CAPIOX SX Family of Oxygenators High-performance, Hollow Fiber Oxygenators with
Performance Data CAPIOX SX10 Hollow Fiber Oxygenator CAPIOX SX18 Hollow Fiber Oxygenator CAPIOX SX25 Hollow Fiber Oxygenator Holder Systems Catalog # XX*CXH18 Catalog # XX*CXH18R Catalog # XX*XH032
CAPIOX SX Family of Oxygenators Terumo s line of high-performance CAPIOX SX oxygenators are available in multiple sizes to accommodate every patient. Able to meet the requirements of small to large patients, this family of oxygenators offers low priming options and high gas exchange. Proven performance features, including Terumo s exclusive biopassive surface coating, make these highly efficient oxygenators the right choice for the perfusionist and the patient. Oxygenator Xcoating Surface Coating Terumo s exclusive hollow fiber technology is used in every CAPIOX SX oxygenator. This amphiphilic surface coating has both hydrophobic and hydrophilic properties which reduce platelet adhesion and minimize platelet activation. Unique fiber bundle design creates a uniform blood flow, resulting in consistently high gas exchange. Non-heparin based biopassive polymer does not react with blood components. Superior quality control assures consistent oxygenator performance. Adheres to all surfaces and has no contraindications for patient size. Reservoir Heat Exchanger Separate cardiotomy and venous filters improve handling of venous blood and minimize defoamer contact. Efficient heat exchange produced by hundreds of stainless steel pipes facilitates the uniform circulation of water through the heat exchanger compartment. Flat front enhances visibility and allows for easy mounting of level sensor pads. Tapered design aids low level volume assessment. Volume scales are easily visible on three sides, even at low volume levels. Short breakthrough time permits quick and easy priming. Integrated positive pressure relief for vacuum assisted venous drainage (SX18/SX25).* Detachable hardshell reservoir for additional setup options. Designed specifically to reduce cooling and rewarming times. Non-compliant heat exchanger design does not expand and contract, regardless of temperature and pressure changes.
CAPIOX SX10 Oxygenator Specially designed to meet the needs of smaller patients. Priming volume of 135 ml Blood flow rate of up to 4.0 L/min Reservoir capacity of 3,000 ml; 70 ml minimum operating level CAPIOX SX18 Oxygenator Compact oxygenator for a wide range of patient sizes. Priming volume of 270 ml Large blood flow rate of up to 7.0 L/min Large reservoir capacity of 4,000 ml; 200 ml minimum operating level
Clinical Education and Support Terumo Cardiovascular Group is a global leader in clinical education and support. Through programs like Terumo Academy and Optimizing Cardiac Surgery, Terumo helps to ensure that the highest standards of clinical care are delivered to patients worldwide. For information on training and education in your region, contact your local Terumo representative. CAPIOX SX25 Oxygenator Enhanced gas exchange performance for larger patients. Priming volume of 340 ml Large blood flow rate of up to 7.0 L/min Large reservoir capacity of 4,000 ml; 200 ml minimum operating level
CAPIOX SX Family of Oxygenators Specifications Oxygenator and Heat Exchanger MATERIAL Housing Polycarbonate Oxygenator fibers Heat exchanger Microporous polypropylene Stainless steel OXYGENATOR SX10 SX18 SX25 Fiber bundle surface area Approx. 1.0 m 2 Approx. 1.8 m 2 Approx. 2.5 m 2 Heat exchanger surface area Approx. 0.13 m 2 Approx. 0.22 m 2 Approx. 0.22 m 2 Blood flow range 0.5-4.0 L/min 0.5-7.0 L/min 0.5-7.0 L/min Priming volume (static) 135 ml 270 ml 340 ml Blood inlet port (from pump) 3/8 (9.5 mm) 3/8 (9.5 mm) 3/8 (9.5 mm) Blood outlet port 3/8 (9.5 mm) 3/8 (9.5 mm) 3/8 (9.5 mm) Cardioplegia port Gas inlet port Gas outlet port Water ports (base: 3/8 with gas vent) 1/2 (12.7 mm) Hansen quick connect fitting Maximum pressure blood inlet 1,000 mmhg (133 kpa) Ordering Information CATALOG # DESCRIPTION UNITS/CASE CAPIOX SX10 Oxygenator CX*SX10R Hollow fiber oxygenator with hardshell reservoir 4 CX*SX10RX Hollow fiber oxygenator with hardshell reservoir with 4 Xcoating surface coating CAPIOX SX18 Oxygenator CX*SX18R Hollow fiber oxygenator with hardshell reservoir 4 CX*SX18RX Hollow fiber oxygenator with hardshell reservoir with 4 Xcoating surface coating CAPIOX SX25 Oxygenator CX*SX25R Hollow fiber oxygenator with hardshell reservoir 4 CX*SX25RX Hollow fiber oxygenator with hardshell reservoir with 4 Xcoating surface coating Holders for CAPIOX SX Oxygenator XX*CXH18 Holder for SX oxygenator 1 XX*CXH18R Holder for SX/RX/FX oxygenator with hardshell reservoir (except U.S.) 1 XX*XH032 Holder for hardshell reservoir, short arm (except U.S.) 1 Accessories for CAPIOX SX Oxygenators 1CX*BP021 Blue thermistor wire 10 1CX*BP022 Red thermistor wire 10 Hardshell Reservoir MATERIAL Housing Polycarbonate Venous filter Polyester screen type, pore size 47 µm Cardiotomy filter Defoamer Polyester depth type Polyurethane foam OXYGENATOR SX10 SX18 SX25 Blood flow range Venous flow 0.5-4.0 L/min 0.5-7.0 L/min 0.5-7.0 L/min Cardiotomy inlet Max. 4.0 L/min Max. 5.0 L/min Max. 5.0 L/min Combined flow Max. 4.0 L/min Max. 7.0 L/min Max. 7.0 L/min Blood storage capacity 3,000 ml 4,000 ml 4,000 ml Minimum operating volume 70 ml 200 ml 200 ml Venous blood inlet port 3/8 (9.5 mm) 1/2 (12.7 mm) 1/2 (12.7 mm) Rotatable Rotatable Rotatable Blood outlet port (to pump) 3/8 (9.5 mm) 3/8 (9.5 mm) 3/8 (9.5 mm) Rotatable Suction ports Vertical port to CR filter Quick prime port Vent port Auxiliary port Luer ports Maximum sustainable negative pressure Six 3/8 (9.5 mm) 1/4-3/8 (6.4 mm - 9.5 mm) Four filtered luer ports to cardiotomy filter One non-filtered luer port Two luer ports on venous inlet -150 mmhg (-20 kpa) Positive pressure relief valve N/A 0-8 mmhg 0-8 mmhg (1.1 kpa)* (1.1 kpa)* The photographed products featured throughout this brochure were manufactured in Terumo Cardiovascular Group s Elkton, Maryland, and Ashitaka, Japan, factories. Depending on the factory, CAPIOX SX oxygenators will exhibit slight physical design differences, including cap and label colors and shapes, method of positive pressure relief valve integration, venous inlet sampling port location, and CR filter material. Not available in Europe and the U.S. Not available in Europe. Replaced with catalog number XX*CXH25F. * Only for products manufactured in Elkton, Maryland. For information on Terumo Cardiovascular Group products: Terumo Cardiovascular Group 6200 Jackson Road Ann Arbor, MI 48103-9300 USA Tel: +1.734.663.4145 Fax: +1.734.663.7981 www.terumo-cvgroup.com Terumo Corporation 44-1, 2-chome, Hatagaya Shibuya-Ku, Tokyo 151-0072 Japan Tel: +81.3.3374.8111 Fax: +81.3.3374.8399 www.terumo.co.jp Terumo Europe N.V. Authorized EC Representative Interleuvenlaan 40, 3001 Leuven Belgium Tel: +32.16.38.12.11 Fax: +32.16.40.02.49 www.terumo-europe.com Terumo Europe N.V. Cardiovascular Division Ludwig-Erhard-Strasse 6 65760 Eschborn Germany Tel: +49.6196.8023.0 Fax: +49.6196.8023.555 Terumo Latin America Corporation 8750 NW 36th Street, Suite 600 Miami, FL 33178 USA Tel: +1.305.477.4822 Fax: +1.305.477.4872 Terumo Corporation Dubai Branch Al Masraf Tower, 22nd Floor P.O. Box 20291, Dubai UAE Tel: +971.4.2212220 Fax: +971.4.2213330 Terumo India Pvt. Ltd. Unit No. 1601 & 1602 Tower B 16th Floor, Unitech Cyber Park Sector-39 Gurgaon, Haryana 122001 India Tel: +91.124.4718700 Fax: +91.124.4718718 Terumo Asia Holdings Pte. Ltd. 300 Beach Road #33-03 The Concourse 199555 Singapore Tel: +65.6.295.1792 Fax: +65.6.294.2329 Terumo and CAPIOX are registered trademarks and Xcoating is a trademark of Terumo Corporation. Optimizing Cardiac Surgery is a registered trademark and the Terumo Academy logo is a trademark of Terumo Cardiovascular Systems Corporation. Terumo Cardiovascular Systems Corporation. June 2015. 862467