The MAXX Press D I G I T A L C L A M OPERATOR S MANUAL 6 x0 x5 5 x5
Safety Instructions When using your heat press, basic precautions should always be followed, including the following:.. 3.. 5. 6. 7. 8. 9. 0.. Read all instructions. Use heat press only for its intended use. To reduce the risk of electric shock, do not immerse the heat press in water or other liquids. Never pull cord to disconnect from outlet, instead grasp plug and pull to disconnect. Do not allow cord to touch hot surfaces, allow heat press to cool completely before storing. Do not operate heat press with a damaged cord or if the equipment has been dropped or damaged. To reduce the risk of electric shock, do not disassemble or attempt to repair the heat press. Take it to a qualified service person for examination and repair. Incorrect assembly or repair could increase the risk of fire, electric shock, or injury to persons when the equipment is used. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Close supervision is necessary for any heat press being used by or near children. Do not leave equipment unattended while connected. Burns can occur when touching hot metal parts. To reduce the likelihood of circuit overload, do not operate other high voltage equipment on the same circuit. If an extension cord is necessary, then a 0 amperage rated cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. Product Warranty Registration Log onto www.hotronix.com/registration You must provide the Hotronix heat press serial number and model information. S E R V I C E H O T L I N E : 8 0 0. 7 7. 8 5 0
The MAXX Press Table Of Contents Safety Instructions Machine View Control Panel Guide Operating Instructions Connecting the System Turning the System On Adjusting the Temperature Adjusting the Time Adjusting the Pressure Pressing Replacement Parts List 5 6-6 7 8 9 0 Parts Location Guide 3 Electrical Schematic Contact 5 H O T R O N I X. C O M
The Machine MAXX View Press FRONT VIEW LED Display Located in the Back of the Press Circuit Breaker Power Supply Over-the-Center Pressure Adjustment Knob SIDE VIEW Lift Handle Power ON/OFF Switch ON OFF PAGE S E R V I C E H O T L I N E : 8 0 0. 7 7. 8 5 0
MODE The Control MAXX Panel Press Guide Digital Display Temperature Indicator Set Indicator MODE Time Indicator Increase Mode Select Decrease H O T R O N I X. C O M PAGE 5
T Operating he MAXX Instructions Press The MAXX Press DIGITAL CLAM The MAXX Press Digital Clam Operating Instructions are designed with the user in mind. Carefully read and follow the step-by-step instructions for best results. To avoid burns, do not touch the heated platen during use. Keep hands clear of the upper platen of the press during platen lock down as the pressure may cause injury. Press should be placed on a sturdy, suitable stand at least 36 L x W x 9 H. Work area must be kept clean, tidy and free of obstructions. Power supply cord must be disconnected before cleaning or servicing press.. Connecting the System CONNECT THE POWER CORD. Connect the power cord into a properly grounded electrical outlet with a sufficient amperage rating. VOLTAGE: 0 Volt - The MAXX Press Digital Clam requires a full 0 amp grounded circuit for 0 volt operation. 0 Volt - The MAXX Press Digital Clam requires a full 0 amp grounded circuit for 0 volt operation. EXTENSION CORDS: If used, should be as short as possible and not less than gauge. Heavy duty cords are recommended. CIRCUITS: that have less than 5 amps or that have other high demand equipment or heat presses plugged in should not be used. NOTE: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid hazard. Use SJT type rated 300 V cord for replacement. CAUTION: Failure to follow these instructions will cause:. Erratic controller functions.. Inaccurate displays and slow heat-up. 3. The circuit breaker to disengage. PAGE 6 S E R V I C E H O T L I N E : 8 0 0. 7 7. 8 5 0
. The MAXX Press Turning the System On SWITCH THE SYSTEM ON See the diagram below for switch placement. Locate the lift handle and position the heat platen in the UP (load) position. Power ON/OFF Switch ON OFF Now, locate the Power ON/OFF Switch on the side of the press, then turn the Power Switch on. H O T R O N I X. C O M PAGE 7
T he MAXX Press 3. Adjusting the Temperature ADJUST THE TEMPERATURE Locate the LED Display on the Press. 3. 3. Press the Mode Select button located in the center of the Control Panel. The (SET) and (TEMP) lights located next to the display will illuminate indicating you are in the adjust temperature mode. Next, press the (-) button located to the left of the Mode Select button to lower the temperature setting, or press the (+) button located to the right of the Mode Select button to raise the temperature setting. The temperature can be set from 05 F (96 C) to 30 F (0 C). The LED will display changes as you make them. Digital Display Temperature Indicator Set Indicator MODE Time Indicator Increase Mode Select Decrease NOTE: The temperature indicator will only display temperatures 00 F (93 C) and up. PAGE 8 S E R V I C E H O T L I N E : 8 0 0. 7 7. 8 5 0
. ADJUST THE TIME The MAXX Press Adjusting the Time Once you have adjusted the temperature, press the Mode Select button again. This will advance you to the Time mode. The set and time lights will illuminate, indicating that you are in the Time mode. Adjust the time in the same manner that you adjusted the temperature. Select the desired time and push the Mode Select button again to exit the time settings. All lights will be off and the press will return to the Print Mode. H O T R O N I X. C O M PAGE 9
T he MAXX Press Adjusting the Pressure 5. ADJUST THE PRESSURE The MAXX Press Digital Clam features a patented, Over-the-Center Pressure Adjustment located in the center of the heat platen. Adjust the pressure by turning the knob clockwise to increase pressure and counter clockwise to decrease pressure. Over-the-Center Pressure Adjustment Knob REMEMBER: To allow for the thickness of your garment when adjusting the pressure. WARNING: Structural damage caused by excessive pressure is not covered under the limited warranty! PAGE 0 S E R V I C E H O T L I N E : 8 0 0. 7 7. 8 5 0
6. PRESS The MAXX Press Printing/Pressing Once your equipment has reached the designated temperature, position the garment and application and proceed to press. Lower and lock the heat platen into the press position. This procedure will start the automatic timing process. 6.3 The timer will automatically count down and audibly signal you to lift the heat platen into the UP position when the press cycle is complete. The time will automatically re-set and you are ready to continue with the next application. H O T R O N I X. C O M PAGE
T Replacement he MAXX Parts Press List Item # Part Name Part # Qty. 3 A-B 5 6 7 A-B 7 C 8 9 0 A 0 B-C 3 5 6 7 A 7 B 7 C 8 A 8 B 8 C 9 A 9 B 9 C 0 A 0 B 0 C 3 5 6 A-B 6 C 7 8 9 30 3 3 33 3 35 A-B-C 36 37 38 39 0 3 A-B-C 5 6 7 A-B-C 8 9 50 5 5 53 5 55 56 Hex Soc Button HD # 0-3 x / Rubber Foot Acorn Hex Nut Hex Cap HD Screw - 3/8-6 x 3/ 6 x 0 5 x 5 Lock Spring Washer Hex Soc Screw / - 0 x / Lower Platen Spacer 6 x 0 5 x 5 Lower Platen Spacer x 5 Nylon Hex Nut Ball Stud - 0mm Gas Spring 6 x 0 Gas Spring 5 x 5 x 5 Steel Spacer Bridle Links Nylon Washer Threaded Pin / - 0 x 3 PVC Spacer / I.D. x.8 Threaded Pin 3 5/8 x.5 Dia. _/ - 0 Lower Platen 6 x 0 Lower Platen 5 x 5 Lower Platen x 5 Silicone Pad Gray 6 x 0 Silicone Pad Gray 5 x 5 Silicone Pad Gray x 5 Heat Platen 6 x 0 Heat Platen 5 x 5 Heat Platen x 5 Heat Platen Cover 6 x 0 Heat Platen Cover 5 x 5 Heat Platen Cover x 5 Finish Washer Cover Screw 0 - x / Adjustment Spindle Pressure Adj. Knob Safety Bolt - 8 x / Elbow 90 degress with tubing 6 x 0 5 x 5 Topaz Connector with flex tubing x 5 Shoulder Bolt Steel Pin / Dia. x.38 Soc HD Cap Screw / - 0 x 3/8 Hex HD Nut - / - 0 Steel Pin - / Dia. x 6.5 PVC Spacer - /.D. x. Nylon Nut Rubber Foot Adjustment Arm Assembly 6 x 0 5 x 5 x 5 JCN Nut Foam Grip PVC Spacer / I.D. x 5 All Thread Pin - / - 0 x 3/ Lift Links Hucap / Magnet Magnet Bracket Handle Assembly 6 x 0 5 x 5 x 5 Phillips Pan HD Screw - #6-3 x / Housing Base Assembly 6 x 0 5 x 5 x 5 Proximity Switch Terminal Block Triac Controller Bracket SSTT Control Board On/Off Switch Circuit Breaker Display Overlay Probe 3-0 - 6-56 3-0 - 8 3-0 - - 006-3 3-0 - 6-79 00-006 - 0-939 - 3-6 - KIT 3-6906 - 08-3 - 09-098 - 09-09 3-086 3-99 - - 0-73 - 875-00 - 3 3-30 3-99 3-33 3-337 3-33 - 063 3-0 - 7-08 - 0 3-0 - 38-90 - 353 3-0 - 55-093 3-0 - 5-006 - - 09-097 - 006-0 - 56 KIT 3-6903 - 006 - -50-096 - 0 - KIT 3-6905 - 07 - - 9-085 KIT 3-690 3-0 - 5-7 KIT 3-690 - - 90-059 - 66-07 - 087-33 - 08-7 - 6 8 PAGE S E R V I C E H O T L I N E : 8 0 0. 7 7. 8 5 0
The MAXX Press Parts Location Guide The MAXX Press Digital Clam is available in three sizes: 6 x 0, 5 x 5, x 5 When ordering replacement parts, refer to the following color codes For a 6 x0 press - use color code For a 5 x5 press - use color code For a x5 press - use color code A B C 6 A 6 C 0 A 0 B 0 C 9 A 9 B 9 C 8 A 8 B 8 C 7 A 7 B 7 C 7 A 0 A 0 C H O T R O N I X. C O M PAGE 3
The MAXX Press Electrical Schematic US 0 V Version - 50 W for 6 x 0-800 W for 5 x 5-000 W for x 5 0V IMPORTANT: MAKE SURE TO USE CORRECT VOLTAGE CONNECTION TO THE CONTROLLER - 50 W for 6 x 0-800 W for 5 x 5-000 W for x 5 0V US 0 V Version CE 0 V Version - 50 W for 6 x 0-800 W for 5 x 5-000 W for x 5 0V IMPORTANT: MAKE SURE TO USE CORRECT VOLTAGE CONNECTION TO THE CONTROLLER PAGE
Contact Us Stahls Hotronix One Paisley Park Carmichaels, PA 530 U.S.A. Technical Support 800. 77. 850 Monday - Friday 8am - 7pm EST Customer Service 800. 77. 850 Monday - Friday 8am - 5pm EST Replacement Parts 800. 77. 850 8am - 7pm EST Web Hotronix.com This document includes multiple trademarks and describes equipment covered by many patents that are owned by GroupeSTAHL and/or its subsidiaries. GroupeSTAHL enforces its rights to protect these intellectual properties. 0 Rev. A 9- Doc. MAXX - MAXX5 - MAXX0 9-
Proudly made in the U.S.A. One Paisley Park. Carmichaels, PA 530, U.S.A. Tech Support - Customer Service - Replacement Parts: 800. 77. 850 Web: Hotronix.com