1. Identification of the substance or preparation and of the company/undertaking. Identification of the Substance/Preparation: Product use:. Dealer: Espuma Jofel Industrial, s.a. Telephone number for emergency: 915 620 420 2. Hazards identification. Preparation not classified as dangerous according to Directive 1999/45/EC 3. Composition/information on ingredients. Information on hazardous components according to the Directive 67/548/EEC: Concentration range of the constituent (% weight/weight) CE Number CAS No. Chemical name 1% and <5% 271-657-0 68603-42-9 Amides, coco, N,Nbis(hydroxyethyl) Symbol(s). Risk Phrases Xi; R38-41 Full text of each relevant R phrase is listed under the heading 16. Detergent Labelling (648/2004/CE) Preservants: Contains: Content Constituents 5 % or over but less than 15 % Anionic tensioactives Perfumes less than 5 % Non-ionic tensioactives Amphoteric tensioactives The surfactants contained in this preparation do not comply with the biodegradability criteria 4. First aid measures. Consumption: Eye contact: Inhalation: Skin contact: If swallowed, rinse mouth with water. Seek medical advice immediately and show this container or label. Do NOT induce vomiting. First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then take to a doctor. If inhaled, remove person to fresh air. If not breathing give artificial respiration. If breathing is difficult, give oxygen. Obtain medical advice. Remove contaminated clothes. Rinse skin with plenty of water or shower. Refer for medical attention. Page:1/5
5. Fire-fighting measures. Extinguishing Media: Other Fire Fighting Considerations: Known or Anticipated Hazardous Products of Combustion: Special Fire Fighting Procedures: 6. Accidental release measures. Carbon dioxide, dry chemical powder or appropriate foam. For safety reasons do not use full water jet. Heating causes a rise in pressure, risk of bursting and explosion. Emits toxic fumes under fire conditions. Wear self-contained breathing apparatus and protective clothing to prevent contact with skin and eyes Procedures for Spill/Leak Clean-up: Personal Precautions: Environmental Precautions: Cover with an inert, inorganic, non-combustible absorbent material (e.g. drylime, sand, soda ash). Place in covered containers using non-sparking tools and transport outdoors. Avoid open flames or sources of ignition (e.g. pilot lights on gas hot water heater). Ventilate area and wash spill site after material pickup is complete. Dispose of in accordance with current laws and regulations. Avoid sources of ignition. Wear respirator, chemical safety goggles, rubber boots and heavy rubber gloves. Keep people away, evacuate area. To avoid possible contamination of the environment, Do not discharge into any drains, surface waters or groundwaters. 7. Handling and storage. Handling: Recommended Packing Materials: Storage: Usage Precautions: Product use: Keep away from food, drink and animal feedingstuffs. When using do not smoke. Avoid contact with skin and eyes. To be stored in tightly sealed and preferably full containers in cool, dry and ventilated area. Keep in glass, suitable plastic, aluminum or laquer-lined containers. Protect from heat/overheating and light sources. Keep material away from sources of ignition (e.g. hot surfaces, sparks, flame and static discharges. Smoking should not be permitted in work areas. 8. Exposure controls/personal protection. Eye/Face protection: Respiratory Protection: Chemical safety goggles are recommended. Wash contaminated goggles before reuse. Ventilation, local exhaust, or breathing protection. Page:2/5
Skin Protection: Hand Protection: Engineering Controls-Ventilation: Other Personal Protective Wear: Avoid contact with skin. Wear suitable gloves Compatible chemical-resistant gloves are recommended. Wash contaminated gloves before reuse. Mechanical exhaust required. In confined or poorly ventilated areas, the use of an appropriate respiratory protection may be required. Measures should be taken to prevent materials from being splashed into the eyes or on the skin. Wear eyeshields and protective clothing. Declaration of substances is not required. 9. Physical and chemical properties. Appearance: Boiling Point: - Color: Blue Density: 1 Flash Point: - Odour: - ph-value undiluted: 6-8 Solubility: Essentially soluble. 10. Stability and reactivity. Conditions to Avoid: Hazardous Decomposition Products: Incompatibility: Hazardous Polymerization: Avoid excessive heat, sparks or open flame. Carbon monoxide and other unidentified organic compounds may be formed upon combustion. None known No special precautions other than good houskeeping of chemicals. 11. Toxicological information. Toxicological effects: Substance No toxicological information is available on this preparation as such. Acute oral toxicity Acute dermal Acute Inhalation (LD50) toxicity (LD50) toxicity (LC50) 12. Ecological information. Ecotoxicity: Information not yet available. Further information: See also headings 6, 7, 13 and 15. Substance Do not allow the material to enter streams, sewers or other waterways. Acute aquatic Bioconcentration Biodegradation toxicity Factor Page:3/5
13. Disposal considerations. Container disposal: Disposal conditions: Don not re-use empty containers. Empty residue into application equipment. Dispose of in accordance with all federal, state and local environmental regulations. 14. Transport information. International Carriage of Dangerous Goods by Road (ADR) Not subject to ADR Label: - Sea Transport (IMDG) Label: Air Transport (ICAO/IATA) Label: Not restricted Not restricted 15. Regulatory information. Classification according to Directive 1999/45/EC Identification of the Substance/Preparation: Espuma Preparation not classified as dangerous according to Directive 1999/45/EC Safety Data Sheet available for professional users on request 16. Other information. Text of risk phrases associated with ingredients listed in section 3: R38: Irritating to skin R41: Risk of serious damage to eyes Page:4/5
This material should only be used for industrial purposes. Information in this MSDS is from available published sources and is believed to be accurate. No warranty, express or implied, is made and our company assumes no liability resulting from the use of this MSDS. The user must determine suitability of this information for his application Revision date:10-03-2009 Version: 1 Reason for Change: Page:5/5