Example: Terminal Heads Terminal Head Section User Guide Ø100 105 Ø52 Process Conduit Entry Entry KNC 3/4 M20 x 1.5 4.25 5.53 62 34.5 IP6 200 o C Product Photograph 14 Technical Drawing (measurements in mm) 55 To suit Terminal Blocks with this key code (see pages 15 to 25 for reference). Ingress Protection (IP) rating Temperature rating Terminal Head component breakdown: Silver painting as standard (RAL 9006) Cable Gland (aluminium) *O-Ring (for tight sealing) Material Temp Rating EPDM 140 o C (supplied) SILICON 160 o C VITON 210 o C Conduit Entry *Rubber bush. Process Entry *Please note - the temperature rating of the seal and bush is often lower than that of the head material. Higher temperature materials on request. Temperature Technology Ltd. 2
Aluminium Heads DINA Equivalent to AA Ø90 44.5 92 16 63.5 49.5 39 Ø2 BUZ-H Equivalent to DANAW Ø4 114 Ø56 H-DINA 1/2 BSP M20 x 1.5 6.00 7.0 H-DINA-15.3 15.3mm M20 x 1.5 6.00 7.0 H-DINA-21.3 21.3mm M20 x1.5 6.00 7.0 H-DINA-22.5 22.5mm M20 x 1.5 6.00 7.0 2 H-DINA22.5-PG16 22.5mm PG16 6.00 7.0 H-DINA-32.5 32.5mm M20 x 1.5 6.00 7.0 M24x1.5P H-DINA-M24 M24 x 1.5 M20 x 1.5 6.00 7.0 H-DINA-INT* 9mm M20 x 1.5 6.00 7.0 46mm * Black painting YCE (Double cable entry head) Ø100 H-YCE 1/2 BSP M20 x 1.5.5 11.51 H-YCE-M24 M24 x 1.5 M20 x 1.5.5 11.51 105 Ø52 H-YCE-NPT 1/2 NPT M20 x 1.5.5 11.51 62 40mm 40 o C 14 34.5 55 Supplied without cable gland and bush. KNH(S) H-KNH-S 1/2 BSP M20 x 1.5 6.05 7.7 H-KNH-M24-S M24 x 1.5 M20 x 1.5 6.05 7.7 H-KNH-NPT 1/2 NPT M20 x 1.5 6.05 7.7 1 51 Ø53 13 31 Supplied with screw fastening as standard Can house two transmitters/terminal blocks. Lever kit available 0.5 / 1.19 H-BUZH-S 1/2 BSP M20 x 1.5 6.10 7.93 H-BUZH-S-M24 M24 x 1.5 M20 x 1.5 6.10 7.93 H-BUZH-S-NPT 1/2 NPT M20 x 1.5 6.10 7.93 BUZH-S-22.5 22.5mm M20 x 1.5 6.10 7.93 BUZH-S-M24-12NPT M24x1.5 1/2 NPT 6.10 7.93 Supplied with screw fastening as standard Can house two transmitters/terminal blocks. Lever kit available 0.5 / 1.19 3 Temperature Technology Ltd.
Aluminium Heads KNP(S) Ø2 93 H-KNP-S 1/2 BSP M20 x 1.5 5.00 6. H-KNP-S-34 3/4 BSP M20 x 1.5 5.00 6. 51 13 47 Ø3 Lever kit available 0.5 / 1.2 KNG Ø93 92 Ø37 H-KNG 1/2 BSP M20 x 1.5 6.00 7.0 H-KNG-34 3/4 BSP M20 x 1.5 6.00 7.0 54 Ø43 KNL-E Ø2 101.5 64.5 H-KNL-E 1/2 BSP M20 x 1.5 5. 7.15 55 Ø35 KNE 7 13 46 Ø 3 Please Note: All list prices are subject to change. Check website www.temperaturetechnology.com for up to date information Ø 2 IP6 40o C H-KNE 1/2 BSP M20 x 1.5 4. 5.5 H-KNE-LC 1/2 BSP 1/2 BSP 4. 5.5 H-KNE-34 3/4 BSP M20 x 1.5 5.00 6. H-KNE-5 5/ bore M20 x 1.5 5. 7.15 H-KNE-7 7/ bore M20 x 1.5 5. 7.15 H-KNE-M20 M20 x 1.5 M20 x 1.5 5.00 6. H-KNE-NPT 1/2 NPT 1/2 NPT 5.00 6. H-KNE-M24 M24 x 1.5 M20 x 1.5 5.00 6. H-KNE-1 1 bore M20 x 1.5 5. 7.15 H-KNE-NPTM20 1/2 NPT M20 x 1.5 5.00 6. H-KNE-EPOXY* 1/2 BSP M20 x 1.5 5. 7.15 H-KNE-12-M25 1/2 BSP M25 x 1.5 5.00 6. H-KNE-BLUE** 1/2 BSP M20 x 1.5 5.00 6. *Epoxy painted **RAL 05 Temperature Technology Ltd. 4
Aluminium Heads BUZ Equivalent to DANA Ø4 H-BUZ-S 1/2 BSP M20 x 1.5 5. 7.15 3 Ø56 Ø4 H-BUZ-S-22.5 22.5mm bore M20 x 1.5 5. 7.15 H-BUZ-S-NPT 1/2 NPT M20 x 1.5 5. 7.15 H-BUZ-S-M24 M24 x 1.5 M20 x 1.5 5. 7.15 H-BUZ-S-M24- PG16 M24 x 1.5 PG16 5. 7.15 H-BUZ-S-15.3 15.3mm bore M20 x 1.5 5. 7.15 3 Ø56 Supplied with screw fastening as standard. Lever kit available 0.5 / 1.19 BUZ-W Equivalent to DANAwin Ø4 Ø44 H-BUZ-W-S 1/2 BSP M20 x 1.5 6.00 7.0 3 Window version for viewing transmitter. Lever kit available 0.5 / 1.19 SUZ Equivalent to NAA 73 Ø47.5 Ø6.2 H-SUZ-S 1/2 BSP M20 x 1.5 4.75 6.1 H-SUZ-S-M24 M24 x 1.5 M20 x 1.5 4.75 6.1 H-SUZ-M20 M20 x 1.5 M20 x 1.5 4.75 6.1 H-SUZ-15.3 15.3mm bore M20 x 1.5 4.75 6.1 40.5.5 27mm 40 o C 4 Supplied with screw fastening as standard. Lever kit available 0.5 / 1.19 Contact our Sales Team for assistance. Tel: +44(0)11 9730739 Fax: +44(0)11 9737222 We welcome your enquiries for any Head not listed. www.temperaturetechnology.com 5 Temperature Technology Ltd.
Aluminium Heads KF Wall Mounted H-KF 1/2 BSP M20x1.5 7. 9.75 42.5 14 Ø 2.5 Ø 34 H-KF-34-M20 3/4 BSP M20x1.5 7. 9.75 H-KF-34-12 3/4 BSP 1/2 BSP 7. 9.75 H-KF-M20-M20 M20x1.5 M20x1.5 7. 9.75 12.5 9.5 Please Note Discounts can be given off all list prices dependent upon quantity. H-RTUBE H-M20PLUG H-12PLUG Description Radiation Tube - 115 x 22mm (NPB) Plug - M20 Thread (6mm bore) Plug -1/2 BSP Thread (6mm bore) 5.00 6. 2. 3.25 2. 3.25 H-34PLUG Plug - 3/4 BSP Thread (6mm bore) 2. 3.25 KNC Ø 2 91.5 H-KNC-34 3/4 BSP M20 x 1.5 5. 7.15 13 46 Ø3 KNA-E Ø2 1.5 H-KNA-E 1/2 BSP M20 x 1.5 6.00 7.0 44.5 IP67 40 o C 55 Ø35 KMC Ø 70 6 4 Ø 27 H-KMC 1/2 BSP M20 x 1.5 4.75 6.1 H-KMC-14 1/4 BSP M20 x 1.5 4.75 6.1 H-KMC-M16 M16 x 1.5 M16 x 1.5 4.75 6.1 43 Ø 35 Temperature Technology Ltd. 6
Aluminium Heads KD (Din Form B) Equivalent to BA 72 Ø 42 Ø 2 Ø 72 IP6 40 o C H-KD 1/2 BSP M20 x 1.5 3.5 5.01 H-KD-M M x 1.25 M20 x 1.5 3.5 5.01 H-KD-M20 M20 x 1.5 M20 x 1.5 3.5 5.01 H-KD-M22 1/2 BSP M22 x 1.5 3.5 5.01 H-KD-M24 M24 x 1.5 M20 x 1.5 3.5 5.01 H-KD-PG16 1/2 BSP PG16 3.5 5.01 H-KD-NPT-PG16 1/2 NPT PG16 3.5 5.01 H-KD-M10-PG16 M10 x 1.0 PG16 3.5 5.01 H-KD-M12-PG16 M12 x 1.0 PG16 3.5 5.01 H-KD-6 6mm bore M20 x 1.5 3.5 5.01 H-KD-10.5 10.5mm bore M20 x 1.5 3.5 5.01 H-KD-15.3 15.3mm bore M20 x 1.5 3.5 5.01 H-KD-M24- BLUE(RAL05) M24 x 1.5 M20 x 1.5 3.5 5.01 KSE 64 3 Ø 23 Ø 61.5 H-KSE 1/ BSP M16 x 1.5 3.75 4. H-KSE-14 1/4 BSP M16 x 1.5 3.75 4. H-KSE-12 1/2 BSP M16 x 1.5 3.75 4. H-KSE-M16 M16 x 1.5 M16 x 1.5 3.75 4. Ø 34 9 3 27mm MAXT Ø4. H-MA-XT M20 x 0.75 M16 x 1.5 3.00 3.90 52 29.5 Ø.2 20mm IP66 40 o C.5 30 MA Small Aluminium Head, M20 x 0.75 externally threaded process. MA Equivalent to MAA 52 29.5.5 Ø.2 Ø4. 20mm IP66 40 o C H-MA M10 x 1.0 M16 x 1.5 3.00 3.90 H-MA-1 1/ BSP M16 x 1.5 3.00 3.90 30 7 Temperature Technology Ltd.
Aluminium Heads KAA 20. 45 31 H-KAA H-G-M16 Description Aluminium Angled Entry Head M16 x M16 M16 cable gland with rubber bushing 3.0 4.94 1.00 1.30 Ø1.4 47 19mm 40 o C Supplied without cable gland and bush. TL Large version (PE - 1/2 BSP) 10 67 TL-2P-C Description TL Head with ceramic 2 way block 3. 4.55 Ø 30 Also available with Bakelite terminal block. TS Small version (PE - 1/4 BSP) 7 14 5 TS-2P-C Description TL Head with ceramic 2 way block 3.00 3.90 Ø 19 Also available with Bakelite terminal block. KNN Plastic Heads 7 Ø 2 H-KNN 1/2 BSP M20 x 1.5 3.75 4. H-KNN-M24 M24 x 1.5 M24 x 1.5 3.75 4. IP65 200 o C 13 46 Ø 3 Glass Filled Nylon. Temperature Technology Ltd.
Plastic Heads KPP (FDA Approval) Ø 2 7 H-KPP 1/2 BSP M20 x 1.5 4.30 5.59 H-KPP-NPT 1/2 NPT M20 x 1.5 4.30 5.59 IP6 165 o C 13 46 Ø 3 White Polyproplene. KPP-B (FDA Approval) 7 Ø 2 H-KPP-B 1/2 BSP M20 x 1.5 4.30 5.59 IP6 165 o C 13 46 Ø 3 Black Polypropylene. KB Ø 2 91.5 IP6 10 o C H-KB 1/2 BSP M20 x 1.5 6..45 13 46 Ø 3 Bakelite. KBS Ø 61.5 6 23 3 Ø H-KBS 1/4 BSP 3/ BSP 4. 5.5 27mm IP6 10 o C Ø 34 9 3 Bakelite. 9 Temperature Technology Ltd. Please Note: All list prices are subject to change. Check website www.temperaturetechnology.com for up to date information
Cast Iron Heads KI 95 56 Ø 37 Ø 6.5 H-KI 1/2 BSP M20 x 1.5 16.00 20.0 H-KI-34 3/4 BSP M20 x 1.5 16.00 20.0 H-KI-NPT 1/2 NPT M20 x 1.5 16.00 20.0 H-KI-M24 M24 x 1.5 M20 x 1.5 16.00 20.0 9 51 Ø 43 IP67 900-1000 o C CCI NEMA 4X Approval Ø6 7 4 Ø36 45mm IP6 900-1000 o C H-CCI 1/2 BSP M20 x 1.5 12.00 15.60 47 Stainless Steel 316 Heads CLS 39 Ø30 Ø54 77 H-CLS 1/2 BSP M20 x 1.5 30.00 39.00 45mm IP6 20 49 (34) Supplied without cable gland and bush. CSS NEMA 4X Certified Ø7.5 7 H-CSS 1/2 BSP M20 x 1.5 30.00 39.00 46 40mm 45mm 45 www.temperaturetechnology.com Temperature Technology Ltd. 10
Stainless Steel 316 Heads LS Ø2 H-LS 1/2 BSP M20 x 1.5 35.00 45. H-LS-M20 M20 x 1.5 M20 x 1.5 35.00 45. H-LS-M25 1/2 BSP M25 x 1.5 35.00 45. 7 49 H-LS-NPT 1/2 NPT M20 x 1.5 35.00 45. H-LS-NPT-NPT 1/2 NPT 1/2 NPT 35.00 45. Ø3 13 46.5 H-LS-34 1/2 BSP 3/4 BSP 35.00 45. IP6 SBUZ Ø4 H-SBUZ 1/2 BSP M20 x 1.5 30.00 39.00 3 Ø56 IP6 SBUZ-H 114 316L Ø76.2 H-316L 1/2 BSP M20 x 1.5 29.00 40.60 H-316L-NPT 1/2 NPT M20 x 1.5 29.00 40.60 54 Lever kit available 0.5 / 1.19 Ø4 Ø56 H-SBUZH 1/2 BSP M20 x 1.5 35.00 45. H-SBUZH-NPT 1/2 NPT M20 x 1.5 35.00 45. IP6 Lever kit available 0.5 / 1.19 3 4 IP6 1 Can house two transmitters/terminal blocks. 11 Temperature Technology Ltd. Please Note: All list prices are subject to change. Check website www.temperaturetechnology.com for up to date information
11 7.2 10 2-Ø4.4 THRU. Ø7.2x5H 20 23 A2 A1 B2 b2 B1 b1 11 20 7.2 10 23 A2 A1 B2 b2 B1 b1 11 20 7.2 10 23 A2 A1 B2 b2 B1 b1 11 20 7.2 10 23 Terminal Heads Stainless Steel 316 Heads KFS 42.5 14 Ø 2.5 Ø 34 H-KFS 1/2 BSP M20 x 1.5 35.00 45. 12.5 9.5 IP6 BLS 91 Ø6 H-BLS 1/2 BSP M20 x 1.5 40.00 52.00 H-BLS-M25 1/2 BSP M25 x 1.5 40.00 52.00 IP6 49 Supplied without cable gland and bush. SEG Equivalent to BEG 42.5 Ø5 Ø49.5 70.5 H-SEG M24 x 1.5 M20 x 1.5 22. 29.25 H-SEG-12 1/2 BSP 1/2 BSP 22. 29.25 H-SEG-12-M20 1/2 BSP M20 x 1.5 22. 29.25 Highly polished. SS Ø 61.5 70 3 Ø 23 Ø 34 9 3 Remember! 27mm IP65 1000-1100 o MC Type Block (Screw with clamp) C H-SS 1/4 BSP M16 x 1.5 22. 29.25 H-SS-12 Terminal 1/2 BSP Blocks M16 x 1.5 22. 29.25 M S e r i e s fixings to accompany Terminal Heads with this keycode. MC-2P-C MC-3P-C MC-4P-C MC-6P-C 2-Ø4.4 THRU. Ø7.2x5H Poles Material MC-2P-C 2 45% AI203 1. 1.95 MC-3P-C 3 45% AI203 1.90 2.47 MC-4P-C 4 45% AI203 2.25 2.92 MC-6P-C 6 45% AI203 3.10 4.03 2-Ø4.4 THRU. Ø7.2x5H 2-Ø4.4 THRU. Ø7.2x5H Check which Terminal Blocks suit which Heads by looking at the coloured dots. MD Type Block (Solder Lug) 2-Ø4.4 2-Ø4.4 2-Ø4.4 2-Ø4.4 fixings to accompany Terminal Heads with this keycode. Poles Material MD-2P-C 2 45% AI203 1.55 2.02 MD-3P-C 3 45% AI203 1.90 2.4 MD-4P-C 4 45% AI203 2.30 2.99 MD-6P-C 6 45% AI203 3.00 3.90 MD-2P-C MN Type Block (No through hole) MD-3P-C MD-4P-C MD-6P-C Temperature Technology Ltd. 12
Ex d Terminal Heads Component Certified, flameproof Ex d terminal heads. Available with ATEX and FM certification. Standards: ATEX 94/9/EC, EN 01, EN60079-1 US (NEC 0) FM3600, CSA C22.2 No. 0, FM3615, C22.2 No.30 XDS Stainless Steel. 111 C o n d u i t E n t r y 97.6 ATEX/FM approval PE CE XDS-A-12BSP-M20 ATEX ½ BSP M20x1.5 70.00 91.00 XDS-A-12NPT-12NPT ATEX ½ NPT ½ NPT 70.00 91.00 XDS-F-12NPT-12NPT FM ½ NPT ½ NPT 70.00 91.00 40mm IP6 P r o c e s s E n t r y Bush and flame path collar available upon request (see below). EC Certificate No. Rating: BSI 07 ATEX 153245U EEx d IIC T6 IP6 Ex td A21 T100 C IP6 FM Certificate: Rating: NEC 0 EXPLOSIONPROOF Class I, Division 1, Groups A, B, C, D, T6 Class I, Division 1, Groups E, F, G, T6 Class III, Type 4X XDA Aluminium, Epoxy paint RAL05. 111 C o n d u i t E n t r y 97.6 P r o c e s s E n t r y ATEX/FM approval PE CE XDA-A-12BSP-M20 ATEX ½ BSP M20x1.5 25.00 32. XDA-A-12NPT-12NPT ATEX ½ NPT ½ NPT 25.00 32. XDA-A-34BSP-M20 ATEX ¾ BSP M20x1.5 25.00 32. XDA-A-M24-M20 ATEX M24x1.5 M20x1.5 25.00 32. XDA-F-12NPT-12NPT FM ½ NPT ½ NPT 25.00 32. XDA-F-12NPT-34NPT FM ½ NPT ¾ NPT 25.00 32. 40mm IP6 40 o C Flamepath collar, 5.00/pc 6./pc, and Bush, 5.00/pc 6./pc. EC Certificate No. Rating: BSI 07 ATEX 153245U EEx d IIC T6 IP6 Ex td A21 T100 C IP6 FM Certificate: Rating: NEC 0 EXPLOSIONPROOF Class I, Division 1, Groups A, B, C, D, T6 Class I, Division 1, Groups E, F, G, T6 Class III, Type 4 Contact our Sales Team for assistance. Tel: +44(0)11 9730739 Fax: +44(0)11 9737222 We welcome your enquiries for any Head not listed. 13 Temperature Technology Ltd. Please Note: All list prices are subject to change. Check website www.temperaturetechnology.com for up to date information
Custom Heads Terminal Heads SS, Aluminium, CI, Plastics Heads Tailor made to suit specific requirements Various process and conduit entries available Colour painting to RAL no s Epoxy Coating Available New designs can be tooled from sample or drawing (subject to MOQ). TTL *Certification on all heads available upon request* T T L Company name molding available www.temperaturetechnology.com Temperature Technology Ltd. 14