TANDEM plus 569F/569A installation instructions inside Heavy duty full extension concealed runners Basic components Locking devices Runners New side adjustment New rear side adjustment Rotate side adjustment left or right equally After front side adjustment is made with the on both locking devices. Drawer front moves in the same direction as rotation. locking devices, rotate the rear side adjustment left or right to re-align the back of the box with the front. Drawer back moves in the same direction as rotation. 0 Height adjustment Press up on adjustment tab Push towards back of Tilt adjustment Rotate the tilt adjustment lever on the rear of each runner to lift the back of the and tilt the top of the front forward. front R L R L Maximum (/8") rise of front (tool-free) Maximum 5 (/6") rise of back (tool-free) NOTE: Height and tilt adjustments available with all combinations of locking devices and runners 0 L R New depth adjustable locking device Locking device T5.90.PS with side, height and depth adjustment Depth adjustment on runner TANDEM 569 runners feature elongated holes that allow ±4.5 (/6") depth adjustment L R Maximum.5 (/6") to left or right on both front and rear (tool-free) NOTE: Side adjustment not available on T5.x8xx locking devices Turning the adjustment screw allows for up to a +.5 (") out adjustment NOTE: For T5.90.PS setback in inset applications, see page 5 Dimensions in millimeters (inch equivalents as noted) 0 Blum, Inc.
Drawer specifications Face frame and panel applications Preparing for hardware installation Front view opening width inside width = opening width minus 49 6 (/4") minimum top clearance Installation screw 606N or 606P 75 Locking device T5.90 with side adjustment or T5.80 without side adjustment pre-boring holes for locking devices #6 head wood or system screws 7 (-5") 4.5 (") side maximum 9 (/4") (/") height maximum = opening minus 0 (5") opening height pre-boring holes for rear hooks.5 mm bit with extension chuck 4 (9/6") bottom clearance 6 mm bit with stop collar TANDEM template T65.600.0 NOTE: Because material may vary, the inside width must equal opening width minus 49 for TANDEM to align and function properly NOTE: Use of the T65.600.0 TANDEM template is essential for accurate location and angle of pre-bored locking device holes and accurate boring for rear hook holes Drawer insertion Extend the runners fully. Place the on the runners and close. The locking devices automatically engage with the runners. Make adjustments if necessary. Drawer removal Squeeze orange handles on locking devices Pull straight out and up Dimensions in millimeters (inch equivalents as noted) 0 Blum, Inc.
Face frame application Runner mounting specifications 786 (0-5/6") minimum face Cabinet and specifications depth inside depth 88 (") 76 (0") mounting position 0 (") 8 (/4") typical setback (/8") 709 (7-9") minimum 569A760B 76 (0") 569A6860B 686 (7") blocking behind frame runner setback (/8") Target Drawer Length face mounting position 0 (") 7 (-5") 5 (") minimum top clearance 6 (/4") maximum height = opening minus 0 (5") gap.5 (/6") bottom clearance 4 (9/6") 686 (7") 64 (4-") minimum 569A600B 60 (4") blocking behind frame bottom recess (/") 60 (4") 557 (-5/6") minimum 569F50B 5 (") TANDEM plus depth inside depth minimum 569A760B 88 (") 786 (0-5/6") 76 (0") maximum runner 777 (0-9") 569A6860B 76 (0") 709 (7-9") 686 (7") 700 (7-9/6") 569A600B 686 (7") 64 (4-") 60 (4") 9 (/4") 65 (4-9") detail of front holes 5 (") 480 (8-9") minimum 569F4570B 457 (8") 569F50B 60 (4") 557 (-5/6") 5 (") 548 (-9/6") 569F4570B 5 (") 480 (8-9") 457 (8") 47 (8-7") NOTE: For heavy duty applications, rear brackets and sockets cannot be used. Cabinet sides must be blocked-out flush with the inside of the frame. (-/4") 4 (-") 9 (") typical 7 (9") 7 (-5") 5 (") NOTE: Orange dots indicate screw locations required to meet specified load capacities T5.90R T5.90L T5.80R T5.80L 606N or 606P 66.50.HG Locking device with side adjustment (right) Locking device with side adjustment (left) Locking device (right) Locking device (left) #6 Wood screw (for mounting runner to side, rear brackets and locking devices) #6 System screw (for mounting runner to side) Dimensions in millimeters (inch equivalents as noted) 0 Blum, Inc.
Panel application Runner mounting specifications Cabinet and specifications mounting position 7 (-5") face depth 8 (5-") 4 (8-/6") inside depth 88 (") 8 (/4") typical setback (/8") 569A760B 76 (0") runner face 786 (0-5/6") minimum mounting position 7 (-5") 7 (-5") 76 (0") 8 (5-") 709 (7-9") minimum 4 (8-/6") 569A6860B 686 (7") setback (/8") 5 (") minimum top clearance 6 (/4") maximum height = opening minus 0 (5") 8 (5-") 4 (8-/6") gap.5 (/6") bottom clearance 4 (9/6") 686 (7") 64 (4-") minimum 569A600B 60 (4") 56 (0-") 4 (8-/6") bottom recess (/") 60 (4") detail of front holes (-/4") 4 (-") 5 (") 9 (") typical 7 (9") 5 (") 7 (-5") 557 (-5/6") minimum 9 (7-9/6") 480 (8-9") minimum 4 (8-/6") NOTE: Orange dots indicate screw locations required to meet specified load capacities 569F50B 5 (") 569F4570B 457 (8") TANDEM plus depth inside depth minimum 569A760B 88 (") 786 (0-5/6") 76 (0") maximum runner 777 (0-9") 569A6860B 76 (0") 709 (7-9") 686 (7") 700 (7-9/6") 569A600B 686 (7") 64 (4-") 60 (4") 9 (/4") 65 (4-9") 569F50B 60 (4") 557 (-5/6") 5 (") 548 (-9/6") 569F4570B 5 (") 480 (8-9") 457 (8") 47 (8-7") T5.90R T5.90L T5.80R T5.80L 606N or 606P 66.50.HG Locking device with side adjustment (right) Locking device with side adjustment (left) Locking device (right) Locking device (left) #6 Wood screw (for mounting runner to side, rear brackets and locking devices) #6 System screw (for mounting runner to side) 4 Dimensions in millimeters (inch equivalents as noted) 0 Blum, Inc.
Inset application Face frame application complete blockout (see table) Trial recommended Panel application (see table) Trial recommended blocking behind frame inside depth minimum = runner + setback + 6 (/4") inside depth range minimum = runner + setback + 6 (/4") Setback information Runner setback when using depth adjustable locking device (T5.90.PS) sub-front mounting hole position front NOTE: Runner cannot be mounted below opening 56/569 F/A sub-front (/") 7 (") 0 (5") (9") 6 (5/8") 0 (5") (9") 6 (-") 9 (/4") (9") 6 (-") 9 (-5") 6 (5/8") 9 (/4") (7/8") calculating Runner setback when using all other locking devices front Setbacks in this table recess the face of the front inside of the (") The depth adjustment can then be used to move the front out to its desired position,.5 (") out adjustment only 56/569 F/A sub-front + front minus (5") 56/569 F/A sub-front (/") 4.5 (9/6") 7.5 (/6") 0.5 (/6") 6 (5/8") 7.5 (/6") 0.5 (/6").5 (5/6") 9 (/4") 0.5 (/6").5 (5/6") 6.5 (-") 6 (5/8") 9 (/4") (7/8") front Setbacks in this table set the face of the front flush with the face of the If a depth adjustable locking device is needed, please see the locking device and table above NOTE: For mounting hole position add 7 (9") to calculating 56/569 F/A sub-front + front minus 4.5 (9/6") 5 Dimensions in millimeters (inch equivalents as noted) 0 Blum, Inc.
Attachment specifications Depth adjustment specifications B A 0.5 (/6") setback Mount each runner using at least two of the elongated holes. Install the to check the position of the front. Remove the, loosen screws and make adjustments if necessary, ±4.5 (/6"). Tighten the screws, verify the front position and finish mounting the runners using the screw locations indicated by the orange dots. TANDEM plus A 569A760B 44.5 (9-5/8") 7.5 (4-") 569A6860B 44.5 (9-5/8") 7.5 (4-") 569A600B 44.5 (9-5/8") 7.5 (4-") 569F50B 44.5 (9-5/8") 500.5 (9-") 569F4570B 44.5 (9-5/8") 46.5 (7-/6") B Millimeter to inch conversion chart.5 4 5 5.5 6 7 8 9 9.5 0.5 4 5 6 7 7.5 8 9 0 0.5 4 4.5 5.4 /6 /8 5 /6 7 /4 9 5 /6 /8 7 /6 5 / 7 9 /6 9 5 /8 /6 /4 5 /6 7 7 /8 9 5 /6 6 Dimensions in millimeters (inch equivalents as noted) 0 Blum, Inc. INST-TDM569F-569A 07.