Volume ooster Supply pressure Pressure range onnection Device Page max. bar bar thread precise differential pressure also 17 0 1 / 10 and G 3 8 R50.02 differential pressure also 10 0.2 1 / 8 ¼ NPT 53.19 53.24.03 transmission ratio 1:1 bis 1: 17 0 10 and G 3 8 R750.04 differential pressure also 1 0 10 - G½ R03-J.05 different transmission ratio 17 0 10 and G 3 8 R208.0 different transmission ratio, high-precision 17 0 10 G½ and G¾ R450.07 high exhaust capacity 17 0 10 G¾ - G1 R490.08 high flow rate 17 0 10 G1 and G1½ R200.09 high exhaust capacity 17 0 10 1½ NPT R201.09 high exhaust capacity 28 0.2 18 - G1¼ R11.10 standard high flow rate 21 0.2 18 - G3 R119-J.11 low pressure also for gases 20 10 350/1000 mbar G1 - G2 RZ-J.12 also for gases 0.4 2 55/ 10 mbar G½ - G2 RGDJ-J.13 also for gases 4 5 350 mbar G½ - G1½ RG4-J.13 high pressure transmission ratio 1:2 to 1:19 20 3 42 / 104 ½ NPT and ¾ NPT RH3-J.14 made of brass 50 1 15 / 50 - G2 R120-J.15 made of stainless steel 100 0 24 / 99 G1 RLE.1 made of brass 100 0 24 / 99 G1 RLM.1 Volume ooster.01
Positive ias Relay / Differential Pressure Regulator R50 Signal-operated regulator designed to provide pressure which is the sum of the input pressure plus a preset bias. s an option, the relay can start with bias range -0.3 bar / -4 psi. The relay can also be used as a differential pressure regulator. compressed air or non-corrosive gases Supply pressure max. 17 bar Pilot pressure max. 10 bar, ccuracy response sensitivity: < 1 mbar ir consumption without constant bleed Relieving function relieving Relief capacity 110 l/min at 1.5 bar and 0.35 bar overpressure above setpoint Gauge on both sides of the body, screw plugs supplied Mounting position any Temperature range 0 to 90 / 32 F to 194 F, for appropriately conditioned compressed air down to -40 / -40 F Material ody: aluminium die-cast Elastomer: NR/una-N Inner valve: brass and G 3 8, 1 300 l/min parallel translation Dimensions Flow onnection Supply Positive Pressure Order Price rate thread recommended bias range number D mm mm mm m ³ /h* 1 l/min* 1 G bar bar bar Positive bias relay R50 supply pressure max. 17 bar, relieving, without constant bleed, transmission 1:1 D 8 170 1 72 1 200 5 0 1 0 10 R50-02 230,00 5 0 2 R50-02D 230,00 8 0 4 R50-02E 230,00 15 0 10 R50-02F 230,00 8 170 1 78 1 300 G 3 8 5 0 1 0 10 R50-03 230,00 5 0 2 R50-03D 230,00 8 0 4 R50-03E 230,00 15 0 10 R50-03F 230,00 R50 ooster negative bias factory-set to -0.3 bar R50-0..Y NPT connection thread R50-0..N tapped exhaust connection thread G 1 8 R50-0..X12 tamper-proof cap above spindle, total height 174 mm R50-0..T ccessories pressure Ø 50 mm, 0 * 2 bar, M5002-..* 2 mounting bracket made of steel W00-33 gas 1 control booster differential pressure adjustment + 1 bar gas 2 Example 1: constant differential pressure of 1 bar at high flow Example 2: constant differential pressure of 1 bar 58 Ø9 18 45 R50 W00-33 * 1 at 7 bar supply pressure and bar pressure * 2 01 = 0...1 bar, 02 = 0 2.5 bar, 04 = 0 4 bar, 10 = 0 10 bar R50-02.02
Precision Volume ooster / Differential Pressure Regulator 53.19 53.24 The volume booster amplifies the volume at a 1:1 ratio of pressure to pressure. Manual setting through an adjusting screw or handwheel generates a shift of the pressure range between pressure and pressure. This bias is possible both positive and negative by 2 bar. dry, oil-free and 25 μm filtered compressed air Supply pressure max. 10 bar Pilot pressure max. 8 bar, G 1 8 ccuracy response sensitivity: < 1 mbar ir consumption max. 3 l/min, subject to pressure, 1% of volume flow Relieving function relieving, the exhaust valve's diameter is six times greater than the regulating valve s diameter Gauge ¼ NPT on both sides of the body, screw plugs supplied Mounting position any Temperature range 0 to 70 / 32 F to 158 F, for appropriately conditioned compressed air down to -30 / -22 F Material ody: zinc die-cast Elastomer: NR/una-N 1 4 NPT, 280 l/min parallel translation Dimensions Flow onnection Pressure Order Preis rate thread range number D mm mm mm l/min* 1 NPT bar ooster / Differential Regulator P 1 max. 10 bar, relieving, K v = 0.1 m 3 /h with constant bleed, transmission ratio 1:1 53.19 53.24 54 127 11 handwheel 280 ¼ NPT 0.2 1 53.2201.00 25,00 0.14 8 53.2204.00 25,00 with tapped exhaust 0.2 1 53.2401.00 320,00 0.14 8 53.2404.00 320,00 54 127 11 adjusting screw 280 ¼ NPT 0.2 1 53.1901.00 255,00 0.14 8 53.1904.00 255,00 53.2204.00 gas 1 booster control differential pressure adjustment + 1 bar ooster gas 2 Example 1: constant differential pressure of 1 bar at high flow Example 2: constant differential pressure of 1 bar 53.1904.00 pressure regulator e.g. 3 bar differential pressure adjustment, e.g. 2 bar volume booster supply: bar supply: bar : 5 bar control of volume booster G 1 8 ¼ NPT 29 9.5 G 1 8 ¼ NPT 12 53.22 * 1 at 7 bar supply pressure and 1.4 bar pressure 53.19 53.2201.00.03
Precision Volume ooster with Transmission Ratio R750 The volume booster with transmission ratio amplifies the pressure at a 1:1 up to 1: ratio by a pneumatic pressure, which has no constant bleed. That pressure has the same function as a spring in a common regulator: generating counter pressure on the diaphragm. This force is compensated by the pressure on the diaphragm's bottom side. The ratio of pressure to pressure depends on the size of the operating diaphragms. compressed air or non-corrosive gases Supply pressure max. 17 bar Pilot pressure max. 10 bar at 1:1 ratio, 5 bar at 1:2, 3.3 bar at 1:3, 1.7 bar at 1:, ccuracy at supply variation of 3.5 bar: < 7 mbar 1:1, < 10 mbar at 1:2, < 21 mbar at 1:3, < 41 mbar at 1: response sensitivity: < 2 mbar 1:1, < 3 mbar at 1:2, < 17 mbar at 1:3, < 23 mbar at 1: ir consumption max. 3 l/min, subject to pressure Relieving function relieving Relief capacity 170 l/min at 1.5 bar and 0.7 bar overpressure above setpoint Gauge on both sides of the body, thread equal to regulator thread Mounting position any Temperature range 0 to 70 / 32 F to 158 F, for appropriately conditioned compressed air down to -40 / -40 F Material ody: zinc die-cast Elastomer: NR/una-N Inner valve: brass and stainless steel and G 3 8, 1 000 l/min 1:1 up to 1: Dimensions K v - Flow onnection Signal Transmission Order Preis value rate thread pressure ratio number D mm mm mm (m ³ /h) m ³ /h* 1 l/min* 1 G max. bar : ooster with transmission ratio, supply pressure max. 17 bar, relieving, with constant bleed, pressure range 0 10 bar R750 8 102 1 0.5 0 1 000 10 1:1 R750-02I 225,00 5.0 1:2 R750-02K 290,00 3.3 1:3 R750-02 335,00 1.7 1: R750-02M 335,00 8 102 1 0.5 0 1 000 G 3 8 10 1:1 R750-03I 225,00 5.0 1:2 R750-03K 290,00 3.3 1:3 R750-03 335,00 1.7 1: R750-03M 335,00 R750 ooster negative bias factory-set to -0,3 bar R750-0.. Y NPT connection thread R750-0.. N tapped exhaust connection thread R750-0.. X12 ccessories pressure Ø 50 mm, 0 * 2 bar, M5002-..* 2 9,50 mounting bracket made of steel W00-33 12,00 58 Ø9 18 45 R750 W00-33 * 1 at 7 bar supply pressure and 1.4 bar pressure * 2 02 = 0 2.5 bar, 04 = 0 4 bar, 0 = 0 bar, 10 = 0 10 bar, 1 = 0 1 bar R750-02I.04
Precision Volume ooster with High Relief apacity R03-J Pilot-operated volume booster with positive bias designed to supply pressure equal to pressure plus an adjustable preset spring constant. With very high forward and reverse flow characteristics and excellent sensitivity. If requested the system pressure can also manually be adjusted up to bar adding to the pressure. oil-free and 5 μm filtered compressed air or non-corrosive gases Supply pressure max. 1 bar Pilot pressure max. 10 bar, accordingly lower in the case of manual pre-pressure setting, G 1 8 ccuracy at supply pressure change from 2 bar to 7 bar: < mbar pressure deviation at flow rate change from 0 l/min to 20 l/min: < 20 mbar pressure deviation response sensitivity: < 2 mbar ir consumption 1.5 l/min at P1= 5 bar, 2 l/min at P1= 7 bar, 4 l/min at P1= 10 bar, < 1% of volume flow Relieving function relieving Relief capacity 700 l/min at bar and 0.35 bar overpressure above setpoint Gauge on both sides of the body, one screw plug supplied Mounting position any Temperature range 0 to 0 / 32 F to 140 F, for appropriately conditioned compressed air down to -30 / -22 F Material ody: zinc die-cast Elastomer: NR/una-N up to G½, 4 500 l min parallel translation Dimensions K v - Flow onnection Positive Pressure Order Preis value rate thread bias range number D mm mm mm (m ³ /h) m ³ /h* 1 l/min* 1 G bar bar Volume booster R03-J 82 10 41 2.0 198 3 300 * 3 without 0.05 10 R03-02J 230,00 2.3 228 3 800 G 3 8* 3 R03-03J 230,00 2.7 270 4 500 G½ R03-04J 230,00 supply pressure max. 1 bar, with constant bleed, Positive bias booster R03-J. 82 142 41 2.0 198 3 300 * 3 0 1 bar 0.05 10 R03-02J1 25,00 2.3 228 3 800 G 3 8* 3 R03-03J1 25,00 2.7 270 4 500 G½ R03-04J1 25,00 82 180 41 2.0 198 3 300 * 3 0 bar 0.05 10 R03-02J 295,00 ccessories supply pressure max. 1 bar, with constant bleed, tapped exhaust, transmission ratio 1:1 tapped exhaust, transmission ratio 1:1 2.3 228 3 800 G 3 8* 3 R03-03J 295,00 2.7 270 4 500 G½ R03-04J 295,00 pressure Ø 50 mm, 0 * 2 bar, M5002-..* 2 9,50 mounting nut made of plastic for R03-..J1 M30x15K 2,00 mounting bracket made of steel W00-3 10,00 R03-..J R03-..J1 ooster 54 Ø5.5 32 17 4 W00-3 R03-..J 7 pressure [bar] 5 R03-04J supply pressure 7 bar 4 G 1 8 G 1 8 3 2 1 0 0 1000 2000 3000 4000 5000 flow rate [l/min] R03-..J1 exhaust G 3 8 R03-..J * 1 at 7 bar supply pressure, bar pressure and 1 bar pressure drop * 2 02 = 0 2.5 bar, 04 = 0 4 bar, 0 = 0 bar, 10 = 0 10 bar, 1 = 0 1 bar * 3 standard unit G½ reduced to smaller threads by fittings R03-02J.05
Precision Volume ooster with Transmission Ratio R208 The volume booster amplifies the volume at a 1:1 ratio of pressure to pressure. The pressure has no constant bleed and shows the same function as a spring in a common regulator: generating counter pressure on the diaphragm. compressed air or non-corrosive gases Supply pressure max. 17 bar Pilot pressure max. 10 bar at 1:1 ratio, 5 bar at 1:2, 3.3 bar at 1:3, 2.5 bar at 1:4, 1.7 bar at 1: Pilot ccuracy at supply pressure variation of 7 bar: < 7 mbar pressure deviation transmission error: 1% from 1:1 to 1:3 ratio, 2% at greater or inverse transmission response sensitivity: 1 mbar at 1:1, 2 mbar at 1:2, 3 mbar at 1:3 and at inverse transmission ir consumption max. 3 l/min, subject to pressure Relieving function relieving Relief capacity 310 l/min at 1.5 bar and 0.35 bar overpressure above setpoint Gauge on both sides of the body, screw plugs supplied Mounting position any Temperature range 0 to 80 / 32 F to 17 F, NR, for appropriately conditioned compr. air down to -40 / -40 F 0 to 90 / 32 F to 194 F, FKM, for appropriately conditioned compr. air down to -40 / -40 F Material ody: aluminium die-cast Elastomer: NR/una-N Inner valve: brass and zinc-plated steel and G 3 8, 1 300 l/min 1:1 up to 1:, 2:1 up to 5:1 Dimensions K v - Flow onnection Pilot Transmission Order Preis value rate thread pressure ratio number D mm mm mm (m ³ /h) m ³ /h* 1 l/min* 1 G max. bar : Volume ooster with transmission ratio, supply pressure max. 17 bar, relieving, with constant bleed, pressure range 0 10 bar R208 7 98 24 0.7 78 1 300 10 1 : 1 R208-02I 315,00 5.0 1 : 2 R208-02K 345,00 3.3 1 : 3 R208-02L 345,00 7 110 24 0.7 78 1 300 2.5 1 : 4 R208-02M 435,00 2.0 1 : 5 R208-02N 435,00 1.7 1 : R208-02O 435,00 7 98 24 0.7 78 1 300 10 2 : 1 R208-02R 345,00 3 : 1 R208-02S 345,00 7 110 24 0.7 78 1 300 10 4 : 1 R208-02T 435,00 5 : 1 R208-02U 435,00 R208 ooster G 3 8 connection thread R208-03. +10,00 NPT connection thread R208-02.N +10,00 non-relieving* 3 without relieving function R208-02.K +85,00 tapped exhaust* 3 connection thread R208-02.X12 +170,00 bypass with restrictor between control chamber and, 1:1 only R208-02.X1 +75,00 negative bias* 3 preset to -0,24 bar, adjustable by 30 mbar R208-02.Y +45,00 silicone elastomer supply pressure max. 5 bar, 1:1 only R208-02. +105,00 FKM elastomer R208-02.V +15,00 ypass valve (optional) upper diaphragm lower diaphragm ccessories pressure Ø 50 mm, 0 * 2 bar, M5002-..* 2 10,50 mounting bracket made of steel W00-34 12,00 regulating valve 58 Ø9 18 37 R208 W00-34 * 1 at 7 bar supply pressure and 1.4 bar pressure * 3 only for 1:1, 1:2, 1:3, 2:1 and 3:1 * 2 02 = 0 2.5 bar, 04 = 0 4 bar, 0 = 0 bar, 10 = 0 10 bar, 1 = 0 1 bar R208-02I.0
Precision Volume ooster with High Flow R450 The volume booster amplifies the volume at a 1:1 ratio of pressure to pressure. The pressure has no constant bleed and shows the same function as a spring in a common regulator: generating counter pressure on the diaphragm. This force is compensated by the pressure on the diaphragm's bottom side. The ratio of pressure to pressure depends on the size of the operating diaphragms. compressed air or non-corrosive gases Supply pressure max. 17 bar Pilot pressure max. 10 bar at 1:1, 2:1 and 3:1 ratio, 5 bar at 1:2, 3.3 bar at 1:3, ccuracy at supply pressure variation of 7 bar: < 7 mbar pressure deviation response sensitivity: 2.5 mbar Internal air consumption max. 3 l/min, depending on pressure Relieving function relieving Relief capacity 1100 l/min at 0.35 bar overpressure above setpoint Gauge on both sides of the body, screw plugs supplied Mounting position any Temperature range 0 to 90 / 32 F to 194 F, for appropriately conditioned compressed air down to -40 / -40 F Material ody: aluminium die-cast Elastomer: NR/una-N, optionally FKM Inner valve: brass and aluminium 4 200 l/min 1:1 up to 1:3, 2:1 and 3:1 Dimensions K v - Flow onnection Pilot Transmission Order Preis value rate thread pressure ratio number D mm mm mm (m ³ /h) m ³ /h* 1 l/min* 1 G max. bar : Volume ooster with transmission ratio, supply pressure max. 17 bar relieving, with constant bleed, pressure range 0 10 bar R450 87 129 40 2.1 240 4 000 G½ 10 1 : 1 R450-04I 790,00 5.0 1 : 2 R450-04K 845,00 3.3 1 : 3 R450-04L 845,00 10 2 : 1 R450-04M 845,00 10 3 : 1 R450-04N 845,00 87 129 40 2.1 252 4 200 G¾ 10 1 : 1 R450-0I 790,00 5.0 1 : 2 R450-0K 845,00 3.3 1 : 3 R450-0L 845,00 10 2 : 1 R450-0M 845,00 10 3 : 1 R450-0N 845,00 R450 NPT connection thread R450-0..N +10,00 tapped exhaust G½ connection thread, total height 148 mm R450-0..X12 +220,00 bypass with restrictor from control chamber to, 1:1 only R450-0.. X1 +45,00 external feedback with connection thread G 1 8 R450-0.. X27 +280,00 FKM elastomer R450-0.. V +155,00 ccessories pressure Ø 3 mm, 0 * 2 bar, M302-..* 2 10,50 mounting bracket made of steel W00-477 73,00 3,00 ypass valve (optional) diaphragm poppet valve control diaphragm exhaust valve connecting tube aspirator tube ooster 39.5 27.5 Ø5.5 Ø5.5 supply valve motor diaphragm 27 20 25 Ø9 W00-47 G 1 2 tapped exhaust G 1 8 external feedback R450 * 1 at 7 bar supply pressure and 1.4 bar pressure * 2 02 = 0 2.5 bar, 04 = 0 4 bar, 0 = 0 bar, 10 = 0 10 bar, 1 = 0 1 bar R450- X12X27 R450-04I.07
Precision Volume ooster with High Exhaust R490 The volume booster amplifies the volume at a 1:1 ratio of pressure to pressure. The booster is a rugged precision instrument with key features providing reliable, efficient and stable operation. Very low deadband between the operation of the supply valve and exhaust valve providing provides excellent pressure control. High capacity exhaust valve provides efficient dynamic reverse flow characteristics. Pressure balanced supply valve prevents changes in control characteristics when supply pressure changes. Damped diaphragm control chamber provides stable operation and protects valves from damaging oscillation under high flow conditions. compressed air or non-corrosive gases Supply pressure max. 17 bar Pilot pressure max. 10 bar; ccuracy at supply pressure variation of 7 bar: < 7 mbar pressure deviation response sensitivity: 2.5 mbar ir consumption max. 3 l/min subject to pressure Relieving function relieving Relief capacity 2800 l/min at 0.35 bar overpressure above setpoint of 1.5 bar Gauge ¼ NPT on both sides of the body, screw plugs supplied Mounting position any Temperature range -40 to 93 / -40 F to 199 F Material ody: aluminium die-castdiaphragm: NR/una-N on Polyester, optionally FKM Inner valve: zinc-plated steel, optionally stainless steel 12 000 l/min Dimensions K v - Flow onnection Supply Pressure Order Preis value rate thread pressure range number D mm mm mm (m ³ /h) m ³ /h* 1 l/min* 1 G max. bar : Volume booster transmission ratio 1:1, supply pressure max. 17 bar, relieving, with constant bleed R490 143 188 44 9 850 14 100 G¾ 17 0...10 R490-0 1.980,00 143 188 44 9 850 14 100 G1 17 0...10 R490-08 1.980,00 NPT connection thread R490-0. N +10,00 external feedback with connection thread R490-0. X27 +240,00 FKM elastomere R490-0. V +245,00 inner parts SST all R490-0. S +170,00 R490 ccessories pressure Ø 3 mm, 0 * 2 bar, M302-..* 2 10,50 ooster Transducer ontroller Load Output 1 Supply Molten Metal Mold Volume booster with single acting positioner and diaphragm actuator Volume booster: casting implements exhaust G 3 4 / G1 external feedback optionally P1 R490 R490 * 1 at 7 bar supply pressure and 1.4 bar pressure * 2 02 = 0 2.5 bar, 04 = 0 4 bar, 0 = 0 bar, 10 = 0 10 bar R490-0.08
Precision Volume ooster with High Volume Flow R200 / R201 The volume booster amplifies the volume at a 1:1 ratio of pressure to pressure. The pressure has no constant bleed. The bias spring at booster R200 generates a positive shift of the pressure range between pressure and pressure. ooster R201 with great relief capacity is a combination of two R200 boosters. When the output pressure increases above the pressure, the diaphragm assembly moves upward to close the supply valve and open the exhaust valve. Excess output pressure exhausts through the exhaust until it reaches the setpoint. compressed air or non-corrosive gases Supply pressure max. 17 bar Pilot pressure max. 10 bar, at R200; ¼ NPT at R201 ccuracy at supply pressure variation of 7 bar: < 20 mbar pressure deviation Response sensitivity 30 mbar ir consumption without constant bleed Relieving function relieving, optionally non-relieving Relief capacity 1800 l/min at 0.3 bar overpressure above setpoint at R200, 9 000 l/min at R201 Gauge on both sides of the body at R200; ¼ NPT at R201 Mounting position any Temperature range 0 to 90 / 32 F to 194 F, for appropriately conditioned compressed air down to -40 / -40 F Material ody: aluminium die-cast O-rings: PTFE Diaphragm: NR/una-N Inner valve: stainless steel, cadmium-plated steel and brass G1 and G1½, 1½ NPT 30 000 l/min Dimensions K v - Flow onnection Supply Pressure Order Preis Value rate thread pressure range number D mm mm mm (m ³ /h) m ³ /h* 1 l/min* 1 G max. bar bar ooster with high flow rate R200 supply pressure max. 17 bar, relieving, without constant bleed, transmission ratio 1:1 141 198 57 11.4 1 80 28 000 G1 17 0 10 R200-08I 1.810,00 141 198 57 12.2 1 800 30 000 G1½ 17 0 10 R200-12I 1.810,00 ooster with high exhaust rate supply pressure max. 17 bar, relieving, without constant bleed, transmission ratio 1:1 R201 250 240 57 12.2 1 800 30 000 1½ NPT 17 0 10 R201-12I 4.00,00 NPT connection thread for R200 R200 -.. IN non-relieving without relieving function for R200 R200 -.. IK tapped exhaust connection thread G 3 8 for R200 R200 -.. IX12 FKM elastomer for R200 R200 -.. IV R200 ccessories pressure Ø 3 mm, 0 * 2 bar, M302-..* 2 adapter ¼ NPT male / female for R201 VP-0202N mounting bracket made of steel for R200 W00-41 ooster bias spring R201 R200 70 Ø7 19 W00-41 1 4 NPT 1 4 NPT R201 * 1 at 10 bar supply pressure and 2.8 bar pressure * 2 02 = 0 2.5 bar, 04 = 0 4 bar, 0 = 0 bar, 10 = 0 10 bar, 1 = 0 1 bar R200-08I.09
Precision Volume ooster with High Relief apacity R11 Pilot-operated regulator adapted for control by small remote regulator or by proional pressure valve. Ideal for continuous high-capacity requirements where reduced pressure must be held constant over wide variations in flow. The booster is equipped with a diaphragm. Transmission ratio 1:1 ( pressure to pressure). compressed air or non-corrosive gases Mounting position any Supply pressure max. 28 bar Pilot pressure max. 18 bar Outlet pressure 0.2... 18 bar ir consumption without constant bleed Relieving function 500 l/min at bar, see diagram Response sensitivity 20 mbar Ports / : see chart exhaust: G½ (up to overall size G½), G¾ (from size G¾ on) P2: P1: G 1 8 (from size G¾ on) Temperature range -18 to 70 / 0 F to 158 F Material ody: zinc die-cast Inner valve: brass Elastomer: NR/una-N ottom screw: reinforced nylon G 1 4 up to G1 1 4 12 500 l/min Dimensions Nominal K v - Flow onnection Order Preis size value rate thread number D mm mm mm DN (m ³ /h) m ³ /h* 1 l/min* 1 G ooster with high relief capacity R11 P1: max. 28 bar, ratio 1:1 P2: 0,2... 18 bar, relieving 80 129 39 15 4.3 270 4 500 R11-02 54,00 4.4 290 4 800 G 3 8 R11-03 54,00 4.5 300 5 000 G½ R11-04 54,00 93 149 48 25 9.5 90 11 500 G¾ R11-0 780,00 10.0 720 12000 G1 R11-08 780,00 10.4 750 12500 G1¼ R11-10 812,00 R11-04 accessory: NPT connection thread R11-.. N +10,00 flange connection see chapter SST devices / flanges R11-.. F s.kap.15 ooster ccessories pressure Ø 50 mm, 0 * 2 bar, for to G½ M5002-* 2 9,50 Ø 3 mm, 0 * 2 bar, for G¾ to G1¼ M302-* 2 10,50 mounting bracket made of aluminium W00-32 55,00 G¾ exhaust R11-08 accessory: 88 120 3,0 Ø,5 44 25 4 W00-32 G 1 8 P1 R11 P2 booster booster pressure regulator proional pressure regulator example: booster with pressure regulator example: booster with proional pressure * 1 at 8 bar supply pressure, bar pressure and 1 bar pressure drop * 2 02 = 0 2,5 bar, 04 = 0 4 bar, 10 = 0 10 bar, 1 = 0 1 bar, 25 = 0 25 bar R11-02.10
Precision Volume ooster with High Volume Flow up to G3 R119-J Pilot-operated regulator adapted for control by small remote regulator or by proional pressure valve. Ideal for continuous high-capacity requirements where reduced pressure must be held constant over wide variations in flow. ooster with diaphragm up to regulator size G1½, with piston from regulator size G2 on. The booster is silicone-free. compressed air or non-corrosive gases Supply pressure max. 21 bar Pilot pressure max. 18 bar Pilot G 1 8 at regulator size and G 3 8, from regulator size G½ on ir consumption approx. 1 l/min of Relieving function relieving as standard, optionally non-relieving Gauge on both sides of the body Mounting position any Temperature range 0 to 50 / 32 F to 122 F up to 80 / 17 F at G3 Material ody: zinc die-cast, aluminium at G3 Inner valve: brass Diaphragm: NR/una-N, optionally FKM ottom screw: reinforced nylon G 1 4 up to G3 110 000 l/min Dimensions Nominal K v - Flow onnection Order Preis size value rate thread number mm mm mm DN (m ³ /h) m ³ /h* 1 l/min* 1 G Volumenstrombooster Eingangsdruck max. 21 bar, usgangsdruck 0,2 18 bar mit Eigenluftverbrauch, Übersetzung 1:1, rücksteuerbar R119-J 70 8 35 5 2.1 102 1 700 R119-02J 172,00 70 8 35 10 2.8 150 2 500 G 3 8 R119-03J 172,00 83 98 37 15 5.0 340 5 00 G½ R119-04J 192,00 113 123 49 20 7. 540 9 000 G¾ R119-0J 279,00 113 123 49 25 8.4 00 10 000 G1 R119-08J 279,00 125 132 48 32 9.2 0 11 000 G1¼ R119-10J 4,00 125 132 48 40 10.0 720 12 000 G1½ R119-12J 4,00 18 225 79 50 35.4 2 520 42 000 G2 R119-1J 1.004,00 18 225 79 5 37.1 2 40 44 000 G2½ R119-20J 1.004,00 214 282 95 80 5.0 00 110 000 G3 R119-24J 2.247,00 R119-10J, accessory: NPT connection thread R119-.. JN +10,00 non-relieving without relieving function R119-.. JK + 2,50 FKM elastomer for to G1½ R119-.. JX4 +140,00 for G3 R119-24JX4 +50,00 without constant bleed insided the chamber for to G1½ R119-.. JX71 +20,00 flange connection see chapter for SST devices / flanges R119-.. JF s.kap.15 external feedback for increased accuracy for G3 R119-24JX27 +70,00 pre-pressure regulation 340 mbar, advisable if P1 is close to P2 for G3 R119-24JX0 +45,00 ccessories pressure Ø 50 mm, 0 * 2 bar, for to G½ M5002-* 2 9,50 Ø 3 mm, 0 * 2 bar, for G¾ to G3 M302-* 2 10,50 mounting bracket made of steel for and G 3 8 W00-22 13,50 for G½ W00-23 13,50 for G¾ to G1½ W00-24 30,00 R119-1J, accessory: R119-24J, accessory: ooster 28 4.5 54 10 7 89 10 7 11 17 34 25 57 75 W00-22 W00-23 W00-24 G 1 8 ( from size G 1 2 on) R119-02J../-12J R119-1J/-20J * 1 at 8 bar supply pressure, bar pressure and 1 bar pressure drop * 2 02 = 0 2.5 bar, 04 = 0 4 bar, 10 = 0 10 bar, 1 = 0 1 bar, 20 = 0 20 bar, 25 = 0 25 bar R119-24J R119-02J.11
Low Pressure Volume ooster up to 1000 bar, Supply Pressure max. 20 bar RZ-J 0 Supply pressure Highly sensitive diaphragm low pressure volume booster with excellent regulating characteristics. compressed air or non-corrosive gases max. 20 bar depending on the accuracy: the smaller P 1 the higher the accuracy max. 10 bar at pressure range < 150 mbar ccuracy at max. flow rate < e.g. 10% pressure deviation of full scale ir consumption without constant bleed djustment manual by turning the spindle under the cover of the spring cage Relieving function non-relieving Gauge not available Mounting position any Temperature range -20 bis 0 / -4 F to 140 F Material ody: SG cast iron GGG50, GGG40 at G2 Elastomer: NR/una-N, optionally FKM Spring cage: aluminium Inner valve: brass and stainless steel G1 up to G2 10 150/ 1 000 mbar Dimensions ccuracy Nominal Flow P 1 onnection Pressure Order Preis size rate max. thread range number D mm mm mm % DN l/min* 1 bar* 2 G mbar Low pressure volume booster supply max. 20 bar, non-relieving, 1:1 transmission ratio RZ-J 100 245 30 10 17 1 800 10 G1 15 110 RZ1-08J 590,00 5 3 300 20 180 1000 RZ3-08J 720,00 130 250 30 10 17 2 700 10 G1½* 3 15 110 RZ1-12J 770,00 5 5 000 20 180 1000 RZ3-12J 900,00 200 385 45 10 34 15 000 10 G2 10 350 RZ1-1JF 1.920,00 5 28 000 20 350 1000 RZ2-1JF 1.920,00 RZ1-08J ooster relieving with relieving function RZ.-...R + 5% FKM elastomer RZ.-...V +2,00 flange connection see chapter for SST devices / flanges (not for RZ.-1J) RZ.-... F. s.kap.15 nitrogen N 2 : 07 carbon dioxide O 2 : 03 argon r: RZ.-...05 + 15% helium He: 09 hydrogen H 2 : 11 methane H 4 : RZ.-...13 + 15% oxygen O 2 : 15 propane 3 H : 1 nitrous oxide N 2 O: RZ.-...17 + 15% RZ1-1JF RZ.-08/12J RZ.-1JF with flange * 1 at 4 bar supply pressure and max. pressure * 2 see description above * 3 G1 thread at RZ1-08J.12
Low Pressure Volume ooster up to 350 mbar RGDJ-J / RG4-J Highly sensitive low pressure volume booster with diaphragm and a 1:1 transmission ratio. Zero shut-off prevents the pressure from increasing when there is no flow circulating. compressed air or non-corrosive gases Supply pressure max. 400 mbar at RGDJ-J, max. 4 bar at RG4-J Pilot pressure max. 100 mbar at RGDJ-J, max. 350 mbar at RG4-J, ir consumption without constant bleed Relieving function non-relieving ccuracy at maximum volume flow: < 20% pressure deviation of full scale Gauge not available, optionally on one side of the body from regulator size G¾ on Mounting position any Temperature range RGDJ-J: -20 to 70 / -4 F to 158 F RG4J: -15 to 0 / -4 F to 140 F Material ody: aluminium Inner valve: aluminium and plastic Elastomer: NR/una-N G½ up to G2 2 55 / 350 mbar Dimensions Nominal Kv- Flow onnection Pressure Order Preis size Value rate thread range number D mm mm mm DN (m 3 /h) m 3 /h* 1 l/min* 1 G mbar Low pressure booster RGDJ-J supply pressure max. 400 mbar, non-relieving, without constant bleed, transmission ratio 1:1 100 120 30 15 0. 12 200 G½ 2 55 RGDJ-04J 228,00 134 1 34 20 1.49 27 450 G¾ 5 10 RGDJ-0J 255,00 134 1 34 25 2. 51 850 G1 5 10 RGDJ-08J 284,00 185 194 45 40 4.9 90 1 500 G1½ 5 10 RGDJ-12J 447,00 234 219 52 50. 120 2 000 G2 5 100 RGDJ-1J 582,00 Low pressure booster supply pressure max. 4 bar, non-relieving, without constant bleed, transmission ratio 1:1 RG4-J 132 174 24 15 0.2 42 700 G½ 5 350 RG4-04J 830,00 190 230 33 25 2.5 18 2 800 G1 5 350 RG4-08J 935,00 190 25 55 40 5 33 5 00 G1½ 5 350 RG4-12J 1.140,00 RGDJ-04J connection thread for pressure not for RGDJ-04J RG.. -...M +40,00 ccessories preassure Ø 3 mm, 0 * 2 mbar, for G¾ up to G2 M302-..* 2 72,00 ooster ΔP pressure difference *3 mbar 300 flow dependence on supply and pressure 200 100 80 0 50 40 30 20 RGDJ RG4-12JM accessory: RGDJ-J 10 8 5 4 3 l 20 40 0 100 300 500 800 2000 10 30 80 200 400 00 1000 flow rate l/min ΔP pressure difference *3 flow dependence on supply and pressure mbar 3000 2000 1000 800 00 500 400 300 200 RG4-J * 1 at 350 mbar supply pressure and 100 mbar pressure * 2 = 0 0 mbar, 2 = 0 10 mbar, 4 = 0 400 mbar 100 80 RG4 0 50 40 30 20 200 400 00 1000 3000 5000 8000 20000 100 300 500 800 2000 4000 000 10000 flow rate l/min * 3 ΔP= P 1 - P 2 Pressure difference between supply and pressure RG4-J RGDJ-04J.13
High Pressure Volume ooster with Transmission Ratio, up to 310 bar RH3-J Highly reliable high pressure volume booster with diaphragm and high flow. In addition, the booster features high sensitivity and excellent regulating characteristics. compressed air, non-corrosive gases or liquids Supply pressure max. 20 bar, optionally 345 bar or 310 bar Test pressure 150% of maximum supply pressure according to regulations NSI / SME 31.3 Pilot pressure see chart, G 1 8 Leakage rate < 1x 10-4 mbar l/s He ir consumption without constant bleed Relieving function non-relieving Gauge not available, optionally ¼ NPT at and Mounting postition any Temperature range -25 to 100 / -13 F to 212 F Material ody: brass, optionally stainless steel Elastomer: FKM Inner valve: PTFE, brass or optionally stainless steel 1 2 NPT, 1:2 up to 1:19 P 1 : max. 20 / 310 bar Dimensions K v - Flow Signal Pressure Transmission Order Preis value rate pressure range ratio number D mm mm mm (m ³ /h) m ³ /h* 1 l/min* 1 max. bar bar s ignal : High pressure booster supply pressure max. 20 bar, non-relieving, ½ NPT without constant bleed, without RH3-J 7 170 45 1.7 420 7 000 21 3 42 1 : 2 RH3-J402 1.800,00 17 5 70 1 : 4 RH3-J404 1.800,00 5 3 42 1 : 8 RH3-J408 1.800,00 5 5 70 1 : 13 RH3-J413 1.800,00 5 10 104 1 : 19 RH3-J419 1.800,00 ooster ¾ NPT connection thread RH3-J.. +45,00 stainless steel 310 bar body made of stainless steel 31 RH3-J...S1 +00,00 ¼ NPT for and RH3-J...M +95,00 brass for brass body, on the input side HM +output side RH3-J...MGM+74,00 stainless steel for stainless steel body, on the input side H + output side RH3-J...MG +130,00 RH3-J ccessories set of brackets for panel mounting 1129 5,00 G 1 8 ¼-20 UN 1129 IN OUT RH3-J panel cut-out connection, option M * 1 at 210 bar supply pressure and 40 bar pressure RH3-J402.14
Volumenstrombooster aus Messing, bis 50 bar R120-J Solid volume booster made of brass or bronze throughout with a 1:1 transmission ratio. R120-02J2 to R120-08J2 are diaphragm-operated, R120-12J, R120-1J and R120-..J5 are piston-operated. compressed air, non-corrosive gases or liquids Supply pressure max. 50 bar, for liquids Δpmax. = 25 bar Pilot pressure max. 15 bar for R120-..J2, max. 50 bar for R120-..J5, ir consumption without constant bleed Relieving function non-relieving, optionally relieving Relief size DN2 Gauge on both sides of the body, one screw plug supplied Mounting position any Temperature range 0 to 80 / 32 F to 17 F for FKM or EPDM 0 to 130 / 32 F to 2 F for high temperature version, for appropriately conditioned compressed air down to -20 / -4 F, optionally low temperature version down to -40 / -40 F Material ody: brass up to G½, bronze from G¾ on O-rings: FKM, optionally EPDM Diaphragm: NR/una-N with PTFE coating Inner valve: brass up to G2 1 15 / 50 bar Dimensions Regul. system K v Flow onnection Signal Pressure Order Price D: diaphragm value rate thread pressure range number mm mm mm P: piston (m ³ /h) m ³ /h* 1 l/min* 1 G max. bar bar ooster aus Messing Eingangsdruck max. 50 bar, nicht rücksteuerbar, ohne Eigenluftverbrauch, Übersetzung 1:1 R120-J 4 79 38 M 0.35 25 420 15 1... 15 R120-02J2 225,00 4 92 38 K 50 1... 50 R120-02J5 280,00 80 8 38 M 1 72 1 200 G½ 15 1... 15 R120-04J2 225,00 80 107 38 K 50 1... 50 R120-04J5 280,00 11 13 5 M 3.5 252 4 200 G¾ 15 1... 15 R120-0J2 520,00 11 150 5 K 50 1... 50 R120-0J5 725,00 11 13 5 M 4.2 300 5 000 G1 15 1... 15 R120-08J2 520,00 11 150 5 K 50 1... 50 R120-08J5 725,00 195 140 84 K 11.8 840 14 000 G1½ 50 1... 50 R120-12J5 1.720,00 195 190 84 K 12. 900 15 000 G2 50 1... 50 R120-1J5 1.720,00 R120-02J2, accessory relieving diaphragm for R120-02J2 to R120-08J2 R120-.. J.R + 5% relieving piston for R120-12J, R120-1J and R120-..J5 R120-.. J.R +20% up to -40 / - 40 F low temperature version R120-.. J.X51 +30% up to 130 / 2 F high temperature version R120-.. J.X54 +30% EPDM elastomer not for G2 R120-.. J.E +10% tapped exhaust R120-.. J.RX12+20% nitrogen N 2 : 07 carbon dioxide O 2 : 03 argon r: R120-.. J.05 +15% helium He: 09 hydrogen H 2 : 11 methane H 4 : R120-.. J.13 +15% oxygen O 2 : 15 propane 3 H : 1 nitrous oxide N 2 O: R120-.. J.17 +15% water H 2 O: R120-.. J.W +15% ccessories pressure Ø 50 mm, 0 * 2 bar, for and G½ M5002-..* 2 9,50 pressure Ø 3 mm, 0 * 2 bar, for G¾ up to G2 M302-..* 2 10,50 mounting bracket made of steel for G¾ and G1 W00-42 20,00 for G1½ and G2 W00-43 80,00 R120-04J2, accessory ooster 7 104 9 7 92 8 R120-08J2, accessory 31 38 73 8 W00-42 W00-43 : with piston R120-02/04J R120-0/08/12/1J * 1 at 8 bar supply pressure, bar pressure and 1 bar pressure drop * 2 02 = 0 2.5 bar, 0 = 0 bar, 10 = 0 10 bar, 1 = 0 1 bar, 0 = 0 0 bar : with diaphragm R120-02J2.15
High Pressure ooster up to 100 bar RLM / RLE The pressure regulator / booster regulates the pressure through a pressure at ratio of 1:1. Functioning as a pressure regulator the pressure may either be internally inducted from the pressure or externally. The dome chamber is closed by a needle valve. Functioning as a volume booster the dome is controlled by a proional pressure regulator or a pressure regulator. compressed air, non-corrosive gases or liquids Supply pressure max. 25 bar for RL.-0.J1, max. 100 bar for RL.-0.J2, max. 40 bar for oxygen, max. 1.5 bar for acetylene Pilot pressure max. 24 bar for RL.-0.J1, max. 99 bar for RL.-0.J2, ccuracy at supply pressure variation of 10 bar: 0.1 bar pressure deviation at temperature variation of 3 / K: 1% pressure deviation at internal pressure ir consumption without constant bleed Relieving function non-relieving Gauge not available Mounting position any, dome preferably mounted up Temperature range -20 to 100 / -4 F to 212 F for FKM, -40 to 130 / -40 F to 2 F for EPDM Material ody: brass or stainless steel 1.4571 Inner valve: brass or stainless steel 1.4571 Elastomer: FKM, optionally EPDM G1, 0.1 24 / 99 bar brass or stainless steel Dimensions K v - Flow onnection Supply Pressure Order Price value rate thread pressure range number D mm mm mm (m ³ /h) m ³ /h* 1 l/min* 1 G max. bar* 2 bar rass pressure regulator supply pressure max. 25 / 100 bar, non-relieving without constant bleed, transmission ration 1:1, FKM RLM 127 170 54 2.9 340 5 00 G1 25 0.1 24 RLM-08J1 730,00 2500 0 000 G1 100 0.5 99 RLM-08J2 730,00 RLM, made of brass SST pressure regulator supply pressure max. 25 / 100 bar, non-relieving without constant bleed, transmission ration 1:1, FKM RLE 127 170 54 2.9 340 5 00 G1 25 0.1 24 RLE-08J1 3.100,00 2500 0 000 G1 100 0.5 99 RLE-08J2 3.100,00 ooster EPDM elastomer RL. -0.J.E +80,00 nitrogen N 2 : 07 carbon dioxide O 2 : 03 argon r: RL. -0.J.05 + 15% helium He: 09 hydrogen H 2 : 11 oxygen O 2 : RL. -0.J.15 + 15% propane 3 H : 1 nitrous oxide N 2 O: RL. -0.J.17 + 15% RLE, made of stainless steel G 1 8 RL. * 1 RL.-J1: at 25 bar supply pressure and 5 bar pressure * 2 supply pressure max. 40 bar for oxygen * 1 RL.-J2: at 85 bar supply pressure and 70 bar pressure supply pressure max. 1.5 bar for acetylene* 1 RLM-08J1.1