parts guide
Bolt OM7010 Bolt Tail O-rings XTC309 Bolt Only lubricate with GR33SE TM paintball marker lubricant. enmey Body Assembly OM7017 Rear Breech O-ring OB7017 SFT O-ring Lightly grease O-ring Grease Entire O-ring OH7M06 Large Bolt O-ring OM7015 Bolt Bumper O-ring Grease entire O-Rings Lightly grease entire surface Bolt Sleeve OB7022 Bolt Sleeve Friction O-ring Bolt Stop OB7018 Bolt Stop Outer O-ring Grease entire O-Rings XTC104 Bolt Sleeve OB7018 Bolt Sleeve O-rings (2x) DO NOT GREASE XTC110 Bolt Stop Grease entire O-Rings OM7014 Bolt Stop Inner O-ring GUIDE Rev 1.3 Page 2
NUT003 Neck Clamp Nuts ENV111 Ball Detent OM7006 (INSIDE SLOT) SSC007 Neck Clamp Screws ENV111 Ball Detent ENV115 Clamping Feedneck NME101 enmey Body Cover GUIDE Rev 1.3 Page 3
nmk1 Trigger Valve OB7008 nmk2 Trigger Valve nmk2 Trigger Valve HNY175 OB7008 The nmk2 Trigger Valve may be identified by its lower profile, downward facing screw heads (when mounted in the enmey) and metal pressure plate. Correct valve identification is critical to trigger actuator selection (see page 8). ENV123 OB7M04 ENV122 ENV113 OB7M05 HOS001 NOTE: Pneumatics hoses are single-use parts. Once removed from a barbed fitting, they will have been stretched to the point that they can no longer provide a reliable seal. NME121 OB7M04 ENV122 Sealed to ASA with thread-locking compound GUIDE Rev 1.3 Page 4
SSF006 Rear Vertical Adaptor Screw ENV112 Vertical Adatptor Rear SSF006 Top Vertical Adapter Screw GUIDE Rev 1.3 Page 5
Vertical Regulator OM7014 Piston O-ring OB9015 Regulator ASA O-ring VRG105 Piston XTC105 Vertical Regulator Body VRG106 Piston Seat SPR32 Main Regulator Spring OM7010 Inner Spring Platform O-ring OB7014 Outer Spring Platform O-ring VRG102 Spring Platform OM7006 Relief Valve Seal VRG109 Relief Valve Washer VRG108 Relief Valve Body OB7010 Relief Valve Body O-ring VRG107 Relief Valve Piston OU9006 Adjuster Screw O-ring FLT002 - Regulator Inlet Filter OM9006 Adjuster Screw O-ring VRG104 Adjustment Screw VRG102 Spring Platform SPR033 Relief Valve Spring GUIDE Rev 1.3 Page 6
FLT001 Filter Screen Vertical Regulator GUIDE Rev 1.3 Page 7
NME106 Grip Frame NME204 Actuator Pin BAL001 Safety detent SPR007 Safety detent spring OBM04 NUT002 Grip Nut nmk1 - NME104 Actuator Pin nmk2 - NME204 Actuator Pin NUT002 Grip Nut NME108 enmey Safety 4mm x 1mm Red Silicone Safety O-ring IMPORTANT: The nmk2 Actuator Pin must only be used with the nmk2 Trigger Valve (see page 4) or valve damage will result. An nmk1 Actuator Pin will not work with an nmk2 Trigger Valve. The nmk2 Actuator Pin may be identified by the X-shaped wings in its middle. GUIDE Rev 1.3 Page 8
NME107 enmey Trigger PIN018 Trigger Pin SPR008 Trigger Return Spring NOTE: Use a lower hole to increase trigger resistance, higher to decrease. Factory default position is second from the top for a light, yet reliable trigger pull. GUIDE Rev 1.3 Page 9
ENV136 Bottom-line ASA OM9014 Regulator Swivel O-ring Seal threads with PTFE tape or thread locking compound. Grease entire O-ring. HBR476 Braided Hose Seal threads with PTFE tape or thread locking compound. VRG103 Regulator Swivel Grease entire O-ring. OM9014 Regulator Swivel O-ring Note: The threaded hose fitting must not protrude into the center of the regulator swivel. When tightening hose fittings, be certain that ASA mount holes and hole in center of swivel are aligned. GUIDE Rev 1.3 Page 10
NUT004 Bottom-line nuts SSB002 10-32 Bottom-line screws GUIDE Rev 1.3 Page 11
SSB009 Grip Screw NME116 enmey Grip SSB009 Grip Screw SSB009 Grip Screw SSB009 Grip Screw GUIDE Rev 1.3 Page 12
SSB003 Grip Frame Screw SSB003 Grip Frame Screw CLP006 GUIDE Rev 1.3 Page 13
GUIDE Rev 1.3 Page 14