FOOSBALL ASSEMBLY, INSTRUCTIONS AND RULES 56007 PL Waterloo Valley Road / Mt. Olive, NJ 07828 / www.sportcraft.com / (800) 526-0244 / Fax: (97) 47-54
MODEL # 56007 PL Congratulations on owning a new KT Sports Foosball game! We at KT Sports hope you will have many hours of enjoyable use with this product.! WARNING: Choking Hazard -- Table contains small balls and/ or small parts. Not for children under years. IMPORTANT! Please Keep Your Instructions in the storage pouch provided underneath your table! Your Model number (also located on the underside of the table) is necessary should you need to contact us. Before attempting assembly, please read through this instruction book to familiarize yourself with all the parts and assembly steps. We recommend that two adults assemble this game. Please refer to the Parts Identifier below and be sure that all parts have been included. Although we at KT Sports are dedicated to giving our customers the best product possible, occasionally a part may be missing. If you are missing a part, or if you have any questions, please call our Consumer Service Department at -800-526-0244 between the hours of 9:00 a.m. and 5:00 p.m. E.S.T. Do not return the game to the store. Please contact us first at -800-526-0244, or fax your request to us at: -97-47-54. TOOLS REQUIRED FOR ASSEMBLY: Phillips and Slotted Head Screwdrivers (or Power Driver) - not included Allen Key- included 2 4 5 6 SIDE APRON END APRON GOAL END BOARD ASSEMBLY PLAYFIELD - BLACK 56007PL0 (2) 56007PL02 (2) 56007PL0 (2) 56007PL04 () 56007PL05 (4) 7 8 9 0 LEGS - METAL F-CHANNEL - WHITE BEARING BUSHING - OUTER BALL BEARING BUSHING - INNER X-MEN (PLATED SLIVER) 56007PL06 (2) 5062PL07 (6) 5062PL08 (6) 56007PL07 () 56007PL08 () 2 4 5 X-MEN (PLATED GOLD) 2 PLAYER ROD ASSEMBLY - PLATED SLIVER B PLAYER ROD ASSEMBLY PLAYER ROD ASSEMBLY 5 PLAYER ROD ASSEMBLY 2 PLAYER ROD ASSEMBLY - PLATED SLIVER A GOALIE - PLATED SLIVER F - PLATED SLIVER D - PLATED GOLD G 56007PL09 () 56007PL0 () 56007PL () 56007PL2 () 56007PL () 0704 - C -
6 (ASSEMBLED) 7 8 9 20 (ASSEMBLED) (ASSEMBLED) PLAYER ROD ASSEMBLY PLAYER ROD ASSEMBLY 5 PLAYER ROD ASSEMBLY 2 HOLE 6MM HOLLOW HOLE 6MM HOLLOW - PLATED GOLD C - PLATED GOLD - PLATED GOLD "E" PLAYER ROD PLAYER ROD H GOALIE 56007PL4 () 56007PL5 () 56007PL6 () 5049DP09 (2) 5049DP0 (2) 2 22 2 24 25 HOLE 6MM HOLLOW GOALIE ROD 5 HOLE 6MM HOLLOW PLAYER ROD PLASTIC WASHER METAL WASHER END CAP - GREY 26 56007PL24 (2) 5049DP (2) 2709DP2 (6) 2709DP22 (6) 56007PL7 (8) 27 28 29 0 RUBBER BUMPER BALL ENTRY CUP - GREY BALL CATCHER BALL BOX 5600DP2 (6) 56007PL8 (2) 602PL22 (2) 5049DP7 (2) 5049DP6 (2) 2 4 5 (PRE-INSTALLED) BALL RETURN CHANNEL METAL SUPPORT BRACE BALL RETURN COVER GOAL BOX - GREY SOCCER BALL - WHITE SOCCER BALL - ORANGE 602PL29 (2) 56007PL9 (2) 56007PL2 (2) 5600DP25 (2) 5600DP24 (2) 6 7 8 9 40 (PRE-INSTALLED) PLASTIC BEAD SCORER - PLATED SLIVER PLASTIC BEAD SCORER - PLATED GOLD HAND GRIP - BLACK WITH SLIVER INSERT 6" BELL STYLE LEG LEVELER NAME PLATE 4 56007PL20 () 56007PL2 () 609DP (8) 50DP09 (4) 5600DP2 (2) 42 4 44 45 PLAYER MOUNTING BOLT PLAYER NUT 8 X 5MM ALLEN KEY BOLT 8 X 8 MM ALLEN KEY BOLT 4 X 0MM ALLEN KEY BOLT 606DP5 (26) 606DP6 (26) 56007PL22 (6) 609DP2 (4) 5049DP (4) 47 48 49 50 5 22MM WASHER.5 X 28MM WASHER 5067DP2 (20) 60DP09 (4) 56002DP26 (2) 6065DP26 (4) 52 5.5 X 2MM WASHER.5 X MM FLAT.5 X 2MM FLAT 4048DP0 (4) + 96 (PRE-INSTALLED) SILICONE www.sportcraft.com.5 X 0.5MM FLAT 5MM ALLEN KEY SILICONE 5600DP2 (4) 4097DP0 () 5086PL20 () - 2
ASSEMBLY INSTRUCTIONS: We recommend that two adults work together to assemble this game. ) Open the carton of your new Foosball Game near where you will play. Select a clear level floor. The table will be assembled upside down and then turned over onto its legs. This is a very heavy game and turning it over will require at least Two Strong Adults. 2) Remove all the contents from inside the carton and verify that you have all listed parts as shown on the Parts Identifier. NOTE: Some parts are pre-installed and the player rods are pre-assembled. We suggest that you use the bottom carton as a clean flat work area to protect the game. Carefully cut or tear the four carton corners so that the bottom is now your work area. FIG. ) Place one Side Apron (#) with the top edge down and finished surface facing outward. Slide the Player Rods (#A through #H) through the Player Rod Bushing (#8) in order shown in Fig.. NOTE: The Player Rods have a letter on the end where the Hand Grips go. Make sure that the Player Rods are installed properly. The players should be upside down with their backs facing their own goal. (The BACK of the X-Men player has a star-shaped cut-out.) The player for each team must be facing the same direction. SLIVER SLIVER D SLIVER B F 6 0 26 IMPORTANT! EACH TEAM SHOULD BE HEAD DOWN AND FACING THEIR OPPONENT S GOAL BOX. A SLIVER FIG. 2 8 9 24 2 C E G H FIG. 4) Attach the Goal Boxes (#) onto each Goal End Board Assembly (#) using two Screws (#5) as shown in Fig. 2A. 5) Attach the Goal End Board Assembly (#), with the finished surface facing down into the slot of the Side Aprons as shown in Fig. 2. NOTE: This is a groove on the Side Apron. Make sure to #5 =.5 x 0.5MM FLAT attach the Goal End Board into the groove. Do the same for the Goal End Board FIG. 2 Assembly at the other end. 6) Now attach the other Side Apron (#). With the finished edge facing down and finished surface facing outward, slide the other end of the Player Rods (#A through #H) through the Ball Bearing Bushings (#8). GOLD GOLD GOLD GOLD 5 FIG. 2A -
FIG. 7) Now attach the End Apron (#2) to the Goal End Board Assembly (#) using two Screws (#47) as shown in Fig. A. 8) Attach two Legs (#5) to the table using four Bolts (#4) and four Washers (#) per Leg and secure it using the Allen Key (#28) provided as shown in Fig. B. 9) Slide the Playfield (#4), with the graphics facing down, into the F-Channel (#6). NOTE: Be sure that the Side Aprons are square and the Playfield is in the grooves of the F-Channel. Secure the Playfield (#4) with four Bolts (#45) using the Allen Key (#52) as shown in Fig.. NOTE: The Bolts go through the Playfield and then through the Goal End Boards. 0) Repeat step 7 to attach the other End Apron (#2). NOTE: Be sure that the Side Aprons and End Aprons are square. ) Repeat step 8 to attach the other two legs. #4 = 8 X 5MM ALLEN KEY BOLT # = 22MM FLAT WASHER #45 = 4 X 0MM ALLEN KEY BOLT #47 =.5 x 28MM WASHER FIG. B 52 52 5 4 47 45 4 47 2 5 2 FIG. 4 FIG. 2 FIG. A 2) Place the Metal Support Braces (#) on the Playfield (#4), secure them using two Screws (#50) into the Playfield and two Bolts (#44) and two Washers (#) into the Side Apron with the Allen Key (#52) provided per Metal Support Brace. See Fig. 4 and 4A. ) Screw the four Leg Levelers (#9) into each leg. NOTE: Leg Levelers are optional, and if the game is to be used on a smooth floor, we recommend not installing them. 9 FIG. 4 #44 = 8 X 8MM ALLEN KEY BOLT # = 22MM FLAT WASHER 50 50 #50 =.5 X 2MM FLAT FIG. 4A 44 44-4
FIG. 5 4) Attach two Ball Catchers (#28) to the End Apron (#2) using two Screws (#48) per Ball Catcher as shown in Fig. 5. Then attach the Ball Box (#29) to the Side Apron (#) using four Screws (#48) per goal boxes. NOTE: Pilot holes show the proper screw placement. 5) Insert the Ball Return Channels (#0) between the Ball Catchers and the Ball Boxes. See Fig. 5A. 6) Lift the table assembly from the floor with two strong adults, turn it over, and set the table on its legs in the location where you will play. CAUTION: DO NOT LIFT, CARRY OR TURN THE TABLE OVER USING THE RODS AS THIS MAY DAMAGE THEM. Now go back and make sure all connections are tight. #48 =.5 X 2MM WASHER FIG. 5 48 28 0 48 29 0 28 29 FIG. 5A CAUTION: Two strong adults are recommended to turn the table over as shown.. Lift the table off the ground. 2. Turn the table over.. Place it on all four feet at the same time on the ground. HOLD TABLE CABINET HOLD THE DO NOT LEGS DO NOT LEAN THE TABLE ON ITS LEGS! FIG. 6 7) Attach the Plated Sliver Bead Scorer (#6) at the top of the Goal End Board (#) using two Screws (#49) as shown in Fig.6. Pilot holes show the proper screw placement. Do the same for the Plated Gold Bead Scorer (#7) at the other end of Goal End Board (#). 8 FIG. 6 49 7 8) Put the eight Hand Grips (#8) and End Caps (#25) on the rod ends in order as shown in Fig. 6. The Hand Grips go on the ends of the rods with holes in them. NOTE: To make the Hand Grips easier to attach, spray a little window cleaner on the rod ends prior to installation and gently tap on them with a hammer. 9) Install the back half of one Ball Entry Cup (#27) from the inside of the Side Apron (#) and install the front half of the Ball Entry Cup from the outside of the Side Apron and twist both halves together. See Fig. 6A. 6 25 27 FIG. 6A #49 =.5 X MM FLAT - 5
GAME RULES:. To start play, flip a coin to see which team or player will serve first. To begin, serve the ball through the side entry cup. 2. Press and score by pushing and pulling rods and twisting grips. Spinning the rods is considered illegal in tournament play. If playing as teams (more than two players total), once the ball is served, players may not change position on the rods until: one team scores; a team requests a time out (maximum 2 per game); the ball must be served again; or between games.. A point is scored when the ball enters the goal. A serve, by the team last scored upon, follows each goal. Teams change table sides after each game. 4. Intentional jarring or tipping of table during play is illegal, and reaching into the playing area during play is illegal (except for a dead ball). 5. A ball is considered a DEAD BALL when it has completely stopped its motion or is unreachable by any player. If a ball stops between the goal and the two-man rod, then it is put back into play by placing it in the corner that is nearest the dead ball spot. If the ball completely stops anywhere else on the playfield between both two-man rods, it is put back into play with a serve by the team which originally served the ball. 6. If a ball leaves the playing area during play (other than through the goals), the ball is considered OUT OF PLAY. The ball is returned to play with a serve by the team which originally served the ball. 7. This game is meant to be played with either two or four players. We recommend that all others should stand clear of the table playing area if they are not playing. TABLE MAINTENANCE:. TABLE: Keep your table covered. If there is dust on the playfield or the aprons, use a vacuum or wipe with a clean, soft cloth to remove. Do not sit on the table and do not use the table outside. 2. RODS: Make sure that the bolts and screws on the players are tight. Occasionally wipe the rods with a clean, soft cloth. Never lift the table by the rods. Do not spin the rods too aggresively, as this may cause damage. We recommend the use 00 % silicone to lubricate the bushings, from the outside of the game so as not to drip onto the playfield.. LEGS: Check that the leg bolts are tight. When moving the table, lift the table off of its legs and place it down squarely on the legs, do not drag the table (and do not lift by the rods). Mt. Olive, NJ 07828 Printed in China - 6
LIMITED WARRANTY Limited Warranty Sportcraft, Ltd. (the Company ) warrants the Product to be free from defects in workmanship and materials under normal use and conditions FOR A PERIOD OF ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE in the United States and Canada. Product Registration Card The Product Registration Card must be filled out completely and mailed to the Company at the address printed on the card within 0 days from the date of your purchase of the Product. What Is Covered Except as provided below, this Limited Warranty covers all defects in materials and workmanship. This Limited Warranty is void if the Product is: Damaged through improper usage, negligence, misuse, abuse, transportation damage, acts of nature, or accident (including failure to follow the instructions supplied with the Product) Used in commercial applications or rentals Modified or repaired by anyone not authorized by the Company. What Is Not Covered This Limited Warranty does not cover expendable items such as batteries, light bulbs, fuses, accessories, cosmetic parts and other items that wear out due to normal usage. What The Company Will Pay For If during the one year Limited Warranty period, any part or component of the Product is found by the Company to be defective, the Company will, at its option, reapire the Product, replace the Product with a new Product (either the same or an equivalent model) or cause the original retailer of the Product to exchange the Product with a new Product (either the same or an equivalent model) or refund the original purchase price of the Product, without charge for labor or parts. The Company s obligation to repair, replace or exchange the Product, however, shall be limited to the amount of the original purchase price of the Product. How To Obtain Warranty Service In order to enforce your rights under this Limited Warranty, you must follow these procedures: You must have completed and mailed the Product Registration Card to the Company within 0 days of purchase of the Product. You must include THE ORIGINAL COPY OF YOUR SALES RECEIPT. You must call the Company s Consumer Service Department at -800-526-0244 from 9:00 A.M. to 5:00 P.M. (EST) to notify the Company of the nature of the problem and to obtain instructions for how to obtain servicing. At the Company s option, the Product may be serviced at your location or at a location designated by the Company. If you are instructed to return the Product to the Company for servicing, you are responsible for shipping the Product, at your expense, to the address designated by the Company in packaging that will protect against further damage. You must also include your name, address, daytime telephone number, model number of the Product and a description of the problem. The Company will pay for any shipping charges to return the repaired or replaced Product to you. THIS LIMITED WARRANTY IS AVAILABLE ONLY TO THE ORIGINAL PURCHASER OF THE PRODUCT AND IS VALID IN THE UNITED STATES AND CANADA ONLY. THE COMPANY S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT ITS OPTION, OF ANY DEFECTIVE PRODUCT AND SHALL NOT INCLUDE ANY LIABILITY FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR DO NOT ALLOW FOR EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. TO THAT EXTENT, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights, but you may also have other rights that vary from state to state. If you have questions regarding this Limited Warranty or the operation of the Product, you may call or write us: Consumer Service Department Waterloo Valley Rd. Mt. Olive, NJ 07828-800-526-0244 0504 TG **NOTE: Please save your original proof of purchase as it is needed should you require warranty service. - 7
PARTS RE-ORDER FORM # 56007 PL - FOOSBALL REF 2 4 5 6 7 8 9 0 2 4 5 6 7 8 9 20 2 22 2 24 25 26 27 28 29 0 2 4 5 6 7 8 9 40 4 42 4 44 45 47 48 49 50 5 52 5 QUANTITY ORDERED PART # DESCRIPTION 56007PL0 56007PL02 56007PL0 56007PL04 56007PL05 56007PL06 5062PL07 5062PL08 56007PL07 56007PL08 56007PL09 56007PL0 56007PL 56007PL2 56007PL 56007PL4 56007PL5 56007PL6 5049DP09 5049DP0 56007PL24 5049DP 2709DP2 2709DP22 56007PL7 5600DP2 56007PL8 602PL22 5049DP7 5049DP6 602PL29 56007PL9 56007PL2 5600DP25 5600DP24 56007PL20 56007PL2 609DP 50DP09 5600DP2 606DP5 606DP6 56007PL22 609DP2 5049DP 5067DP2 60DP09 56002DP26 6065DP26 4048DP0 5600DP2 4097DP0 5086PL20 Side Apron End Apron Goal End Board Assembly Playfield Leg - Metal F-Channel - White Bearing Bushing - Outer Ball Bearing Bushing - Inner X-Men (Plated Sliver) X-Men (Plated Gold) 2 Player Rod Assembly - Plated Sliver Player Rod Assembly - Plated Sliver (Goalie) Player Rod Assembly - Plated Sliver 5 Player Rod Assembly - Plated Sliver 2 Player Rod Assembly - Plated Gold Player Rod Assembly - Plated Gold (Goalie) Player Rod Assembly - Plated Gold 5 Player Rod Assembly - Plated Gold 2 Hole Hollow Player Rod Hole Hollow Player Rod Hole Hollow Goalie Player Rod 5 Hole Hollow Player Rod Plastic Washer Metal Washer End Cap - Grey Rubber Bumper Ball Entry Cup Ball Catcher Ball Box Ball Return Channel Metal Support Brace Ball Retrun Cover Goal Box Soocer Ball - White Soccer Ball - Orange Plastic Bead Scorer - Plated Sliver Plastic Bead Scorer - Plated Gold Hand Grip 6 Leg Leveler Name Plate Player Mounting Bolt Player Nut 8 x 5mm Allen Key Bolt 8 x 8 mm Allen Key Bolt 4 x 0mm Allen Key Bolt 22mm Washer.5 x 28mm Washer Head Screw.5 x 2mm Washer Head Screw.5 x mm Flat Head Screw.5 x 2mm Flat Head Screw.5 x 0.5mm Flat Head Screw 5mm Allen Key Silicone 0000HG05 0000HG06 Optional Accessories: Table Cover Table Cover w/ Kit (extra balls and silicone) Send this form along with your check or money order payable to: Sportcessories Waterloo Valley Road Mt. Olive, NJ 07828 NAME: DATE: ADDRESS: PHONE: CITY: STATE: ZIP CODE: UNIT PRICE.00 ea 8.00 ea 7.00 ea 0.00 ea.00 ea.00 ea 4.00 ea.00 ea.00 ea 4.00 ea.00 ea 4.00 ea 4.00 ea.00 ea.00 ea 8.00 ea 25.00 ea 0.00 ea TOTAL AMOUNT 0704 - D Subtotal: NJ (6%) and IL (6.25%), and CA (7.75%) Residents Add State Sales Tax: Shipping and Handling Charges: TOTAL: **NOTE: PRICES IN US DOLLARS AND SUBJECT TO CHANGE WITHOUT NOTICE. $ 6.00 US