Come in from the sun A

Come in from the sun Welcome to a new generation of tanning products. While the concept of sunless tanning lotions is not a new one, technology has finally caught up. The Sunless Express Spray Spa is the culmination of countless hours of research on methods of applying sunless tanning lotion. Sunless tanning products work by creating a response with the top two layers of your skin. Dihydroxyacetone, or DHA, reacts naturally with the protein in your skin. A brown tan forms within approximately two to three hours after your session, and continues to darken for up to 24 hours. The result is a substantive tan. It is absolutely water-resistant and diminishes only as the dead cells of the skin flake off - usually one to two weeks. DHA is a common chemical used in multiple ways throughout our normal everyday lives. For example, DHA is often used as an additive in food and cosmetics. Please take the time to read through this guide to familiarize yourself with the concept of sunless tanning and the proper usage of your new equipment. Thank you, and Welcome once again! i

Introduction - contents Safety Information...............................iii Get to Know the Sunless Express...................1 Operation.....................................5 Before you tan...............................6 During the tan...............................6 Safety features...............................7 After the tan.................................7 Advanced controls............................8 Setting the clock..............................9 Care and Maintenance...........................10 Cleaning after use............................10 Before you turn out the lights...................10 Changing/refilling solutions.....................11 Thorough periodic cleaning....................11 Mechanical inspection........................12 Component maintenance......................12 Remote Connections............................13 Troubleshooting................................16 Warranty information............................18 Technical Information.....................back cover ii

Safety Information DANGER Shock hazard. Disconnect power before servicing. If the supply cord is damaged, it must be replaced by a special cord available from the manufacturer or its service agent. WARNING This product does not contain a sunscreen and does not protect against sunburn. Repeated exposure of unprotected skin while tanning may increase the risk of skin aging, skin cancer, and other harmful effects to the skin even if you do not burn. Avoid spraying directly into eyes. CAUTION Read and follow all instructions regarding use and operation of the Sunless Express. IMPORTANT Press the Stop button at any time to stop operations immediately. This product is in compliance with applicable requirements of UL 60335-1, IEC 335-2-23, and CAN/CSA-E335-1/3E-94. iii 88465

Safety Information DANGER Risque de chocs électriques. Débrancher l alimentation électrique avant de procéder à la réparation ou à l entretien de l appareil. Un cordon d alimentation endommagé doit être remplacé par un cordon particulier pouvant être acheté du fabricant ou d un technicien. AVERTISSEMENT Ce produit ne contient pas d écran solaire et ne protège pas contre les coups de soleil. L exposition répétée d une peau non protégée aux rayons ultraviolets peut accroître les risques de vieillissement et de cancer cutané et produirent d autres effets nocifs même en l absence de coups de soleil. Éviter de pulvériser le produit dans les yeux. MISE EN GARDE Lire et suivre toutes les directives d utilisation et de fonctionnement du spa Sunless Express. IMPORTANT Pour que l appareil cesse immédiatement de fonctionner, appuyer en tout temps sur le bouton Stop (Arrêt). Ce produit est conforme aux normes de rendement dans le documents UL 60335-1, IEC 335-2-23, CAN/CSA-E335-1/3E-94. iv 88465

Getting to Know the Sunless Express (The tanning area) SPEAKER WASHDOWN NOZZLE GANTRY SPRAY NOZZLE SPRAY MANIFOLD 1

Getting to Know... (Lower section of Control Cabinet) WATER HEATER AIR PUMP PUMPS (see next page) DISINFECTANT TANNING LOTION 2

Getting to Know... WASHDOWN SOLENOID EVACUATION FAN (at top of cabinet) PERISTALTIC PUMP EVACUATION PUMP 3

Getting to Know... (Control Module) REMOTE PORTS (not currently used) T-MAX LINK RS-232 PORT (not currently used) CONTROL PORT LIGHTS WASHDOWN CONTROL PAD MASTER POWER 4

Operation Operation of the sunless tanning booth requires just two buttons. The first is the Start/Stop button on the Sunless Express Remote Control (SERC) supplied with the booth (see illustration 1). Pressing this button sends a signal to the booth to allow a single session to run. After the session is complete the display on the SERC will indicate a.. meaning the room needs to be sanitized. After cleaning the unit press the up ( ) button on the SERC until a 0 appears. Once the Start/Stop button (on the SERC) is pressed the booth receives the signal and is ready for the session. Enter the booth, close the door and an automated voice will explain the sunless tanning experience. Press the green Start button on the wall to begin (see illustration 2). The SERC is also capable of telling the booth to run two back-to-back sessions without resetting. To do this, press the up ( ) button until the display shows a 4 (signifying the Spray Manifold will make four passes over your body). Read on for tanning instructions as well as a complete script of the tanning session. Refer to Remote Connections - Operation with remote for operation while connected to a T-Max remote system. 5 Illustration 1 (SERC) Illustration 2

Operation - the tanning session Before you tan For best results, exfoliate before using the tanning unit. Do not use lotion on your body before you tan. This may act as a barrier and prevent some areas from getting tan. Remove any makeup from face. Remove contacts. Remove all jewelry. Women: Place the shower cap right at the hairline. This will prevent any unnecessary tan lines on your forehead. Men: If you have a receding hair-line or balding - to prevent tan-line, do not wear the shower cap unless your hair is naturally very light or is chemically lightened. Apply neutralizing lotion to hands and toes with special attention to cuticle coverage. Be careful not to apply neutralizing lotion to areas you want tan as white spots will result. You may remove any misplaced blocker with a moisture wipe. During the tanning session Upon closing the door you will hear the following instructions... Welcome to the Sunless Express spray spa! For best results, follow the instructions exactly. Please place your feet in the boxes and stand as close to the door as possible. Point your toes toward the sides. Place your arms above your head and bend elbows slightly. Palms should be facing forward. Raise your chin upward. To hear the instructions again open the door and close it one time. Press the green start button to begin your session and again, place your hands above your head, palms facing forward. See the chart located on the rear wall of the booth for complete positioning instructions. Pressing the Start button will begin the tanning session. At the end of the countdown, close your eyes and hold your breath as the spray passes your upper body. 3,2,1. The spray mist will coat the front of your body. 6

Operation - the tanning session You may open your eyes and breathe freely. Please turn around and face the door. Please place your feet in the boxes and stand as close to the door as possible. Point your toes toward the sides. Place your arms above your head and bend elbows slightly. Palms should be facing the door. Press the green start button to begin your session and again, place your hands above your head, palms facing the door. At the end of the countdown, close your eyes and hold your breath as the spray passes your upper body. 3,2,1 The spray will now coat the back side of your body. Thank you for using the Sunless Express spray spa. At this time you may open your eyes and breathe freely. Upon exiting the spa, please dry off with the towels provided. Enjoy your tan. 7 Safety features Panic Stop Button - Pressing the Stop button will immediately end the session at any time. Gantry Safety Mechanism - If there is any pressure placed on the spray manifold during operation, the unit will stop and the session will end. Check the mechanism for any obstructions before using again. After the tan After your session, you will notice a light mist on your body. First, wipe your hands with the moisture wipes. Next, gently wipe the rest of your body, as if getting out of the shower. When you are completely dry, wipe your hands again with the moisture wipes in case your hands came in contact with the solution while drying off. Be sure you are completely dry before getting dressed. This will eliminate most of the bronzer residue on the inside of your clothing. You will not notice a lot of immediate color from your session. The tan will begin to develop within 2 to 3 hours after the session and continue to darken for up to 24 hours. Wait 4-6 hours before showering or engaging in activities which encourage persperation as this will wash the bronzer off your body before it has enough time to affect the color of your skin.

The Control Pad, located on the Control Module, offers additional controls for the salon owner. The illustration at right shows the Home screen, with the time and a scrolling message. After making adjustments, waiting 10 seconds will return the screen to Home. Operation - advanced controls Execute [ ] Up [ ] Down [ ] - press to enter modes and select options - scrolls options upward - scrolls options downward Cycle Count [ ] Displays number of complete sessions performed Status [ ] [ ] [ ] Tanning Booth [ ] [ ] [ ] Door Status (open/closed) Light Status (on/off) Software Vers [ ] Displays software version number Home [ ] [ ] [ ] Controls [ ] [ ] [ ] Sound Version [ ] Tanning Cycle [ ] Washdown Cycle[ ] Panic [ ] Displays voice version number Starts a tanning cycle. Press [ ] again to finish the cycle Starts a washdown cycle Interrupts the tanning session [ ] [ ] Booth Lights [ ] Turns lights on and off Clock [ ] Set time (see next page) Settings [ ] [ ] [ ] Volume Calibrate 8 [ ] [ ] [ ]/[ ] to adjust volume Resets position of spray manifold

Operation - advanced controls Setting the clock From the Home screen, press Execute [ ] to enter the option mode. Scroll through the three options using the Up [ ] or Down [ ] buttons, until you reach the Settings option. Press [ ] again to enter the Settings menu. Scroll to the Clock option and press [ ]. The hours digit on the time will blink. Press [ ] or [ ] until the desired hour is displayed. Press [ ]. The minutes blink. Set the minutes and press [ ] and then [ ] or [ ] to set am or pm. Wait a few seconds or press [ ] one more time to exit the setting mode. Home [ ] [ ] [ ] Settings [ ] [ ] [ ] Clock [ ] Hours blink [ ]/[ ] to adjust hours. [ ] to set Minutes blink [ ]/[ ] to adjust minutes. [ ] to set am or pm blinks [ ]/[ ] to select. 9 [ ] to set

Care and Maintenance Your Sunless Express spray spa has been designed and engineered for years of service. However, much like changing the oil in your car, there are some care and maintenance issues to keep in mind. The next few pages outline the various periodic duties you need to perform broken down by frequency. Refer to the pictures in Getting to Know the Sunless Express. WARNING Shock hazard. Disconnect power before servicing. Cleaning after use After each use it is necessary to clean and disinfect the booth by activating the Washdown cycle. 1. Close the door and press the Washdown button on the Control Module located in the Control Cabinet. 2. After the Washdown cycle is complete, wipe the internal walls. You may use the squeegee provided or a soft towel. 3. Disinfect and dry the step and door handles. 4. Reset the remote control unit by holding the up button until the display reads 0. Before you turn out the lights At the end of each day of usage there are a few things to check to make sure the unit continues to function satisfactorily. 1. Stand the inside mat up on edge to allow it to dry and encourage air movement within the base cavity. 2. Be sure to leave the door open. 3. Check the level of tanning and disinfectant solution. Try not to let the levels drop below about 1 1/2 inches to avoid running dry. 10

Care and Maintenance Thorough periodic cleaning On a monthly basis a little extra care is needed. 1. Thoroughly clean the internal walls, rubber seals and spray manifold to remove any solution residue. 2. Remove the Floor Mat and Floor Mat Plate and use a hose to spray them off. 3. Clean the outside of the unit as needed using non-ammonia cleaners. 4. Replace the solution bottle with one containing only water and run the unit for a complete cycle to purge the system. 5. While the solution bottle is removed, rinse the solution filters in warm water. Changing/refilling solutions For best results, the level of tanning solution and disinfectant should not be less than 1 1/2 inches. When changing solutions you may pour any remaining liquid from the used bottle into the new one if there is enough room in the new bottle. 1. Lift the tanning solution and/or disinfectant container out of the Spill Tray and place on the floor. 2. Remove the cap, complete with the hose, from the used container. 3. Remove the cap from the replacement container and screw onto the used container to save any unused solution. 4. Insert the solution filter hose into the new container and secure the cap. 5. Place new bottle into Spill Tray. 6. Check to verify the solution filter hose touches the bottom of the container. 11

Care and Maintenance Mechanical inspection Along with the monthly thorough cleaning, inspect the unit s mechanical integrity. 1. Inspect all bolts, nuts, screws and other fasteners to make sure all are secure. 2. Check door hinges for signs of wear. 3. Pay special attention to the Spray Manifold track system and belt for signs of wear. This is the heart of the unit. 4. Inspect the counterweight for smooth movement by sliding it up and down its guide. It should glide freely. 5. Check all hose connections, pumps, valves and water heater for leaks. 6. Make sure the AC power cord is in good shape and firmly plugged in at both ends. 7. Check all filters and clean or replace those which appear dirty. 8. Check proper operation of the gantry safety system... With the solution system off, turn unit on. Press down on the Spray Manifold as it rises. It should stop without much force. 9. Clean the spray nozzles carefully. 12 Component maintenance 1. Purge the water heater per manufacturers requirements. 2. Maintain Waster pump per manufacturers requirements. 3. The Evacuation Fan needs no regular maintenance. 4. Clean unit as described in Thorough periodic cleaning.

Remote Connections T-Max Products Your Sunless Express remote control unit incorporates advanced circuitry allowing it to connect and communicate with the popular T-Max remote control systems. The booth can be connected to any T-Max Manager or 1A or 3A. Refer to the appropriate section that follows. T-Max Manager Remote System This system is ideal for multiple sunbed installations, including the Sunless Express. Simply connect the RJ-22 modular cable(s), described in the T-Max Manager manual, into the remote port(s) located on the back of the Sunless Express Remote Control (SERC) and follow the instructions that came with your remote system. If you have an older T- Max Manager that does not support auto addressing, set the address of the SERC manually as described in Setting the address manually. You can place your booth at any location in the series (see illustration below). 13 T-Max 1A and 3A Remote Systems The T-Max 1A and 3A can offer the same control as the T-Max Manager in single unit installations. If you re using a 1A, it must have a chip labelled master installed on its circuit board. After you have set the T-Max 1A s, or 3A s, address to 0 (refer to your T-Max user s guide) and the SERC s address to 1, simply connect the RJ-22 modular cables, described in the T-Max user s guide, directly into either port located on the back of the SERC and either port on the back of the T-Max 1A or 3A. Setting the address manually Before connecting the SERC to the T- Max Manager or T-Max 1A or 3A, the address must first be set. Set the address manually as described below. 1. Remove power from the T-Max Manager or 1A or 3A. 2. Plug in the SERC. It should show 9.9 on the display and sound an alarm. If it just shows 0 go to step 4. 3. Press and release the Start/Stop button. The display will flash 8.8 and the alarm will stop. Press the Up button until the display stops flashing and shows a 0.

Section - subheading 4. Press and hold the Start/Stop and Up buttons simultaneously until a.1 appears. This may take about 5-6 seconds. Release the buttons. 5. Press the Start/Stop button. A flashing number will appear. This is the address that the SERC is set to. 6. Press the Up or Down button until the desired address is displayed. Note: When setting the addresses, remember these three rules; Each tanning unit in the salon (including the SERC) needs a unique address. Do not set the SERC to 00. If the period is flashing, you are over address 100. 7. Once the desired address is displayed, press and release the Start/Stop button. A steady.1 will be displayed. 8. Press and hold both the Up and Down buttons until a 0 is displayed. 9. Connect the SERC into the remote series. 14 Operation with remote When connected to a T-Max system the unit operates differently than explained in Operation. The session is activated from the Manager, 1A or 3A. To activate a single session send a 2 from the remote (refer to your T-Max manual). For a double session, send a four (4). This will activate the unit and the session starts when the tanner enters the booth and presses the Start button inside the unit. The use of two and four correspond to the number of passes the Spray Manifold will make over your body during the session. After the session is complete the SERC will display.. indicating the room needs cleaning. Refer to Care and Maintenance - Cleaning after use for cleaning instructions. After cleaning, press the Up button on the SERC to clear the.. indication and ready the unit for the next session.

Notes 15

Troubleshooting Problem Overhead lights not working Unit will not start session once the green button is on Unit stops in mid session Manifold is not moving during session Unit will not work with T-Max Solution 1. Check power supply to unit 2. Check light power cord to control module 3. Press lights button on control module 4. Replace light(s) 1. Is the SERC displaying a flashing decimal after the 0? If not, press the Start/Stop button 2. Check supply cord to switch 1. Check gantry/belt for interference 2. Check counterweight for interference 3. Check gantry/belt for clip disconnection 4. Manifold may have tripped the safety switch 1. Check gantry/belt for interference 2. Check counterweight for interference 3. Check gantry/belt for clip disconnection 4. Manifold may have tripped the safety switch - Safety signal will be voiced 1. Check all connections 2. Make sure each unit has a unique address 3. Has the T-Max Manager been disconnected 4. Has the T-Max system been set-up correctly Solution is not coming through nozzles, air only 1. Check solution level 2. Check peristaltic pump for proper action 3. Check solution hoses and connections for leaks or disconnection 16

Troubleshooting Problem Air is not coming through nozzles, solution only Manifold making loud pounding noise at the top Nothing comes on Footwash feels cold Footwash not working Washdown not working Users are consistently darker on one side The unit is overly foggy during session Solution 1. Check air hoses for disconnection 2. Check air pump for proper function Unit has not made contact with limit switch or bottom of cycle. Adjust switch. 1. Check main power and connection 2. Check GFCI 3. Check control Module fuse 1. Check heater setting 2. Check power cord connection Check solenoid and or harness connection Check solenoid and or harness connection Check nozzles for clogs 1. Check ventilation fan power supply 2. Check duct connections 3. Replace ceiling filter 17

Sunless Express LIMITED LIFETIME WARRANTY Warranty The manufacturer of your Sunless Express spray unit warrants your spray unit to be free of structural defects in its material and workmanship, under normal use, for its lifetime. The manufacturer will, at its discretion, repair any structural defect which materially affects the performance of the spray unit, or replace the spray unit. For six (6) months from the date of purchase, the manufacturer will provide replacements for parts that prove to be defective in material or workmanship. Labor costs associated with repair or replacement work covered by this Sunless Express Limited Lifetime Warranty will be reimbursed for repair or replacement work required to be performed during the thirty (30) day period following the shipping date of your spray unit. Normal wear and tear, damage from misuse or abuse, damage incurred in transit or damages resulting from unauthorized repairs or modifications, or the use of unauthorized spray solutions, are not covered by this warranty. Warranty coverage does not include cosmetic abnormalities such as scratches, nicks or dents that do not materially interfere with the function of the spray unit. THIS SUNLESS EXPRESS LIMITED LIFETIME WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MER- CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY DISCLAIMED. No one has the authority to change or modify this Sunless Express Limited Lifetime Warranty in any respect. IN NO EVENT SHALL THE MANUFACTURER OR DISTRIBUTOR OF YOUR SPRAY UNIT BE LIABLE AT LAW OR IN EQUITY FOR ANY LOSS, LIABILITY, DAMAGE OR EXPENSE IN AN AMOUNT IN EXCESS OF THE PURCHASE PRICE RECEIVED, OR FOR LOSS OF USE OR PROFITS, LOSS OF TIME, INCONVE- NIENCE, RENTAL OR SUBSTITUTE PRODUCTS, LOSS OF BUSINESS, LOSS OF INCOME, OR ANY OTHER INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This Sunless Express Limited Lifetime Warranty gives you specific, legal rights and you may have other rights which may vary from state to state. All warranty service must be performed by an authorized Sunless Express service person. All labor charges must be authorized by the manufacturer prior to the start of repairs and must not exceed the established rates and time allotment policies established by the manufacturer. If your spray unit must be returned for service, all freight charges shall be at your expense. This warranty is extended to the individual or legal entity whose name appears on the original sales document and may not be transferred to any other individual or legal entity. This warranty is void if the spray unit is modified in any manner from its original design or if the spray unit is used with a spray solution other than one supplied by ETS, Inc. To file a Warranty Claim, please follow these steps: 1. Locate the serial number on the spray unit, found (to be determined). 2. Proof of purchase must be provided before any claim will be considered. 3. Contact the Sunless Express Service Hotline at 877-783-8368. 18

Size Sunless Express Spray Spa Weight (Pounds) 950 Minimum Room Size 7 wide x 9 long x 10 tall Electrical - Voltage (AC) 110 Amperage 13 Circuit Breaker (Amps) 20 Outlet (NEMA standard) 5-20R Remote Capability T-Max compatible CALL FOR SERVICE OR QUESTIONS: 1 877 783 8368 6270 Corporate Drive, Indianapolis, IN 46278-2900