm Front Derailleur Electronic Wire: 300/400 mm Rear Derailleur Electronic Wire: 650 mm 26

Frame Armor Installation HT Cable Guard Chain Suck Guard Chain Slap Guard Clean Surface Use de - natured alcohol and lint free to clean surface Instructions Apply pressure from center outward. Use hair dryer to remove guards 27