Form -0 R September 0 Parts & Installation Instructions SV & SV.,. &. and SVLD. Snow Plow Item Part No. Part No. Part No. Part No. Part No. Part No. Qty. Description SVLD. SV. SV. SV. SV. SV. Moldboard Assembly 0 0 044 0 044 0 R.H. & L.H. Wing 0 00 044 0 0444 00 R.H. Wing 0 00 044 0 044 0 L.H. Wing 0 40 4 Trip Edge Weld/ Holes --------- 4 4 4 40 4 Trip Edge Weld/ Holes 4 4 4 4 4 4 4 X -/ Pin 040 040 040 040 040 040 /4 x Cotter Pin 4 4 T -Bar Weldment 0 0 0 0 0 4 Trip Spring 04 04 04 04 04 04 Bolt H /- x Gr. 0 0 0 0 0 0 Locknut /- 0 0 0 0 0 0 4 Flatwasher / 04 04 04 04 04 04 4 Eyebolt w/locknuts and Cap 0 0 0 0 0 0 Cutting Edge Kit / Bolt 0 0 0 0 0 0 Cutting Edge 0 0 0 0 0 0 Hardware Bag 0 0 0 0 0 0 Locknut /- 4 Bolt C /- x 0 0 0 0 0 0 Bolt C /- x -/4 Gr. 0 0 0 0 0 0 Bottom Belt Kit / Bolt ** Bottom Belt 0 0 0 0 0 0 Hardware Bag * 4 4 4 4 4 Backing Plate * 0 0 0 0 0 0 Locknut /- * 0 0 0 0 0 0 Bolt C /- x -/4 Gr. --------- 04 04 04 04 04 Cutting Edge Kit / Bolt --------- 044 044 04 04 04 Cutting Edge --------- 04 04 04 04 04 Hardware Bag --------- 0 0 0 0 0 4 Locknut /- 4 --------- 0000 0000 0000 0000 0000 4 Bolt C /- x --------- 040 040 040 040 040 Bottom Belt Kit / Bolt --------- 040 040 040 040 040 Bottom Belt Kit / Bolt ** --------- 404 404 404 404 404 Bottom Belt --------- 04 04 04 04 04 Hardware Bag * --------- 40 40 40 40 40 Backing Plate * --------- 0 0 0 0 0 Locknut /- * --------- Bolt C /- x -/4 Gr. 044 0 0 0 0 0 Hardware Carton ** Pivot Pin * 0 00 00 00 00 00 00 Bolt H /- x -/ Gr. * 0 0 0 0 0 0 Lockwasher / ** 0 0 0 0 0 0 Plow Marker Kit 00 000 000 000 000 000 Plow Marker 4 4 4 4 4 4 4 Locknut /4-0 SS 4 0 0 0 0 0 0 4 Bolt H /4-0 x SS 0 0 0 0 0 0 Top Deflector Kit ** Top Deflector 04 04 04 04 04 04 Hardware Bag * 4 4 4 4 4 4 Deflector Brace * 00 00 00 00 00 00 Bolt H /- x -/4 Gr. * 0 0 0 0 0 0 Flatwasher / * 04 04 04 04 04 04 Locknut /- A-Frame Parts indented are included in the carton, bag or assembly under which they are indented. * (SV & SV ) Items in 00 Hardware Bag included in 0 * (SVLD) Items in 00 Hardware Bag included in 044 * * (SV & SV ) Items packed in the 0 Hardware Carton * * (SVLD) Items packed in the 044 Hardware Carton
SUPER V OPTIONAL MUSHROOM RUNNERS - FIGURE Item Part No. Qty Description 04 Super-V Mushroom Runner Kit 4 Mushroom Shoe Casting Assy. 44 Runner Spacer 0 Runner Washer 4 0 Linch Pin 4 Runner Bracket Assy. 0 Hardware Bag 04 4 Bolt H /- x Gr. 0 4 Locknut /- Reference Form -4 for Installation Instructions REMOVE SET SCREW 0 4 4 4 4 Figure SUPER V 4 REMOVE SET SCREW 0 4 4 4 Figure
INSTALLATION INSTRUCTIONS:. Position wing assemblies & face down on cardboard as not to damage the painted surfaces. Grease the bushings on both left and right wings. Position the wings so pivot bushings align. Note: Cutting Edges will be inline at this time.. Remove /"- x set screw located in top of A-Frame () tower. Grease A-Frame () bushings and Pivot Pin (). With a helper, lift the A-Frame () and insert its bushings in alignment with the wing bushings.. Insert Pivot Pin () through bushings. Install and tighten /" x.0" bolt (0) and /" lockwasher () to top of A-Frame holding Pivot Pin () in place. Note: Wipe off any excess grease at this time. 4. Using the A-Frame as leverage tilt the moldboard assembly raising the Cutting Edges off the ground. Support Cutting Edges () to inches off the ground.. Install the Bottom Belt () to left and right wing at Tripedge () using /" x." carriage bolt () and locknut (). Note: Be sure that Belt () folds are upward and notches are toward the A-Frame (). Assemble Backing Plate () so bent end is facing the cutting edge forcing the belt against the Tripedge (). See Figure.. Using the A-Frame as leverage tilt the moldboard assembly raising the Cutting Edges off the supports. Remove supports and set moldboard assembly to the upright position.. Assemble Snow Deflector Brace () to Pivot Pin (). Place brace under the pivot pin plate. Attach using two /" x -/4" bolts (), / washers () and / locknuts ().. Position moldboard assembly in the Vee position.. Assemble Top Snow Deflector () positioning the deflector under deflector brace (). Attach deflector ends under left and right wing gussets using /" x -/4" bolts (), / locknuts () and / washers (). Tighten locknuts such that washers slightly compress the rubber surface. Note: Snow Deflector Belt should fold/loop downward between brace and each wing gusset when wings are not in the Vee position. See Hydraulic Instructions (Form -) for assembly of Wing Cylinders. CAUTION: CHECK THE TRIPEDGE ADJUSTMENT AT THIS TIME. A. THE SPRINGS ARE PROPERLY ADJUSTED WHEN A PIECE OF PAPER CAN BE PLACED BETWEEN EACH COIL. B. IF THE TRIPEDGE SPRINGS NEED ADJUSTMENT, LOOSEN THE BOTTOM NUT (A) ON BOTH SPRING ASSEMBLIES. ROTATE THE TOP LOCKNUT NUT (B) UNTIL THE SPRINGS ARE PROPERLY ADJUSTED. C. BE SURE TO TIGHTEN THE BOTTOM NUT (A) SECURELY ON BOTH ASSEMBLIES TO PREVENT LOOSENING OF THE ASSEMBLIES. B A Spring Assembly Meyer Products LLC reserves the right, under its continuing product improvement program, to change construction or design details, specifications and prices without notice or without incurring any obligation.
Parts & Installation Instructions Stainless Steel SV.,. &. Item Part No. Part No. Part No. Qty. Description SV. SV. SV. Moldboard Assembly 044 04 04 R.H. & L.H. Wing 04 040 04 SS R.H. Wing 04 04 04 SS L.H. Wing 40 40 4 RH Moldboard Weld 40 40 4 LH Moldboard Weld 40 40 4 RH Stainless Steel Sheet 4 400 404 4 LH Stainless Steel Sheet 40 4 40 Bottom Mount Plate 4 40 4 Trip Edge Weld 0 0 0 Locknut /- 0 0 0 Locknut /- Flatwasher SAE 4 4 4 Bolt C /- x -/4 4 4 4 X -/ Pin 4 4 4 Roll Pin / x. 4 4 T -Bar Weldment 4 0 0 0 4 Trip Spring 04 04 04 Bolt H /- x Gr. 0 0 0 Locknut /- 0 0 0 4 Flatwasher / 04 04 04 4 Eyebolt w/locknuts and Cap 04 04 04 Cutting Edge Kit 044 04 04 Cutting Edge 04 04 04 Hardware Bag 0 0 0 0 4 Locknut /- 0000 0000 0000 4 Bolt C /- x 040 040 040 Bottom Belt Kit 040 040 040 Bottom Belt Kit ** 404 404 404 Bottom Belt 04 04 04 Hardware Bag * 4 40 40 40 Backing Plate * 0 0 0 Locknut /- * Bolt C /- x -/4 Gr. 0 0 0 Hardware Carton ** Pivot Pin * 00 00 00 Bolt H /- x -/ Gr. * 0 0 0 Lockwasher / ** 0 0 0 Plow Marker Kit 000 000 000 Plow Marker 4 4 4 4 Locknut /4-0 SS 0 0 0 4 Bolt H /4-0 x SS 0 0 0 Top Deflector Kit ** Top Deflector 04 04 04 Hardware Bag * 4 4 4 4 Deflector Brace * 00 00 00 Bolt H /- x -/4 Gr. * 0 0 0 Flatwasher / * 04 04 04 Locknut /- A-Frame Parts indented are included in the carton, bag or assembly under which they are indented. * (SV ) Items in 00 Hardware Bag included in 0 ** (SV ) Items packed in the 0 Hardware Carton
STAINLESS STEEL SUPER V 4 4 Figure 4 4 & 0 OPTIONAL MUSHROOM RUNNERS - FIGURE Item Part No. Qty Description 04 Super-V Mushroom Runner Kit 4 Mushroom Shoe Casting Assy. 44 Runner Spacer 0 Runner Washer 4 0 Linch Pin 4 Runner Bracket Assy. 0 Hardware Bag 04 4 Bolt H /- x Gr. 0 4 Locknut /- Reference Form -4 for Installation Instructions 4 Figure
STAINLESS STEEL SV INSTALLATION INSTRUCTIONS:. Position wing assemblies & face down on cardboard as not to damage the painted surfaces. Grease the bushings on both left and right wings. Position the wings so pivot bushings align. Note: Cutting Edges will be inline at this time.. Remove /"- x set screw located in top of A-Frame () tower. Grease A-Frame () bushings and Pivot Pin (). With a helper, lift the A-Frame () and insert its bushings in alignment with the wing bushings.. Insert Pivot Pin () through bushings. Install and tighten /" x.0" bolt () and /" lockwasher () to top of A-Frame holding Pivot Pin () in place. Note: Wipe off any excess grease at this time. 4. Using the A-Frame as leverage tilt the moldboard assembly raising the Cutting Edges off the ground. Support Cutting Edges () to inches off the ground.. Install the Bottom Belt () to left and right wing at Tripedge () using /" x." carriage bolt () and locknut (). Note: Be sure that Belt () folds are upward and notches are toward the A-Frame (). Assemble Backing Plate (4) so bent end is facing the cutting edge forcing the belt against the Tripedge ).. Using the A-Frame as leverage tilt the moldboard assembly raising the Cutting Edges off the supports. Remove supports and set moldboard assembly to the upright position.. Assemble Snow Deflector Brace (4) to Pivot Pin (). Place brace under the pivot pin plate. Attach using two /" x -/4" bolts (), / washers () and / locknuts ().. Position moldboard assembly in the Vee position.. Assemble Top Snow Deflector () positioning the deflector under deflector brace (4). Attach deflector ends under left and right wing gussets using /" x -/4" bolts (), / locknuts () and / washers (). Tighten locknuts such that washers slightly compress the rubber surface. Note: Snow Deflector Belt should fold/loop downward between brace and each wing gusset when wings are not in the Vee position. See Hydraulic Instructions (Form -) for assembly of Wing Cylinders. CAUTION: CHECK THE TRIPEDGE ADJUSTMENT AT THIS TIME. A. THE SPRINGS ARE PROPERLY ADJUSTED WHEN A PIECE OF PAPER CAN BE PLACED BETWEEN EACH COIL. B. IF THE TRIPEDGE SPRINGS NEED ADJUSTMENT, LOOSEN THE BOTTOM NUT (A) ON BOTH SPRING ASSEMBLIES. ROTATE THE TOP LOCKNUT NUT (B) UNTIL THE SPRINGS ARE PROPERLY ADJUSTED. C. BE SURE TO TIGHTEN THE BOTTOM NUT (A) SECURELY ON BOTH ASSEMBLIES TO PREVENT LOOSENING OF THE ASSEMBLIES. B A Spring Assembly Meyer Products LLC reserves the right, under its continuing product improvement program, to change construction or design details, specifications and prices without notice or without incurring any obligation. 0 Printed in the U.S.A. Meyer Products LLC Euclid Ave. Cleveland, Ohio 44-4 Phone () 4- www.meyerproducts.com email info@meyerproducts.com