General Information Thermoplastic Tubing/Fitting Reference Guide Tube Max. Recom. Tube Wall Min. end Working Min. urst O.D. Thickness Radius Pressure Pressure Style (Inches) (Inches) (Inches) (PSI) (PSI) Fittings Poly-Flo 1 /8.020 1/2 125 500 Poly-Flo (Polyethylene) 5/32.025 5/8 125 500 Poly-Flo Kwik-onnect ouplings (1/4 & 3/8 O.D.) P 3/16.030 3/4 125 500 PE 1/4.040 1 100 400 5/16.062 1 1 /8 150 600 3/8.062 1 1 /4 90 350 1/2.062 2 1 /2 65 250 Impolene 1/8.023 1/2 225 900 Poly-Flo with 261U Universal Nut & Sleeve (Polyallomar) 3/16.034 3/4 225 900 Poly-Flo Kwik-onnect ouplings (1/4 & 3/8 PP 1/4.040 1 225 900 O.D.) with 261U Universal Nut & Sleeve PY 3/8.062 1 1 /4 225 900 1/2.062 2 1 /2 188 750 Nylo-Seal 1 /8.017 1/2 375 1500 Poly-Flo with 261U Universal Nut & Sleeve (Nylon 11) 5/32.022 5/8 375 1500 Poly-Flo Kwik-onnect ouplings (1/4 & 3/8 SN 3/16.024 3/4 375 1500 O.D.) with 261U Universal Nut & Sleeve NT 1/4.033 1 375 1500 OmegaFlo 5/16.040 1 1 /2 375 1500 Hi-Duty * 3/8.048 1 3 /4 375 1500 Hi-Seal * 1/2.062 2 3 /8 375 1500 Nylo-Seal 1 /8.026 3/8 625 2500 Poly-Flo (1/8 & 3/16 O.D. only) with 261U (Nylon 11) 3/16.039 5/8 625 2500 Universal Nut & Sleeve NSR 1/4.050 7/8 625 2500 OmegaFlo 3/8.075 1 1 /2 625 2500 Hi-Duty * 1/2.075 2 1 /2 500 2000 Hi-Seal * Nylo-Seal 1 /8.023 3/8 250 1000 Poly-Flo with 261U Universal Nut & Sleeve (Nylon 11) 5/32.024 1/2 250 1000 Poly-Flo Kwik-onnect ouplings (1/4 & 3/8 O.D.) NF 3/16.024 5/8 250 1000 OmegaFlo 1/4.033 7/8 250 1000 Hi-Duty * 1/4.040 1/2 300 1200 Hi-Seal * 5/16.040 1 1 /4 250 1000 3/8.048 1 1 /2 250 1000 3/8.060 3/4 300 1200 1/2.062 2 250 1000 Polyvinyl 1/4.040 1/2 50 200 Poly-Flo hloride 3/8.062 1 40 160 Poly-Flo Kwik-onnect ouplings (1/4 & 3/8 O.D.) PV 1/2.062 2 35 140 Poly-Flo 1 /4.040 1 100 400 Poly-Flo Flame Retardant 3/8.062 1 1 /4 88 350 Poly-Flo Kwik-onnect ouplings (1/4 & 3/8 O.D.) 1/2.062 2 1 /2 63 250 *onsult factory for further information. 1 Insert must be used with SN tubing when temperature exceeds 180 F and with NF tubing under all temperature conditions. 2 Insert must be used with Poly-Flo tubing under all temperature conditions.
General Information Imperial Eastman Fittings and Tubing GENERL INFORMTION Fitting Descriptions...2-3 Fitting Identification hart...4-5 Part No. Designation Guide...6 Fitting Selector Guide...6 Thread Size hart...7 INDEX REFERENE DT Decimal and Metric Equivalents of Fractions...97,104 How to Install Tubing...104 Recommended Tubing Flare Dimensions...103 Thermoplastic hemical Resistance hart...105-106 ssembly Instructions For: Hi-Duty flareless tube fittings...8 45 flare tube fittings...8 ompresamatic flareless tube fittings...8 ompression flareless tube fittings...8 Flex flareless tube fittings...9 Omega-Flo flareless tube fittings...8 Poly-Flo flareless tube fittings...8 Poly-Flo Kwik-onnect couplers...8 LPH-NUMERI PRT NO. INDEX...107 TEHNIL DT Decimal & Metric Equivalents...108 onversion Factors...109-111 Temperature onversion...112 HI-SEL Design Features...10 Minimum Working Pressures...12-16 Derating Factors...17 ssembly Instructions...18-19 Ordering Information...21-22 TUE FITTINGS Poly-Flo Flareless...23-32 Poly-Flo Kwik-onnect ouplers...33-36 OmegaFlo Push-To-onnect...37-39 Hi-Duty Flareless...40-45 Flex Flareless...46-48 ompression Flareless...49-53 ompresamatic Flareless...54-59 45 Flare...60-68 HI-SEL FITTINGS Steel...69-73 Steel O-Ring...74 Stainless Steel...75-82 raze-seal...83 rass...84-90 PIPE FITTINGS rass...91-96 THERMOPLSTI TUING urst vs. Temperature Data...98-99 Style 6, ir rake...102 Poly-Flo...100 Poly-Flo Flame Retardant...100 Impolene...100 Nylo-Seal...102 PV...102 1
General Information Fitting Descriptions Working Pressure Style Maximum Nominal onstruction pplication ompatible Tubing Poly-Flo 500 PSI 125 PSI Three-piece: body, nut Pneumatic instrumentation Polyethylene sleeve circuits Polypropylene Shapes: brass, forged Fluid piping systems Nylon SE 377 or equal Polyvinyl chloride Straights: brass, SE Polyallomar 360 or equal Soft metal Sleeves: elcon or Poly-Flo rass Nylo-Seal (SN, NF) Impolene Poly-Flo 500 PSI 125 PSI ody and nuts: hrome- Low pressure instrumentation Polyethylene Kwik-onnect plated brass or Type 316 lines requiring frequent Polypropylene stainless steel connecting and disconnecting Nylon Sleeves: elcon Medical and dental equipment Polyvinyl chloride Springs: Stainless steel Polyallomar O-Rings: una N on brass Soft copper couplings, Viton on Poly-Flo stainless steel couplings Nylo-Seal Impolene OmegaFlo 300 PSI 125 PSI One-piece unit Pneumatic instrumentation Polyethylene Shapes: brass, forged circuits Nylon 11 SE 377 or equal Fluid piping systems Soft copper Sleeves: SE 360 Poly-Flo or equal Nylo-Seal Straights: brass SE Impolene 360 or equal Hi-Duty 4,300 PSI 800 PSI Two piece: body and Instrumentation systems opper nut/sleeve Mobile farm and mobile rass Shapes: brass, forged SE construction equipment Seamless steel 360 or equal Hydraulic and pneumatic Thermoplastic Flareless compression controls design Process control systems Laboratory equipment Flex 1,000 PSI 200 PSI Three piece: body, nut High vibration and opper and elastomeric sleeve shock conditions rass Shapes: brass, forged Diesel engine fuel lines luminum SE 377 or equal Lubrication systems Steel Straights: brass, SE Gasoline, air and Glass 360 or equal water lines Thermoplastic Flareless Special compound sleeves available to 450 F ompression 400 PSI 250 PSI Three-piece: body, nut Low pressure air, oil, opper and sleeve water and gas piping rass Shapes: brass, forged Meets SE J512 luminum SE 377 or equal Thermoplastic Straights: brass, SE 360 or equal ompresamatic 4,500 PSI 850 PSI Two-piece: body and ir, oil, water and opper nut/sleeve gas piping rass Shapes: brass, forged Meets SE J512 luminum SE 377 or equal Except for the Thermoplastic Straights: brass, SE nut and sleeve Seamless steel 360 or equal Nuts and sleeves interchangeable with standard compression bodies Maximum working pressure based on 1/8 O.D. dead soft copper tubing. Please consult Imperial Eastman for additional information. 2
General Information Fitting Descriptions Working Pressure Style Maximum Nominal onstruction pplication ompatible Tubing 45 Flare 2,850 PSI 225 PSI Two-piece: body and nut Mobile equipment piping opper Shapes: brass, forged ir compressor piping luminum SE 377 or equal HV applications Seamless steel Straights: brass, SE (requires forged nut) 360 or equal Marine 45 flared Meets SE J512 and J513 NSI 31.1 and 70.1, SME oiler and Pressure Vessel ode Hi-Seal raze Seal 19,250 PSI 5,000 PSI 3-Piece body, Instrumentation systems opper Nut and Sleeve Mobile farm and mobile rass construction equipment Seamless steel vailable in brass, Hydraulic and pneumatic steel and stainless controls steel Process control systems Laboratory equipment rass Pipe 3,000 PSI 1,000 PSI Shapes: rass, Forged ir ompressor Piping rass Pipe SE 377 or equal Water System Piping Iron Pipe Straights: rass, SE oolant Transmission Lines 377 or equal Dryseal Threads Meets all SE rass Pipe Fittings standards Maximum working pressure based on 1/8 O.D. dead soft copper tubing. Please contact Imperial Eastman for additional information. 3
General Information Fitting Identification hart Poly-Flo OmegaFlo Hi-Duty Flex ompression ompresamatic 45 Flare Hi-Seal Male onnector 268P 268OF 88L 68FL 68F 68M 648F 768F Female onnector 266P 266OF 86L 66FL 66F 66M 646F 766F 90 Male Elbow 269P 269OF 89L 69FL 69F 69M 649F 769F 90 Female Elbow 270P 90L 70FL 70F 70M 650F 770F 45 Male Elbow 94L 94FL 74F 74M 654F 754F Union 262P 262OF 82L 62FL 62F 62M 642F 762F ulkhead Union 282P 282OF 72L 782F Union Elbow 265OF 85L 65FL 65F 65M 655F 765F Female ranch Tee 277P 95L 777F 4
General Information Fitting Identification hart Poly-Flo OmegaFlo Hi-Duty Flex ompression ompresamatic 45 Flare Hi-Seal Male ranch Tee 272P 272OFS 92L 72FL 72F 72M 645F 772F Male Run Tee 271P 271OFS 91L 71FL 71F 71M 651F 771F Union Tee 264P 264OF 84L 64FL 64F 64M 644F 659F 764F Nut 261P 812 61FL 61F 61M 511GS 761F 641F Sleeve 260U 60FL 60F 760F ross 652F 752F all heck 83L 63F 63M 643F Reducing Union 256P 87L 656F 756F Reducer 297P 5
General Information Part Number Designation Guide Part Numbers for Tube Fittings To order Imperial Eastman tube fittings, use the diagram below as a guide. Example: ompresamatic fittings with 3/8 tube connection and 1/4 male pipe thread. Part Numbers for Pipe Fittings To order Imperial Eastman brass pipe fittings, use the diagram below as a guide. Example: rass 1/8 NPTF female union. Fitting style Fitting style Tube O.D. size Material Pipe size Pipe size 68M 06 X 04 Part number = 68M06X04 104 02 Part number = 10402 Fitting Selector Guide MXIMUM REOMMENDED WORKING PRESSURE (PSI) FITTING Dash No. FITTING STYLE MTERIL 02 03 04 05 06 08 10 12 14 Hi-Duty 1 rass 4,300 2,850 2,100 1,800 1,500 1,150 1,000 550 400 45 Flare 1 rass 2,850 2,100 1,800 1,500 1,100 1,000 850 750 ompresamatic 1 rass 4,500 2,500 1,750 1,800 1,150 950 750 1,000 ompression 1 rass 400 400 300 300 200 200 150 100 75 Flex elled Tubing 1 rass 2,000 1,500 1,000 900 700 500 400 350 300 Flex Non-elled Tubing 1 rass 1,000 750 500 450 350 200 OmegaFlo rass 300 PSI MXIMUM PolyFlo rass 500 PSI MXIMUM rass Pipe Fittings rass 3,000 PSI MXIMUM 2 2,000 PSI MXIMUM 3 Maximum working pressures depend on tubing material, tube O.D., wall thickness and fitting size. The pressures listed above reflect static pressures at 72 F with the following material and Dash No. /wall thickness. 1 TUING MTERIL: opper dead soft seamless, STM 75, NSI H23.3, 02/.030, 03/.030, 04/.030, 05/.032, 06/.032, 08/.032, 10/.035, 12/.035, 14/.035 2 Exceptions: 101 = 2500 PSI; 102 = 2500 PSI; 104 = 1500 PSI 3 Exceptions: 102 = 1000 PSI; 104 = 625 PSI; 108 = 1500 PSI; 116 = 1500 PSI; 122 = 1500 PSI 6
General Information Thread Size hart Use this chart to determine fitting thread sizes per tube O.D. size. For example: Thread sizes for a Hi-Duty 1/8 fitting, with Part No. 88L02X02 are...5/16-24 tube thread size x 1/8-27 pipe thread size, as below: Fitting Style Tube O.D. Pipe size 88L 02 X 02 PRT NUMER = 88L02X02 TUE SIZE (O.D.) Dash No. 02 03 04 05 06 07 08 10 12 14 16 FITTINGS Size 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 7/8 1 TUE END THREDS Hi-Duty 5/16-24 3/8-24 7/16-24 1/2-20 9/16-20 1 1 /16-16 7/8-18 1-18 1 1 /4-18 45 Flare 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 11/16-16 3/4-16 7/8-14 1 1 /16-14 1 1 /4-12 ompresamatic 5/16-24 3/8-24 7/16-24 1/2-24 9/16-24 5/8-24 11/16-20 13/16-18 1-18 ompression 5/16-24 3/8-24 7/16-24 1/2-24 9/16-24 5/8-24 11/16-20 13/16-18 1-18 Flex 3/8-24 7/16-24 1/2-24 9/16-24 5/8-24 13/16-18 1-18 1 1 /8-18 Poly-Flo and Kwik-onnect 5/16-24 3/8-24 3/8-24 7/16-24 1/2-24 11/16-20 PIPE END THREDS Pipe Fittings 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11 1 /2 7
General Information ssembly Instructions Fitting To ssemble To Reconnect Hi-Duty 1. Using a tube cutter, cut tube squarely and cleanly, 1. Reinsert tubing Flareless removing all burrs. 2. Tighten nut one eighth of a turn more Tube Fittings 2. Grasp fitting. Do not remove nut. than previous make-up. 3. Insert tube in fitting through nut until tube seats firmly NOTE: The Hi-Duty fitting can be against tube shoulder in body. disconnected and reconnected repeatedly 4. Grip tube firmly to prevent turning and tighten nut until and will always reconnect tightly. a slight give is felt. This give indicates the sleeve has been sheared from the nut. 5. ontinue tightening for one and one-half additional turns for a positive, leakproof seal. It is not necessary to tighten the nut all the way down. 45 Flare 1. Using a tube cutter, cut tubing squarely and cleanly, 1. Tighten to original make-up position, plus Tube Fittings removing all burrs. an additional one-sixth turn of the nut 2. Slide nut onto tubing with the open threaded end of (one flat of the hex). the nut facing toward the end to be flared. 3. Flare tubing end with a good quality flaring tool. 4. Position the flare against the nose of the fitting body and align the tube with the fitting. 5. ssemble nut to body, tightening finger tight. 6. Tighten nut with a wrench one-quarter to one-half turn for a leakproof connection. ompression 1. Using a tube cutter, cut tube squarely and cleanly, 1. Tighten to original make-up position, plus Flareless Tube removing all burrs. an additional one-sixth turn of the nut Fittings 2. Insert tubing into the fitting body until it rests against (one flat of the hex). the shoulder. 3. Move sleeve into position and tighten the nut. NOTE: No flaring, soldering or other special preparation of the tubing is necessary before assembly. ompresamatic 1. Using a tube cutter, cut tube squarely and cleanly, 1. Tighten to original make-up position, plus removing all burrs. an additional one sixth turn of the nut 2. Insert the tube into fitting. e sure the tube bottoms (one flat of the hex). on the fitting shoulder. 3. Tighten (hand-tight), and complete the seal with one wrench turn on all sizes. Poly-Flo 1. Using a tube cutter, cut tubing squarely and cleanly, 1. Tighten nut to original make-up position, Flareless removing all burrs. tightening finger tight. Tube Fittings 2. Push tubing into fitting and tighten the nut. NOTE: There is no need to disassemble the fitting before assembly. When used with Poly-Flo or PV tubing, fitting is assembled finger tight. No wrenches needed. Poly-Flo 1. Using a tube cutter, cut tubing squarely and cleanly, 1. Tighten nut to original make-up position, Kwik-onnect removing all burrs. tightening finger tight. ouplers 2. Push tubing into fitting and tighten the nut. NOTE: There is no need to disassemble the fitting before assembly. When used with Poly-Flo or PV tubing, assembly is finger tight. OmegaFlo 1. Using a tube cutter, cut tubing cleanly and squarely. 1. Firmly push tubing into the fitting until it Push-to-onnect/ 2. Firmly push the tubing into the fitting until it will enter will enter no further. properly assembled Push-to-Release no further. properly assembled tube cannot be pulled tube cannot be pulled out by hand. Pneumatic Fittings 8 out by hand. 3. To disconnect, simply push back on the brass collet and release tubing.
Fitting To ssemble To Reconnect General Information ssembly Instructions Flex Flareless 1. Using a tube cutter, cut tube squarely and cleanly, 1.Tighten to original make-up position, Tube Fittings removing all burrs. making sure the nut is bottomed. 2. Slip nut and sleeve over tube. 3. Insert tubing in fitting body as far as it will go and tighten nut until stop is reached. The elastic sleeve ordinarily will extrude slightly around the tube at the end of the nut. This extrusion further aids in isolating the tube from the nut. FLEX FLRELESS TUE FITTINGS PRESSURE HRT FITTING TUING MTERIL: RSS MTERIL: LL TYPES REOMMENDED MX MUM WORKING PRESSURE (PSI) Service Tube O.D. Tubing ll Tubing onditions (Inches) Not elled* elled Static Pressure 1/8 1,000 2,000 3/16 750 1,500 Very Minor 1/4 500 1,000 Surges 5/16 450 900 3/8 350 700 Minor 1/2 200 500 Line Vibration 5/8 400 3/4 350 7/8 300 Static Pressure 1/8 800 1,600 3/16 600 1,200 Minor Surges 1/4 400 800 5/16 325 700 Severe 3/8 225 500 Vibration 1/2 150 375 5/8 300 3/4 250 7/8 200 To ssemble (ontinued) Figure1 Tube Length alculator This table shows distance tube extends beyond face of Flex fitting body on installation with bell on tubing and without bell on tubing. With ell Less ell Tube O.D. With ell Without ell (Inches) (Inches) (Inches) 1/8 3/16 3/16 3/16 3/16 7/32 1/4 3/16 1/4 5/16 3/16 1/4 3/8 3/16 1/4 1/2 3/16 1/4 5/8 3/16 Tubing should be belled. 3/4 3/16 Tubing should be belled. 7/8 1/4 Tubing should be belled. Very Severe 1/8 600 1,200 Vibration 3/16 450 900 1/4 300 600 Minor Tube 5/16 225 500 Movement 3/8 175 400 1/2 100 250 Mechanical 5/8 200 Shock 3/4 150 7/8 100 Nut Tubing ell c *Where high application pressures are involved, and on all sizes larger than 1/2 O.D., the end of the tube should be slightly belled. How to assemble for higher pressure applications: 1. onsult pressure chart to determine if tubing should be belled for your particular application. 2. Slip the nut and sleeve over tubing. The sleeve should be positioned near end of tubing just behind the surface to be belled. 3. ell tubing with standard 45 flaring tool or 90 punch. The size of bell should be that shown in Figure 2. Figure 2 Recommended Size of ell Tube O.D. ell Dia. Tube O.D. ell Dia. (Inches) (Inches) (Inches) (Inches) 1/8.190-.160 1/2.569-.539 3/16.255-.225 5/8.694-.664 1/4.318-.288 3/4.819-.789 5/16.381-.351 7/8.944-.914 3/8.444-.414 9
Hi-Seal Design Features ompact design saves space. butt-joint type design and freedom from flaring permit bends to be made exceptionally close to the tube end. In areas where space is limited, tubing must extend through the sleeve but exact placement of tubing in the fitting is not critical. vailable in a variety of metals, styles and sizes. Hi-Seal variety allows you to specify one product to complete the entire job. hoose from brass, steel, stainless steel, and more. Meets low and high pressure applications. Hi-Seal fittings are recommended for low or high pressure service within the safe pressure ranges of the most commonly used types of commercially available tubing. 10 Fitting is tight when threads are out of sight. No tube marking or disassembly needed to assure proper make-up. Positive tubing support on both sides of gripping teeth absorbs shock, vibration and tube movement. Seal maintained even under abusive or vibrating service. Reserve gripping power of second gripping tooth provides fresh seal on every remake. Positive seal maintained, even after repeated disassembly, without tubing constriction. Hi-Seal design prevents locked-in nut because body threads are not deformed outwardly. lways easy to disassemble when necessary. Hi-Seal Fittings can be used on varying wall thickness tubing with unvarying results. Safety margin insures tight joint even without exact placement of tubing in fitting. Even tubing not squarely cut off will hold tight. ontrolled bite does not deform tubing and constrict flow; yet Hi-Seal holds to burst pressures of tubing. One-piece, collared sleeve. Tube supports on both sides of sealing area hold tubing and absorb shock and vibration. Performance in vacuum applications. Independent lab tests of Hi-Seal fittings indicate no leakage when tested by means of a mass spectrometer leak detector, adjusted to indicate a leakage rate of 1.0 x 10-10 standard cubic centimeters of helium per second. Designed for high temperatures. Hi- Seal fittings meet the following temperature limitations for tubing systems: 800 F with stainless steel 425 F with copper and brass 600 F with steel Exceeds vibration and shock standards. Hi-Seal fittings far exceed the minimum requirement of 10,000,000 cycles of vibration required under Military Specification MIL-F-18280E. Hi-Seal fittings permit overhang deflection because the sleeve gives positive tubing support on both sides of the seal with the tube. Pivot points are eliminated the cause of failure in many fittings. Handles repeated assembly. Military Specification MIL-F-18280E also requires that a fitting connection be taken apart and remade a minimum of eight times. Imperial Eastman engineering standards specify a minimum of TWIE the number of remakes required by military specifications. The reserve gripping action of Hi- Seal fittings permits the fitting to exceed this minimum, while still remaining free from leakage. Meets industry s conformance.those conformances include: JI Pneumatic and Hydraulic Standards NSI ode for Pressure Piping SME ode* for Pressure Piping DNV**. (Det Norske Veritas rules for classification of steel ships and mobile offshore units.) MIL.** onforms to MIL-F-18280E and MIL-F-18866G NFP. Manufactured in accordance with NFP recommended standard numbers T3.8.70.2, T3.8.3R2-1977 and T3.8.9-1976. * **Performance standard only. Not dimensionally interchangeable. Temperature ratings given for non-o-ring connectors.
Eliminates welded connections. Say goodbye to welded connections! The raze-seal fitting solves the problems of tubing installations which demand absolute reliability under very high pressures, vacuum, higher temperatures, cryogenics and vibration applications which formerly required welded connections. That s because raze-seal sleeves contain a special silver alloy brazing ring. This sleeve does not have gripping serrations like the standard Hi-Seal sleeve. The raze-seal sleeve is placed over the end of the tube and heated, causing the ring of brazing alloy to flow and form a tough, lasting bond between the tube and the sleeve. The raze-seal sleeve and nut are then assembled to the standard Hi-Seal fitting body. Same performance as Hi-Seal connections! This fitting assembly offers all the advantages of the standard Hi-Seal fittings, including its ability to be repeatedly disconnected and reassembled without loss of original reliability. ssembly advantages. The raze- Seal fitting is more compact, economical and easier to install than any other fitting made for very high pressure, high and low temperature service. raze-seal fittings require minimum tube preparation. No machining of the tube is necessary. Tube need only be cleaned and fluxed. The easy brazing operation is far faster and cleaner than welded joints. Reliability for critical installations. The porosity which can occur in a welded joint is eliminated in a raze-seal connection. The brazing ring was especially developed to give 100% coverage, providing a completely reliable connection. raze-seal fittings eliminate contamination of the system and the need for stress relieving which can be caused by welded connections. raze-seal fittings can be readily inspected for cleanliness before assembly. They allow for correction of installation errors by reheating and removing the sleeve. ll of these features eliminate the hazards of a permanently brazed or welded non-threaded connection. raze-seal fittings will hold high and low pressure volatiles and other fluids where zero leakage is required. These fittings are excellent for cryogenic applications where nitrogen, hydrogen or helium must be conducted under zero leakage conditions. These fittings have been used with complete success on applications which caused every other conventional connecting method to fail. raze-seal sleeves contain a special silver alloy brazing ring raze-seal Design Features raze-seal reducing sleeves connect any body size to a smaller tube O.D. size. n important advantage of a raze-seal fitting is that tubing of a smaller diameter can be connected to any specified fitting body sleeve. (Jump size connections can be made). This feature is extremely convenient on tees, for example, where any smaller size tube can be connected to the same tee body. raze-seal reducing sleeves are used with the standard raze- Seal nuts and Hi-Seal bodies. typical raze-seal reducing sleeve. 11
Hi-Seal Maximum Working Pressures FITTING MTERIL: TUING MTERIL: 12 Steel Steel, SE 1010, Dead Soft, old Drawn and razed Steel ommercially vailable Tubing Wall Thicknesses Maximum Recommended Working Pressure (PSI) Seamless Steel, SE 1010, razed Steel Tube Dead Soft, old Drawn* (Such as undy or GM) Service O.D. onditions (In.).028.035.049.065.083.095.109.120.028.035.049 1/8 6050 7560 6050 3/16 4180 5050 7060 4180 7160 1/4 3350 3800 6210 3350 3800 6210 5/16 2630 3340 5190 2630 3340 4850 3/8 1440 2760 3960 5430 7100 2160 2760 3960 1/2 2020 2900 3940 5160 6000 6980 7750 2020 2900 4-to-1 5/8 2280 3100 4040 4680 5450 6070 2280 Safety 3/4 1880 2540 3310 3840 4460 5370 Factor 7/8 1610 2150 2800 3240 3760 4190 1 1390 1860 2430 2810 3260 3620 1 1/4 1470 1920 2200 2560 3060 1 1/2 1210 1580 1820 2120 2320 1/8 4040 5110 4040 3/16 2790 3360 4700 2790 1/4 2240 2530 4070 2240 2530 4070 5/16 1750 2230 3450 1750 2230 3240 3/8 960 1840 2740 3620 4740 1440 1840 2740 1/2 1350 1930 2630 3440 4000 4650 5160 1350 1930 6-to-1 5/8 1520 2060 2690 3120 3630 4050 1520 Safety 3/4 1250 1690 2200 2560 2980 3550 Factor 7/8 1070 1440 1870 1260 2500 2800 1 920 1240 1620 1870 2180 2410 1 1/4 980 1280 1470 1710 2020 1 1/2 800 1050 1220 1410 1550 1/8 3030 3780 3030 3/16 2090 2530 3530 2090 1/4 1680 1900 3110 1680 1900 3110 5/16 1320 1670 2590 1320 1670 2420 3/8 720 1380 1980 2660 3650 1080 1380 1980 1/2 1010 1450 1970 2580 3000 3490 3880 1010 1450 8-to-1 5/8 1140 1550 2020 2340 2720 3040 1140 Safety 3/4 940 1270 1660 1920 2230 2660 Factor 7/8 805 1080 1400 1620 1880 2100 1 700 930 1220 1400 1630 1810 1 1/4 735 960 1100 1280 1520 1 1/2 605 780 910 1060 1160 1/8 2420 3070 2420 3/16 1670 2020 2820 1670 1/4 1340 1520 2490 1340 1520 2490 5/16 1050 1340 2080 1050 1340 1940 3/8 575 1110 1580 2170 2840 865 1110 1580 1/2 805 1160 1580 2060 2400 2790 3100 805 1160 10-to-1 5/8 910 1240 1620 1870 2180 2430 910 Safety 3/4 745 1020 1330 1540 1790 2130 Factor 7/8 590 860 1120 1300 1510 1680 1 555 745 970 1120 1300 1450 1 1/4 589 765 880 1020 1220 1 1/2 485 630 725 850 925 *bove pressures are based on the use of steel Hi-Seal fittings with SE 1010 steel tubing. Higher pressures may be obtained with certain other high strength steel tubing. heck with factory for pressure limitations on type of tubing being used. Note: 1. Working pressure based on room temperature (72 F) service. For elevated temperature service, multiply these pressures by derating factors obtained from chart on page 17. 2. Fittings with tapered pipe threads (NPT or NPTF) may have pressure capabilities limited to that of the pipe threads. Such fittings should not be used at pressures exceeding those listed on page.
FITTING MTERIL: Type 316 bodies and nuts with 17-4 PH Sleeves or Stainless Steel Type 316 assemblies with Type 316 Sleeves TUING MTERIL: nnealed Stainless Steel, Type 304 Hi-Seal Maximum Working Pressures ommercially vailable Tubing Wall Thicknesses Maximum Recommended Working Pressure (PSI) Type 316 ssemblies Type 316 ssemblies 17-4 PH Sleeves 316 Sleeved (Welded or Seamless Tubing, (Seamless Tubing, Hardness Tube Hardness Rockwell 90 Maximum) Rockwell 90 Maximum) Service O.D. onditions (In.).028.035.049.065.083.095.109.120.028.035.049.065 1/8 8180 10200 8180 10200 3/16 5650 6820 9710 5650 6820 9710 1/4 4520 5900 8400 4520 5900 8400 3/8 2920 3900 5500 7250 2920 3900 5500 7250 1/2 2150 3000 4100 5500 6980 8100 9430 1050 2150 3000 4100 5500 4-to-1 5/8 1710 2400 3300 4400 5450 6310 7360 8200 1710 2400 3300 4400 Safety 3/4 2700 3600 4470 5170 6020 6700 2700 3600 Factor 1 1870 2510 3270 3790 4380 4820 1400 1400 1 1/4 1470 1980 2580 2970 3420 3760 1 1/2 1220 1640 2130 2460 2840 3130 1/8 5450 6800 5450 6800 3/16 3770 4500 6470 3770 4550 6470 1/4 3020 3940 5700 3020 3940 5700 3/8 1950 2700 3670 4840 1950 2700 3670 4840 1/2 1430 2000 2740 3660 4650 5400 6290 7000 1430 2000 2740 3660 6-to-1 5/8 1140 1600 2200 2940 3610 4210 4910 5470 1140 1600 2200 2940 Safety 3/4 1800 2400 2980 3450 4010 4460 1800 2400 Factor 1 1250 1670 2180 2530 2930 3210 925 925 1 1/4 980 1320 1720 1980 2280 2510 1 1/2 814 1100 1420 1640 1900 2090 1/8 4090 5100 4090 5100 3/16 2830 3410 4860 2830 3410 4860 1/4 2260 2950 4200 2260 2950 4200 3/8 1460 1950 2750 3630 1460 1950 2750 3630 1/2 1080 1500 2050 2750 3490 4050 4720 5250 1080 1500 2050 2750 8-to-1 5/8 855 1200 1650 2200 2740 3160 3680 4100 855 1200 1650 2200 Safety 3/4 1350 1800 2240 2580 3010 3350 1350 1800 Factor 1 935 1260 1640 1900 2200 2410 700 700 1 1/4 735 990 1290 1490 1710 1880 1 1/2 610 820 1070 1230 1420 1570 1/8 3270 4080 3270 4080 3/16 2260 2730 3890 2260 2730 3890 1/4 1810 2360 3360 1810 2360 3360 3/8 1170 1560 2200 2900 1170 1560 2200 2900 1/2 860 1200 1640 2200 2790 3240 3770 4200 860 1200 1640 2200 10-to-1 5/8 685 960 1320 1760 2180 2530 2950 3280 685 960 1320 1760 Safety 3/4 1080 1440 1780 2070 2410 2680 1080 1440 Factor 1 795 1000 1310 1520 1760 1930 550 550 1 1/4 585 790 1030 1190 1370 1500 1 1/2 485 655 850 980 1100 1250 Note: 1. Working pressure based on room temperature (72 F) service. For elevated temperature service, multiply these pressures by derating factors obtained from chart on page 17. 2. Fittings with tapered pipe threads (NPT or NPTF) may have pressure capabilities limited to that of the pipe threads. Such fittings should not be used at pressures exceeding those listed on page. 13
Hi-Seal Maximum Working Pressures FITTING MTERIL: Stainless Steel, Type 316, bodies and nuts with 17-4 PH Sleeves TUING MTERIL: 1/8 Hard Stainless Steel, Type 304 (Hardness Rockwell 25 Maximum) ommercially vailable Tubing Wall Thicknesses Maximum Recommended Working Pressure (PSI) Tube Service O.D. onditions (In.).028.035.049.065.083.095.109.120 1/8 13400 16800 3/16 9300 11200 15700 1/4 7440 9500 13800 3/8 4800 6110 8820 12000 1/2 3520 4500 6450 8760 11500 13400 15600 4-to-1 5/8 2820 3540 5160 6970 8960 10400 12100 13500 Safety 3/4 2310 2940 4170 5660 7350 8520 9930 11000 Factor 1 1740 2160 3090 4140 4500 1 1/4 1740 2430 3270 4250 1-1/2 1440 2010 2700 3510 1/8 8940 11200 3/16 6200 7460 10500 1/4 4950 6330 9200 3/8 3200 4070 5880 8000 1/2 2340 3000 4300 5840 7660 8930 10400 6-to-1 5/8 1880 2360 3440 4550 5970 6940 8060 9000 Safety 3/4 1540 1960 2780 3780 4900 5680 6610 7340 Factor 1 1160 1440 2060 2760 3000 1 1/4 1160 1620 2180 2840 1 1/2 960 1340 1800 2340 1/8 6700 8400 3/16 4650 5600 7850 1/4 3720 4750 6900 3/8 2400 3060 4410 6000 1/2 1710 2750 3230 4380 5750 6700 7800 8-to-1 5/8 1410 1770 2580 3990 4480 5200 6050 6750 Safety 3/4 1170 1470 2080 2840 3680 4260 4950 5500 Factor 1 870 1080 1550 2070 2250 1 1/4 870 1220 1640 2120 1 1/2 720 1010 1350 1760 1/8 5360 6720 3/16 3720 4480 6280 1/4 3960 3800 5720 3/8 1920 2440 3520 4800 1/2 1410 1800 2680 3510 4600 5360 6240 10-to-1 5/8 1130 1420 2060 2790 3590 4160 4840 5400 Safety 3/4 925 1180 1640 2270 2940 3410 3970 4400 Factor 1 695 865 1240 1660 1800 1 1/4 695 972 1310 1700 1 1/2 575 805 1080 1410 Note: 1. Working pressure based on room temperature (72 F) service. For elevated temperature service, multiply these pressures by derating factors obtained from chart on page 17. 2. Fittings with tapered pipe threads (NPT or NPTF) may have pressure capabilities limited to that of the pipe threads. Such fittings should not be used at pressures exceeding those 14
FITTING MTERIL: TUING MTERIL: rass opper, Dead Soft, Seamless Hi-Seal Maximum Working Pressures ommercially vailable Tubing Wall Thicknesses Maximum Recommended Working Pressure Tube (PSI Service O.D. onditions (In.).028.032.035.042.049.065.083 1/8 3710 4480 5000 3/16 2710 2990 3300 3920 4580 1/4 2170 2250 2500 3400 4030 5/16 1710 1800 2000 2640 3120 3/8 1400 1500 1650 2170 2580 3520 4-to-1 1/2 1030 1150 1250 1590 1890 2560 3360 Safety 5/8 935 1000 1250 1400 1800 2520 Factor 3/4 850 1030 1150 1500 2140 7/8 885 1030 1390 1810 1 900 1210 1580 1/8 2470 2980 3/16 1810 1990 2200 2620 3060 1/4 1450 1500 1670 2260 2680 5/16 1140 1200 1330 1630 2080 3/8 930 1000 1100 1450 1720 2340 6-to-1 1/2 685 765 830 1060 1260 1710 2240 Safety 5/8 625 665 833 930 1200 1680 Factor 3/4 565 685 765 1000 1430 7/8 589 685 925 1210 1 600 805 1050 FITTING MTERIL: TUING MTERIL: rass opper, Half Hard, Seamless ommercially vailable Tubing Wall Thicknesses Maximum Recommended Working Pressure Tube (PSI) Service O.D. onditions (In.).028.032.035.042.049.065.083 1/8 4210 5100 5700 3/16 3080 3400 3750 4450 5200 1/4 2470 2560 2840 3860 4580 5/16 1940 2040 2280 3000 3570 3/8 1170 1710 1880 2470 2940 4000 4-to-1 1/2 1310 1420 1810 2150 2910 3820 Safety 5/8 1070 1140 1420 1590 2050 2860 Factor 3/4 965 1170 1310 1710 2440 7/8 1000 1170 1580 2060 1 1030 1380 1800 1/8 2800 3390 3780 3/16 2060 2260 2500 2980 3480 1/4 1650 1710 1900 2570 3270 5/16 1300 1370 1510 1850 2360 3/8 1110 1140 1250 1650 1960 2660 6-to-1 1/2 820 915 995 1210 1430 1940 2550 Safety 5/8 745 795 995 1110 1360 1910 Factor 3/4 675 815 915 1140 1630 7/8 700 815 1110 1380 1 715 965 1190 Note: 1. Working pressure based on room temperature (72 F) service. For elevated temperature service, multiply these pressures by derating factors obtained from chart on page 17. 2. Fittings with tapered pipe threads (NPT or NPTF) may have pressure capabilities limited to that of the pipe threads. Such fittings should not be used at pressures exceeding those listed on page. 15
Hi-Seal Maximum Working Pressures PIPE THRED ENDS Pipe Pipe thread ends Maximum Recommended Working Pressures Service Size (PSI) onditions (In.) Fitting ody Material Type 316 rass arbon Steel Stainless Steel 1/4 4000 5000 5000 3/8 3000 4500 5000 4-to-1 1/2 2000 4000 4000 Safety 3/4 1750 3000 3000 Factor 1 1500 2250 2500 1/4 2650 3350 3350 3/8 2000 3000 3350 6-to-1 1/2 1325 2650 2650 Safety 3/4 1150 2000 2000 Factor 1 1000 1500 1675 1/4 2000 2500 2500 3/8 1500 2250 2500 8-to-1 1/2 1000 2000 2000 Safety 3/4 875 1500 1500 Factor 1 750 1125 1250 1/4 1600 2000 2000 3/8 1200 1800 2000 10-to-1 1/2 800 1600 1600 Safety 3/4 700 1200 1200 Factor 1 600 900 1000 Note: 1. Fittings with tapered pipe ends (male or female) are not recommended if system pressure exceeds these values. 2. Some codes may set lower limits than are indicated here. 3. Refer to previous charts for maximum tube working pressures based on material and on all thickness which may lower values of the above. raze-seal Maximum Working Pressures FITTING MTERIL: TUING MTERIL: Type 316 Stainless Steel 316 Stainless Steel Tube Maximum Recommended Service O.D. Working Pressures onditions (In.) (PSI) 1/4 19,250 ased On 3/8 16,000 80% raze 1/2 15,600 overage 9/16 15,400 5/8 15,400 4-to-1 3/4 15,000 Safety 7/8 14,000 Factor 1 13,000 1 1/4 12,000 1 1/2 11,000 Note: 1. These maximum ratings, which are based on a 4-to-1 safety factor, apply to the brazed connection only. ctual installations must be derated to allow for tube strength, other style ends (if any), fitting body strength and elevated temperatures. 2. It is recommended that tubing with an O.D. of nominal to plus tolerance be used to provide optimum clearance for the brazed joint. 3. Working pressure based on room temperature (72 F) service. For elevated temperature service, multiply these pressures by derating factors obtained from chart on page 17. 4. Fittings with tapered pipe threads (NPT or NPTF) may have pressure capabilities limited to that of the pipe threads. Such fittings should not be used at pressures exceeding those listed on page. 16
FITTING MTERIL: TUING MTERIL: arbon Steel arbon Steel raze-seal Maximum Working Pressures Tube Maximum Recommended Service O.D. Working Pressures onditions (In.) (PSI) 1/4 15,000 ased On 3/8 12,000 80% raze 1/2 11,700 overage 9/16 5/8 11,500 3/4 11,250 7/8 10,500 1 9,700 1 1/4 9,000 1 1/2 8,200 Note: 1. These maximum ratings, which are based on a 4-to-1 safety factor, apply to the brazed connection only. ctual installations must be derated to allow for tube strength, other style ends (if any), fitting body strength and elevated temperatures. 2. It is recommended that tubing with an O.D. of nominal to plus tolerance be used to provide optimum clearance for the brazed joint. 3. Working pressure based on room temperature (72 F) service. For elevated temperature service, multiply these pressures by derating factors obtained from chart on page 17. 4. Fittings with tapered pipe threads (NPT or NPTF) may have pressure capabilities limited to that of the pipe threads. Such fittings should not be used at pressures exceeding those listed on page. DERTING FTORS for Elevated Temperature pplications for Hi-Seal Hi-Seal & raze-seal Derating Factors DERTING FTORS for Elevated Temperature pplications for raze-seal 1.00 1.00 TEMPERTURE DERTING FTOR.90.80.70.60.50.40.30 RSS RON STEEL TYPE 316 STINLESS STEEL TEMPERTURE DERTING FTOR.90.80.70.60.50.40.30.20.20.10.10 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 WORKING TEMPERTURE F 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 WORKING TEMPERTURE F PRESSURE RTING PROEDURE FOR HI-SEL & RZE-SEL FITTINGS 1. For applications involving service at elevated temperatures the pressure rating must be multiplied by an appropriate temperature derating factor obtained from the temperature derating chart above. 2. arbon Steel fittings not normally recommended above 600 F. 3. 316 Stainless Steel fittings not normally recommended above 800 F. 4. These working pressures are not necessarily valid for system components other that raze- Seal fitting ends. Prudent system design requires that all other system components be evaluated for their specific proper pressure capabilities. 17
Hi-Seal ssembly Instructions Male and Female Pipe Thread SE Straight Thread Port, ack-up Washer and Lock Nut General Information Port Sealing Methods Hi-Seal fittings are furnished with two types of port connections: 1. NPTF Tapered Pipe Threads. arbon steel, stainless steel, and brass fittings are supplied with dryseal threads, which meet all the appropriate requirements of SE standards. Fitting bodies are machined with dryseal threads, which are designed to assure better thread contact and to prevent spiral leakage. The length of dryseal pipe threads is highly valuable when reconnecting. It allows for further takeup; and in combination with the thread form, gives a tighter joint with less chance of leakage. 2. Straight Thread O-Ring Seal. For connecting into ports of hydraulic valves and other parts, the O-ring seal offers the following advantages. It eliminates the possibility of broken fittings, deformed housings, and cracking of ports which can result from over-torquing with pipe threads. n O-ring seal also lets you position elbows and tees so that tube ends will always be in proper alignment. Hi-Seal elbows and tees with straight thread O-ring seal have a back-up washer crimped into position in the O-ring groove ahead of the lock nut. This washer prevents the O-ring from extruding into threads when the joint is under pressure. When specifying O-rings, they must be of a compound compatible with the fluid in the system. ssembly Instructions for Fittings with Straight Thread O-Ring Seal 1. Turn the locknut as far back on the fitting as is possible. Lubricate O-ring by coating with a light oil or petrolatum and position to the extreme rear of the O-ring groove. 2. Turn the locknut down until it just contacts the back-up washer. 3. Holding the fittings and the locknut in position, screw the fitting into the straight thread boss until the back-up washer just contacts the face of the boss. 4. Position the fitting by turning the fitting out (counter clockwise) up to 359 and tighten the locknut. 5. On a Hi-Seal connector the hex on the body takes the place of the locknut. Screw fully into straight thread boss and tighten hex against face of boss. ody Hex Nut ack-up Washer O-Ring ssembly Instructions for djustable Fittings 1. Turn the locknut as far back on the fitting as is possible. Lubricate O-ring by coating with a light oil or petrolatum and position to the extreme rear of the O- ring groove. 2. Turn the locknut down until it just contacts the backup washer. 3. Holding the fittings and the locknut in position, screw the fitting into the straight thread boss until the back-up washer just contacts the face of the boss. 4. Position the fitting by turning the fitting out (counter clockwise) up to 360 and tighten the locknut. 5. On a Hi-Seal connector the hex on the body takes the place of the locknut. Screw fully into straight thread boss and tighten hex against face of boss. 18
Hi-Seal ssembly Instructions Nut Sleeve Teeth in sleeve grip tube. Short heavy end ody e sure threads are completely covered by the nut. Figure 1 Figure 2 Figure 3 Figure 4 Hi-Seal ssembly Instructions 1. For best results. lways use a fitting whose materials are compatible with the tubing that is used. (e.g when using stainless steel tubing, use 316 stainless steel fittings). This will minimize the possibility of chemical or galvanic corrosion.. Keep in mind that the sleeve should always have a hardness at least equal to that of the tubing used. Type 316 sleeves may be used with seamless annealed stainless steel tubing.. When assembling fittings to both ends of a length of tubing, partly tighten the nut at one end until the tube cannot be turned by hand; then fully tighten the fitting at the other end until the threads are completely covered. Finally, finish tightening the first end until those threads are completely covered. 2. Preparation of Tubing. ut tubing with a tube cutter or a hacksaw with a fine tooth blade and a sawing vise.. Deburr inside and outside of tubing sufficiently to remove burrs to assure that sleeve will slip freely onto the tube. 3. ssembly.. Lubricate the threads and the camming area of the nut with a lubricant that will be compatible with the system fluid. Lubrication is especially important with stainless steel assemblies.. Slide nut onto tubing, place sleeve over end of tube with short, heavy end towards end of tubing (Figure 1). utt tubing end against tubing stop in body (Figure 2).. ssemble nut, sleeve, and tube to body hand tight (Figure 3). D. Tighten nut with a wrench until threads on body are completely covered by the nut as shown in Figure 4. This visual check provides positive assurance of a tight joint. 4. Remake(s). When a Hi-Seal connection is to be reassembled, retighten the Hi- Seal nut 1/6 turn (one hex flat) beyond the previously assembled position. This will properly reseal the connections. Nut Sleeve Presetting tool 700FS Figure 1 Figure 2 Figure 3 Figure 4 Presetting Instructions for Hi-Seal Fittings Normally it is not necessary to preset Hi-Seal fittings. Presetting is ordinarily used only where adequate torque cannot be applied at point of installation due to space restrictions, or for pre-production assembly. For these cases, special presetting tools are available. In an emergency, a fitting body may be used as a presetting tool. 1. Preparation of Tubing. ut tubing with a tube cutter or a hacksaw with a fine tooth blade and a sawing vise.. Deburr inside and outside of tubing sufficiently to remove burrs and to assure that sleeve will slip freely onto the tube. 2. Presetting. Select the proper size presetting tool.. Lubricate the threads and the camming area of the nut with a lubricant that will be compatible with the system fluid.. Slide nut onto tubing and place sleeve over end of tube with short, heavy end facing toward end of tubing as shown in Figure 1. utt tubing end against tubing stop in tool. D. ssemble nut, sleeve and tube to presetting tool hand tight as shown in Figure 2. E. Tighten nut with a wrench until threads on presetting tool are covered by the nut as shown in Figure 3. 3. Disassembly and Inspection. Disassemble from presetting tool.. Make sure that: (1) Sleeve has been coined into tubing, leaving a slight concave surface on outside diameter of sleeve. (2) Sleeve does not move longitudinally. (It may rotate on tube). 4. Final ssembly. Install the line in position and finger tighten nut on body of fitting.. Tighten nut until an increased resistance to turning is felt. t this point the nut should completely cover the threads on the body; if not, tighten until it does. See Figure 4. 19
raze-seal ssembly Instructions Tube O.D. Size (In.) 1/4 3/8 1/2 5/8 3/4 7/8 1 1 1/4 1 1/2 Typical ssembly Torque (Pounds-Inch) 600-650 750-800 825-875 875-925 1100-1175 1150-1225 1250-1350 1475-1575 1725-1825 Fitting Ready for razing fter razing and ssembly General Information To produce a satisfactory brazed joint, certain precautions must be taken. The parts to be brazed must be very thoroughly cleaned so that all scale, oxides, grease, oil, dirt and other foreign materials are removed. proper, silver brazing flux must be used. These fluxes are fluid and active at the flow point of the brazing alloy. (Note that sleeve is furnished with silver brazing ring.) Flux should be applied evenly to both the inside and outside of sleeve and outside of tubing with care so that no bare spots remain. method of applying heat should be used to heat the tube and sleeve uniformly. When heating with an oxy-acetylene torch, a tip sufficiently large with a soft neutral or slightly reducing flame should be used to give the necessary heat. s a general rule, best results are obtained when the joint is heated rapidly and kept at the brazing temperature for the minimum time required for proper flowing of the alloy. Resistance heating is acceptable; however, the current must be kept low enough to prevent severe burning at the contact points. raze-seal ssembly Instructions 1. Preparation of Tubing. ut tubing squarely with a tube cutter or a hacksaw with a fine tooth blade and a sawing vise. Deburr inside and outside of tubing to remove burrs and to assure that sleeve will slip freely onto the tube. Inspect tube end for surface imperfections and ovality on the outer circumference. Make sure it conforms to tolerances and meets requirements of applicable specifications. 2. ssembly.. lean sleeve (with silver brazing ring intact) and tube with a solvent to remove all oils and dirt. With a piece of emery cloth, polish the outside surface of the tubing end over a two-inch length to remove any metal oxides which may have formed.. Flux the inside of the sleeve, also covering the silver brazing ring, and place sleeve on tube. Flux the outside of the sleeve. Flux the outside of the tube to a point beyond the sleeve depth.. Holding the tube upright if possible, heat tube and sleeve, concentrating the heat on the tube just beyond the sleeve. Slowly move the torch forward toward the far end beyond the sleeve and back to the tube repeatedly until the braze ring begins to melt. Then move the torch to the near end of the sleeve and hold until an even fillet begins to form. When fillet is formed, remove the torch. t the flow temperature of the brazing alloy, the tube and sleeve should have a dull red color. While the alloy is still fluid, lightly press the sleeve down so that it abuts the end of the tubing. Push the sleeve all the way onto the tubing. Use a wood block or similar object to avoid damage. D. ny excess brazing alloy that runs down the tubing or flows on the seating surface of the sleeve should be wiped off before the alloy solidifies. llowed the brazed assembly to cool. Then scrub in hot water to remove excess flux. Filing, scratch brush, or emery cloth should not be used to clean excess alloy from the precision seating surface of the sleeve, as scratch marks or flat spots will cause leakage. E. ssemble the fitting by tightening the nut. Lubricate the threads and the seat area of the body with an acceptable lubricant that will be compatible with the system fluid. ssemble fitting, using the recommended typical assembly torque values shown above. Remake(s). When fittings are disassembled, retighten to the original tightness or makeup. 20
Hi-Seal Ordering Information EXMPLE: Type of Fitting Tube O.D. Size 768FSS 06X04 To order Hi-Seal fittings, one of the following suffix letters must be added to the catalog number to indicate the metal desired: S Steel. (Low arbon) Elbows and tees are close grain forgings. SS Stainless Steel (316) Material (Stainless Steel) rass Pipe Size The size designation must also be included with the catalog number. 1. EXMPLE: When specifying connector 768F in stainless steel, with 3/8 O.D. tube connection and 1/4 male pipe thread. This should be written: No. 768FSS06X04. 2. EXMPLE: No. 768FSO06 would specify a steel connector for 3/8 O.D. tube with straight thread O-ring port seal on other end. When fittings with O-ring port seal are desired, this specification must also be included in the catalog number. The letter O following the number indicates O-ring. Materials for Standard Hi-Seal Fittings RSS FITTINGS Elbows and Tees: rass forgings S..E. 377. onnectors, Unions, Sleeves and Nuts: Stress relieved brass bar stock S..E. 360 or equivalent. STEEL FITTINGS Elbows and Tees: lose grained steel forgings S..E. 12L14 or equivalent. onnectors, Unions and Nuts: Steel bar stock S..E. 12L14 or equivalent. Sleeves: Steel bar stock S..E. -1144, stress relieved, black phosphate finish. odies and Nuts are furnished with zinc plate finish as standard. (Dry film lubricant finish standard on 5/8 nuts and larger.) lack phosphate finish can be obtained on a special order. STINLESS STEEL FITTINGS Elbows and Tees: Stainless steel forgings Type 316. onnectors and Unions: Stainless Steel bar stock Type 316. Nuts: Stainless steel bar stock Type 316. Dry film lubricant finished to provide lubricant for facilitating assembly. Sleeves: Stainless steel bar stock Type 316. Type 17-4PH is optional. 21
raze-seal Ordering Information EXMPLE: Sleeve raze-seal Sleeve 760FSSZ06 How to Specify and Order raze-seal Fittings ny Hi-Seal steel or stainless steel fittings can be converted to an extra-reliable raze-seal fitting by replacing the Hi-Seal nut and sleeve with the raze-seal nut and sleeve. Material (Stainless Steel) Sleeve Size raze-seal Presetting Tool Hi-Seal Presetting Tool Made of hardened stainless steel. For presetting Hi-Seal fittings. Presetting is ordinarily used only when adequate torque cannot be applied at point of installation due to space restrictions, or for pre-production assembly. Part No. 700FS04 700FS06 700FS08 Maintenance of Presetting Tool Handle presetting tools with care, being sure that the threads and 12 seat are not nicked or in any way damaged. Do not attempt to rework took if it becomes damaged obtain a new tool. Keep tools stored so that they will not be damaged. Seal-peel dip or a similar protective coating that is used for gauges and tools is recommended. 22
Poly-Flo Flareless Tube Fittings Material: rass Wrench Part Tube Pipe Pad/Hex Style No. O.D. Thread STYLE 31PG Spring Guard For use with 261-PG and 261-UG nuts. 31PG04 1 /4 3.000 31PG05 5 /16 3.000 31PG06 3 /8 3.000 31PG08 1 /2 3.000 STYLE 256P Reducing Union 256P06X04 3 /8 x 1 /4 1.187.718.500 STYLE 259P ap 259P04 1 /4.500 259P05 5 /16.531 259P06 3 /8.562 259P08 1 /2.593 STYLE 260P Plastic Sleeve 260P04 1 /4.325 260P05 5 /16.347 260P06 3 /8.356 260P08 1 /2.409 23
Tube Fittings Poly-Flo Flareless Material: rass Wrench Part Tube Pipe Pad/Hex Style No. O.D. Thread STYLE 260U oupling Sleeve 260U06 3 /8 260U08 1 /2 STYLE 260U Universal rass Sleeve 260U02 1 /8.359 260U03 3 /16.328 260U04 1 /4.266 260U05 5 /16.266 260U06 3 /8.296 260U08 1 /2.359 STYLE 261P Nut and Plastic Sleeve ssembly 261P04 1 /4.343.437 261P05 5 /16.343.500 261P06 3 /8.375.562 261P08 1 /2.421.812 STYLE 261PG Nut and Plastic Sleeve ssembly For use with Spring Guard 261PG04 1 /4.625.437 261PG05 5 /16.625.500 261PG06 3 /8.656.562 261PG08 1 /2.719.812 24
Tube Fittings Poly-Flo Flareless Material: rass Wrench Part Tube Pipe Pad/Hex Style No. O.D. Thread STYLE 261U Nut Only 261U02 1 /8.375.375 261U03 3 /16.406.437 261U04 1 /4.343.437 261U05 5 /16.343.500 261U06 3 /8.375.562 261U08 1 /2.421.812 STYLE 261U Universal Nut and rass Sleeve ssembly 261U01 1 /16.375.312 261U02 1 /8.375.375 261U03 3 /16.406.437 261U04 1 /4.343.437 261U05 5 /16.343.500 261U06 3 /8.375.562 261U08 1 /2.421.812 STYLE 261UG Nut Only For use with spring guard and 260-U sleeve. 261UG04 1 /4.625.437 261UG05 5 /16.625.500 261UG06 3 /8.656.562 261UG08 1 /2.718.812 STYLE 262P Union 262P02 1 /8 1.156.656.312 262P03 3 /16 1.250.750.375 262P04 1 /4 1.125.687.375 262P05 5 /16 1.156.687.437 262P06 3 /8 1.218.718.500 262P08 1 /2 1.343.843.687 25
Tube Fittings Poly-Flo Flareless Material: rass Wrench Part Tube Pipe Pad/Hex Style No. O.D. Thread STYLE 262P Union Poly-Flo to Standard ompresamatic 262P04 1 /4 1.250.750.437 262P06 3 /8 1.406.843.562 STYLE 262PH Union Poly-Flo to Hi-Duty 262PH04 1 /4 1.468.875.562 262PH06 3 /8 1.625.968.625 STYLE 262PHS Union Poly-Flo to Hi-Seal 262PHS04 1 /4 1.594.812.500 STYLE 264P Union Tee 264P02 1 /8.875.625.312 264P03 3 /16.875.625.312 264P04 1 /4.843.625.375 264P05 5 /16.859.625.375 264P06 3 /8.906.656.437 264P08 1 /2 1.062.812.625 26
Tube Fittings Poly-Flo Flareless Material: rass Wrench Part Tube Pipe Pad/Hex Style No. O.D. Thread D STYLE 266P Female onnector 266P02X02 1 /8 1 /8 1.031 0.750 0.562 266P03X02 3 /16 1 /8 1.031 0.781 0.562 266P03X04 3 /16 1 /4 1.218 0.968 0.687 266P04X02 1 /4 1 /8 0.968 0.750 0.500 266P04X04 1 /4 1 /4 1.156 0.937 0.625 266P05X02 5 /16 1 /8 1.000 0.750 0.500 266P06X04 3 /8 1 /4 1.187 0.937 0.625 266P08X06 1 /2 3 /8 1.250 1.000 0.812 STYLE 268P Male onnector 268P02X01 1 /8 1 /16 1.031 0.781 0.375 268P02X02 1 /8 1 /8 1.078 0.796 0.437 268P03X01 3 /16 1 /16 1.093 0.843 0.437 268P03X02 3 /16 1 /8 1.109 0.859 0.437 268P04X01 1 /4 1 /16 1.031 0.812 0.375 268P04X02 1 /4 1 /8 1.031 0.812 0.437 268P04X04 1 /4 1 /4 1.188 1.000 0.562 268P04X06 1 /4 3 /8 1.250 1.031 0.687 268P05X02 5 /16 1 /8 1.046 0.812 0.437 268P05X04 5 /16 1 /4 1.234 1.000 0.562 268P06X02 3 /8 1 /8 1.093 0.843 0.500 268P06X04 3 /8 1 /4 1.281 1.031 0.562 268P06X06 3 /8 3 /8 1.281 1.031 0.687 268P08X06 1 /2 3 /8 1.343 1.093 0.687 268P02X1032 1 /8 10-32* 0.843 0.593 0.375 268P04X1032 1 /4 10-32* 0.968 0.750 0.375 *Part number includes gaskets. STYLE 269P Male Elbow D 269P02X01 1 /8 1 /16 0.875 0.625 0.312 0.688 269P02X02 1 /8 1 /8 0.875 0.625 0.312 0.688 269P03X01 3 /16 1 /16 0.875 0.625 0.375 0.688 269P03X02 3 /16 1 /8 0.875 0.625 0.375 0.688 269P04X01 1 /4 1 /16 1.000 0.781 0.375 0.750 269P04X02 1 /4 1 /8 0.843 0.625 0.375 0.750 269P04X04 1 /4 1 /4 0.875 0.656 0.375 0.937 269P04X06 1 /4 3 /8 0.968 0.750 0.500 1.031 269P05X02 5 /16 1 /8 0.859 0.625 0.406 0.750 269P06X02 3 /8 1 /8 0.875 0.625 0.437 0.750 269P06X04 3 /8 1 /4 0.968 0.718 0.437 0.937 269P06X06 3 /8 3 /8 1.031 0.781 0.500 1.031 269P08X06 1 /2 3 /8 1.031 0.781 0.625 1.156 27
Tube Fittings Poly-Flo Flareless Material: rass Wrench Wrench Part Tube Pipe Pad/Hex Pad/Hex Style No. O.D. Thread D E STYLE 269SP Male Elbow Swivel 1/8 O.D. tube size does not have tube support. D 269SP04X02 1 /4 1 /8 0.812 0.594 0.375 0.862 0.437 269SP04X04 1 /4 1 /4 0.906 0.688 0.562 1.218 0.562 269SP06X02 3 /8 1 /8 0.875 0.625 0.437 0.904 0.437 269SP06X04 3 /8 1 /4 0.937 0.685 0.562 1.218 0.562 269SP06X06 3 /8 3 /8 0.859 0.602 0.562 1.190 0.687 269SP08X06 1 /2 3 /8 1.031 0.782 0.625 1.218 0.687 E STYLE 269LLP Extra Long Male Elbow 269LLP04X04 1 /4 1 /4 0.906 0.687 0.437 1.500 D STYLE 270P Female Elbow 270P02X02 1 /8 1 /8 0.968 0.687 0.562 0.546 270P03X02 3 /16 1 /8 0.968 0.718 0.562 0.546 270P04X02 1 /4 1 /8 0.906 0.625 0.375 0.750 270P04X04 1 /4 1 /4 0.937 0.718 0.500 0.875 270P06X04 3 /8 1 /4 0.968 0.718 0.500 0.875 270P08X06 1 /2 3 /8 1.156 0.906 0.625 0.937 D 28
Poly-Flo Flareless Tube Fittings Material: rass Wrench Part Tube Pipe Pad/Hex Style No. O.D. Thread D STYLE 271P Male Run Tee 271P02X02 1 /8 1 /8 0.906 0.625 0.312 0.687 271P04X02 1 /4 1 /8 0.843 0.625 0.375 0.750 271P04X04 1 /4 1 /4 0.875 0.656 0.375 0.937 271P05X02 5 /16 1 /8 0.859 0.625 0.375 0.750 271P06X04 3 /8 1 /4 0.906 0.656 0.437 0.937 271P08X06 1 /2 3 /8 1.062 0.812 0.625 1.062 D STYLE 272P Male ranch Tee D 272P02X02 1 /8 1 /8 0.906 0.625 0.312 0.687 272P03X02 3 /16 1 /8 0.875 0.625 0.312 0.687 272P04X02 1 /4 1 /8 0.843 0.625 0.375 0.750 272P04X04 1 /4 1 /4 0.875 0.656 0.375 0.937 272P05X02 5 /16 1 /8 0.859 0.625 0.375 0.750 272P06X02 3 /8 1 /8 0.875 0.625 0.438 0.750 272P06X04 3 /8 1 /4 0.906 0.656 0.438 0.937 272P08X06 1 /2 3 /8 1.062 0.813 0.625 1.062 STYLE 277P Female ranch Tee 277P04X02 1 /4 1 /8 0.875 0.656 0.375 0.937 277P04X04 1 /4 1 /4 1.078 0.844 0.562 1.156 277P04X06 1 /4 3 /8 1.078 0.848 0.562 1.250 D 29
Tube Fittings Poly-Flo Flareless Material: rass Wrench Part Tube Pipe ulkhead Pad/Hex Style No. O.D. Thread Thread D STYLE 279P Union Reducing Tee Reducing on ranch 279P06X04 3 /8 x 1 /4 0.968 0.718 0.437 STYLE 282P ulkhead Union 282P04 1 /4 3 /8-24 1.687 1.250 0.562 0.312 282P05 5 /16 7 /16-24 1.718 1.250 0.625 0.312 282P06 3 /8 1 /2-24 1.812 1.312 0.687 0.375 282P08 1 /2 11 /16-20 2.062 1.562 0.875 0.375 D STYLE 282P ulkhead Union Poly-Flo to Standard ompression 282P04 1 /4 3 /8-24 1.796 1.312 0.562 0.325 282P06 3 /8 1 /2-24 2.000 1.437 0.687 0.375 D 30
Poly-Flo Flareless Tube Fittings Material: rass Wrench Part Tube Pipe ulkhead Pad/Hex Style No. O.D. Thread Thread D STYLE 282PT ulkhead Union Straight Through 282PT04 1 /4 3 /8-24 1.218 1.000 0.562 0.312 282PT05 5 /16 7 /16-24 1.234 1.000 0.625 0.312 282PT06 3 /8 1 /2-24 1.312 1.062 0.687 0.375 D STYLE 292P Quick Disconnect Fitting When tube is disconnected, check valve shuts off flow. 292P04X02 1 /4 1 /8 1.093 0.875 0.437 292P04X04 1 /4 1 /4 1.281 1.062 0.562 292P05X02 5 /16 1 /8 1.109 0.875 0.437 292P06X04 3 /8 1 /4 1.343 1.093 0.562 31
Tube Fittings Poly-Flo Flareless Material: rass Wrench Part Tube Pipe Pad/Hex Style No. O.D. Thread STYLE 293P Quick Disconnect Fitting 293P04X04 1 /4 x 1 /4 1.750 1.312 Poly-Flo fitting on one end, other end connects directly to another Poly-Flo fitting. When straight end is disconnected from Poly-Flo fitting, the quick disconnect maintains pressure in the line. STYLE 296P Union Poly-Flo to Solder 296P04X06 1 /4 x 3 /8 1.000 0.781 0.500 296P06X08 3 /8 x 1 /2 1.031 0.781 0.625 STYLE 297P Tube End Reducer 297P06X04 3 /8 x 1 /4 1.718 1.458 0.437 297P08X06 1 /2 x 3 /8 1.875 1.625 0.656 32
Tube Fittings Poly-Flo Kwik-onnect ouplers Material: rass Finish: hrome-plated Wrench Part Tube Pipe ulkhead Pad/Hex Style No. O.D. Thread Thread D STYLE 294P oupler Single End Shut-Off 294P04 1 /4 1 /2-24 2.899 1.718 0.625 294P06 3 /8 11 /16-24 3.461 1.921 0.812 STYLE 294P ody Double End Shut-Off 294P04 1 /4 1 /2-24 1.790 0.625 294P06 3 /8 11 /16-24 1.965 0.812 STYLE 294PD oupler Double End Shut-Off 294PD04 1 /4 1 /2-24 3.180 1.790 0.625 294PD06 3 /8 11 /16-24 3.458 1.965 0.812 STYLE 294PM Insert (Without Shut-Off. Used on double end shut-off models) 294PM04 1 /4 1 /2-24 1.636 0.500 294PM06 3 /8 11 /16-24 1.738 0.500 33
Tube Fittings Poly-Flo Kwik-onnect ouplers Material: rass Finish: hrome-plated Wrench Wrench Part Tube Pipe Pad/Hex Pad/Hex Style No. O.D. Thread D STYLE 294PMD Insert (With Shut-Off. Used on double end shut-off models) 294PMD04 1 /4 1.787 0.500 294PMD06 3 /8 1.972 0.500 STYLE 298P oupler Single End Shut-Off 298P04X02 1 /4 1 /8 2.261 1.260 0.500 0.500 298P04X04 1 /4 1 /4 2.261 1.260 0.500 0.562 298P06X04 3 /8 1 /4 2.323 1.400 0.500 0.625 D STYLE 298PD oupler Double End Shut-Off 298PD04X02 1 /4 1 /8 2.802 1.260 0.500 0.500 298PD04X04 1 /4 1 /4 2.824 1.260 0.500 0.562 298PD06X04 3 /8 1 /4 2.962 1.400 0.500 0.625 D STYLE 298PT ody with Shut-Off (Standard on both double and single shut-off models) 298PT04X02 1 /4 1 /8 1.260 0.500 298PT04X04 1 /4 1 /4 1.260 0.562 298PT06X04 3 /8 1 /4 1.400 0.625 34
Poly-Flo Kwik-onnect ouplers Tube Fittings Material: Stainless Steel Wrench Wrench Part Tube Pipe ulkhead Pad/Hex Pad/Hex Style No. O.D. Thread Thread D STYLE 294PSS ody Single End Shut-Off 294PSS04 1 /4 1 /2-24 1.790 0.625 294PSS06 3 /8 11 /16-24 1.965 0.812 STYLE 294PMSS Insert Single End Shut-Off 294PMSS04 1 /4 1.636 0.500 294PMSS06 3 /8 1.738 0.500 STYLE 294PMSSD Insert Double End Shut-Off ` 294PMSSD04 1 /4 1.787 0.500 294PMSSD06 3 /8 1.972 0.500 STYLE 294PSS oupler Single End Shut-Off 294PSS04 1 /4 1 /2-24 2.899 1.718 0.625 294PSS06 3 /8 11 /16-24 3.461 1.921 0.812 35
Tube Fittings Poly-Flo Kwik-onnect ouplers Material: Stainless Steel Wrench Wrench Part Tube Pipe ulkhead Pad/Hex Pad/Hex Style No. O.D. Thread Thread D STYLE 294PSSD oupler Double End Shut-Off 294PSSD04 1 /4 1 /2-24 3.180 1.790 0.625 294PSSD06 3 /8 11 /16-24 3.458 1.965 0.812 STYLE 298PSS oupler Single End Shut-Off 298PSS04X02 1 /4 1 /8 2.261 1.260 0.500 0.500 298PSS04X04 1 /4 1 /4 2.261 1.260 0.500 0.562 298PSS06X04 3 /8 1 /4 2.323 1.400 0.500 0.625 D STYLE 298PSSD oupler Double End Shut-Off 298PSSD04X02 1 /4 1 /8 2.802 1.260 0.500 0.500 298PSSD04X04 1 /4 1 /4 2.824 1.260 0.500 0.562 298PSSD06X04 3 /8 1 /4 2.962 1.400 0.500 0.625 D STYLE 298PTSS ody with Shut-Off (Standard on both double and single shut-off models) 298PTSS04X02 1 /4 1 /8 1.260 0.500 298PTSS04X04 1 /4 1 /4 1.260 0.562 298PTSS06X04 3 /8 1 /4 1.400 0.625 36
Tube Fittings Omega-Flo Push-to-onnect/Push-to-Release Pneumatic Material: rass Min. Tube Wrench Part Tube Pipe Orifice Insert Pad/Hex Style No. O.D. Thread Size STYLE 262OF Union ody 262OF02 1 /8 0.078 1.652 0.375 262OF5/32 5 /32 0.109 1.652 0.437 262OF04 1 /4 0.188 2.008 0.500 262OF05 5 /16 0.236 2.059 0.625 262OF06 3 /8 0.250 2.259 0.688 262OF08 1 /2 0.375 2.406 0.812 STYLE 264OF Union Tee 264OF02 1 /8 0.078 0.835 0.437 264OF5/32 5 /32 0.109 0.851 0.500 264OF04 1 /4 0.188 1.009 0.562 264OF05 5 /16 0.236 1.062 0.750 264OF06 3 /8 0.250 1.087 0.750 264OF08 1 /2 0.375 1.325 1.000 STYLE 265OF Union Elbow 265OF02 1 /8 0.078 0.823 0.823 0.437 265OF5/32 5 /32 0.109 0.842 0.842 0.500 265OF04 1 /4 0.188 1.012 1.012 0.562 265OF05 5 /16 0.236 1.107 1.107 0.687 265OF06 3 /8 0.250 1.132 1.132 0.750 265OF08 1 /2 0.375 1.284 1.284 0.875 STYLE 266OF Female onnector 266OF02X02 1 /8 1 /8 0.078 1.200 0.562 266OF5/32X02 5 /32 1 /8 0.109 1.200 0.562 266OF03X02 3 /16 1 /8 0.125 1.199 0.562 266OF04X02 1 /4 1 /8 0.188 1.279 0.562 266OF04X04 1 /4 1 /4 0.188 1.467 0.688 266OF05X02 5 /16 1 /8 0.236 1.417 0.687 266OF05X04 5 /16 1 /4 0.236 1.639 0.750 266OF06X04 3 /8 1 /4 0.250 1.611 0.750 266OF06X06 3 /8 3 /8 0.250 1.651 0.875 37
Tube Fittings Omega-Flo Push-to-onnect/Push-to-Release Pneumatic Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 268OF Male onnector 268OF02X01 1 /8 1 /16 0.078 1.038 0.375 268OF02X02 1 /8 1 /8 0.078 1.038 0.437 268OF02X04 1 /8 1 /4 0.078 1.225 0.562 268OF5/32X02 5 /32 1 /8 0.109 1.038 0.437 268OF5/32X04 5 /32 1 /4 0.109 1.225 0.562 268OF03X02 3 /16 1 /8 0.125 1.035 0.437 268OF03X04 3 /16 1 /4 0.125 1.222 0.562 268OF04X01 1 /4 1 /16 0.188 1.184 0.500 268OF04X02 1 /4 1 /8 0.188 1.184 0.500 268OF04X04 1 /4 1 /4 0.188 1.371 0.562 268OF04X06 1 /4 3 /8 0.188 1.371 0.688 268OF05X02 5 /16 1 /8 0.236 1.206 0.688 268OF05X04 5 /16 1 /4 0.236 1.423 0.688 268OF06X02 3 /8 1 /8 0.250 1.290 0.750 268OF06X04 3 /8 1 /4 0.250 1.423 0.750 268OF06X06 3 /8 3 /8 0.250 1.423 0.750 268OF06X08 3 /8 1 /2 0.250 1.611 0.875 268OF08X06 1 /2 3 /8 0.375 1.472 0.875 268OF08X08 1 /2 1 /2 0.375 1.670 0.875 268OF08X08 1 /2 1 /2 0.375 1.670 0.875 STYLE 269OF Male Elbow 269OF02X02 1 /8 1 /8 0.078 0.823 0.717 0.437 269OF5/32X02 5 /32 1 /8 0.109 0.842 0.742 0.500 269OF5/32X04 5 /32 1 /4 0.109 0.842 0.923 0.500 269OF03X02 3 /16 1 /8 0.125 0.823 0.789 0.562 269OF03X04 3 /16 1 /4 0.125 0.823 0.976 0.562 269OF04X02 1 /4 1 /8 0.188 0.929 0.789 0.562 269OF04X04 1 /4 1 /4 0.188 0.939 0.976 0.562 269OF05X02 5 /16 1 /8 0.188 1.107 0.868 0.687 269OF05X04 5 /16 1 /4 0.236 1.107 1.055 0.687 269OF06X04 3 /8 1 /4 0.250 1.132 1.086 0.750 269OF06X06 3 /8 3 /8 0.250 1.132 1.086 0.750 269OF06X08 3 /8 1 /2 0.250 1.132 1.277 0.750 269OF08X06 1 /2 3 /8 0.375 1.221 1.164 0.875 269OF08X08 1 /2 1 /2 0.375 1.221 1.352 0.875 Min. Wrench Wrench Part Tube Pipe Orifice Pad/Hex Pad/Hex Style No. O.D. Thread Size D STYLE 269OFS Male Elbow Swivel D 269OFS02X02 1 /8 1 /8 0.078 0.846 0.437 0.500 1.057 269OFS5/32X02 5 /32 1 /8 0.109 0.862 0.437 0.500 1.061 269OFS5/32X04 5 /32 1 /4 0.109 0.862 0.562 0.500 1.184 269OFS03X02 3 /16 1 /8 0.125 0.843 0.437 0.562 1.057 269OFS03X04 3 /16 1 /4 0.125 0.893 0.562 0.562 1.186 269OFS04X02 1 /4 1 /8 0.125 0.959 0.437 0.562 1.051 269OFS04X04 1 /4 1 /4 0.188 1.009 0.562 0.562 1.186 269OFS04X06 1 /4 3 /8 0.188 1.009 0.688 0.562 1.186 269OFS05X02 5 /16 1 /8 0.125 1.107 0.437 0.687 1.099 269OFS05X04 5 /16 1 /4 0.188 1.107 0.562 0.687 1.290 269OFS06X02 3 /8 1 /8 0.125 1.092 0.437 0.750 1.138 269OFS06X04 3 /8 1 /4 0.188 1.092 0.562 0.750 1.335 269OFS06X06 3 /8 3 /8 0.250 1.092 0.688 0.750 1.397 269OFS06X08 3 /8 1 /2 0.250 1.119 0.875 0.750 1.570 269OFS08X06 1 /2 3 /8 0.250 1.253 0.688 0.875 1.506 269OFS08X08 1 /2 1 /2 0.250 1.208 0.875 0.875 1.636 38
Tube Fittings Omega-Flo Push-to-onnect/Push-to-Release Pneumatic Material: rass Min. Wrench Wrench Part Tube Pipe Orifice Pad/Hex Pad/Hex Style No. O.D. Thread Size D STYLE 271OFS Male Run Tee Swivel D 271OFS02X02 1 /8 1 /8 0.078 0.838 0.437 0.437 0.941 271OFS5/32X02 5 /32 1 /8 0.109 0.863 0.437 0.500 1.055 271OFS04X02 1 /4 1 /8 0.125 1.012 0.437 0.562 1.083 271OFS04X04 1 /4 1 /4 0.188 0.991 0.562 0.562 1.180 271OFS05X02 5 /16 1 /8 0.125 1.087 0.437 0.750 1.128 271OFS05X04 5 /16 1 /4 0.188 1.087 0.562 0.750 1.330 271OFS06X04 3 /8 1 /4 0.188 1.123 0.562 0.750 1.330 271OFS06X06 3 /8 3 /8 0.250 1.123 0.688 0.750 1.330 271OFS08X06 1 /2 3 /8 0.250 1.325 0.688 1.000 1.559 271OFS08X08 1 /2 1 /2 0.375 1.325 0.875 1.000 1.808 STYLE 272OFS Male ranch Tee Swivel D 272OFS02X02 1 /8 1 /8 0.078 0.838 0.437 0.437 0.941 272OFS5/32X02 5 /32 1 /8 0.109 0.863 0.437 0.500 1.055 272OFS04X02 1 /4 1 /8 0.125 1.012 0.437 0.562 1.083 272OFS04X04 1 /4 1 /4 0.188 0.991 0.562 0.562 1.180 272OFS05X02 5 /16 1 /8 0.125 1.087 0.437 0.750 1.128 272OFS05X04 5 /16 1 /4 0.188 1.087 0.562 0.750 1.330 272OFS06X04 3 /8 1 /4 0.188 1.123 0.562 0.750 1.330 272OFS06X06 3 /8 3 /8 0.250 1.123 0.688 0.750 1.330 272OFS08X06 1 /2 3 /8 0.250 1.325 0.688 1.000 1.559 272OFS08X08 1 /2 1 /2 0.375 1.325 0.875 1.000 1.808 Min. Wrench Wrench ulkhead Part Tube Pipe Orifice Pad/Hex Pad/Hex Thread Style No. O.D. Thread Size D STYLE 282OF ulkhead Union 282OF02 1 /8 0.078 1.652 0.245 0.688 9 /16-24 282OF5/32 5 /32 0.109 1.652 0.245 0.812 5 /8-18 282OF04 1 /4 0.188 2.008 0.245 0.812 11 /16-24 282OF05 5 /16 0.236 2.059 0.260 1.000 7 /8-18 282OF06 3 /8 0.250 2.259 0.260 1.125 15 /16-16 282OF08 1 /2 0.375 2.406 0.296 1.250 1 1 /8-16 D E Omega-Flo ccessories Material: Polyethylene Part Tube Style No. O.D. STYLE 209OF Plug 209OF02 1 /8 1.120 209OF5/32 5 /32 1.120 209OF04 1 /4 1.280 209OF05 5 /16 1.450 209OF06 3 /8 1.450 209OF08 1 /2 1.590 39
Tube Fittings Hi-Duty Flareless Material: rass Min. Wrench ulkhead Part Tube Pipe Orifice Pad/Hex Thread Style No. O.D. Thread Size D E STYLE 66L ulkhead Female onnector 66L04X04 1 /4 1 /4 0.187 1.437 1.031 0.875 0.625 3 /4-18 D E STYLE 72L ulkhead Union E D 72L02 1 /8 0.093 1.781 1.156 0.562 0.625 7 /16-24 72L04 1 /4 0.187 1.968 1.156 0.687 0.625 9 /16-24 72L06 3 /8 0.312 2.125 1.312 0.812 0.625 11 /16-24 STYLE 81L Nut 81L02 1 /8 0.656 0.312 81L03 3 /16 0.687 0.375 81L04 1 /4 0.734 0.437 81L05 5 /16 0.765 0.500 81L06 3 /8 0.843 0.562 81L08 1 /2 0.921 0.688 81L10 5 /8 1.078 0.875 81L12 3 /4 1.140 1.000 81L16 1 1.218 1.250 STYLE 82L Union 82L02 1 /8 0.093 1.687 1.062 0.375 82L03 3 /16 0.125 1.781 1.031 0.437 82L04 1 /4 0.187 1.906 1.093 0.562 82L05 5 /16 0.250 2.000 1.187 0.562 82L06 3 /8 0.312 2.187 1.375 0.625 82L08 1 /2 0.437 2.437 1.562 0.812 82L10 5 /8 0.500 2.937 1.812 1.062 40
Hi-Duty Flareless Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 84L Union Tee 84L02 1 /8 0.093 1.031 0.718 0.312 84L03 3 /16 0.125 1.093 0.718 0.312 84L04 1 /4 0.187 1.093 0.687 0.437 84L06 3 /8 0.312 1.343 0.937 0.562 84L08 1 /2 0.437 1.468 1.031 0.687 84L10 5 /8 0.500 1.843 1.281 1.000 STYLE 85L Union Elbow 85L04 1 /4 0.187 1.093 0.687 0.437 85L06 3 /8 0.312 1.343 0.937 0.562 85L08 1 /2 0.437 1.562 1.125 0.687 85L10 5 /8 0.500 1.968 1.406 1.000 STYLE 86L Female onnector 86L02X02 1 /8 1 /8 0.093 1.312 1.000 0.500 86L03X02 3 /16 1 /8 0.125 1.375 1.000 0.500 86L04X02 1 /4 1 /8 0.187 1.406 1.000 0.562 86L04X04 1 /4 1 /4 0.187 1.593 1.187 0.687 86L06X02 3 /8 1 /8 0.312 1.531 1.125 0.625 86L06X04 3 /8 1 /4 0.312 1.718 1.312 0.625 86L06X06 3 /8 3 /8 0.312 1.750 1.343 0.812 86L06X08 3 /8 1 /2 0.312 1.968 1.562 1.000 86L08X06 1 /2 3 /8 0.437 2.250 1.812 0.812 86L08X08 1 /2 1 /2 0.437 2.062 1.625 1.000 41
Tube Fittings Hi-Duty Flareless Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 87L Reducing Union 87L04X03 1 /4 x 3 /16 0.125 1.812 1.031 0.562 87L06X04 3 /8 x 1 /4 0.187 2.000 1.187 0.625 87L08X04 1 /2 x 1 /4 0.187 2.125 1.281 0.812 87L08X06 1 /2 x 3 /8 0.312 2.656 1.406 0.812 STYLE 88L Male onnector 88L02X02 1 /8 1 /8 0.093 1.062 0.750 0.406 88L03X02 3 /16 1 /8 0.125 1.140 0.765 0.437 88L04X02 1 /4 1 /8 0.187 1.343 0.937 0.562 88L04X04 1 /4 1 /4 0.187 1.468 1.062 0.562 88L04X06 1 /4 3 /8 0.187 1.343 0.937 0.687 88L04X08 1 /4 1 /2 0.187 1.531 1.125 0.875 88L05X02 5 /16 1 /8 0.218 1.406 1.000 0.562 88L05X04 5 /16 1 /4 0.218 1.500 1.093 0.562 88L06X02 3 /8 1 /8 0.218 1.531 1.125 0.625 88L06X04 3 /8 1 /4 0.312 1.656 1.250 0.625 88L06X06 3 /8 3 /8 0.312 1.531 1.125 0.687 88L06X08 3 /8 1 /2 0.312 1.531 1.125 0.875 88L08X04 1 /2 1 /4 0.312 1.813 1.375 0.812 88L08X06 1 /2 3 /8 0.406 1.750 1.312 0.812 88L08X08 1 /2 1 /2 0.437 1.812 1.375 0.875 88L08X12 1 /2 3 /4 0.437 1.625 1.187 1.062 88L10X06 5 /8 3 /8 0.406 2.031 1.468 1.062 88L10X08 5 /8 1 /2 0.500 2.156 1.593 1.062 88L10X12 5 /8 3 /4 0.500 1.812 1.250 1.062 88L12X08 3 /4 1 /2 0.562 2.343 1.750 1.250 88L12X12 3 /4 3 /4 0.625 2.218 1.625 1.250 88L16X16 1 1 0.875 2.843 2.187 1.500 42
Hi-Duty Flareless Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size D STYLE 89L Male Elbow D 89L02X02 1 /8 1 /8 0.093 0.968 0.656 0.375 0.687 89L03X02 3 /16 1 /8 0.125 1.062 0.687 0.437 0.750 89L04X02 1 /4 1 /8 0.187 1.093 0.687 0.437 0.750 89L04X04 1 /4 1 /4 0.187 1.156 0.750 0.500 0.937 89L04X06 1 /4 3 /8 0.187 1.187 0.781 0.562 1.000 89L05X02 5 /16 1 /8 0.218 1.093 0.687 0.500 0.781 89L05X04 5 /16 1 /4 0.250 1.218 0.812 0.500 1.062 89L06X02 3 /8 1 /8 0.218 1.250 0.843 0.562 0.875 89L06X04 3 /8 1 /4 0.312 1.250 0.843 0.562 1.000 89L06X06 3 /8 3 /8 0.312 1.343 0.937 0.562 1.031 89L06X08 3 /8 1 /2 0.312 1.375 0.968 0.687 1.250 89L08X04 1 /2 1 /4 0.312 1.437 1.000 0.687 1.062 89L08X06 1 /2 3 /8 0.406 1.437 1.000 0.687 1.062 89L08X08 1 /2 1 /2 0.437 1.468 1.031 0.687 1.312 89L10X06 5 /8 3 /8 0.406 1.750 1.187 0.875 1.343 89L10X08 5 /8 1 /2 0.500 1.750 1.187 0.875 1.375 89L12X12 3 /4 3 /4 0.625 1.937 1.343 1.000 1.468 STYLE 90L Female Elbow 90L02X02 1 /8 1 /8 0.093 1.031 0.718 0.375 0.718 90L04X02 1 /4 1 /8 0.187 1.093 0.687 0.437 0.750 90L04X04 1 /4 1 /4 0.187 1.250 0.843 0.500 0.875 90L06X02 3 /8 1 /8 0.312 1.250 0.843 0.562 0.937 90L06X04 3 /8 1 /4 0.312 1.343 0.937 0.562 1.093 90L06X06 3 /8 3 /8 0.312 1.468 1.062 0.625 0.937 90L08X06 1 /2 3 /8 0.437 1.500 1.062 0.687 1.281 90L08X08 1 /2 1 /2 0.437 1.656 1.218 0.875 1.188 D 43
Tube Fittings Hi-Duty Flareless Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size D STYLE 91L Male Run Tee 91L03X02 3 /16 1 /8 0.125 1.093 0.718 0.312 0.718 91L04X02 1 /4 1 /8 0.187 1.156 0.750 0.375 0.750 91L04X04 1 /4 1 /4 0.187 1.218 0.812 0.437 0.937 91L06X04 3 /8 1 /4 0.312 1.343 0.937 0.562 1.000 91L06X06 3 /8 3 /8 0.312 1.406 1.000 0.625 1.125 D STYLE 92L Male ranch Tee 92L02X02 1 /8 1 /8 0.093 1.031 0.718 0.312 0.718 92L03X02 3 /16 1 /8 0.125 1.093 0.718 0.312 0.718 92L04X02 1 /4 1 /8 0.187 1.093 0.687 0.437 0.750 92L04X04 1 /4 1 /4 0.187 1.281 0.875 0.437 0.937 92L06X04 3 /8 1 /4 0.312 1.343 0.937 0.562 1.000 92L06X06 3 /8 3 /8 0.312 1.406 1.000 0.625 1.125 92L08X06 1 /2 3 /8 0.406 1.468 1.031 0.687 1.031 D STYLE 94L 45 Male Elbow 94L02X02 1 /8 1 /8 0.093 1.000 0.687 0.437 0.687 94L03X02 3 /16 1 /8 0.125 1.062 0.687 0.437 0.687 94L04X02 1 /4 1 /8 0.187 1.093 0.687 0.437 0.687 94L04X04 1 /4 1 /4 0.187 1.093 0.687 0.562 0.843 94L06X04 3 /8 1 /4 0.312 1.187 0.781 0.562 0.843 94L06X06 3 /8 3 /8 0.312 1.281 0.875 0.500 0.875 94L08X06 1 /2 3 /8 0.406 1.375 0.937 0.812 1.062 D 44
Hi-Duty Flareless Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size D STYLE 95L Female ranch Tee 95L04X02 1 /4 1 /8 0.187 1.093 0.687 0.437 0.750 95L04X04 1 /4 1 /4 0.187 1.156 0.750 0.562 1.093 95L06X04 3 /8 1 /4 0.312 1.343 0.937 0.562 1.093 95L06X06 3 /8 3 /8 0.312 1.406 1.000 0.625 1.187 95L08X06 1 /2 3 /8 0.437 1.468 1.031 0.687 1.031 95L10X08 5 /8 1 /2 0.500 1.843 1.281 1.000 1.250 95L12X08 3 /4 1 /2 0.625 1.906 1.312 1.093 1.437 D STYLE 99L Plug 99L02 1 /8 0.656 0.375 99L04 1 /4 0.734 0.437 99L06 3 /8 0.843 0.625 99L08 1 /2 0.921 0.750 45
Tube Fittings Flex Flareless Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 60FL Nitrile Sleeve 250 F max 60FL02 1 /8 0.203 60FL03 3 /16 0.197 60FL04 1 /4 0.213 60FL05 5 /16 0.244 60FL06 3 /8 0.250 60FL08 1 /2 0.356 60FL10 5 /8 0.479 60FL12 3 /4 0.594 60FL16 1 STYLE 60FLV Viton Sleeve 450 max 60FLV03 3 /16 0.197 60FLV04 1 /4 0.213 60FLV05 5 /16 0.244 60FLV06 3 /8 0.250 60FLV08 1 /2 0.356 60FLV10 5 /8 0.479 60FLV12 3 /4 0.594 STYLE 61FL Nut 61FL02 1 /8 0.437 0.437 61FL03 3 /16 0.468 0.500 61FL04 1 /4 0.500 0.562 61FL05 5 /16 0.531 0.625 61FL06 3 /8 0.531 0.750 61FL08 1 /2 0.671 0.937 61FL10 5 /8 0.875 1.125 61FL12 3 /4 0.984 1.250 61FL16 1 STYLE 62FL Union 62FL02 1 /8 0.093 1.078 0.703 0.437 62FL03 3 /16 0.125 1.140 0.703 0.500 62FL04 1 /4 0.187 1.203 0.765 0.562 62FL05 5 /16 0.250 1.296 0.796 0.625 62FL06 3 /8 0.312 1.296 0.796 0.687 46
Flex Flareless Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 63FL Male onnector heck 63FL04X02 1 /4 1 /8 0.136 1.234 0.843 0.562 STYLE 64FL Union Tee 64FL04 1 /4 0.187 0.968 0.750 0.437 64FL06 3 /8 0.312 1.250 1.000 0.625 STYLE 66FL Female onnector 66FL02X02 1 /8 1 /8 0.093 0.937 0.750 0.500 66FL04X02 1 /4 1 /8 0.187 1.000 0.781 0.562 66FL05X02 5 /16 1 /8 0.250 1.031 0.781 0.625 66FL06X04 3 /8 1 /4 0.312 1.218 0.968 0.687 66FL08X06 1 /2 3 /8 0.437 1.421 1.093 0.875 STYLE 68FL Male onnector 68FL02X02 1 /8 1 /8 0.093 1.000 0.812 0.437 68FL03X02 3 /16 1 /8 0.125 1.031 0.812 0.500 68FL04X02 1 /4 1 /8 0.187 1.062 0.843 0.562 68FL04X04 1 /4 1 /4 0.187 1.250 1.031 0.562 68FL05X02 5 /16 1 /8 0.218 1.125 0.875 0.625 68FL05X04 5 /16 1 /4 0.250 1.312 1.062 0.625 68FL06X02 3 /8 1 /8 0.218 1.125 0.875 0.687 68FL06X04 3 /8 1 /4 0.312 1.312 1.062 0.687 68FL06X06 3 /8 3 /8 0.312 1.312 1.062 0.687 68FL08X06 1 /2 3 /8 0.406 1.484 1.156 0.875 68FL08X08 1 /2 1 /2 0.406 1.671 1.343 0.875 68FL10X08 5 /8 1 /2 0.562 1.906 1.437 1.062 STYLE 68FLV Male onnector with Viton Sleeve 68FLV03X02 3 /16 1 /8 0.125 1.031 0.812 0.500 68FLV04X02 1 /4 1 /8 0.187 1.062 0.843 0.562 68FLV06X06 3 /8 3 /8 0.312 1.312 1.062 0.687 68FLV08X06 1 /2 3 /8 0.406 1.484 1.156 0.875 47
Tube Fittings Flex Flareless Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size D STYLE 69FL Male Elbow D 69FL02X02 1 /8 1 /8 0.120 0.906 0.718 0.375 0.718 69FL03X02 3 /16 1 /8 0.156 0.906 0.687 0.437 0.750 69FL04X02 1 /4 1 /8 0.187 0.844 0.625 0.500 0.781 69FL04X04 1 /4 1 /4 0.187 1.062 0.843 0.562 1.000 69FL05X02 5 /16 1 /8 0.218 0.937 0.687 0.437 0.843 69FL05X04 5 /16 1 /4 0.250 1.062 0.812 0.562 1.000 69FL06X02 3 /8 1 /8 0.218 1.093 0.843 0.625 0.906 69FL06X04 3 /8 1 /4 0.312 1.093 0.843 0.625 1.062 69FL06X06 3 /8 3 /8 0.312 1.187 0.937 0.625 1.125 69FL08X06 1 /2 3 /8 0.406 1.328 1.000 0.687 1.062 69FL08X08 1 /2 1 /2 0.437 1.390 1.062 0.750 1.437 69FL10X08 5 /8 1 /2 0.562 1.750 1.281 1.000 1.468 STYLE 69FLV Male Elbow with Viton Sleeve 69FLV04X04 1 /4 1 /4.187 1.062 0.843 0.562 1.000 69FLV06X04 3 /8 1 /4.312 1.093 0.843 0.625 1.062 69FLV06X06 3 /8 3 /8.312 1.187 0.937 0.625 1.125 D STYLE 71FL Male Run Tee 71FL04X02 1 /4 1 /8.187 0.968 0.750 0.500 0.781 71FL04X04 1 /4 1 /4.187 1.062 0.843 0.437 0.937 D STYLE 72FL Male ranch Tee 72FL04X02 1 /4 1 /8 0.187 0.968 0.750 0.500 0.781 72FL06X04 3 /8 1 /4 0.312 1.156 0.906 0.562 1.000 D 48
ompression Flareless Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 60F Sleeve 60F02 1 /8 0.188 60F156 5 /32 0.188 60F03 3 /16 0.219 60F04 1 /4 0.250 60F05 5 /16 0.250 60F06 3 /8 0.250 60F07 7 /16 0.312 60F08 1 /2 0.375 60F10 5 /8 0.438 60F12 3 /4 0.500 STYLE 61F Nut 61F02 1 /8 0.375 0.375 61F156 5 /32 0.344 0.375 61F03 3 /16 0.406 0.437 61F04 1 /4 0.438 0.500 61F05 5 /16 0.438 0.562 61F06 3 /8 0.469 0.625 61F07 7 /16 0.500 0.688 61F08 1 /2 0.625 0.812 61F10 5 /8 0.770 0.938 61F12 3 /4 0.810 1.125 STYLE 62F Union 62F02 1 /8 0.093 1.125 0.656 0.312 62F156 5 /32 0.109 1.125 0.656 0.312 62F03 3 /16 0.125 1.250 0.750 0.375 62F04 1 /4 0.188 1.438 0.812 0.437 62F05 5 /16 0.250 1.469 0.875 0.500 62F06 3 /8 0.312 1.578 0.984 0.562 62F08 1 /2 0.406 1.938 1.093 0.688 62F10 5 /8 0.531 2.359 1.450 0.812 62F12 3 /4 0.656 2.562 1.620 1.000 49
Tube Fittings ompression Flareless Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 63F all heck 63F02X02 1 /8 1 /8 0.093 1.015 0.781 0.437 63F03X02 3 /16 1 /8 0.136 1.093 0.844 0.437 63F04X02 1 /4 1 /8 0.136 1.188 0.875 0.437 STYLE 64F Union Tee 64F02 1 /8 0.093 0.859 0.625 0.312 64F03 3 /16 0.125 0.875 0.625 0.312 64F04 1 /4 0.188 0.938 0.671 0.437 64F05 5 /16 0.250 0.974 0.688 0.437 64F06 3 /8 0.312 1.078 0.781 0.500 64F08 1 /2 0.406 1.359 0.938 0.625 64F10 5 /8 0.531 1.594 1.130 0.812 STYLE 65F Union Elbow 65F02 1 /8 0.093 0.859 0.625 0.312 65F03 3 /16 0.125 0.875 0.625 0.375 65F04 1 /4 0.188 0.938 0.625 0.375 65F05 5 /16 0.250 0.984 0.688 0.437 65F06 3 /8 0.312 1.078 0.781 0.500 65F08 1 /2 0.406 1.359 0.938 0.625 65F10 5 /8 0.531 1.547 1.093 0.812 STYLE 66F Female onnector 66F02X02 1 /8 1 /8 0.093 0.984 0.750 0.562 66F03X02 3 /16 1 /8 0.125 1.031 0.781 0.562 66F04X02 1 /4 1 /8 0.188 1.093 0.781 0.562 66F04X04 1 /4 1 /4 0.188 1.344 1.031 0.688 66F05X02 5 /16 1 /8 0.250 1.109 0.812 0.562 66F05X04 5 /16 1 /4 0.250 1.328 1.031 0.688 66F06X02 3 /8 1 /8 0.250 1.141 0.844 0.562 66F06X04 3 /8 1 /4 0.312 1.359 1.062 0.688 66F08X06 1 /2 3 /8 0.406 1.547 1.125 0.875 66F08X08 1 /2 1 /2 0.406 1.766 1.344 1.000 66F10X08 5 /8 1 /2 0.531 1.969 1.510 1.062 50
ompression Flareless Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size D STYLE 68F Male onnector 68F02X02 1 /8 1 /8 0.093 1.031 0.797 0.437 68F02X04 1 /8 1 /4 0.093 1.234 1.000 0.562 68F02X06 1 /8 3 /8 0.093 1.329 1.031 0.750 68F03X02 3 /16 1 /8 0.125 1.109 0.859 0.437 68F03X04 3 /16 1 /4 0.125 1.329 1.031 0.562 68F04X02 1 /4 1 /8 0.188 1.187 0.875 0.437 68F04X04 1 /4 1 /4 0.188 1.375 1.062 0.562 68F04X06 1 /4 3 /8 0.188 1.375 1.062 0.688 68F04X08 1 /4 1 /2 0.188 1.594 1.281 0.875 68F05X02 5 /16 1 /8 0.250 1.203 0.906 0.500 68F05X04 5 /16 1 /4 0.250 1.391 1.093 0.562 68F06X02 3 /8 1 /8 0.250 1.266 0.969 0.562 68F06X04 3 /8 1 /4 0.312 1.453 1.156 0.562 68F06X06 3 /8 3 /8 0.312 1.453 1.156 0.688 68F06X08 3 /8 1 /2 0.312 1.672 1.375 0.875 68F06X12 3 /8 3 /4 0.312 1.672 1.375 1.062 68F08X02 1 /2 1 /8 0.188 1.469 1.156 0.688 68F08X04 1 /2 1 /4 0.312 1.562 1.250 0.688 68F08X06 1 /2 3 /8 0.406 1.641 1.219 0.688 68F08X08 1 /2 1 /2 0.406 1.859 1.438 0.875 68F08X12 1 /2 3 /4 0.406 1.922 1.500 1.125 68F08X16 1 /2 1 0.406 2.000 1.688 1.375 68F10X08 5 /8 1 /2 0.531 2.062 1.610 0.875 68F10X12 5 /8 3 /4 0.531 2.000 1.640 1.125 68F12X08 3 /4 1 /2 0.531 2.188 1.710 1.000 68F12X12 3 /4 3 /4 0.656 2.188 1.710 1.062 STYLE 69F Male Elbow D 69F02X02 1 /8 1 /8 0.093 0.859 0.625 0.312 0.688 69F02X04 1 /8 1 /4 0.094 0.828 0.594 0.438 0.938 69F03X02 3 /16 1 /8 0.125 0.875 0.625 0.437 0.688 69F03X04 3 /16 1 /4 0.125 0.895 0.641 0.437 0.922 69F04X02 1 /4 1 /8 0.188 0.969 0.656 0.375 0.750 69F04X04 1 /4 1 /4 0.188 1.031 0.719 0.438 0.938 69F04X06 1 /4 3 /8 0.188 1.062 0.750 0.562 1.000 69F04X08 1 /4 1 /2 0.188 1.188 0.875 0.688 1.250 69F05X02 5 /16 1 /8 0.234 0.922 0.625 0.438 0.750 69F05X04 5 /16 1 /4 0.250 1.046 0.750 0.438 0.938 69F06X02 3 /8 1 /8 0.219 1.046 0.750 0.500 0.844 69F06X04 3 /8 1 /4 0.312 1.078 0.781 0.500 0.938 69F06X06 3 /8 3 /8 0.312 1.172 0.875 0.562 1.000 69F06X08 3 /8 1 /2 0.312 1.234 0.938 0.688 1.250 69F06X12 3 /8 3 /4 0.312 1.375 1.062 1.062 1.250 69F08X02 1 /2 1 /8 0.188 1.219 0.844 0.688 1.000 69F08X04 1 /2 1 /4 0.344 1.359 0.938 0.625 1.062 69F08X06 1 /2 3 /8 0.406 1.359 0.938 0.625 1.125 69F08X08 1 /2 1 /2 0.406 1.422 1.000 0.688 1.250 69F08X12 1 /2 3 /4 0.406 1.437 1.125 0.750 1.281 69F10X08 5 /8 1 /2 0.531 1.594 1.130.0812 1.280 69F10X12 5 /8 3 /4 0.531 1.719 1.260 0.938 1.500 69F12X08 3 /4 1 /2 0.656 1.672 1.200 0.875 1.340 51
Tube Fittings ompression Flareless Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size D STYLE 70F Female Elbow D 70F02X02 1 /8 1 /8 0.093 0.922 0.688 0.562 0.547 70F03X02 3 /16 1 /8 0.125 0.969 0.719 0.562 0.547 70F04X02 1 /4 1 /8 0.188 1.062 0.750 0.562 0.547 70F04X04 1 /4 1 /4 0.188 1.188 0.875 0.688 0.719 70F05X02 5 /16 1 /8 0.250 0.984 0.688 0.438 0.688 70F06X04 3 /8 1 /4 0.312 1.141 0.844 0.500 0.875 70F08X06 1 /2 3 /8 0.406 1.453 1.031 0.625 0.906 70F08X08 1 /2 1 /2 0.406 1.547 1.125 0.688 1.188 STYLE 71F Male Run Tee 71F04X02 1 /4 1 /8 0.188 1.000 0.688 0.375 0.750 71F05X02 5 /16 1 /8 0.219 0.953 0.656 0.438 0.750 71F06X04 3 /8 1 /4 0.312 1.078 0.781 0.500 0.938 71F08X06 1 /2 3 /8 0.406 1.359 0.938 0.625 1.093 D STYLE 72F Male ranch Tee 72F02X02 1 /8 1 /8 0.093 0.859 0.625 0.312 0.688 72F03X02 3 /16 1 /8 0.125 0.875 0.625 0.312 0.688 72F04X02 1 /4 1 /8 0.188 1.000 0.688 0.375 0.750 72F04X04 1 /4 1 /4 0.188 1.031 0.719 0.500 0.938 72F05X02 5 /16 1 /8 0.234 0.953 0.656 0.438 0.750 72F06X04 3 /8 1 /4 0.312 1.078 0.781 0.500 0.938 72F08X06 1 /2 3 /8 0.406 1.359 0.938 0.625 1.093 72F08X08 1 /2 1 /2 0.406 1.422 1.000 0.812 1.344 D 52
ompression Flareless Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size D STYLE 76F Tee D 76F02X02 1 /8 1 /8 0.093 0.953 0.719 0.562 0.531 76F03X02 3 /16 1 /8 0.125 1.031 0.781 0.562 0.531 76F04X02 1 /4 1 /8 0.188 1.093 0.781 0.562 0.531 76F06X04 3 /8 1 /4 0.312 1.234 0.938 0.750 0.750 STYLE 80F Straight Through Tank Fitting 80F04X04 1 /4 1 /4 0.257 1.375 1.062 0.562 80F06X06 3 /8 3 /8 0.382 1.453 1.156 0.688 80F08X08 1 /2 1 /2 0.516 1.859 1.438 0.875 STYLE 161F Long Nut 161F04 1 /4 0.750 0.500 161F06 3 /8 1.125 0.625 161F08 1 /2 1.060 0.812 53
Tube Fittings ompresamatic Flareless Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 61M Nut and Sleeve ssembly 61M02 1 /8 0.416 5/16-24 0.375 61M03 3 /16 0.432 3/8-24 0.437 61M04 1 /4 0.444 7/16-24 0.500 61M05 5 /16 0.475 1/2-24 0.562 61M06 3 /8 0.510 9/16-24 0.625 61M07 7 /16 0.525 5/8-24 0.688 61M08 1 /2 0.557 11/16-20 0.812 61M10 5 /8 0.584 13/16-18 0.938 61M12 3 /4 0.682 1-18 1.125 STYLE 62M Union 62M02 1 /8 0.093 1.281 0.656 0.312 62M03 3 /16 0.125 1.375 0.750 0.375 62M04 1 /4 0.188 1.437 0.812 0.437 62M05 5 /16 0.250 1.500 0.875 0.500 62M06 3 /8 0.312 1.609 0.984 0.562 62M08 1 /2 0.406 1.719 1.093 0.688 62M10 5 /8 0.531 2.172 1.450 0.812 62M12 3 /4 0.656 2.453 1.620 1.000 STYLE 63M Male onnector all heck 63M02X02 1 /8 1 /8 0.093 1.093 0.781 0.437 63M03X02 3 /16 1 /8 0.136 1.156 0.844 0.437 63M04X02 1 /4 1 /8 0.136 1.187 0.875 0.437 63M05X02 5 /16 1 /8 0.136 1.218 0.906 0.500 63M06X04 3 /8 1 /4 0.188 1.469 1.156 0.562 63M08X06 1 /2 3 /8 0.250 1.531 1.219 0.688 54
ompresamatic Flareless Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 64M Union Tee 64M02 1 /8 0.093 0.937 0.625 0.312 64M03 3 /16 0.125 0.937 0.625 0.312 64M04 1 /4 0.188 0.969 0.671 0.437 64M05 5 /16 0.250 1.000 0.688 0.437 64M06 3 /8 0.312 1.094 0.781 0.500 64M08 1 /2 0.406 1.250 0.938 0.624 64M10 5 /8 0.531 1.453 1.130 0.812 64M12 3 /4 0.656 1.734 1.312 1.000 STYLE 65M Union Elbow 65M02 1 /8 0.093 0.937 0.625 0.312 65M03 3 /16 0.125 0.937 0.625 0.375 65M04 1 /4 0.188 0.937 0.625 0.375 65M05 5 /16 0.250 1.000 0.688 0.437 65M06 3 /8 0.312 1.094 0.781 0.500 65M08 1 /2 0.406 1.250 0.938 0.625 65M10 5 /8 0.531 1.453 1.093 0.812 65M12 3 /4 0.656 1.734 1.281 1.000 55
Tube Fittings ompresamatic Flareless Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 66M Female onnector 66M02X02 1 /8 1 /8 0.093 1.062 0.750 0.562 66M03X02 3 /16 1 /8 0.125 1.094 0.781 0.562 66M03X04 3 /16 1 /4 0.125 1.281 0.969 0.688 66M04X02 1 /4 1 /8 0.188 1.094 0.781 0.562 66M04X04 1 /4 1 /4 0.188 1.344 1.031 0.688 66M05X02 5 /16 1 /8 0.250 1.125 0.812 0.562 66M05X04 5 /16 1 /4 0.250 1.344 1.031 0.688 66M06X02 3 /8 1 /2 0.250 1.156 0.844 0.562 66M06X04 3 /8 1 /4 0.312 1.375 1.062 0.688 66M08X06 1 /2 3 /8 0.406 1.437 1.125 0.875 66M08X08 1 /2 1 /2 0.406 1.656 1.344 1.000 66M10X08 5 /8 1 /2 0.531 1.875 1.510 1.062 66M12X08 3 /4 1 /2 0.656 2.000 1.580 1.062 Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size D STYLE 68M Male onnector 68M02X02 1 /8 1 /8 0.093 1.109 0.797 0.437 68M02X04 1 /8 1 /4 0.093 1.312 1.000 0.562 68M02X06 1 /8 3 /8 0.093 1.344 1.031 0.750 68M03X02 3 /16 1 /8 0.125 1.172 0.859 0.437 68M03X04 3 /16 1 /4 0.125 1.344 1.031 0.562 68M04X02 1 /4 1 /8 0.188 1.188 0.875 0.437 68M04X04 1 /4 1 /4 0.188 1.375 1.062 0.562 68M04X06 1 /4 3 /8 0.188 1.375 1.062 0.688 68M04X08 1 /4 1 /2 0.188 1.594 1.281 0.875 68M05X02 5 /16 1 /8 0.250 1.218 0.906 0.500 68M05X04 5 /16 1 /4 0.250 1.406 1.093 0.562 68M06X02 3 /8 1 /8 0.250 1.281 0.969 0.562 68M06X04 3 /8 1 /4 0.312 1.468 1.156 0.562 68M06X06 3 /8 3 /8 0.312 1.468 1.156 0.688 68M06X08 3 /8 1 /2 0.312 1.688 1.375 0.875 68M06X12 3 /8 3 /4 0.312 1.688 1.375 1.062 68M07X04 7 /16 1 /4 0.312 1.500 1.188 0.625 68M08X02 1 /2 1 /8 0.188 1.469 1.156 0.688 68M08X04 1 /2 1 /4 0.312 1.562 1.250 0.688 68M08X06 1 /2 3 /8 0.406 1.531 1.219 0.688 68M08X08 1 /2 1 /2 0.406 1.750 1.438 0.875 68M08X12 1 /2 3 /4 0.406 1.812 1.500 1.125 68M08X16 1 /2 1 0.406 2.000 1.688 1.375 68M10X08 5 /8 1 /2 0.531 1.969 1.610 0.875 68M10X12 5 /8 3 /4 0.531 2.000 1.640 1.125 68M12X08 3 /4 1 /2 0.531 2.125 1.710 1.000 68M12X12 3 /4 3 /4 0.656 2.125 1.710 1.125 56
Tube Fittings ompresamatic Flareless Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size D STYLE 69M Male Elbow D 69M02X01 1 /8 1 /16 0.094 0.875 0.562 0.375 0.688 69M02X02 1 /8 1 /8 0.093 0.937 0.625 0.312 0.688 69M02X04 1 /8 1 /4 0.094 0.906 0.594 0.437 0.938 69M02X06 1 /8 3 /8 0.094 1.000 0.688 0.500 1.125 69M03X02 3 /16 1 /8 0.125 0.937 0.625 0.375 0.688 69M03X04 3 /16 1 /4 0.125 0.953 0.641 0.437 0.922 69M04X02 1 /4 1 /8 0.188 0.969 0.656 0.375 0.750 69M04X04 1 /4 1 /4 0.188 1.031 0.719 0.437 0.938 69M04X06 1 /4 3 /8 0.188 1.062 0.750 0.562 1.000 69M04X08 1 /4 1 /2 0.188 1.188 0.875 0.688 1.250 69M05X02 5 /16 1 /8 0.250 0.937 0.625 0.437 0.750 69M05X04 5 /16 1 /4 0.250 1.062 0.750 0.437 0.938 69M06X02 3 /8 1 /8 0.312 1.062 0.750 0.500 0.844 69M06X04 3 /8 1 /4 0.312 1.094 0.781 0.500 0.938 69M06X06 3 /8 3 /8 0.312 1.188 0.875 0.562 1.000 69M06X08 3 /8 1 /2 0.312 1.250 0.938 0.688 1.250 69M06X12 3 /8 3 /4 0.312 1.375 1.062 1.062 1.250 69M07X04 7 /16 1 /4 0.312 1.158 0.844 0.688 1.000 69M08X02 1 /2 1 /8 0.188 1.219 0.906 0.562 0.812 69M08X04 1 /2 1 /4 0.406 1.250 0.938 0.625 1.062 69M08X06 1 /2 3 /8 0.406 1.250 0.938 0.625 1.125 69M08X08 1 /2 1 /2 0.406 1.312 1.000 0.688 1.250 69M08X12 1 /2 3 /4 0.406 1.437 1.125 0.750 1.281 69M10X08 5 /8 1 /2 0.531 1.500 1.130 0.812 1.280 69M10X12 5 /8 3 /4 0.531 1.625 1.260 0.938 1.500 69M12X08 3 /4 1 /2 0.656 1.625 1.200 0.875 1.340 57
Tube Fittings ompresamatic Flareless Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size D STYLE 70M Female Elbow D 70M02X02 1 /8 1 /8 0.093 1.000 0.688 0.562 0.547 70M03X02 3 /16 1 /8 0.125 1.031 0.719 0.562 0.547 70M04X02 1 /4 1 /8 0.188 1.062 0.750 0.562 0.547 70M04X04 1 /4 1 /4 0.188 1.188 0.875 0.688 0.719 70M05X02 5 /16 1 /8 0.250 1.000 0.688 0.438 0.688 70M06X04 3 /8 1 /4 0.312 1.156 0.844 0.500 0.875 70M08X06 1 /2 3 /8 0.406 1.344 1.031 0.625 0.906 70M08X08 1 /2 1 /2 0.406 1.437 1.125 0.688 1.188 70M10X08 5 /8 1 /2 0.531 1.688 1.375 1.188 1.172 STYLE 71M Male Run Tee 71M02X02 1 /8 1 /8 0.093 0.937 0.625 0.312 0.688 71M03X02 3 /16 1 /8 0.125 0.937 0.625 0.312 0.688 71M04X02 1 /4 1 /8 0.188 1.000 0.688 0.375 0.750 71M05X02 5 /16 1 /8 0.250 0.969 0.656 0.438 0.750 71M06X04 3 /8 1 /4 0.312 1.094 0.781 0.500 0.938 71M08X06 1 /2 3 /8 0.406 1.250 0.938 0.625 1.093 D STYLE 72M Male ranch Tee D 72M02X02 1 /8 1 /8 0.093 0.937 0.625 0.312 0.688 72M03X02 3 /16 1 /8 0.125 0.937 0.625 0.312 0.688 72M04X02 1 /4 1 /8 0.188 1.000 0.688 0.375 0.750 72M04X04 1 /4 1 /4 0.188 1.031 0.719 0.500 0.938 72M05X02 5 /16 1 /8 0.250 0.969 0.656 0.438 0.750 72M06X04 3 /8 1 /4 0.312 1.094 0.781 0.500 0.938 72M08X06 1 /2 3 /8 0.406 1.250 0.938 0.625 1.093 72M08X08 1 /2 1 /2 0.406 1.312 1.000 0.812 1.344 72M10X08 5 /8 1 /2 0.531 1.469 1.110 0.812 1.280 72M12X08 3 /4 1 /2 0.656 1.734 1.312 1.000 1.406 STYLE 73M Elbow heck 73M02X02 1 /8 1 /8 0.093 0.937 0.625 0.375 0.688 73M03X02 3 /16 1 /8 0.125 0.937 0.625 0.375 0.688 73M04X02 1 /4 1 /8 0.188 0.969 0.656 0.375 0.750 73M06X04 3 /8 1 /4 0.312 1.094 0.781 0.500 0.938 D 58
ompresamatic Flareless Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size D E STYLE 74M 45 Male Elbow 74M08X06 1 /2 3 /8 0.406 1.000 0.688 0.625 0.875 74M10X08 5 /8 1 /2 0.531 1.312 0.940 0.812 1.170 D STYLE 76M Tee E D 76M02X02 1 /8 1 /8 0.093 1.031 0.719 0.562 0.688 0.531 76M04X02 1 /4 1 /8 0.188 1.093 0.781 0.562 0.719 0.531 76M06X04 3 /8 1 /4 0.312 1.250 0.938 0.750 0.844 0.750 STYLE 80M Straight Through Tank Fitting 80M04X04 1 /4 1 /4 0.257 1.375 1.062 0.562 80M06X06 3 /8 3 /8 0.382 1.469 1.156 0.688 80M06X08 3 /8 1 /2 0.382 1.688 1.375 0.875 80M08X08 1 /2 1 /2 0.516 1.750 1.438 0.875 STYLE 82M ulkhead Union E Straight Thread D ulkhead Thread 82M04 1 /4 0.188 2.238 1.750 0.562 0.688 7 /16-24 82M06 3 /8 0.312 2.366 1.880 0.688 0.625 9 /16-24 59
Tube Fittings 45 Flare Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 41F Union Nut Standard Length 41F02 1 /8 0.750 0.375 41F03 3 /16 0.810 0.437 41F04 1 /4 0.940 0.562 41F05 5 /16 1.120 0.625 41F06 3 /8 1.310 0.750 41F08 1 /2 1.620 0.875 41F10 5 /8 1.880 1.062 41F12 3 /4 2.190 1.250 STYLE 41FS Union Nut Short Length 41FS02 1 /8 0.500 0.375 41FS03 3 /16 0.620 0.437 41FS04 1 /4 0.750 0.562 41FS05 5 /16 0.880 0.625 41FS06 3 /8 1.000 0.750 41FS08 1 /2 1.120 0.875 41FS10 5 /8 1.310 1.062 41FS12 3 /4 1.500 1.250 41FS14 7 /8 1.620 1.500 STYLE 64 opper Seal ap 6403 3 /16 0.156 0.312 6404 1 /4 0.218 0.359 6406 3 /8 0.343 0.531 6408 1 /2 0.406 0.640 6410 5 /8 0.437 0.765 60
45 Flare Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 511GS Short Nut 511GS04 1 /4 0.500 0.562 511GS06 3 /8 0.687 0.750 511GS08 1 /2 0.812 0.875 511GS10 5 /8 1.000 1.062 STYLE 625F opper Flare Gasket 625F03 3 /16 0.310 0.120 625F04 1 /4 0.360 0.190 625F05 5 /16 0.420 0.220 625F06 3 /8 0.550 0.280 625F08 1 /2 0.660 0.410 625F10 5 /8 0.770 0.500 625F12 3 /4 0.950 0.620 STYLE 639F Plug 639F03 3 /16 0.590 0.375 639F04 1 /4 0.690 0.437 639F05 5 /16 0.780 0.500 639F06 3 /8 0.880 0.625 639F08 1 /2 1.060 0.750 639F10 5 /8 1.190 0.875 639F12 3 /4 1.310 1.062 STYLE 640F ap Nut 640F03 3 /16 0.470 0.500 640F04 1 /4 0.530 0.562 640F05 5 /16 0.620 0.625 640F06 3 /8 0.690 0.750 640F08 1 /2 0.840 0.875 640F10 5 /8 0.970 1.062 640F12 3 /4 1.090 1.312 61
Tube Fittings 45 Flare Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 641F Long Forged Nut 641F04 1 /4 0.940 0.625 641F05 5 /16 0.940 0.687 641F06 3 /8 1.060 0.812 641F08 1 /2 1.190 0.937 641F10 5 /8 1.440 1.062 641F12 3 /4 1.750 1.312 STYLE 641FS Short Forged Nut 641FS03 3 /16 0.530 0.500 641FS04 1 /4 0.590 0.625 641FS05 5 /16 0.620 0.687 641FS06 3 /8 0.690 0.812 641FS08 1 /2 0.810 0.937 641FS10 5 /8 0.940 1.062 641FS12 3 /4 1.120 1.312 STYLE 641FSH Heavy Short Forged Nut 641FSH04 1 /4 0.594 0.750 641FSH06 3 /8 0.688 0.875 641FSH08 1 /2 0.812 1.000 62
45 Flare Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 642F Union 642F02 1 /8 0.078 0.920 0.312 642F03 3 /16 0.125 1.060 0.375 642F04 1 /4 0.188 1.190 0.437 642F05 5 /16 0.250 1.340 0.500 642F06 3 /8 0.281 1.500 0.625 642F08 1 /2 0.406 1.810 0.750 642F10 5 /8 0.500 2.120 0.875 642F12 3 /4 0.625 2.440 1.062 STYLE 643F all heck 643F03X02 3 /16 1 /8 0.125 1.000 0.437 643F04X02 1 /4 1 /8 0.136 1.060 0.437 643F06X04 3 /8 1 /4 0.187 1.440 0.625 643F08X06 1 /2 3 /8 0.250 1.620 0.750 STYLE 644F Union Tee 644F02 1 /8 0.078 0.620 0.312 644F04 1 /4 0.188 0.880 0.437 644F05 5 /16 0.219 0.910 0.437 644F06 3 /8 0.281 1.060 0.500 644F08 1 /2 0.406 1.220 0.625 644F10 5 /8 0.500 1.410 0.812 644F12 3 /4 0.625 1.660 1.000 63
Tube Fittings 45 Flare Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 645F Male ranch Tee 645F04X02 1 /4 1 /8 0.188 0.810 0.780 0.438 645F04X04 1 /4 1 /4 0.188 0.910 0.940 0.437 645F05X04 5 /16 1 /4 0.219 0.970 0.940 0.500 645F06X04 3 /8 1 /4 0.281 1.030 1.060 0.500 645F06X06 3 /8 3 /8 0.281 1.060 1.090 0.625 645F08X04 1 /2 1 /4 0.312 1.220 1.190 0.625 645F08X06 1 /2 3 /8 0.406 1.220 1.120 0.625 645F08X08 1 /2 1 /2 0.406 1.280 1.380 0.812 645F10X08 5 /8 1 /2 0.500 1.410 1.380 0.812 645F12X08 3 /4 1 /2 0.562 1.620 1.500 1.000 STYLE 646F Female onnector 646F03X02 3 /16 1 /8 0.125 0.970 0.562 646F04X02 1 /4 1 /8 0.188 1.030 0.562 646F04X04 1 /4 1 /4 0.188 1.250 0.688 646F05X02 5 /16 1 /8 0.219 1.060 0.562 646F05X04 5 /16 1 /4 0.250 1.280 0.688 646F06X02 3 /8 1 /8 0.275 1.620 0.620 646F06X04 3 /8 1 /4 0.281 1.310 0.688 646F06X06 3 /8 3 /8 0.281 1.380 0.812 646F06X08 3 /8 1 /2 0.281 1.620 1.000 646F06X12 3 /8 3 /4 0.281 1.660 1.250 646F08X04 1 /2 1 /4 0.406 1.410 0.750 646F08X06 1 /2 3 /8 0.406 1.500 0.812 646F08X08 1 /2 1 /2 0.406 1.750 1.000 646F08X12 1 /2 3 /4 0.406 1.810 1.250 646F10X06 5 /8 3 /8 0.500 1.590 0.875 646F10X08 5 /8 1 /2 0.500 1.810 1.000 646F10X12 5 /8 3 /4 0.500 1.910 1.250 646F12X12 3 /4 3 /4 0.625 1.970 1.250 STYLE 648F Male onnector 64 648F03X02 3 /16 1 /8 0.125 1.000 0.438 648F04X02 1 /4 1 /8 0.188 1.060 0.438 648F04X04 1 /4 1 /4 0.188 1.250 0.562 648F04X06 1 /4 3 /8 0.188 1.310 0.688 648F04X08 1 /4 1 /2 0.188 1.560 0.875 648F05X02 5 /16 1 /8 0.219 1.160 0.500 648F05X04 5 /16 1 /4 0.219 1.340 0.562 648F05X06 5 /16 3 /8 0.219 1.380 0.688 648F06X02 3 /8 1 /8 0.219 1.250 0.625 648F06X04 3 /8 1 /4 0.281 1.440 0.625 648F06X06 3 /8 3 /8 0.281 1.440 0.688 648F06X08 3 /8 1 /2 0.281 1.690 0.875 648F06X12 3 /8 3 /4 0.281 1.810 1.062 648F08X02 1 /2 1 /8 0.219 1.440 0.750 648F08X04 1 /2 1 /4 0.312 1.620 0.750 648F08X06 1 /2 3 /8 0.406 1.620 0.750 648F08X08 1 /2 1 /2 0.406 1.810 0.875 648F08X12 1 /2 3 /4 0.406 1.940 1.062 648F10X04 5 /8 1 /4 0.312 1.810 0.875 648F10X06 5 /8 3 /8 0.406 1.810 0.875 648F10X08 5 /8 1 /2 0.500 2.000 0.875 648F10X12 5 /8 3 /4 0.500 2.060 1.062 648F12X08 3 /4 1 /2 0.562 2.190 1.062 648F12X12 3 /4 3 /4 0.625 2.190 1.062
45 Flare Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 649F Male Elbow 649F02X02 1 /8 1 /8 0.078 0.650 0.690 0.375 649F03X02 3 /16 1 /8 0.125 0.750 0.750 0.375 649F04X02 1 /4 1 /8 0.188 0.825 0.780 0.437 649F04X04 1 /4 1 /4 0.188 0.910 0.940 0.500 649F04X06 1 /4 3 /8 0.188 0.940 1.030 0.625 649F05X02 5 /16 1 /8 0.219 0.910 0.780 0.437 649F05X04 5 /16 1 /4 0.219 0.970 0.940 0.437 649F05X06 5 /16 3 /8 0.219 1.000 1.030 0.562 649F06X02 3 /8 1 /8 0.219 1.030 0.910 0.500 649F06X04 3 /8 1 /4 0.281 1.060 1.060 0.500 649F06X06 3 /8 3 /8 0.281 1.060 1.090 0.562 649F06X08 3 /8 1 /2 0.281 1.160 1.280 0.687 649F08X04 1 /2 1 /4 0.312 1.250 1.120 0.687 649F08X06 1 /2 3 /8 0.406 1.220 1.120 0.625 649F08X08 1 /2 1 /2 0.406 1.280 1.380 0.812 649F08X12 1 /2 3 /4 0.406 1.410 1.410 1.000 649F10X06 5 /8 3 /8 0.406 1.410 1.250 0.750 649F10X08 5 /8 1 /2 0.500 1.410 1.380 0.812 649F10X12 5 /8 3 /4 0.500 1.470 1.500 0.937 649F12X08 3 /4 1 /2 0.562 1.620 1.500 0.937 649F12X12 3 /4 3 /4 0.625 1.620 1.620 1.000 STYLE 650F Female Elbow 650F04X02 1 /4 1 /8 0.188 0.880 0.470 0.562 650F04X04 1 /4 1 /4 0.188 0.970 0.660 0.688 650F04X06 1 /4 3 /8 0.188 1.030 0.660 0.875 650F05X04 5 /16 1 /4 0.219 1.030 0.660 0.688 650F06X04 3 /8 1 /4 0.281 1.090 0.690 0.688 650F06X06 3 /8 3 /8 0.281 1.160 0.690 0.875 650F06X08 3 /8 1 /2 0.281 1.250 0.880 1.000 650F08X06 1 /2 3 /8 0.406 1.280 0.750 1.000 650F08X08 1 /2 1 /2 0.406 1.380 0.940 1.000 650F10X08 5 /8 1 /2 0.500 1.660 1.000 1.250 650F10X12 5 /8 3 /4 STYLE 651F Male Run Tee 651F04X02 1 /4 1 /8 0.188 0.880 0.780 0.438 651F04X04 1 /4 1 /4 0.188 0.910 0.940 0.438 651F05X02 5 /16 1 /8 0.219 0.910 0.780 0.438 651F06X04 3 /8 1 /4 0.281 1.060 1.060 0.500 651F06X06 3 /8 3 /8 0.281 1.060 1.090 0.625 651F08X06 1 /2 3 /8 0.406 1.220 1.120 0.625 651F08X08 1 /2 1 /2 0.406 1.280 1.380 0.812 651F10X08 5 /8 1 /2 0.500 1.410 1.380 0.812 STYLE 653F Tee 653F06X04 3 /8 1 /4 0.281 1.120 0.840 0.750 65
Tube Fittings 45 Flare Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 654F 45 Male Elbow 654F03X02 3 /16 1 /8 0.125 0.625 0.656 0.437 654F04X02 1 /4 1 /8 0.187 0.687 0.656 0.437 654F04X04 1 /4 1 /4 0.187 0.750 0.875 0.500 654F05X02 5 /16 1 /8 0.218 0.750 0.656 0.437 654F06X04 3 /8 1 /4 0.281 0.875 0.875 0.500 654F06X06 3 /8 3 /8 0.281 0.875 0.875 0.625 654F08X06 1 /2 3 /8 0.406 1.000 0.875 0.625 654F10X08 5 /8 1 /2 0.500 1.125 1.156 0.812 654F12X08 3 /4 1 /2 0.562 1.312 1.218 1.062 654F12X12 3 /4 3 /4 0.625 1.312 1.218 1.062 STYLE 655F Union Elbow 655F04 1 /4 0.188 0.880 0.437 655F05 5 /16 0.219 0.940 0.437 655F06 3 /8 0.281 1.060 0.500 655F08 1 /2 0.406 1.250 0.687 655F10 5 /8 0.500 1.440 0.812 655F12 3 /4 0.625 1.690 1.000 STYLE 656F Reducing Union 656F04X03 1 /4 x 3 /16 0.125 1.120 0.437 656F05X04 5 /16 x 1 /4 0.188 1.280 0.500 656F06X04 3 /8 x 1 /4 0.188 1.380 0.625 656F08X04 1 /2 x 1 /4 0.188 1.560 0.750 656F08X06 1 /2 x 3 /8 0.281 1.690 0.750 656F10X06 5 /8 x 3 /8 0.281 1.880 0.875 656F10X08 5 /8 x 1 /2 0.406 2.000 0.875 656F12X08 3 /4 x 1 /2 0.406 2.190 1.062 STYLE 657F Reducing Union Elbow 657F08X06 1 /2 x 3 /8 0.281 1.220 1.090 0.625 657F10X08 5 /8 x 1 /2 0.406 1.410 1.280 0.812 STYLE 660F Female Union Part number includes gaskets. 660F04 1 /4 0.250 1.000 0.625 660F06 3 /8 0.375 1.250 0.812 660F08 1 /2 0.500 1.440 0.937 660F10 5 /8 0.625 1.690 1.062 66
45 Flare Tube Fittings Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 661F Reducer 661F04X06 1 /4 x 3 /8 0.250 1.120 0.625 661F04X08 1 /4 x 1 /2 0.250 1.250 0.750 661F05X04 5 /16 x 1 /4 0.188 1.120 0.687 661F05X06 5 /16 x 3 /8 0.281 1.190 0.687 661F06X04 3 /4 x 1 /4 0.188 1.220 0.812 661F06X05 3 /8 x 5 /16 0.219 1.250 0.812 661F06X08 3 /8 x 1 /2 0.375 1.410 0.812 661F08X04 1 /2 x 1 /4 0.188 1.380 0.937 661F08X06 1 /2 x 3 /8 0.281 1.440 0.937 661F08X10 1 /2 x 5 /8 0.500 1.620 0.937 661F08X12 1 /2 x 3 /4 0.500 1.690 1.062 661F10X08 5 /8 x 1 /2 0.406 1.690 1.062 661F12X10 3 /4 x 5 /8 0.500 1.970 1.312 STYLE 662F Long Forged Reducing Nut 662F06X04 3 /8 x 1 /4 1.060 0.812 662F08X06 1 /2 x 3 /8 1.190 0.937 Part Number includes Gaskets STYLE 662FS Short Forged Reducing Nut 662FS06X04 3 /8 x 1 /4 0.690 0.812 662FS06X05 3 /8 x 5 /16 0.690 0.812 662FS08X06 1 /2 x 3 /8 0.810 0.937 662FS10X08 5 /8 x 1 /2 0.940 1.062 STYLE 664F Female oupling 664F04X02 1 /4 1 /8 0.219 0.910 0.625 664F04X04 1 /4 1 /4 0.250 1.030 0.625 664F06X04 3 /8 1 /4 0.344 1.280 0.812 Includes Gasket 67
Tube Fittings 45 Flare Material: rass Min. Wrench Part Tube Pipe Orifice Pad/Hex Style No. O.D. Thread Size STYLE 669F Female Flare Elbow 669F04X04 1 /4 x 1 /4 0.188 0.940 0.780 0.500 Part Number includes Gaskets STYLE 672FS Flare to Solder Union 672FS04X04 1 /4 1 /4 0.188 1.000 0.437 672FS04X06 1 /4 3 /8 0.188 1.000 0.500 672FS06X06 3 /8 3 /8 0.281 1.190 0.625 672FS08X08 1 /2 1 /2 0.406 1.440 0.750 672FS10X10 5 /8 5 /8 0.500 1.750 0.875 STYLE 673FS Swivel Flare Nut to Solder dapter 673FS04 1 /4 1.250 0.937 0.625 673FS06 3 /8 1.437 1.000 0.812 673FS08 1 /2 1.562 1.062 0.937 673FS10 5 /8 1.812 1.188 1.062 dapts hard drawn tubing to a flare. STYLE 679F Female Swivel Elbow 679F06 3 /8 0.281 1.265 1.000 0.500 679F08 1 /2 0.406 1.437 1.218 0.625 68
Hi-Seal Fittings Material: Steel Part Tube Style No. O.D. T1 T2 D STYLE 708FS Fitting ap For capping tube end of any Hi-Seal fitting. (Includes captive sleeve). 708FS04 1 /4 1 /2-20 0.594 0.625 708FS05 5 /16 9 /16-18 0.672 0.688 708FS06 3 /8 5 /8-18 0.750 0.750 708FS08 1 /2 3 /4-16 0.891 0.875 708FS10 5 /8 15 /16-16 1.000 1.125 708FS12 3 /4 1 1 /16-16 1.000 1.250 708FS16 1 1 5 /16-16 1.000 1.500 STYLE 721FS Tubing ap Used with 760FS sleeve and 761FS nut for capping end of tube. STYLE 752FS ross Tube to Tube to Tube to Tube 721FS04 1 /4 1 /2-20 0.281 0.500 721FS05 5 /16 9 /16-18 0.563 0.563 721FS06 3 /8 5 /8-18 0.609 0.625 721FS08 1 /2 3 /4-16 0.656 0.750 721FS10 5 /8 15 /16-16 0.781 0.938 721FS12 3 /4 1 1 /16-16 0.781 1.063 721FS16 1 1 5 /16-16 0.844 1.313 cross Flats 752FS04 1 /4 2.156 1.078 0.750 0.563 752FS06 3 /8 2.781 1.391 0.953 0.750 752FS08 1 /2 3.094 1.547 1.000 0.750 752FS10 5 /8 3.625 1.813 1.188 1.063 752FS12 3 /4 3.625 1.813 1.188 1.063 Part Tube Pipe Style No. O.D. Thread D E F G STYLE 754FS Male 45 Elbow Tube to Male Pipe Thread Swing cross Radius Flats 754FS04X02 1 /4 1 /8 0.953 0.625 0.672 1.359 0.688 0.281 0.563 754FS06X04 3 /8 1 /4 1.234 0.797 0.828 1.703 0.688 0.281 0.563 754FS08X06 1 /2 3 /8 1.328 0.781 0.875 1.813 0.938 0.438 0.875 754FS10X08 5 /8 1 /2 1.563 0.938 1.047 2.234 1..188 0.438 0.875 754FS12X12 3 /4 3 /4 1.688 1.063 1.188 2.375 1.188 0.656 1.313 754FS16X16 1 1 1.875 1.250 1.391 2.828 1.438 0.656 1.313 STYLE 760FS Sleeve 760FS02 1 /8 760FS03 3 /16 760FS04 1 /4 760FS05 5 /16 760FS06 3 /8 760FS08 1 /2 760FS10 5 /8 760FS12 3 /4 760FS14 7 /8 760FS16 1 760FS20 1 1 /4 69
Hi-Seal Fittings Material: Steel Part Tube Style No. O.D. T1 D E F G STYLE 761FS Nut 761FS02 1 /8 3 /8-24 0.516 0.500 761FS03 3 /16 7 /16-20 0.531 0.563 761FS04 1 /4 1 /2-20 0.594 0.625 761FS05 5 /16 9 /16-18 0.672 0.688 761FS06 3 /8 5 /8-18 0.750 0.750 761FS08 1 /2 3 /4-16 0.891 0.875 761FS10 5 /8 15 /16-16 1.000 1.125 761FS12 3 /4 1 1 /16-16 1.000 1.250 761FS14 7 /8 1 3 /16-16 1.000 1.375 761FS16 1 1 5 /16-16 1.000 1.500 STYLE 762FS Union Tube to Tube 762FS02 1 /8 1.344 0.375 0.797 762FS03 3 /16 1.406 0.438 0.797 762FS04 1 /4 1.563 0.500 0.953 762FS05 5 /16 1.781 0.563 0.953 762FS06 3 /8 1.875 0.625 1.063 762FS08 1 /2 2.188 0.750 1.156 762FS10 5 /8 2.500 0.938 1.313 762FS12 3 /4 2.500 1.063 1.313 762FS14 7 /8 2.563 1.188 1.375 762FS16 1 2.563 1.313 1.375 762FS20 1 1 /4 3.063 1.375 1.438 STYLE 764FS Union Tee Tube to Tube to Tube cross Flats 764FS04 1 /4 2.156 1.078 0.750 0.437 764FS06 3 /8 2.844 1.422 0.984 0.625 764FS08 1 /2 3.344 1.672 1.125 0.750 764FS10 5 /8 3.875 1.938 1.313 0.875 764FS12 3 /4 4.125 2.063 1.438 1.063 764FS16 1 4.688 2.344 1.719 1.250 STYLE 765FS Union Elbow Tube to Tube cross Flats 765FS02 1 /8 1.172 0.953 0.656 0.219 0.437 765FS04 1 /4 1.297 1.078 0.750 0.219 0.437 765FS05 5 /16 1.406 1.156 0.750 0.250 0.500 765FS06 3 /8 1.641 1.359 0.922 0.281 0.563 765FS08 1 /2 2.047 1.672 1.125 0.375 0.750 765FS10 5 /8 2.375 1.938 1.313 0.438 0.875 765FS12 3 /4 2.594 2.063 1.438 0.531 1.063 765FS14 7 /8 2.875 2.250 1.625 0.625 1.313 765FS16 1 2.969 2.344 1.719 0.625 1.313 70
Hi-Seal Fittings Material: Steel Part Tube Pipe Style No. O.D. Thread D E F G STYLE 766FS Female onnector Tube to Female Pipe Thread 766FS02X02 1 /8 1 /8 1.141 0.563 0.844 766FS04X02 1 /4 1 /8 1.281 0.563 0.953 766FS04X04 1 /4 1 /4 1.391 0.750 1.063 766FS05X02 5 /16 1 /8 1.359 0.563 0.953 766FS05X04 5 /16 1 /4 1.469 0.750 1.063 766FS06X04 3 /8 1 /4 1.609 0.750 1.172 766FS06X06 3 /8 3 /8 1.672 0.875 1.234 766FS08X04 1 /2 1 /4 1.766 0.750 1.219 766FS08X06 1 /2 3 /8 1.828 0.875 1.281 766FS08X08 1 /2 1 /2 2.109 1.063 1.563 766FS10X08 5 /8 1 /2 2.188 1.063 1.563 766FS12X08 3 /4 1 /2 2.188 1.063 1.563 766FS12X12 3 /4 3 /4 2.281 1.250 1.656 766FS14X12 7 /8 3 /4 2.281 1.250 1.656 766FS16X16 1 1 2.500 1.625 1.875 STYLE 767FS Female Run Tee Tube to Female Pipe Thread to Tube cross Swing ody Flats Radius (SR) 767FS04X02 1 /4 1 /8 1.797 1.109 0.781 0.688 0.500 0.859 767FS04X04 1 /4 1 /4 2.109 1.219 0.891 0.828 0.688 0.953 767FS06X04 3 /8 1 /4 2.391 1.516 1.078 0.875 0.750 1.172 767FS08X06 1 /2 3 /8 2.672 1.734 1.188 0.938 0.875 1.297 767FS12X12 3 /4 3 /4 3.500 2.125 1.500 1.375 1.250 1.641 767FS16X16 1 1 3.875 2.250 1.625 1.625 1.625 1.797 STYLE 768FS Male onnection Tube to Male Pipe Thread 768FS02X02 1 /8 1 /8 1.141 0.437 0.844 768FS03X02 3 /16 1 /8 1.172 0.437 0.844 768FS04X02 1 /4 1 /8 1.281 0.500 0.953 768FS04X04 1 /4 1 /4 1.484 0.625 1.156 768FS04X06 1 /4 3 /8 1.453 0.750 1.125 768FS04X08 1 /4 1 /2 1.828 0.875 1.500 768FS05X02 5 /16 1 /8 1.359 0.563 0.953 768FS05X04 5 /16 1 /4 1.563 0.625 1.156 768FS06X02 3 /8 1 /8 1.438 0.625 1.000 768FS06X04 3 /8 1 /4 1.641 0.625 1.203 768FS06X06 3 /8 3 /8 1.641 0.750 1.203 768FS06X08 3 /8 1 /2 1.969 0.875 1.531 768FS06X12 3 /8 3 /4 1.984 1.125 1.547 768FS08X06 1 /2 3 /8 1.797 0.750 1.250 768FS08X08 1 /2 1 /2 2.141 0.875 1.594 768FS08X12 1 /2 3 /4 2.109 1.125 1.563 768FS10X06 5 /8 3 /8 1.969 0.938 1.344 768FS10X08 5 /8 1 /2 2.250 0.938 1.625 768FS10X12 5 /8 3 /4 2.219 1.063 1.406 768FS12X06 3 /4 3 /8 2.031 1.063 1.406 768FS12X08 3 /4 1 /2 2.250 1.125 1.625 768FS12X12 3 /4 3 /4 2.250 1.125 1.625 768FS14X12 7 /8 3 /4 2.250 1.250 1.625 768FS16X12 1 3 /4 2.250 1.375 1.625 768FS16X16 1 1 2.438 1.375 1.813 71
Hi-Seal Fittings Material: Steel Swing Part Tube Pipe Radius Style No. O.D. Thread D E F (SR) STYLE 769FS Male Elbow Tube to Male Pipe Thread 769FS02X02 1 /8 1 /8 1.172 0.953 0.656 0.750 0.219 0.437 0.688 769FS03X02 3 /16 1 /8 1.203 0.984 0.656 0.750 0.219 0.437 0.734 769FS04X02 1 /4 1 /8 1.297 1.078 0.750 0.781 0.219 0.437 0.828 769FS04X04 1 /4 1 /4 1.484 1.203 0.875 1.063 0.281 0.563 0.969 769FS04X06 1 /4 3 /8 1.641 1.203 0.875 0.969 1.156 0.437 0.750 769FS05X02 5 /16 1 /8 1.406 1.156 0.750 0.781 0.250 0.500 0.844 769FS05X04 5 /16 1 /4 2.563 1.281 0.875 1.094 0.281 0.563 0.969 769FS06X02 3 /8 1 /8 1.641 1.359 0.922 0.875 0.281 0.563 1.016 769FS06X04 3 /8 1 /4 1.641 1.359 0.922 1.094 0.281 0.563 1.016 769FS06X06 3 /8 3 /8 1.922 1.359 1.109 1.219 0.375 0.750 1.172 769FS06X08 3 /8 1 /2 2.000 1.563 1.125 1.250 0.438 0.750 1.313 769FS06X12 3 /8 3 /4 2.172 1.641 1.203 1.594 0.531 1.063 1.281 769FS08X04 1 /2 1 /4 2.047 1.672 1.125 1.094 0.375 0.750 1.234 769FS08X06 1 /2 3 /8 2.047 1.672 1.125 1.219 0.375 0.750 1.234 769FS08X08 1 /2 1 /2 2.047 1.672 1.125 1.250 0.375 0.750 1.938 769FS08X12 1 /2 3 /4 2.328 1.797 1.250 1.594 1.219 1.063 1.359 769FS10X06 5 /8 3 /4 2.375 1.938 1.313 1.219 0.438 0.875 1.438 769FS10X08 5 /8 1 /2 2.375 1.938 1.313 1.469 0.438 0.875 1.438 769FS12X08 3 /4 1 /2 2.594 2.063 1.438 1.563 0.531 1.063 1.625 769FS12X12 3 /4 3 /4 2.594 2.063 1.438 1.594 0.531 1.063 1.625 769FS14X12 7 /8 3 /4 2.875 2.250 1.625 1.688 0.625 1.250 1.719 769FS16X12 1 3 /4 2.969 2.344 1.719 1.688 0.625 1.250 1.859 769FS16X16 1 1 2.969 2.344 1.719 1.969 0.625 1.250 1.859 STYLE 770FS Female Elbow Tube to Female Pipe Tube 770FS04X02 1 /4 1 /8 1.359 1.109 0.781 0.688 0.250 0.500 0.859 770FS04X04 1 /4 1 /4 1.703 1.328 1.000 0.875 0.375 0.750 1.078 770FS06X04 3 /8 1 /4 1.922 1.547 1.109 0.875 0.375 0.750 1.203 770FS06X06 3 /8 3 /8 2.063 1.578 1.078 0.938 0.438 0.875 1.234 770FS06X08 3 /8 1 /2 2.031 1.500 1.063 1.188 0.531 1.063 1.313 770FS08X06 1 /2 3 /8 2.016 1.703 1.156 0.938 0.438 0.875 1.266 770FS08X08 1 /2 1 /2 2.328 1.797 1.313 1.188 0.531 1.063 1.359 770FS10X08 5 /8 1 /2 2.469 1.938 1.313 1.266 0.531 1.063 1.438 770FS12X08 3 /4 1 /2 2.469 1.938 1.313 1.188 0.531 1.063 1.469 770FS12X12 3 /4 3 /4 2.750 2.125 1.500 1.375 0.625 1.250 1.641 770FS16X16 1 1 3.063 2.250 1.625 1.625 0.203 1.625 1.797 STYLE 771FS Male Run Tee Tube to Male Pipe Thread to Tube Swing cross Radius Flats (SR) 771FS04X02 1 /4 1 /8 1.859 0.781 0.750 1.078 0.438 0.828 771FS04X04 1 /4 1 /4 2. 047 0.938 0.781 1.109 0.500 0.828 771FS06X04 3 /8 1 /4 2.484 1.063 0.828 1.422 0.625 1.078 771FS08X06 1 /2 3 /8 2 859 1.188 1.125 1.703 0.750 1.234 771FS08X08 1 /2 1 /2 3.141 1.375 1.219 1.766 0.875 1.750 771FS12X12 3 /4 3 /4 3.625 1.563 1.438 2.063 1.063 1.625 72
Hi-Seal Fittings Material: Steel Swing Part Tube Pipe Radius Style No. O.D. Thread D E (SR) STYLE 772FS Male ranch Tee Tube to Tube to Male Pipe Thread cross Flats 772FS04X02 1 /4 1 /8 2.156 1.078 0.750 0.781 0.437 0.828 772FS04X04 1 /4 1 /4 2.219 1.109 0.781 0.938 0.500 0.859 772FS05X02 5 /16 1 /8 2.438 1.219 0.813 0.781 0.500 0.906 772FS06X04 3 /8 1 /4 2.844 1.422 0.984 1.063 0.625 1.078 772FS08X06 1 /2 3 /8 3.344 1.672 1.125 1.188 0.750 1.234 772FS08X08 1 /2 1 /2 3.531 1.766 1.219 1.375 0.875 1.750 772FS10X08 5 /8 1 /2 3.875 1.938 1.313 1.438 0.875 1.438 772FS12X12 3 /4 3 /4 4.125 2.063 1.438 1.563 1.063 1.625 STYLE 777FS Female ranch Tee Tube to Tube to Female Pipe Thread Swing cross Radius Flats (SR) 777FS06X04 3 /8 1 /4 3.031 1.516 1.078 0.875 0.750 1.172 777FS08x06 1 /2 3 /8 3.469 1.734 1.188 0.938 0.875 1.297 777FS10X08 5 /8 1 /2 3.875 1.938 1.313 1.188 1.063 1.438 777FS12X12 3 /4 3 /4 4.250 2.125 1.500 1.375 1.250 1.641 777FS16X16 1 1 4.500 2.250 1.625 1.625 1.625 1.797 Part Tube Style No. O.D. T1 D E STYLE 782FS ulkhead Union Tube to Tube Max. ulkhead 782FS04 1 /4 1 /2-20 2.219 0.688 1.563 0.375 782FS06 3 /8 5 /8-18 2.531 0.813 1.656 0.375 782FS08 1 /2 3 /4-16 2.844 0.938 1.750 0.375 782FS12 3 /4 1 1 /16-16 3.438 1.250 2.188 0.625 Part Tube O.D. Style No. Hi-Seal N T1 T2 D E STYLE 792FS dapter Hi-Seal to N Thread Drill Drill 792FS04 1 /4 1 /4 1 /2-20 7 /16-20 1.406 0.688 1.078 0.203 0.172 792FS06 3 /8 3 /8 5 /8-18 9 /16-18 1.766 0.688 1.203 0.281 0.297 792FS08 1 /2 1 /2 3 /4-16 3 /4-16 1.891 1.000 1.344 0.422 0.391 792FS16 1 1 1 5 /16-16 1 5 /16-12 2.781 1.625 1.766 0.750 0.844 73
Hi-Seal Fittings Material: Steel/O-Ring Part Tube Style No. O.D. T1 D E F G STYLE 768FSO Male onnector Tube to Straight Thread 768FSO04 1 /4 7 /16-20 1.203 1.563 0.875 0.359 768FSO06 3 /8 9 /16-18 1.453 0.688 1.016 0.391 768FSO08 1 /2 3 /4-16 1.672 0.875 1.125 0.438 768FSO10 5 /8 7 /8-14 1.906 1.000 1.281 0.500 768FSO12 3 /4 1 1 /16-12 2.063 1.250 1.438 0.594 768FSO14 7 /8 1 3 /16-12 2.063 1.375 1.438 0.594 768FSO16 1 15 5 /16-12 2.063 1.500 1.438 0.594 STYLE 769FSO Male Elbow Tube to Straight Thread Swing cross Radius Flats (SR) 769FSO04 1 /4 7 /16-20 1.297 1.078 0.750 1.266 0.219 1.078 0.437 0.828 769FSO06 3 /8 9 /16-18 1.625 1.344 0.906 1.828 0.281 1.250 0.563 0.828 769FSO08 1 /2 3 /4-16 1.922 1.547 1.000 1.813 0.375 1.438 0.750 1.125 769FSO10 5 /8 7 /8-14 2.344 1.906 1.281 2.125 0.438 1.688 0.875 1.406 769FSO12 3 /4 1 1 /16-12 2.609 2.078 1.906 2.469 0.531 1.938 1.063 1.625 769FSO14 7 /8 1 3 /16-12 2.875 2.250 1.625 2.656 0.625 2.031 1.250 1.781 769FSO16 1 1 5 /16-12 2.969 2.344 1.719 2.656 0.625 2.031 1.250 1.859 STYLE 771FSO Male Run Tee Tube to Straight Thread to Tube Swing cross Radius Flats (SR) 771FSO04 1 /4 7 /16-20 2.156 1.094 0.750 1.063 0.563 0.828 771FSO06 3 /8 9 /16-18 2.688 1.438 1.000 1.250 0.563 1.078 771FSO08 1 /2 3 /4-16 3.141 1.688 1.141 1.453 0.750 1.234 STYLE 772FSO Male ranch Tee Tube to Tube to Straight Thread Swing cross Radius Flats (SR) 772FSO04 1 /4 7 /16-20 2.625 1.078 0.750 1.047 0.437 0.828 772FSO06 3 /8 9 /16-18 2.844 1.422 0.984 1.234 0.563 1.078 772FSO12 3 /4 1 1 /16-12 4.125 2.063 1.438 1.938 1.063 1.625 74
Hi-Seal Fittings Material: Stainless Steel Part Tube Style No. O.D. T1 D E F G STYLE 708FSS Fitting ap 708FSS02 1 /8 3 /8-24 0.516 0.500 708FSS04 1 /4 1 /2-20 0.594 0.625 708FSS06 3 /8 5 /8-18 0.750 0.750 708FSS08 1 /2 3 /4-16 0.891 0.875 708FSS10 5 /8 15 /16-16 1.000 1.125 708FSS12 3 /4 1 1 /16-16 1.000 1.250 STYLE 711FSS Lock Nut 711FSS04 1 /4 1 /2-20 0.250 0.688 711FSS06 3 /8 5 /8-18 0.250 0.813 T1 STYLE 721FSS Tubing ap 721FSS04 1 /4 1 /2-20 0.281 0.500 721FSS06 3 /8 5 /8-18 0.609 0.625 721FSS08 1 /2 3 /4-16 0.656 0.750 721FSS12 3 /4 1 1 /16-16 0.781 1.063 STYLE 722FSS dapter Straight Tube to Male Pipe Thread 722FSS04X04 1 /4 1 /4 1.438 0.563 0.625 722FSS06X04 3 /8 1 /4 1.563 0.563 0.750 722FSS08X04 1 /2 1 /4 1.625 0.563 0.813 STYLE 752FSS ross Tube to Tube to Tube to Tube cross Flats 752FSS04 1 /4 2.031 1.016 0.688 0.500 752FSS06 3 /8 2.719 1.359 0.922 0.750 752FSS08 1 /2 3.031 1.516 0.969 0.750 75
Hi-Seal Fittings Material: Stainless Steel Part Tube Pipe Style No. O.D. Thread D E F G STYLE 754FSS Male 45 Elbow Tube to Male Pipe Thread Swing cross Radius Flats 754FSS04X02 1 /4 1 /8 0.859 0.531 0.625 1.203 0.656 0.219 0.438 754FSS06X04 3 /8 1 /4 1.078 0.641 0.750 1.547 0.875 0.250 0.500 754FSS08X06 1 /2 3 /8 1.234 0.688 0.828 1.484 0.875 0.313 0.375 STYLE 756FSS Reducing Union Tube to Tube T1 T2 756FSS04X02 1 /4 x 1 /8 1.469 0.625 0.844 0.203 0.156 1 /2-20 3 /8-24 756FSS06X04 3 /8 x 1 /4 1.688 0.750 0.922 0.281 0.203 5 /8-18 1 /2-20 756FSS08X04 1 /2 x 1 /4 1.875 0.875 1.000 0.422 0.203 3 /4-16 1 /2-20 756FSS08X06 1 /2 x 3 /8 2.000 0.875 1.016 0.422 0.281 3 /4-16 5 /8-18 STYLE 760FSS Sleeve 760FSS02 1 /8 760FSS03 3 /16 760FSS04 1 /4 760FSS05 5 /16 760FSS06 3 /8 760FSS08 1 /2 760FSS10 5 /8 760FSS12 3 /4 760FSS16 1 STYLE 760FT Teflon Sleeve 760FT02 1 /8 760FT04 1 /4 STYLE 760FPH Sleeve 17-4 PH 760FPH02 1 /8 760FPH04 1 /4 760FPH06 3 /8 760FPH08 1 /2 760FPH12 3 /4 760FPH16 1 Teflon is a registered trademark of E.I.DuPont DeNemours &o., Inc. 76
Hi-Seal Fittings Material: Stainless Steel Part Tube Style No. O.D. T1 D E F G STYLE 761FSS Nut 761FSS02 1 /8 3 /8-24 0.516 0.500 761FSS03 3 /16 7 /16-20 0.531 0.563 761FSS04 1 /4 1 /2-20 0.594 0.625 761FSS05 5 /16 9 /16-18 0.672 0.688 761FSS06 3 /8 5 /8-18 0.750 0.750 761FSS08 1 /2 3 /4-16 0.891 0.875 761FSS10 5 /8 15 /16-16 1.000 1.125 761FSS12 3 /4 1 1 /16-16 1.000 1.250 761FSS16 1 1 5 /16-16 1.000 1.500 Part Tube Pipe Style No. O.D. Thread D E F G STYLE 762FSS Lock Nut 762FSS01 1 /16 1.156 0.250 0.625 762FSS02 1 /8 1.344 0.375 0.797 762FSS03 3 /16 1.406 0.437 0.797 762FSS04 1 /4 1.563 0.500 0.953 762FSS05 5 /16 1.781 0.563 0.953 762FSS06 3 /8 1.875 0.625 1.063 762FSS08 1 /2 2.188 0.750 1.156 762FSS10 5 /8 2.500 0.938 1.156 762FSS12 3 /4 2.500 1.063 1.156 762FSS14 7 /8 2.563 1.188 1.375 762FSS16 1 2.563 1.563 1.375 STYLE 764FSS Union Tee Tube to Tube to Tube cross Flats 764FSS02 1 /8 1.781 0.891 0.594 0.375 764FSS04 1 /4 2.094 1.047 0.719 0.437 764FSS05 5 /16 2.375 1.188 0.781 0.500 764FSS06 3 /8 2.469 1.234 0.797 0.500 764FSS08 1 /2 2.969 1.484 0.938 0.625 764FSS10 5 /8 3.875 1.938 1.313 1.000 764FSS12 3 /4 4.125 2.063 1.438 1.000 764FSS16 1 3.875 1.938 1.313 1.313 STYLE 765FSS Union Elbow Tube to Tube cross Flats 765FSS02 1 /8 1.109 0.953 0.656 0.156 0.375 765FSS04 1 /4 1.266 1.047 0.719 0.219 0.437 765FSS05 5 /16 1.438 1.188 0.781 0.250 0.500 765FSS06 3 /8 1.516 1.266 0.828 0.250 0.500 765FSS08 1 /2 1.797 1.484 0.938 0.313 0.625 765FSS10 5 /8 2.438 1.938 1.313 0.500 1.000 765FSS12 3 /4 2.563 2.063 1.438 0.500 1.000 765FSS16 1 2.594 1.938 1.313 0.656 1.313 77
Hi-Seal Fittings Material: Stainless Steel Part Tube Pipe Style No. O.D. Thread D E F G STYLE 766FSS Female onnector Tube to Female Pipe Thread 766FSS02X02 1 /8 1 /8 1.141 0.563 0.844 766FSS04X02 1 /4 1 /8 1.281 0.563 0.953 766FSS04X04 1 /4 1 /4 1.391 0.750 1.063 766FSS05X04 5 /16 1 /4 1.469 0.750 1.063 766FSS06X02 3 /8 1 /8 1.438 0.625 1.000 766FSS06X04 3 /8 1 /4 1.609 0.750 1.172 766FSS06X06 3 /8 3 /8 1.672 0.875 1.234 766FSS06X08 3 /8 1 /2 1.938 1.063 1.500 766FSS08X04 1 /2 1 /4 1.766 0.750 1.219 766FSS08X06 1 /2 3 /8 1.828 0.875 1.281 766FSS08X08 1 /2 1 /2 2.109 1.063 1.563 766FSS10X08 5 /8 1 /2 2.188 1.063 1.563 766FSS12X12 3 /4 3 /4 2.281 1.250 1.656 766FSS16X16 1 1 2.500 1.625 1.875 STYLE 767FSS Female Run Tee Tube to Female Pipe Thread to Tube Swing cross Radius Flats (SR) 767FSS04X04 1 /4 1 /4 2.063 1.172 0.844 0.891 0.750 0.938 767FSS06X04 3 /8 1 /4 2.203 1.313 0.875 0.891 0.750 0.984 STYLE 768FSS Male onnector Tube to Male Pipe Thread 768FSS02X02 1 /8 1 /8 1.141 0.437 0.844 768FSS02X04 1 /8 1 /4 1.391 0.563 1.094 768FSS03X02 3 /16 1 /8 1.172 0.437 0.844 768FSS04X02 1 /4 1 /8 1.281 0.500 0.953 768FSS04X04 1 /4 1 /4 1.484 0.625 1.156 768FSS04X06 1 /4 3 /8 1.453 0.750 1.125 768FSS04X08 1 /4 1 /2 1.828 0.875 1.500 768FSS05X02 5 /16 1 /8 1.359 0.563 0.953 768FSS05X04 5 /16 1 /4 1.563 0.625 1.156 768FSS06X02 3 /8 1 /8 1.438 0.625 1.000 768FSS06X04 3 /8 1 /4 1.641 0.625 1.203 768FSS06X06 3 /8 3 /8 1.641 0.750 1.203 768FSS06X08 3 /8 1 /2 1.969 0.875 1.531 768FSS06X12 3 /8 3 /4 1.984 1.125 1.547 768FSS08X04 1 /2 1 /4 1.797 0.750 1.250 768FSS08X06 1 /2 3 /8 1.797 0.750 1.250 768FSS08X08 1 /2 1 /2 2.141 0.875 1.594 768FSS08X12 1 /2 3 /4 2.109 1.125 1.563 768FSS10X08 5 /8 1 /2 2.250 0.938 1.625 768FSS12X08 3 /4 1 /2 2.250 1.125 1.625 768FSS12X12 3 /4 3 /4 2.250 1.125 1.625 768FSS16X12 1 3 /4 2.250 1.375 1.625 78
Hi-Seal Fittings Material: Stainless Steel Part Tube Pipe Style No. O.D. Thread D E F G STYLE 769FSS Male Elbow Tube to Male Pipe Thread Swing cross Radius Flats (SR) 769FSS02X02 1 /8 1 /8 1.109 0.922 0.625 0.719 0.188 0.375 0.656 769FSS02X04 1 /8 1 /4 1.203 0.984 0.688 1.031 0.219 0.437 0.719 769FSS04X02 1 /4 1 /8 1.234 1.016 0.672 0.781 0.219 0.437 0.813 769FSS04X04 1 /4 1 /4 1.297 1.078 0.750 1.094 0.219 0.437 0.828 769FSS05X02 5 /16 1 /8 1.375 1.125 0.719 0.844 0.250 0.500 0.828 769FSS05X04 5 /16 1 /4 1.406 1.156 0.750 0.938 0.250 0.500 0.844 769FSS06X02 3 /8 1 /8 1.422 1.172 0.734 0.813 0.250 0.563 0.844 769FSS06X04 3 /8 1 /4 1.484 1.234 0.797 1.063 0.250 0.500 0.906 769FSS06X06 3 /8 3 /8 1.578 1.297 0.859 1.063 0.281 0.563 0.969 769FSS06X08 3 /8 1 /2 1.734 1.391 0.953 1.250 0.344 0.688 1.000 769FSS08X04 1 /2 1 /4 1.766 1.453 0.906 1.125 0.313 0.625 1.031 769FSS08X06 1 /2 3 /8 1.766 1.453 0.906 1.125 0.313 0.625 1.031 769FSS08X08 1 /2 1 /2 1.828 1.484 0.938 1.313 0.344 0.688 1.063 769FSS10X08 5 /8 1 /2 2.094 1.656 1.031 1.500 0.438 0.875 1.188 769FSS12X12 3 /4 3 /4 2.219 1.750 1.125 1.469 0.469 0.938 1.328 769FSS16X16 1 1 2.594 1.938 1.313 1.969 0.656 1.313 1.516 STYLE 770FSS Female Elbow Tube to Female Pipe Tube Swing cross Radius Flats (SR) 770FSS04X02 1 /4 1 /8 1.359 1.109 0.781 0.688 0.250 0.500 0.859 770FSS04X04 1 /4 1 /4 1.703 1.328 1.000 0.875 0.375 0.750 1.078 770FSS06X04 3 /8 1 /4 1.922 1.547 1.109 0.875 0.375 0.750 1.203 770FSS06X06 3 /8 3 /8 2.063 1.578 1.141 0.938 0.438 0.875 1.234 770FSS08X06 1 /2 3 /8 2.016 1.703 1.156 1.313 0.438 0.875 1.266 770FSS08X08 1 /2 1 /2 2.328 1.797 1.313 1.188 0.531 1.063 1.359 79
Hi-Seal Fittings Material: Stainless Steel Part Tube Pipe Style No. O.D. Thread D E G STYLE 771FSS Male Run Tee Tube to Male Pipe Thread to Tube Swing cross Radius Flats (SR) 771FSS01X02 1 /16 1 /8 1.766 0.859 0.688 0.906 0.437 0.797 771FSS02X02 1 /8 1 /8 1.703 0.750 0.656 0.953 0.437 0.734 771FSS03X02 3 /16 1 /8 1.734 0.750 0.656 0.984 0.437 0.734 771FSS04X02 1 /4 1 /8 1.859 0.781 0.750 1.078 0.437 0.828 771FSS04X04 1 /4 1 /4 2.049 0.938 0.781 1.109 0.500 0.859 771FSS05X02 5 /16 1 /8 2.000 0.781 0.813 1.219 0.500 0.906 771FSS06X04 3 /8 1 /4 2.484 1.063 0.984 1.422 0.625 1.078 771FSS08X06 1 /2 3 /8 2.859 1.188 1.125 1.672 0.750 1.234 771FSS08X08 1 /2 1 /2 3.141 1.375 1.219 1.766 0.875 1.750 771FSS10X08 5 /8 1 /2 3.375 1.438 1.938 2.063 1.875 1.438 771FSS12X12 3 /4 3 /4 3.625 1.563 1.438 2.063 1.063 1.625 771FSS14X12 7 /8 3 /4 3.938 1.688 1.625 2.250 1.250 1.781 771FSS16X16 1 1 4.281 1.938 1.719 2.344 1.250 1.859 771FSS20X20 1 1 /4 1 1 /4 4.938 2.313 1.813 2.625 1.625 2.078 STYLE 772FSS Male ranch Tee Tube to Tube to Male Pipe Thread cross Swing Flats Radius 772FSS04X02 1 /4 1 /8 2.094 1.047 0.719 0.750 0.437 0.813 772FSS04X04 1 /4 1 /4 2.156 1.078 0.750 0.938 0.437 0.828 772FSS06X04 3 /8 1 /4 2.531 1.266 0.859 1.000 0.500 0.938 772FSS08X06 1 /2 3 /8 2.656 1.484 0.938 1.063 0.625 1.063 772FSS08X08 1 /2 1 /2 3.406 1.703 1.156 1.344 0.813 1.219 80
Hi-Seal Fittings Material: Stainless Steel Part Tube Pipe Style No. O.D. Thread D E G STYLE 777FSS Female ranch Tee Tube to Tube to Female Pipe Thread Swing Radius (SR) 777FSS04X04 1 /4 1 /4 2.344 1.172 0.844 0.891 0.750 0.938 777FSS06X04 3 /8 1 /4 2.625 1.313 0.875 0.891 0.750 0.984 777FSS08X06 1 /2 3 /8 3.094 1.547 1.000 0.969 0.813 1.125 STYLE 780FSS Thermocouple onnector 780FSS02X02 1 /8 1 /8 1.141 0.437 0.844 780FSS03X02 3 /16 1 /8 1.172 0.437 0.844 780FSS03X04 3 /16 1 /4 1.422 0.563 1.094 780FSS04X02 1 /4 1 /8 1.281 0.500 0.953 780FSS04X04 1 /4 1 /4 1.484 0.625 1.156 780FSS06X06 3 /8 3 /8 1.641 0.750 1.203 780FSS08X08 1 /2 1 /2 2.141 0.875 1.594 81
Hi-Seal Fittings Material: Stainless Steel Part Tube Style No. O.D. T1 D E F STYLE 782FSS ulkhead Union Tube to Tube Max. ulkhead ulkhead Thread 782FSS04 1 /4 1 /2-20 2.219 0.688 1.563 0.375 1 /2-20 782FSS06 3 /8 5 /8-18 2.531 0.813 1.656 0.375 5 /8-18 782FSS08 1 /2 3 /4-16 2.844 0.938 1.750 0.375 3 /4-16 STYLE 786FSS ulkhead Female onnector Tube to Female Pipe Thread Max. ulkhead ulkhead Thread 786FSS04X04 1 /4 1 /4 2.016 0.688 0.750 1.688 0.375 1 /2-20 786FSS06X04 3 /8 1 /4 2.172 0.813 0.750 1.734 0.375 5 /8-18 STYLE 788FSS ulkhead Male onnector Tube to Male Pipe Thread Max. ulkhead ulkhead Thread 788FSS04X04 1 /4 1 /4 2.109 0.688 0.688 1.781 0.375 1 /2-20 82
Sleeves & Nuts Hi-Seal raze-seal Fittings Material: Steel & Stainless Steel Part Tube Style No. O.D. T1 STYLE 760FSZ raze-seal Sleeve Material: Steel 760FSZ04 1 /4 0.250 760FSZ06 3 /8 0.281 760FSZ08 1 /2 0.313 760FSZ12 3 /4 0.500 760FSZ14 7 /8 0.500 760FSZ16 1 0.563 760FSZ24 1 1 /2 0.750 STYLE 760FSSZ raze-seal Sleeve Material: Stainless Steel 760FSSZ04 1 /4 0.250 760FSSZ06 3 /8 0.281 760FSSZ08 1 /2 0.313 STYLE 761FSZ raze-seal Nut Material: Steel 761FSZ04 1 /4 1 /2-20 0.656 0.625 761FSZ06 3 /8 5 /8-18 0.766 0.750 761FSZ08 1 /2 3 /4-16 0.813 0.875 761FSZ12 3 /4 1 1 /16-16 1.000 1.250 761FSZ14 7 /8 1 3 /16-16 1.000 1.375 761FSZ16 1 1 5 /16-16 1.063 1.500 761FSZ24 1 1 /2 1 7 /8-16 1.281 2.250 STYLE 761FSSZ raze-seal Nut Material: Stainless Steel 761FSSZ04 1 /4 1 /2-20 0.656 0.625 761FSSZ06 3 /8 5 /8-18 0.766 0.750 761FSSZ08 1 /2 3 /4-16 0.813 0.875 761FSSZ10 5 /8 15 /16-16 0.859 1.125 761FSSZ12 3 /4 1 1 /16-16 1.000 1.250 83
Hi-Seal Fittings Material: rass Part Tube Style No. O.D. T1 D E F G STYLE 708F Fitting ap 708F04 1 /4 1 /2-20 0.594 0.625 708F06 3 /8 5 /8-18 0.750 0.750 708F08 1 /2 3 /4-16 0.891 0.875 708F10 5 /8 15 /16-16 1.000 1.125 STYLE 711F Lock Nut T1 711F04 1 /4 1 /2-20 0.172 0.688 711F06 3 /8 5 /8-18 0.172 0.813 711F08 1 /2 3 /4-16 0.172 0.938 STYLE 721F Tubing ap 721F04 1 /4 1 /2-20 0.281 0.500 721F06 3 /8 5 /8-18 0.609 0.625 721F08 1 /2 3 /4-16 0.656 0.750 STYLE 754F Male 45 Elbow Tube to Male Pipe Thread Swing cross Radius Flats 754F04X02 1 /4 1 /8 0.859 0.531 0.625 1.203 0.656 0.437 754F04X04 1 /4 1 /4 0.891 0.563 0.625 1.500 0.875 0.500 754F05X02 5 /16 1 /8 1.000 0.594 0.688 1.328 0.719 0.500 754F06X04 3 /8 1 /4 1.078 0.641 0.750 1.547 0.875 0.500 754F08X06 1 /2 3 /8 1.234 0.688 0.828 1.547 0.875 0.625 STYLE 756F Reducing UnionTube to Tube T1 T2 756F04X02 1 /4 x 1 /8 1.469 0.625 0.844 0.203 0.156 1 /2-20 3 /8-24 756F06X04 3 /8 x 1 /4 1.688 0.750 0.922 0.281 0.203 5 /8-18 1 /2-20 756F08X04 1 /2 x 1 /4 1.875 0.875 1.000 0.422 0.203 3 /4-16 1 /2-20 756F08X06 1 /2 x 3 /8 2.000 0.875 1.016 0.422 0.281 3 /4-16 5 /8-18 756F12X08 3 /4 x 1 /2 2.391 1.250 1.219 0.656 0.422 1 1 /16-16 3 /4-16 STYLE 760F Sleeve 84 760F02 1 /8 760F03 3 /16 760F04 1 /4 760F05 5 /16 760F06 3 /8 760F08 1 /2 760F10 5 /8 760F12 3 /4 760F16 1
Hi-Seal Fittings Material: rass Part Tube Style No. O.D. T1 D E F G STYLE 761F Nut STYLE 762F Union Tube to Tube 761F02 1 /8 3 /8-24 0.516 0.500 761F03 3 /16 7 /16-20 0.531 0.563 761F04 1 /4 1 /2-20 0.594 0.625 761F05 5 /16 9 /16-18 0.672 0.688 761F06 3 /8 5 /8-18 0.750 0.750 761F08 1 /2 3 /4-16 0.891 0.875 761F10 5 /8 15 /16-16 1.000 1.125 761F12 3 /4 1 1 /16-16 1.000 1.250 761F16 1 1 5 /16-16 1.000 1.500 762F02 1 /8 1.344 0.375 0.797 762F03 3 /16 1.406 0.438 0.797 762F04 1 /4 1.563 0.500 0.953 762F05 5 /16 1.781 0.563 0.953 762F06 3 /8 1.875 0.625 1.063 762F08 1 /2 2.188 0.750 1.156 762F10 5 /8 2.500 0.938 1.313 762F12 3 /4 2.500 1.063 1.313 762F14 7 /8 2.563 1.188 1.375 Part Tube Pipe Style No. O.D. Thread D E F G STYLE 763F Male onnector heck Valve Tube to Male Pipe Thread 763F04x02 1 /4 1 /8 1.281 0.500 0.953 763F06x04 3 /8 1 /2 1.641 0.625 1.203 STYLE 764F Union Tee Tube to Tube to Tube cross Flats 764F02 1 /8 1.781 0.891 0.594 0.313 764F03 3 /16 1.969 0.984 0.656 0.375 764F04 1 /4 2.094 1.047 0.719 0.437 764F05 5 /16 2.375 1.188 0.781 0.500 764F06 3 /8 2.469 1.234 0.797 0.500 764F08 1 /2 2.969 1.484 0.938 0.625 764F10 5 /8 3.875 1.938 1.313 1.000 764F12 3 /4 4.125 2.063 1.438 1.000 STYLE 765F Union Elbow Tube to Tube cross Flats 765F02 1 /8 1.109 0.953 0.656 0.156 0.375 765F04 1 /4 1.266 1.047 0.719 0.219 0.437 765F05 5 /16 1.438 1.188 0.781 0.250 0.500 765F06 3 /8 1.516 1.266 0.828 0.250 0.500 765F08 1 /2 1.797 1.484 0.938 0.313 0.625 765F10 5 /8 2.438 1.938 1.313 0.500 1.000 765F12 3 /4 2.563 2.063 1.438 0.500 1.000 765F14 7 /8 2.594 1.938 1.313 0.656 1.313 765F16 1 2.594 1.938 1.313 0.656 1.313 85
Hi-Seal Fittings Material: rass Part Tube Pipe Style No. O.D. Thread D E F G STYLE 766F Female onnector Tube to Female Pipe Thread 766F02X02 1 /8 1 /8 1.141 0.563 0.844 766F04X02 1 /4 1 /8 1.281 0.563 0.953 766F04X04 1 /4 1 /4 1.391 0.750 1.063 766F04X08 1 /4 1 /2 1.828 1.063 1.500 766F06X02 3 /8 1 /8 1.438 0.625 1.000 766F06X04 3 /8 1 /4 1.609 0.750 1.172 766F06X06 3 /8 3 /8 1.672 0.875 1.234 766F06X08 3 /8 1 /2 1.938 1.063 1.500 766F08X04 1 /2 1 /4 1.766 0.750 1.219 766F08X06 1 /2 3 /8 1.828 0.875 1.281 766F08X08 1 /2 1 /2 2.109 1.063 1.563 766F10X08 5 /8 1 /2 2.188 1.063 1.563 766F12X08 3 /4 1 /2 2.188 1.063 1.563 766F12X12 3 /4 3 /4 2.281 1.250 1.656 STYLE 767F Female Run Tee Tube to Female Pipe Thread to Tube Swing cross Radius Flats (SR) 767F04X02 1 /4 1 /8 1.797 1.109 0.781 0.688 0.500 0.859 767F04X04 1 /4 1 /4 2.109 1.219 0.891 0.891 0.688 0.953 767F06X04 3 /8 1 /4 2.391 1.516 1.078 0.875 0.750 1.172 STYLE 768F Male onnector Tube to Male Pipe Thread 86 768F02X02 1 /8 1 /8 1.141 0.437 0.844 768F03X02 3 /16 1 /8 1.172 0.437 0.844 768F04X02 1 /4 1 /8 1.281 0.500 0.953 768F04X04 1 /4 1 /4 1.484 0.625 1.156 768F04X06 1 /4 3 /8 1.453 0.750 1.125 768F04X08 1 /4 1 /2 1.828 0.875 1.500 768F05X02 5 /16 1 /8 1.359 0.563 0.953 768F05X04 5 /16 1 /4 1.563 0.625 1.156 768F05X06 5 /16 3 /8 1.563 0.750 1.156 768F06X02 3 /8 1 /8 1.438 0.625 1.000 768F06X04 3 /8 1 /4 1.641 0.625 1.203 768F06X06 3 /8 3 /8 1.641 0.750 1.203 768F06X08 3 /8 1 /2 1.969 0.875 1.531 768F08X04 1 /2 1 /4 1.797 0.750 1.250 768F08X06 1 /2 3 /8 1.797 0.750 1.250 768F08X08 1 /2 1 /2 2.141 0.875 1.594 768F08X12 1 /2 3 /4 2.109 1.125 1.563 768F10X06 5 /8 3 /8 1.969 0.938 1.344 768F10X08 5 /8 1 /2 2.250 0.938 1.625 768F12X08 3 /4 1 /2 2.250 1.125 1.625 768F12X12 3 /4 3 /4 2.250 1.125 1.625 768F14X12 7 /8 3 /4 2.250 1.250 1.625 768F16X12 1 3 /4 2.250 1.375 1.625 768F16X16 1 1 2.438 1.375 1.813
Hi-Seal Fittings Material: rass Part Tube Pipe Style No. O.D. Thread D E F G STYLE 769F Elbow Tube to Male Pipe Thread Swing cross Radius Flats (SR) 769F02X02 1 /8 1 /8 1.109 0.922 0.625 0.719 0.188 0.375 0.656 769F03X02 3 /16 1 /8 1.141 0.953 0.625 0.719 0.188 0.437 0.688 769F04X02 1 /4 1 /8 1.234 1.016 0.672 0.781 0.219 0.437 0.406 769F04X04 1 /4 1 /4 1.297 1.078 0.750 1.094 0.219 0.437 0.828 769F04X06 1 /4 3 /8 1.453 1.172 0.844 1.000 0.281 0.563 0.875 769F04X08 1 /4 1 /2 1.578 1.234 0.906 1.250 0.344 0.688 0.938 769F05X02 5 /16 1 /8 1.375 1.125 0.719 0.844 0.250 0.500 0.828 769F05X04 5 /16 1 /4 1.406 1.156 0.750 0.938 0.250 0.500 0.844 769F06X02 3 /8 1 /8 1.422 1.172 0.734 0.813 0.250 0.563 0.844 769F06X04 3 /8 1 /4 1.484 1.234 0.797 1.063 0.250 0.500 0.906 769F06X06 3 /8 3 /8 1.578 1.297 0.859 1.063 0.281 0.563 0.969 769F06X08 3 /8 1 /2 1.734 1.391 0.953 1.250 0.344 0.688 1.000 769F08X04 1 /2 1 /4 1.766 1.453 0.906 1.125 0.313 0.625 1.031 769F08X06 1 /2 3 /8 1.766 1.453 0.906 1.125 0.313 0.625 1.031 769F08X08 1 /2 1 /2 1.828 1.484 0.938 1.313 0.344 0.688 1.063 769F10X08 5 /8 1 /2 2.094 1.656 1.031 1.500 0.438 0.875 1.188 769F12X08 3 /4 1 /2 2.219 1.750 1.125 1.500 0.469 0.938 1.328 769F12X12 3 /4 3 /4 2.219 1.750 1.125 1.469 0.469 0.938 1.328 769F16X16 1 1 2.594 1.938 1.313 1.969 0.656 1.313 1.516 STYLE 770F Elbow Tube to Female Pipe Thread Swing cross Radius Flats (SR) 770F02X02 1 /8 1 /8 1.141 0.984 0.688 0.688 0.156 0.375 0.766 770F04X02 1 /4 1 /8 1.266 1.047 0.719 0.688 0.218 0.437 0.797 770F04X04 1 /4 1 /4 1.391 1.141 0.813 0.875 0.250 0.500 0.906 770F06X04 3 /8 1 /4 1.547 1.297 0.859 0.688 0.250 0.500 0.969 770F06X06 3 /8 3 /8 1.719 1.406 1.969 0.938 0.313 0.625 1.078 770F08X04 1 /2 1 /4 1.891 1.578 1.031 0.938 0.313 0.625 1.125 770F08X06 1 /2 3 /8 1.891 1.578 1.031 0.938 0.313 0.625 1.125 770F08X08 1 /2 1 /2 2.000 1.672 1.125 1.188 0.328 0.688 1.250 770F12X12 3 /4 3 /4 2.719 2.063 1.438 1.344 0.656 1.313 1.578 87
Hi-Seal Fittings Material: rass Part Tube Pipe Style No. O.D. Thread D E G STYLE 771F Male Run Tee Tube to Male Pipe Thread to Tube Swing cross Radius Flats (SR) 771F04X02 1 /4 1 /8 1.859 0.781 0.750 1.078 0.437 0.828 771F04X04 1 /4 1 /4 2.047 0.938 0.781 1.109 0.500 0.859 771F06X04 3 /8 1 /4 2.484 1.063 0.984 1.422 0.625 1.078 771F08X06 1 /2 3 /8 2.859 1.188 1.125 1.672 0.750 1.234 771F08X08 1 /2 1 /2 3.141 1.375 1.219 1.766 0.875 1.750 STYLE 772F Male ranch Tee Tube to Tube to Male Pipe Thread Swing cross Radius Flats (SR) 772F04X02 1 /4 1 /8 2.094 1.047 0.781 0.750 0.437 0.813 772F04X04 1 /4 1 /4 2.156 1.078 0.750 0.938 0.437 0.828 772F05X02 5 /16 1 /8 2.375 1.188 0.781 0.813 0.500 0.891 772F06X04 3 /8 1 /4 2.531 1.266 0.828 1.000 0.500 0.938 772F08X06 1 /2 3 /8 2.656 1.484 0.938 1.063 0.625 1.063 772F08X08 1 /2 1 /2 3.406 1.703 1.156 1.344 0.813 1.219 88
Hi-Seal Fittings Material: rass Part Tube Pipe Style No. O.D. Thread D E F STYLE 773F Male Elbow heck Tube to Male Pipe Thread Swing cross Radius Flats (SR) 773F04X02 1 /4 1 /8 1.234 1.016 0.688 0.750 0.219 0.500 0.766 STYLE 777F Female ranch Tee Tube to Tube to Female Pipe Thread Swing cross Radius Flats (SR) 777F04X02 1 /4 1 /8 2.219 1.109 0.781 0.688 0.500 0.859 777F04X04 1 /4 1 /4 2.469 1.234 0.906 1.219 0.688 0.938 777F06X04 3 /8 1 /4 3.031 1.516 1.078 0.875 0.750 1.172 777F12X12 3 /4 3 /4 4.250 2.125 1.500 1.375 1.250 1.641 89
Hi-Seal Fittings Material: rass Part Tube Pipe Style No. O.D. Thread D E F G STYLE 780F Thermocouple onnector 780F04X02 1 /4 1 /8 1.281 0.500 0.953 780F04X04 1 /4 1 /4 1.484 0.625 1.156 Part Tube ulkhead Style No. O.D. Thread D E F G STYLE 782F ulkhead Union Tube to Tube Max. ulkhead 782F02 1 /8 3 /8-24 1.938 9/16 1.344 0.375 782F04 1 /4 1 /2-20 2.219 11/16 1.563 0.375 782F05 5 /16 9 /16-18 2.406 0.750 1.594 0.375 782F06 3 /8 5 /8-18 2.531 13/16 1.656 0.375 782F08 1 /2 3 /4-16 2.844 15/16 1.750 0.375 782F10 5 /8 15 /16-16 3.313 1.125 2.063 0.625 782F12 3 /4 1 1 /16-16 3.438 1.250 2.188 0.625 90
Pipe Fittings Material: rass Min. Wrench Part Orifice Pad/Hex Style No. T1 T2 Size STYLE 100 Elbow 10002 1 /8.328.546 10004 1 /4.422.781 10006 3 /8.562.812 10008 1 /2.687 1.015 STYLE 101 Tee 10102 1 /8.328.546 10104 1 /4.422.719 10106 3 /8.562.840 10108 1 /2.687 1.230 STYLE 102 ross 10202 1 /8.328.546 10204 1 /4.421.781 10206 3 /8.562.840 10208 1 /2.687 1.090 STYLE 103 oupling 10302 1 /8.328.750.562 10304 1 /4.422 1.120.750 10306 3 /8.562 1.125.875 10308 1 /2.687 1.500 1.062 91
Pipe Fittings Material: rass Min. Wrench Part Orifice Pad/Hex Style No. T1 T2 Size STYLE 104 Union 10402 1 /8.328 1.312.562.875 10404 1 /4.437 1.468.687 1.062 10406 3 /8.562 1.625.875 1.312 10408 1 /2.687 1.890 1.062 1.562 STYLE 108 ap 10802 1 /8.500.563 10804 1 /4.750.750 10806 3 /8.875.875 10808 1 /2 1.063 1.063 STYLE 109 Plug 10902 1 /8.609.304.281 10904 1 /4.813.500.375 10906 3 /8.844.500.437 10908 1 /2 1.078.678.563 92
Pipe Fittings Material: rass Min. Wrench Part Orifice Pad/Hex Style No. T1 T2 Size STYLE 110 ushing 11004X02 1 /4 1 /8 0.312 0.750 0.562 11006X02 3 /8 1 /8 0.328 0.750 0.688 11006X04 3 /8 1 /4 0.422 0.750 0.750 11008X02 1 /2 1 /8 0.328 1.000 0.875 11008X04 1 /2 1 /4 0.422 1.000 0.875 11008X06 1 /2 3 /8 0.562 1.000 0.875 11012X06 3 /4 3 /8 0.562 1.000 1.125 11012X08 3 /4 1 /2 0.687 1.000 1.125 STYLE 111 Lock Nut 11102 1 /8 0.187 0.625 11104 1 /4 0.250 0.687 11106 3 /8 0.250 0.937 11108 1 /2 0.250 1.125 T1 STYLE 112 Short Nipple 11202 1 /8 0.265 0.750 *11204 1 /4 0.358 1.125 *11206 3 /8 0.422 1.125 *11208 1 /2 0.531 1.500 *Longer than ST or standard length 93
Pipe Fittings Material: rass Min. Wrench Part Orifice Pad/Hex Style No. T1 T2 Size STYLE 113 Long Nipple 11302X24 1 /8 0.265 1.500 11304X24 1 /4 0.358 1.500 11306X24 3 /8 0.500 1.500 11308X24 1 /2 0.625 1.500 11302X32 1 /8 0.265 2.000 11304X32 1 /4 0.375 2.000 11306X32 3 /8 0.500 2.000 11308X32 1 /2 0.625 2.000 11302X40 1 /8 0.281 2.500 11304X40 1 /4 0.375 2.500 11306X40 3 /8 0.500 2.500 11308X40 1 /2 0.625 2.500 11302X48 1 /8 0.281 3.000 11304X48 1 /4 0.375 3.000 11306X48 3 /8 0.500 3.000 11308X48 1 /2 0.625 3.000 11302X56 1 /8 0.281 3.500 11304X56 1 /4 0.375 3.500 11306X56 3 /8 0.500 3.500 11308X56 1 /2 0.625 3.500 STYLE 116 Street Elbow 11602 1 /8 0.187 0.546 0.812 11604 1 /4 0.312 0.718 1.031 11606 3 /8 0.437 0.781 1.187 11608 1 /2 0.562 1.171 1.437 STYLE 117 Plug (Slotted Heads) 11702 1 /8 0.312 11704 1 /4 0.469 11706 3 /8 0.469 STYLE 119 Reducing ushing Female to Female 11904X02 1 /4 1 /8 0.970 0.750 11906X04 3 /8 1 /4 1.160 0.875 11908X06 1 /2 3 /8 1.375 1.062 94
Pipe Fittings Material: rass Min. Wrench Part Orifice Pad/Hex Style No. T1 T2 Size STYLE 120 dapter 12002X02 1 /8 1 /8 0.191 0.906 0.531 0.500 12004X02 1 /4 1 /8 0.219 1.063 0.688 0.750 12004X04 1 /4 1 /4 0.312 1.250 0.688 0.750 12006X04 3 /8 1 /4 0.312 1.250 0.688 0.875 12008X06 1 /2 3 /8 0.406 1.469 0.906 1.062 STYLE 121 Plug 12102 1 /8 0.531 0.437 12104 1 /4 0.750 0.562 12106 3 /8 0.781 0.562 12108 1 /2 0.969 0.750 12112 3 /4 1.062 0.750 STYLE 122 Hex Nipple 12202 1 /8 0.187 0.906 0.375 0.437 12204 1 /4 0.312 1.375 0.562 0.562 12206 3 /8 0.437 1.406 0.562 0.687 12208 1 /2 0.562 1.812 0.750 0.875 STYLE 123 Reducing Nipple 12304X02 1 /4 1 /8 0.218 1.190 0.562 12306X04 3 /8 1 /4 0.313 1.406 0.687 STYLE 124 45 Street Elbow 12402 1 /8 0.218 0.750 0.687 12404 1 /4 0.312 0.875 0.781 12406 3 /8 0.406 1.000 0.875 12408 1 /2 0.500 1.125 1.218 95
Pipe Fittings Material: rass Min. Wrench Part Orifice Pad/Hex Style No. T1 T2 Size STYLE 126 Elbow 12602 1 /8 0.125 0.484 0.781 STYLE 127 Male Run Tee 12702 1 /8 0.187 0.750 0.750 12704 1 /4 0.312 0.781 1.156 12706 3 /8 0.406 0.875 1.188 STYLE 128 Reducing Street Elbow 12804X02 1 /4 1 /8 0.218 0.875 0.843 0.500 STYLE 129 ulkhead dapter ulkhead Thread 12902X24 1 /8 5 /8-18 0.328 1.500 0.875 12904X15 1 /4 3 /4-16 0.421 0.938 1.000 12904X24 1 /4 3 /4-16 0.421 1.250 1.000 12906X21 3 /8 1-14 0.562 1.313 1.125 12908X24 1 /2 1 1 /8-14 0.687 1.500 1.250 STYLE 130 lamping Stud Male NPTF to Male NPTF and Female NPTF ulkhead Thread 13008X04X35 1 /2 1 /4 3 /4-16 2.156 1.125 1.250 13008X04X41 1 /2 1 /4 3 /4-16 2.531 1.125 1.250 96
Reference Data Decimal and Metric Equivalent of Fractions Decimal Metric Decimal Metric 1 16 1 8 3 16 1 4 5 16 3 8 7 16 1 2 1 32 3 32 5 32 7 32 9 32 11 32 13 32 15 32 1 64 3 64 5 64 7 64 9 64 11 64 13 64 15 64 17 64 19 64 21 64 23 64 25 64 27 64 29 64 31 64.0156 0.397.0313 0.794.0469 1.191.0625 1.588.0781 1.984.0938 2.381.1094 2.778.1250 3.175.1406 3.572.1562 3.969.1719 4.366.1875 4.762.2031 5.159.2188 5.556.2344 5.953.2500 6.350.2656 6.747.2812 7.144.2969 7.541.3125 7.938.3281 8.334.3438 8.731.3594 9.128.3750 9.525.3906 9.922.4062 10.319.4219 10.716.4375 11.112.4531 11.509.4688 11.906.4844 12.303.5000 12.700 9 16 5 8 11 16 3 4 13 16 7 8 15 16 1 17 32 19 32 21 32 23 32 25 32 27 32 29 32 31 32 33 64 35 64 37 64 39 64 41 64 43 64 45 64 47 64 49 64 51 64 53 64 55 64 57 64 59 64 61 64 63 64.5156 13.097.5313 13.494.5469 13.891.5625 14.288.5781 14.684.5938 15.081.6094 15.478.6250 15.875.6406 16.272.6562 16.669.6719 17.066.6875 17.462.7031 17.859.7188 18.256.7344 18.653.7500 19.050.7656 19.447.7812 19.844.7969 20.241.8125 20.638.8281 21.034.8438 21.431.8594 21.828.8750 22.225.8906 22.822.9062 23.019.9219 23.416.9375 23.812.9531 24.209.9688 24.606.9844 25.003 1.0000 25.400 97
Thermoplastic Tubing urst vs. Temperature Data IMPOLENE TUING 1000 urst Versus Temperature -IMPOLENE PY ND PP LK MINIMUM URST PRESSURE. PSI 900 800 700 600 500 400 300 200 22,33,44,55,66, PY & PPK 88PY & 88PPK 100 0 70 150 200 TEMPERTURE ( F), SUGGESTED WORKING PRESSURE IS 1/4 OF URST PRESSURE T THE SYSTEM OPERTING TEMPERTURE 3000 urst Versus Temperature -NYLO SEL NT, NH, SNK, NSRK, ND NF TUING NH & NSRK (EXEPT 88 SIZE) 2500 MINIMUM URST PRESSURE. PSI 2000 1500 1000 88NH & 88NSRK NT & SNK - LL SIZES NF - LL SIZES 500 0 70 150 200 TEMPERTURE ( F), SUGGESTED WORKING PRESSURE IS 1/4 OF URST PRESSURE T THE SYSTEM OPERTING TEMPERTURE 98
Thermoplastic Tubing urst vs. Temperature Data POLY-FLO TUING 450 urst Versus Temperature - POLY -FLO P, PE, PF TUING 400 MINIMUM URST PRESSURE. PSI 350 300 250 200 150 100 44 P, PE, PF 66 P, PE, PF 88 P, PE, PF 50 0 70 150 175 TEMPERTURE ( F), SUGGESTED WORKING PRESSURE IS 1/4 OF URST PRESSURE T THE SYSTEM OPERTING TEMPERTURE PV LER TUING 250 urst Versus Temperature - PV TUING 44PVLR MINIMUM URST PRESSURE. PSI 200 150 100 50 66PVLR 88PVLR 0 70 105 135 165 TEMPERTURE ( F), SUGGESTED WORKING PRESSURE IS 1/4 OF URST PRESSURE T THE SYSTEM OPERTING TEMPERTURE 99
Thermoplastic Tubing Poly-Flo, PE (NSF pproved) Linear Low Density Polyethylene Tubing urst Working Weight Tube Wall Pressure Pressure Min. end (pprox.) Part Tube O.D. Thickness at 73 F at 73 F Radius Per Ft. No. (Inches) (Inches) (PSI) (PSI) (Inches) (Lbs.) 22PE 1/8 0.020 500 125 1/2 0.29 532PE 5/32 0.025 500 125 5/8 0.44 33PE 3/16 0.030 500 125 3/4 0.65 44PE 1/4 0.040 400 100 1 1.10 66PE 3/8 0.062 350 87 1 1/4 2.50 88PE 1/2 0.062 250 62 2 1/2 3.40 Impolene Poly-Flo, P lack (Non-NSF pproved) Linear Low Density Polyethylene Tubing 22P 1/8 0.020 500 125 1/2 0.29 532P 5/32 0.025 500 125 5/8 0.44 33P 3/16 0.030 500 125 3/4 0.65 44P 1/4 0.040 400 100 1 1.10 55P 5/16 0.062 600 150 1 1/8 1.90 66P 3/8 0.062 350 87 1 1/4 2.50 88P 1/2 0.062 250 62 2 1/2 3.40 POLY-FLO Poly-Flo, PF lack (Non-NSF pproved) Flame Retardent Tubing 44PF 1/4 0.040 400 100 1 1.10 66PF 3/8 0.062 350 87 1 1/4 2.50 88PF 1/2 0.062 250 62 2 1/2 3.40 Linear Low Density Polyethylene Tubing POLY-FLO Impolene, PY (NSF pproved) Polyallomer Tubing 22PY 1/8 0.023 900 225 1/2 0.28 33PY 3/16 0.034 900 225 3/4 0.63 44PY 1/4 0.040 900 225 1 1.10 66PY 3/8 0.062 900 225 1 1/4 2.40 88PY 1/2 0.062 750 187 2 1/2 3.30 Impolene Impolene, PP lack (Non-NSF pproved) Polyallomar Tubing lack 22PP 1/8 0.023 900 225 1/2 0.28 33PP 3/16 0.034 900 225 3/4 0.63 44PP 1/4 0.040 900 225 1 1.10 66PP 3/8 0.062 900 225 1 1/4 2.40 88PP 1/2 0.062 750 187 2 1/2 3.30 Impolene 100
Thermoplastic Tubing PPLITIONS PERFORMNE DT Usual Service Part olors and No. vailable Temperature Range onstruction/onformances 22PE Natural For pneumatic lines, instrumentation Resists most solvents and Natural: STM D-1248, 532PE Natural systems, water piping and limited chemicals. Withstands more than Type 1, lass, 33PE Natural food service. 500 hours in Igepal solution. ategory 3 44PE Natural, lue, Red, Federal Spec: LP390, Green, Orange, Temperature Range: Type 1, lass L, Grade 2, Purple, Gray, Yellow 80 F to +175 F ategory 3 66PE Natural, lue, Red olors: STM D-124, Green, Orange, Type 1, lass, Purple, Gray, Yellow ategory 3 88PE Natural Federal Spec: LP 370, Type 1, lass L, Grade 2, ategory 3 Flexible Tubing 22P lack For pneumatic lines, instrumentation Resists most solvents and STM D-1248, Type 1, 532P lack systems and water piping. chemicals. Withstands more lass, ategory 4 33P lack than 500 hours in Igepal solution. Federal Spec: LP-390, 44P lack Temperature Range: Type 3, lass L, Grade 2, 55P lack 80 F to +175 F ategory 4 66P lack Flexible Tubing lack Tubing offers outstanding resistance to sunlight 88P lack 44PF lack For heating control systems in Highest resistance to Flammability characteristic: 66PF lack commercial building, chemical environmental stress cracking Maximum allowable 88PF lack conduit, data control equipment of all regular polyethylene resins. burning rate for systems. Ideal in gas and liquid Withstands more than 500 hours PF tubing=3.9 cm/min per conducting applications. in Igepal solution. STM D635 Flexible Tubing Temperature Range: 80 F to +175 F 22PY White For instrumentation, pneumatic and Excellent corrosion resistances. an be repeatedly steam 33PY White lubricant lines, hydraulic lines, It can be used with greater range stabilized. 44PY White process lines forgases, chemicals, of liquids and gases than nylon Not subject to environmental 66PY White and solvents. Ideal for use at or polyethylene. Good acid and stress cracking. 88PY White higher temps. Limited food service. chemical resistance. Flexible Tubing Temperature Range: 20 F to +212 F 22PP lack For instrumentation, pneumatic and Excellent corrosion resistances. an be repeatedly steam 33PP lack lubricant lines, process lines for It can be used with greater range stabilized. 44PP lack gases, chemicals and solvents. of liquids and gases than nylon Not subject to environmental 66PP lack Ideal for use at higher temps. or polyethylene. Withstands stress cracking. 88PP lack boiling sulfuric acid, concentrated lack tubing offers Temperature Range: hydrochloric acid up to the boiling outstanding resistance to 20 F to +212 F point and saline solution up to sunlight. 200 F. Flexible Tubing 101
Thermoplastic Tubing Nylo-Seal, NH & NT (NSF pproved) Nylon 11 Tubing urst Working Weight Tube Wall Pressure Pressure Min. end (pprox.) Part Tube O.D. Thickness at 73 F at 73 F Radius Per Ft. No. (Inches) (Inches) (PSI) (PSI) (Inches) (Lbs.) 22NT 1/8 0.017 1,500 375 1/2 0.26 532NT 5/32 0.022 1,500 375 5/8 0.44 33NT 3/16 0.024 1,500 375 3/4 0.60 44NT 1/4 0.033 1,500 375 1 1.00 55NT 5/16 0.040 1,500 375 1 1/2 1.50 66NT 3/8 0.048 1,500 375 1 3/4 2.20 88NT 1/2 0.062 1,500 375 2 3/8 3.20 22NH 1/8 0.026 2,500 625 3/8 0.37 33NH 3/16 0.039 2,500 625 5/8 0.81 44NH 1/4 0.050 2,500 625 7/8 1.40 66NH 3/8 0.075 2,500 625 1 1/2 3.19 88NH 1/2 0.075 2,500 625 2 1/2 4.50 Nylo-Seal, SN & NSR (Non-NSF pproved) lack Nylon 11 Tubing NYLO-SEL 22SN 1/8 0.017 1,500 375 1/2 0.26 532SN 5/32 0.022 1,500 375 5/8 0.44 33SN 3/16 0.024 1,500 375 3/4 0.60 44SN 1/4 0.033 1,500 375 1 1.00 55SN 5/16 0.040 1,500 375 1 1/2 1.50 66SN 3/8 0.048 1,500 375 1 3/4 2.20 88SN 1/2 0.062 1,500 375 2 3/8 3.20 22NSR 1/8 0.026 2,500 625 3/8 0.37 33NSR 3/16 0.039 2,500 625 5/8 0.81 44NSR 1/4 0.050 2,500 625 7/8 1.40 66NSR 3/8 0.075 2,500 625 1 1/2 3.19 88NSR 1/2 0.075 2,500 625 2 1/2 4.50 Nylo-Seal, NF (Non-NSF pproved)plasticized Tubing Nylon 11 Tubing NYLO-SEL 22NF 1/8 0.023 1,000 250 3/8 0.33 532NF 5/32 0.024 1,000 250 5/8 0.45 33NF 3/16 0.024 1,000 250 5/8 0.54 44NF 1/4 0.033 1,000 250 7/8 1.02 55NF 5/16 0.040 1,000 250 1 1/4 1.56 66NF 3/8 0.048 1,000 250 1 1/2 2.24 88NF 1/2 0.062 1,000 250 2 3.89 440NF 1/4 0.040 1,000 250 1/2 1.20 660NF 3/8 0.060 1,000 250 3/4 2.78 Polyvinyl hloride (Non-NSF pproved) PV Tubing 44PV 1/4 0.040 200 50 1/2 1.13 66PV 3/8 0.062 160 40 1 3.20 88PV 1/2 0.062 140 35 2 4.50 Style 6 ir rake Tubing SE J844 DOT FMVSS 106 HYTRON IR RKE TUIN 602 1/8 0.023 1,000 150 3/8 0.26 603 3/16 0.035 1200 150 1 0.78 604 1/4 0.040 1000 150 1 1.20 605 5/16 0.040 1000 150 1 1/4 1.50 606 3/8 0.063 1400 150 1 1/2 2.80 608 1/2 0.063 950 150 2 4.30 610 5/8 0.092 900 150 2 1/2 6.80 612 3/4 0.092 800 150 3 8.50 102
22NT Natural For instrumentation lines, lubrication Resists vermin attack. Moisture not required for 532NT Natural and process piping systems, fuel, flexibility. 33NT Natural oil and refrigerant lines. 44NT Natural Flexible Tubing 55NT Natural Temperature Range: 66NT Natural 60 F to +212 F 88NT Natural 22NH 33NH 44NH 66NH 88NH Natural Natural Natural Natural Natural Thermoplastic Tubing PPLITIONS PERFORMNE DT Usual Service Part olors and No. vailable Temperature Range onstruction/onformances 22SN lack For instrumentation lines, lubrication Resists vermin attack. Moisture not required for 532SN lack and process piping systems, fuel, flexibility. 33SN lack oil and refrigerant lines. lack tubing offers 44SN lack Limited food service. outstanding resistance to 55SN lack sunlight. 66SN lack Temperature Range: 88SN lack 60 F to +225 F Flexible Tubing 22NSR 33NSR 44NSR 66NSR 88NSR lack lack lack lack lack 22NF lack, Natural For instrumentation lines, lubrication Resists vermin attack. Moisture not required for 532NF lack, Natural and process piping systems, fuel, flexibility. 33NF lack, Natural oil and refrigerant lines. lack tubing offers 44NF lack, Natural outstanding resistance to 55NF lack, Natural Temperature Range: sunlight. 66NF lack, Natural 60 F to +225 F 88NF lack, Natural Flexible Tubing 440NF lack, Natural 660NF lack, Natural 44PV lear For pneumatic lines and water Flexible Tubing 66PV lear piping. lear tubing is ideal where 88PV lear visual inspection of flow and cleanliness is desired. Temperature Range: 20 F to +165 F 602 lack For replacing metal air brake Material Specifications: onformances: 603 lack tubing on air brake systems, Tube: Nylon DOT FMVSS 106 604 lack, lue, Red, except for the compressor Reinforcement: Polyester Fiber SE J844 Yellow, Green, discharge lines and other over: Nylon. Totally onded rown, Orange temperature limiting locations. 605 lack 606 lack, rown, lue, Green, Temperature Range: Orange, Red, -40 F to +200 F Yellow 608 lack, lue, Red, Green, rown, Yellow 610 lack, lue, Red, Green, 612 lack 103
Reference Data How to Install Metal Tubing PREUTIONS void straight line connections wherever possible, especially in short runs. Design piping systems symmetrically. They are easier to install and present a neat appearance. are should be taken to eliminate stress from tubing lines. Long tubing runs should be supported by brackets or clips. ll parts installed on tubing lines such as heavy fittings, valves, etc., should be bolted down to eliminate tubing fatigue. efore installing tubing, inspect the tube to see that it conforms to the required specifications, is of the correct diameter and wall thickness and is not out of round. ut tube ends reasonably square and light deburr inside and outside edge. hamfer on outside edge will destroy bearing of tube end on the fitting seat. To avoid difficulty in assembly and disconnecting, a sufficient straight length of tube must be allowed from the end of the tube to the start of the bend. llow twice the length of the nut as a minimum. Tubes should be formed to assemble with true alignment to the center line of the fittings, without distortion or tension. Recommended Metal Tubing Flare Dimensions SE 37 FLRE TUES Maximum Diameter Wall Thickness Tube (Inches) R (Inches) O.D. Radius Single Double Size Single Flare Double Flare (Inches) Flare Flare (Inches) Max. Min. Max. Min. ±020 D D 1 1/8.200.180.200.180.030.035.025 3/16.280.260.280.260.030.035.028 1/4.360.340.360.340.030.065.035 5/16.430.400.430.400.030.065.035 3/8.490.460.490.460.040.065.049 1/2.660.630.660.630.060.083.049 5/8.790.760.790.760.060.095.049 3/4.950.920.950.920.080.109.049 7/8 1.070 1.040 1.070 1.040.080.109.065 1 1.200 1.170 1.200 1.170.090.120.065 SE 45 FLRE TUES Double Maximum Flare Wall Thickness Tube Diameter oined (Inches) O.D. (Inches) Seat Single Double Size Flare Flare (Inches) Single Flare Double Flare (Inches) D D 1 1/8.171/.181.198/.213.040.035.025 3/16.239/.249.265/.280.040.035.028 1/4.315/.325.345/.360.040.049.035 5/16.388/.404.410/.425.062.049.035 3/8.471/.487.485/.500.062.065.049 7/16.545/.561.555/.570.062.065.049 1/2.607/.623.625/.640.062.083.049 9/16.660/.676.697/.712.062.083.049 5/8.732/.748.757/.772.062.095.049 3/4.900/.916.897/.912.062.109.049 7/8 1.025/1.041.109 1 1.141/1.157.120 104
General Information Thermoplastic hemical Resistance hart The information given below is based on reliable test results. are should be taken to use this data as a guide only, and to take into account such variables as temperature, concentration and fluid contamination. Each application should be tested prior to its use in commercial systems. ll ratings are given at 73 F. ontact Imperial Eastman for high temperature applications. Key to Ratings: = Excellent. Little or no swelling or softening. = Good. Swelling or softening is moderate. = Fair. onditional service may be expected. D = Unsatisfactory. Not recommended. NT = Not tested. Poly-Flo Impolene Nylo-Seal PV Poly-Flo Impolene Nylo-Seal PV cetaldehyde D D cetate solvents-crude D cetate solvents-pure D cetic cid 20% cetic cid 50% cetic cid-pure D D cetone D D cetophenone NT D cetylene D ir lcohols luminum hloride D luminum Sulfate lums mmonia (queous, liquid and cold gas) mmonium cetate mmonium arbonate mmonium hloride D mmonium Hydroxide mmonium Nitrate mmonium Phosphate mmonium Sulfate myl cetate D myl lcohol myl hloride D D D niline D sphalt D arium Salts eer eet Sugar Liquors NT enzaldehyde D D enzene or enzol D D enzoic cid orax oric cid randy NT romine Water, saturated D D D D utane D utter utyl cetate D alcium isulfite D alcium Hypochlorite D alcium Salts ane Sugar Liquors arbon Dioxide arbon Dioxide (dry) arbon Dioxide (wet) arbon Tetrachloride D D D arrot hlorine D D D D hloroform D D D hocolate Syrup hromic cid NT itric cid oke Oven Gas opper Salts opper Sulfate ore Oils NT ottonseed Oil reosote D D D yclohexanol D yclohexanone D D D Dibutyl Phthalate D Dichloroethylene NT NT Dioxane D D E Ethers D D D Ethyl cetate D Ethyl lcohol 40% D D Ethylene Glycol F Ferric hloride D Ferric Sulfate Ferrous hloride Ferrous Sulfate Formaldehyde Formic cid D Freon NT NT D Furfural D D D G Gasoline (sour) D D D Gasoline (refined) D D D Gelatin Glucose Glue Glycerin or Glycerol H Hydraulic Fluid D D Hydraulic Fluid (water/glycol) NT Hydrochloric cid 30% D Hydrochloric cid 50% D Hydrocyanic cid D Hydrofluoric cid (dil.) Hydrofluoric cid 38-40% D Hydrofluoric cid 50% D Hydrogen Fluoride D D Hydrogen Hydrogen Peroxide D Hydrogen Sulfide (dry) Hydrogen Sulfide (wet) 105
General Information Thermoplastic hemical Resistance hart Poly-Flo Impolene Nylo-Seal PV Poly-Flo Impolene Nylo-Seal PV I Iodine (in alcohol) D Isopropanol NT K Karo Syrup L Lacquer Solvents D Lactic cid Lead cetate Lime Sulfur NT Linseed Oil D NT M Machine Oil Magnesium hloride Magnesium Hydroxide Magnesium Sulfate Maleic cid NT NT Manganese Salts Mayonnaise Mercuric hloride D Mercury Methanol Methylene hloride D Milk Molasses N Natural Gas Nickel hloride Nickel Salts Nickel Sulfate D Nitric cid (dil.) D Nitric cid (med. conc.) D D Nitric cid (conc.) D D D Nitrobenzene D D Nitrogen Oxides D Nitrous cids NT D O Oils, Vegetable D Oleic cid D D Olive Oil D Oxalic cid Oxygen Gas P Palmitic cid D Perchloric cid D D Petroleum Oils (sour) Pertoleum Oils (refined) Phenol NT NT D D Phosphoric cid 25% Phosphoric cid 25-50% Phosphoric cid 50-85% Picric cid D D D Potassium arbonate Potassium hlorate Potassium hloride Potassium Hydroxide Potassium Iodide Potassium Sulfate Propane D Pyridine D 106 R Rosin (light) D S Sauerkraut Shellac D Silver Nitrate Soap Solutions Sodium icarbonate Sodium isulfate D Sodium isulfite Sodium orate Sodium arbonate Sodium hlorate Sodium hloride Sodium yanide Sodium Hydroxide Sodium Hypochlorite D Sodium Metaphosphate Sodium Nitrate Sodium Perborate Sodium Phosphate Sodium Silicate Sodium Sulfate Sodium Sulfide Sodium Sulfite Sodium Thiosulfate (hypo) Stearic cid Succinic cid Sulfate Liquors D Sulfur Sulfur hloride D Sulfur Dioxide D Sulfuric cid 10% D Sulfuric cid 10-75% D Sulfuric cid 75-98% D D D Sulfurous cid D T Tannic cid Tar D Tartaric cid Tetrahydrofurane D D Tetralin D D NT Thiopen D NT Toluene or Toluol D Tomato Trichlorethylene D D D Turpentine D U Urea V Varnish D Vinegar W Water (fresh) Water (salt) Whiskey Wines X Xylene or Xylol D D Z Zinc hloride Zinc Sulfate D NT
Index lpha-numeric by Part Number atalog No. Page No. 100 91 101 91 102 91 103 91 104 92 108 92 109 92 110 93 111 93 112 93 113 94 116 94 117 94 119 94 120 95 121 95 122 95 123 95 124 95 126 96 127 96 128 96 129 96 130 96 161F 53 209OF 39 256P 23 259P 23 260P 23 260U 24 260U 24 261P 24 261PG 24 261U 25 261U 25 261UG 25 262OF 37 262P 25 262P 26 262PH 26 262PHS 26 264OF 37 264P 26 265OF 37 266OF 37 266P 27 268OF 38 268P 27 269LLP 28 atalog No. Page No. 269OF 38 269OFS 38 269P 27 269SP 28 270P 28 271OFS 39 271P 29 272OFS 39 272P 29 277P 29 279P 30 282OF 39 282P 30 282P 30 282PT 31 292P 31 293P 32 294P 33 294P 33 294PSS 35 294PD 33 294PM 33 294PMD 34 294PMSS 35 294PMSSD 35 294PSS 35 294PSSD 36 296P 32 297P 32 298P 34 298PD 34 298PSS 36 298PSSD 36 298PT 34 298PTSS 36 31PG 23 41F 60 41FS 60 511GS 61 60F 49 60FL 46 60FLV 46 61M 54 61F 49 61FL 46 625F 61 62M 54 62F 49 62FL 46 atalog No. Page No. 639F 61 63M 54 63F 50 63FL 47 640F 61 641F 62 641FS 62 641FSH 62 642F 63 643F 63 644F 63 645F 64 646F 64 648F 64 649F 65 64 60 64M 55 64F 50 64FL 47 650F 65 651F 65 653F 65 654F 66 655F 66 656F 66 657F 66 65M 55 65F 50 660F 66 661F 67 662F 67 662FS 67 664F 67 669F 68 66M 56 66F 50 66FL 47 66L 40 672FS 68 673FS 68 679F 68 68M 56 68F 51 68FL 47 68FLV 47 69M 57 69F 51 69FL 48 69FLV 48 atalog No. Page No. 708F 84 708FS 69 708FSS 75 70M 58 70F 52 711F 84 711FSS 75 71M 58 71F 52 71FL 48 721F 84 721FS 69 721FSS 75 722FSS 75 72M 58 72F 52 72FL 48 72L 40 73M 58 74M 58 752FS 69 752FSS 75 754F 84 754FS 69 754FSS 76 756F 84 756FSS 76 760F 84 760FPH 76 760FS 69 760FSS 76 760FSSZ 83 760FSZ 83 760FT 76 761F 85 761FS 70 761FSS 77 761FSSZ 83 761FSZ 83 762F 85 762FS 70 762FSS 77 763F 85 764F 85 764FS 70 764FSS 77 765F 85 765FS 70 765FSS 77 atalog No. Page No. 766F 86 766FS 71 766FSS 78 767F 86 767FS 71 767FSS 78 768F 86 768FS 71 768FSO 74 768FSS 78 769F 87 769FS 72 769FSO 74 769FSS 79 76M 59 76F 53 770F 87 770FS 72 770FSS 79 771F 88 771FS 72 771FSO 74 771FSS 80 772F 88 772FS 73 772FSO 74 772FSS 80 773F 84 777F 89 777FS 73 777FSS 81 780F 90 780FSS 81 782F 90 782FS 73 782FSS 82 786FSS 82 788FSS 82 792FS 73 80M 59 80F 53 81L 40 82M 59 82L 40 84L 41 85L 41 86L 41 87L 42 88L 42 atalog No. Page No. 89L 43 90L 43 91L 44 92L 44 94L 44 95L 45 99L 45 107
Technical Data Table of Decimal & Metric Equivalents 64ths 32nds 16ths 8ths Decimal MM 1/64 0.01562 0.397 1/32 0.03125 0.794 3/64 0.04688 1.191 1/16 0.06250 1.588 64ths 32nds 16ths 8ths Decimal MM 33/64 0.51562 13.097 17/32 0.53125 13.494 35/64 0.54688 13.891 9/16 0.56250 14.288 5/64 0.07812 1.984 3/32 0.09375 2.381 7/64 0.10938 2.778 1/8 0.12500 3.175 37/64 0.57812 14.684 19/32 0.53975 15.081 39/64 0.60938 14.478 5/8 0.62500 15.875 9/64 0.14062 3.572 5/32 0.15625 3.968 11/64 0.17188 4.366 3/16 0.18750 4.763 41/64 0.64062 16.272 21/32 0.65625 16.669 43/64 0.67188 17.066 11/16 0.68750 17.463 13/64 0.20312 5.159 7/32 0.21875 5.556 15/64 0.23438 5.953 1/4 0.25000 6.350 45/64 0.70312 17.859 23/32 0.71875 18.256 47/64 0.73438 18.653 3/4 0.75000 19.050 17/64 0.26562 6.747 19/32 0.28125 7.144 19/64 0.29688 7.541 5/16 0.32150 7.938 49/64 0.76562 19.447 25/32 0.78125 19.844 5/64 0.79688 20.241 13/16 0.81250 20.638 21/64 0.32812 8.334 11/32 0.34375 8.731 23/64 0.35938 9.128 3/8 0.37500 9.525 53/64 0.82812 21.034 27/32 0.84375 21.431 55/64 0.85938 21.823 7/8 0.87500 22.225 25/64 0.39062 9.922 13/32 0.40625 10.319 27/64 0.41288 10.716 7/16 0.43750 11.113 57/64 0.89062 22.622 29/32 0.90625 23.019 59/64 0.92188 23.416 15/16 0.93750 23.813 29/64 0.45312 11.509 15/32 0.46875 11.906 31/64 0.48438 12.303 1/2 0.50000 12.700 61/64 0.95312 24.209 31/32 0.96875 24.606 63/64 0.98438 25.003 1 1.0000 25.400 108
TO ONVERT INTO MULTIPLY Y TO ONVERT INTO MULTIPLY Y tmospheres cms of mercury 76.0 ubic Feet cubic cms 2.832 x 10 4 atmospheres ft. of water (at 4 ) 33.90 cu ft cu inches 1728 atmospheres in of mercury cu ft cu meters 0.02832 (at 0 ) 29.92 cu ft cu yds 0.03704 atmospheres kgs/sq cm 1.0333 cu ft gals 7.48052 atmospheres kgs/sq meter 10.332 cu ft liters 28.32 atmospheres pound/sq in 14.70 cu ft pints (liq) 59.84 cu ft quarts (liq) 29.92 ar newtons/sq m 10 5 u Ft/min cu cms/sec 472.0 bar atmospheres 0.9869 cu ft/min gals/sec 0.1247 bar at (tech.) 1.0197 cu ft/min liters/sec 0.4720 bar psi 14.504 cu ft/min lbs water/min 62.43 cu ft/sec gals/min 448.831 arrels Oil gals/oil 42 T Units kg calories 0.2520 u Inches cc 16.39 TUs ft lbs 777.9 cu ins cu ft 5.787 x 10-4 TUs hp hrs 3.927 x 10-4 cu ins cu meters 1.639 x 10-5 TUs kgs meters 107.5 cu ins cu yds 2.143 x 10-5 TUs kw hrs 2.928 x 10-4 cu ins gals 4.329 x 10-3 cu ins liters 1.639 x 10-2 TU/Min ft lb/sec 12.96 cu ins pints (liq) 0.03463 TU/min hp 0.02356 cu ins quarts (liq) 0.01732 TU/min kw 0.01757 TU/min watts 17.57 u Meters cc 10 4 cu M cu ft 35.31 entimeters inches 0.3937 cu M cu ins 61,023 cm meters 0.01 cu M cu yds 1.308 cm mm 10 cu M gals 264.2 cu M liters 10 3 ms mercury atm 0.01316 cu M pints (liq) 2113 cms mercury ft water 0.4461 cu M quarts (liq) 1057 cms mercury kgs/sq meter 136.0 cms mercury lbs/sq ft 27.85 u Yards cu cms 7.646 x 10 5 cms mercury lbs/sq in 0.1934 cu yds cu ft 27 cu yds cu ins 46,656 ms/second ft/min 1.969 cu yds cu meters 0.7646 cms/sec ft/sec 0.03281 cu yds gals 202.0 cms/sec km/hr 0.036 cms/sec meter/min 0.6 Decimeters meters 0.1 cms/sec miles/hr 0.02237 cms/sec miles/min 3.728 x 10-4 Degrees (ngle) minutes 60 degs (angle) radians 0.01745 ms/sec/sec ft/sec/sec 0.03281 degs (angle) secs 3600 ubic ms cu ft 3.531 x 10-5 cu cms cu in 6.102 x 10-2 cu cms cu meters 10 6 cu cms cu yds 1.308 x 10-6 cu cms gals 2.642 x 10-4 cu cms liters 10-3 cu cms pints (liq) 2.113 x 10-3 cu cms quarts (liq) 1.057 x 10-3 Technical Data onversion Factors 109
Technical Data onversion Factors TO ONVERT INTO MULTIPLY Y TO ONVERT INTO MULTIPLY Y Degrees/Sec radians/sec 0.01745 Horse-Power TUs/min 42.44 degs/sec revs/min 0.1667 hp ft lbs/min 33,000 degs/sec revs/sec 0.002778 hp ft lbs/sec 550 hp hp (metric) 1.014 Feet cms 30.48 hp kg calories/min 10.70 ft ins 12 hp kws 0.7457 ft meters 0.3048 hp watts 745.7 ft yds 1/3 Hp Hours TUs 2547 Ft of Water atms 0.02950 hp hrs ft lbs 1.98 x 10 6 ft of w ins mercury 0.8826 hp hrs kg calories 641.7 ft of w kgs/sq cm 0.03048 hp hrs kg meters 2.737 x 10 5 ft of w lbs/sq ft 62.32 hp hrs kw hrs 0.7457 ft of w lbs/sq in 0.4328 Inches cms 2.540 Feet/Min cm/sec 0.5080 ft/min ft/sec 0.01667 Ins Mercury atms 0.002458 ft/min kms/hr 0.01829 ins mercury ft water 1.133 ft/min meters/min 0.3048 ins mercury kgs/sq cm 0.03453 ft/min miles/hr 0.01136 ins mercury lbs/sq ft 70.73 ins mercury lbs/sq in 0.4912 Ft/Sec/Sec cms/sec/sec 30.48 ft/sec/sec Meters/sec/sec 0.3048 Ins of Water atms 0.002458 ins of w ins mercury 0.07355 Ft Pounds TUs 1.286 x 10-3 ins of w kgs/sq cm 0.002540 ft lbs hp hrs 5.050 x 10-7 ins of w lbs/sq ft 5.202 ft lbs kg calories 3.241 x 10-4 ins of w lbs/sq in 0.03613 ft lbs kg meters 0.1383 ft lbs kw hrs 3.766 x 10-7 Kilograms dynes 980,665 kgs lbs 2.205 Ft lbs/min TUs/min 7.717 x 10-2 kgs tons (short) 1.102 x 10-3 ft-lbs/min ft-lbs/sec 0.01667 kgs grams 1000 ft lbs/min hp 3.030 x 10-5 ft-lbs/min kg-calories/min 3.241 x 10-3 Kgs/Sq m atms 0.9678 ft-lbs/min kws 2.260 x 10-5 kgs/sq cm ft water 32.81 kgs/sq cm ins mercury 28.96 Ft lbs/sec TUs/min 7.717 x 10-2 kgs/sq cm lbs/sq ft 2048 ft-lbs/sec hp 1.818 x 10-3 kgs/sq cm lbs/sq in 14.22 ft-lbs/sec kg-calories/min 1.945 x 10-2 ft-lbs/sec kws 1.356 x 10-3 Kilometers cms 10 5 kms ft 3281 Gallons ccs 3785 kms meters 10 3 gals cu ft 0.1337 kms miles 0.6214 gals cu ins 231 gals cu meters 3.785 x 10-3 Kms/Hr cms/sec 27.78 gals liters 3.785 kms/hr ft/min 54.68 gals pints (liq) 8 kms/hr ft/sec 0.9113 gals quarts (liq) 4 kms/hr meters/min 16.67 kms/hr miles/hr 0.6214 Gallons, Imp US gals 1.20095 gallons, US imp gals 0.83267 Kms/Hr/Sec cms/sec/sec 27.78 kms/hr/sec ft/sec/sec 0.9113 Gallons/Min cu ft/sec 2.228 x 10-3 kms/hr/sec Meters/sec/sec0.2778 gal/min liters/sec 0.06308 gal/min cu ft/hr 8.0208 110
Technical Data onversion Factors TO ONVERT INTO MULTIPLY Y TO ONVERT INTO MULTIPLY Y Kilowatts TUs/min 56.92 Newton kgs 0.1020 kws ft-lbs/min 4.425 x 10 4 kws ft-lbs/sec 737.6 Ounces lbs 1.805 kws hp 1.341 ozs gram 28.349527 kws kg-calories/min 14.34 kws watts 10 3 Ounces (Fluid) cu in 1.805 ozs (fluid) liters 0.02957 Kilowatt-Hrs TUs 3415 kw-hrs ft-lbs 2.655 x 10 6 Pounds ozs 16 kw-hrs hp-hours 1.341 lbs tons (short) 0.005 kw-hrs kg-calories 860.5 lbs newtons (N) 4.44 kw-hrs kg-meters 3.671 x 10 5 lbs gram 453.5924 Liters ccs 103 Lbs of Water cu ft 0.01605 liters cu ft 0.03531 lbs of water cu in 27.73 liters cu ins 61.02 lbs of water gals 0.1204 liters liters cu meters gals 10-2 0.2642 Lbs of Water/Min cu ft/sec 2.679 x 10-4 liters quarts (liq) 1.057 Pounds/u Ft lbs/cu in 5.787 x 10-4 Liters/Min gals/sec 4.403 x 10-3 Pounds/u In lbs/cu ft 1728 Meters cms 100 meters ft 3.281 Pounds/Sq In atms 0.06804 meters ins 39.37 lbs/sq in ft water 2.311 meters kms 10 3 lbs/sq in in mercury 2.036 meters mms 10 3 lbs/sq in kgs/sq cm 0.07031 meters/min cms/sec 1.667 meters/min ft/min 3.281 Radians degrees 57.29578 meters/min ft/sec 0.05468 meters/min kms/hr 0.06 Tons (Long) kgs 1016 meters/min miles/hr 0.03728 tons (long) lbs 2240 tons (long) tons (short) 1.12000 Meters/Sec ft/min 196.8 meters/sec ft/sec 3.281 Tons (Short) kgs 2000 meters/sec kms/hr 3.6 tons (short) kps 907.18486 meters/sec kms/min 0.06 tons (short) tons (long) 0.89287 meters/sec miles/hr 2.237 tons (short) tons (metric) 0.90718 meters/sec miles/min 0.03728 Watts TUs/min 0.05692 Micron meters 10-6 watts ft-lbs/min 44.26 microns in 39 x 10-6 watts ft-lbs/sec 0.7376 watts hp 1.341 x 10-3 Miles/Hr cms/sec 44.70 watts kg-calories/min 0.01434 miles/hr ft/min 88 watts kws 10 miles/hr ft/sec 1.467 miles/hr kms/hr 1.609 Watts/Hours TUs 3.415 miles/hr meters/min 26.82 watts/hrs ft-lbs 2655 watts/hrs hp-hrs 1.341 x 10-3 Millimeters cms 0.1 watts/hrs kg-calories 0.8605 mms ins 0.0397 watts/hrs kg-meters 367.1 watts/hrs kw-hrs 10-3 Minutes (ngle) radians 2.909 x 10-4 111
Technical Data Temperature onversion Look up reading in middle column (shaded). If in degrees entigrade, read Farenheit equivalent in right-hand column; if in Farenheit degrees, read entigrade equivalent in left-hand column. F = ( X 1.8) +32 = ( F - 32) X.5556 F F 51 60 76 46 50 58 40 40 40 34 30 22 29 20 4 23 10 14 17.8 0 32 17.2 1 33.8 16.7 2 35.6 16.1 3 37.4 15.6 4 39.2 15.0 5 41.0 14.4 6 42.8 13.9 7 44.6 13.3 8 46.4 12.8 9 48.2 12.2 10 50.0 11.7 11 51.8 11.1 12 53.6 10.6 13 55.4 10.0 14 57.2 9.4 15 59.0 8.9 16 60.8 8.3 17 62.6 7.8 18 64.4 7.2 19 66.2 6.7 20 68.0 6.1 21 69.8 5.6 22 71.6 5.0 23 73.4 4.4 24 75.2 3.9 25 77.0 3.3 26 78.8 2.8 27 80.6 2.2 28 82.4 1.7 29 84.2 1.1 30 86.0.6 31 87.7 0 32 89.6 F F.6 33 91.4 1.1 34 93.2 1.7 35 95.0 2.2 36 96.8 2.8 37 98.6 3.3 38 100.4 3.9 39 102.2 4.4 40 104.0 5.0 41 105.8 5.6 42 107.6 6.1 43 109.4 6.7 44 111.2 7.2 45 113.0 7.8 46 114.8 8.3 47 116.6 8.9 48 118.4 9.4 49 102.2 10.0 50 122.0 10.6 51 123.8 11.1 52 125.6 11.7 53 127.4 12.2 54 129.2 12.8 55 131.0 13.3 56 132.8 13.9 57 134.6 14.4 58 136.4 15.0 59 138.2 15.6 60 140.0 16.1 61 141.8 16.7 62 143.6 17.2 63 145.4 17.8 64 147.2 18.3 65 149.0 18.9 66 150.8 19.4 67 152.6 20.0 68 154.4 20.6 69 156.2 21.1 70 158.0 21.7 71 159.8 F F 22.2 72 161.6 22.8 73 163.4 23.3 74 165.2 23.9 75 167.0 24.4 76 168.8 25.0 77 170.6 25.6 78 172.4 26.1 79 174.2 26.7 80 176.0 27.2 81 177.8 27.8 82 179.6 28.3 83 181.4 28.9 84 183.2 29.4 85 185.0 30.0 86 186.8 30.6 87 188.6 31.1 88 190.4 31.7 89 192.2 32.2 90 194.0 32.8 91 195.8 33.3 92 197.6 33.9 93 199.4 34.4 94 201.2 35.0 95 203.0 35.6 96 204.8 36.1 97 206.6 36.7 98 208.4 37.2 99 210.2 37.8 100 212.0 43 110 230 49 120 248 54 130 266 60 140 284 66 150 302 71 160 320 77 170 338 82 180 356 112
General Information Metal Tubing/Fitting Reference Guide Maximum Tube Operating Size Tube Pressure Tubing O.D. Wall (PSI) Fittings 1 /8.030 4300 3 /16.030 2850 1 /4.030 2100 OPPER 5 /16.032 1800 Hi-Duty DED SOFT 3 /8.032 1500 45 Flare SEMLESS 1 /2.032 1150 Hi-Seal rass STM 75 5 /8.035 1000 NSI H23.3 3 /4.035 850 7 /8.035 650 1 /8.030 400 3 /16.030 400 ompresamatic OPPER 1 /4.030 300 ompression DED SOFT 5 /16.032 300 Omega Flo SEMLESS 3 /8.032 500 Poly-Flo with Universal Sleeve* STM 75 1 /2.032 200 Poly-Flo Kwik-onnect ouplings* NSI H23.3 5 /8.035 150 (1/4 & 3/8 O.D.) with 261U 3 /4.035 150 Universal Nut & Sleeve Tube Tubing Size Tube Not Tubing Tubing O.D. Wall elled elled Fittings 1 /8.030 1000 2000 3 /16.030 750 1500 OPPER 1 /4.030 500 1000 DED SOFT 5 /16.030 500 1000 SEMLESS 3 /8.032 350 700 STM 75 1 /2.032 200 500 Flex NSI H23.3 5 /8.035 400 3 /4.035 350 7 /8.035 300 1 /8.062 3000 OPPER PIPE 1 /4.082 3000 RED RSS 3 /8.090 3000 rass Pipe* STM 43 1 /2.107 2000 1 /8.028 4600 STEEL 3 /16.028 4000 OPPER 1 /4.034 3600 RZED 5 /16.034 2750 45 Flare (UNDY) 3 /8.042 2500 STM 254 1 /2.049 2250 DOULE LP FLRE 5 /8.049 2100 1 /8.028 6050 3 /16.028 4180 1 /4.035 3800 5 /16.035 3340 STEEL 3 /8.049 3960 SEMLESS 1 /2.049 2900 SE J524 5 /8.049 2280 Hi-Seal Steel* WELDED 3 /4.049 1880 SE J525 7 /8.065 2150 1.065 1860 1 1 /4.083 1920 1 1 /2.083 1580 Tube Type Type Size Tube 316 17-4 PH Tubing O.D. Wall Sleeves Sleeves Fitting 1 /8.028 8180 8180 STINLESS 3 /16.028 5650 5650 STEEL 1 /4.035 5900 5900 NNELED 3 /8.049 5500 5500 SEMLESS 1 /2.049 4100 4100 TYPE 304 5 /8.049 3300 3300 Hi-Seal Stainless Steel* STM 213 3 /4.049 2700 2700 1.065 2510 1 1 /4.083 2580 1 1 /2.083 2130 * onsult factory for further information.