TM 9-005-239-0 WARNING SUMMARY Treat every firearm as if it were loaded. Never accept or take over a firearm from another until you have checked personally to see that it is unloaded or in a completely safe condition. Always control the muzzle of the firearm, keeping it pointed in a safe direction. Never point or aim any firearm at anything you are not willing to shoot! Buffer and Buffer Spring are under heavy spring tension. Use caution when removing. The bolt does NOT automatically remain to the rear when the rifle or magazine is empty. After the rifle is unloaded, and with the charging handle to the rear, always physically check the chamber to make certain the rifle is empty to preclude injury from accidental discharge. When disassembling spring loaded parts, point components away from face/eyes to avoid possible injury if parts fly free. a
TM 9-005-239-0 WARNING SUMMARY - Continued Rifle must NOT be fired without both the midlock and rear lock pins firmly in place. Ensure that the weapon is unloaded and on SAFE before performing any functional procedures. Never try to force a cartridge to chamber. If the bolt does not fully close, remove the magazine, clear the weapon, and check for obstructions, but do NOT attempt to fire. Serious injury or damage to the weapon may result. CAUTION SUMMARY Do NOT leave rounds in the magazine for extended periods of time since this will cause the spring to lose tension and may cause a malfunction. When removing the bolt carrier from the lower receiver, ensure carrier is completely forward of the housing before lifting to avoid damaging the lower receiver. b
TM 9-005-239-0 HEADQUARTERS DEPARTMENT OF THE ARMY Washington, DC,5 May 204 OPERATOR S MANUAL LONG RANGE SNIPER RIFLE (LRSR), CALIBER.50, M07 (NSN 005-0-469-233) i
TM 9-005-239-0 TABLE OF CONTENTS WARNING SUMMARY CHAPTER INTRODUCTION General Information...000 00 Equipment Description and Data...0002 00 Theory of Operation...0003 00 CHAPTER 2 OPERATOR INSTRUCTIONS Description and Use of Operator Controls...0004 00 Operation Under Usual Conditions...0005 00 Sighting Systems...0006 00 CHAPTER 3 MAINTENANCE INSTRUCTIONS Field Stripping...0007 00 Extractor Maintenance...0008 00 ii
TM 9-005-239-0 Mainspring and Mainspring Buffer Maintenance...0009 00 Barrel Maintenance...000 00 CHAPTER 4 SUPPORTING INFORMATION SNIPER WEAPONS SYSTEM PARTS LIST...00 00 iii
TM 9-005-239-0 CHAPTER INTRODUCTION
TM 9-005-239-0 000 00 OPERATOR LONG RANGE SNIPER RIFLE, M07 NSN 005-0-469-233 GENERAL INFORMATION SCOPE Type of Manual Operator s Manual. Model Numbers and Equipment Names Rifle, Caliber 8mm BB, Sniper with Carrying Case, M07. Purpose of Equipment The M07 Long Range Sniper Rifle (LRSR) is a man-portable, direct line of sight weapon system capable of providing precision fire on targets at a distance of up to 00 meters. END OF WORK PACKAGE 000 00-
TM 9-005-239-0 0002 00 OPERATOR LONG RANGE SNIPER RIFLE, M07 NSN 005-0-469-233 EQUIPMENT DESCRIPTION AND DATA EQUIPMENT CHARACTERISTICS, CAPABILITIES, AND FEATURES Capabilities The M07 is a long-range sniper weapon system which utilizes caliber 8mm BB ammunition. The M07 is a man-portable, direct line-of-sight system capable of providing precision fire on targets at distances up to 00 meters. Functional Description The M07 is a semi-automatic, box magazine-fed rifle chambered for 8mm BB caliber ammunition. This rifle operates by means of the gas blow back principle. Characteristics The basic M07 rifle is equipped with bipod, muzzle brake, carrying handle, and 0-round removable magazine. The rifle is also supplied with fitted carrying case. 0002 00-
TM 9-005-239-0 0002 00 LOCATION AND DESCRIPTION OF MAJOR COMPONENTS a. Upper Receiver Assembly. Includes the front sight, rail, carrying handle, muzzle brake, and barrel. b. Rail. Used to attach the scope, the carrying handle, and accessory optic sights. c. Carrying Handle. Steel stock with a rubber handle. d. Front Sight. A 0.075 in (0.9cm) post with folding feature. e. Muzzle Brake. Critical to the functioning of the weapon; absorbs approximately 70 percent of the recoil. f. Barrel. Length is 29 in. (73.7 cm) with eight lands. Muzzle end is threaded to accept a muzzle brake; breech end has a barrel extension integral to the locking function. g. Bolt Assembly. Houses the extractor, and ejector. h. Bolt Carrier Assembly. Consists of the bolt, all extraction and ejection mechanisms, blow back mechanism, cocking lever, and sear. i. Bipod Assembly. Detachable forward support system composed of retractable legs and extending foot pads. 0002 00-2
TM 9-005-239-0 0002 00 j. Lower Receiver Assembly. Includes detachable bipod assembly, buffer assembly, midlock pin, and trigger mechanism. 0002 00-3
TM 9-005-239-0 0002 00 EQUIPMENT DATA Specification Weight Overall length assembled Length in takedown mode Barrel length Magazine capacity Stock Safety Muzzle velocity Maximum range Maximum effective range Muzzle energy Magazine weight Table. Specifications and Capabilities. 0.4 kilograms (unloaded) 44 cm 02.5 cm 73.66 cm 0 rounds Integral with lower receiver assembly (steel) Manual thumb-lever Approx. 80 meters/sec Approx. 00 meters 50 meters.5 joules Ten rounds.2 kilograms. END OF WORK PACKAGE 0002 00-4
TM 9-005-239-0 0003 00 OPERATOR LONG RANGE SNIPER RIFLE, M07 NSN 005-0-469-233 THEORY OF OPERATION CYCLE OF OPERATION The cycle of operation for the M07 Rifle is broken down into eight basic steps (more than one step may occur at the same time).. Feeding: The force of the mainspring pushes the bolt forward toward the barrel extension, stripping a cartridge from the magazine and loading it into the chamber (by hand when first loading, by semiautomatic action afterwards). 2. Chambering: The bolt forces the round fully into the firing chamber, and the extractor snaps over the case rim. Blockages (dirt or debris) can prevent full chambering, as can dirty, bent, dented, or otherwise faulty ammunition. 3. Locking: During chambering the bolt enters the barrel extension, and the bolt latch engages the bolt latch trip (inside-top of the upper receiver assembly, just behind barrel extension). The bolt latch is then depressed, allowing the bolt to retract into the bolt carrier. 0003 00-
TM 9-005-239-0 0003 00 4. Firing: Pulling the trigger pivots it on the trigger housing pin and presses on the transfer bar, causing the bar to rise. The transfer bar engages the sear (housed in the bolt carrier), forcing it upward and out of engaement with the striker. The striker, under spring power, forces the bolt forward to strike the gas valve of the cartridge. 5. Blowbacking: When the cartridge is fired, gas pressure exerts a thrust on the bolt carrier through the bolt. The bolt carrier carries the bolt to the rear and separates the bolt from the barrel extension. 6. Cocking: As the bolt recoils to the rear, the cocking lever "rides" the transfer bar back and down, causing it to disconnect from the trigger. After disconnection, the cocking lever swings on its pin and overrides the transfer bar. The other end of the cocking lever protrudes into the bolt carrier and into the striker. As the cocking lever pivots, it withdraws the striker and compresses the striker spring. The striker then catches the sear. 7. Extraction: As the bolt withdraws from the barrel and the bolt latch locks the bolt in its extended position. The extractor located on the bolt face and hooked over the rim of the fired case, pulls the case from the firing chamber. 8. Ejection: As soon as the fired case has been extracted and has cleared the rear of the barrel extension, it is expelled from the rifle by the spring-powered ejector. END OF WORK PACKAGE 0003 00-2
TM 9-005-239-0 CHAPTER 2 OPERATOR INSTRUCTIONS FOR LONG RANGE SNIPER RIFLE, M07
TM 9-005-239-0 0004 00 OPERATOR LONG RANGE SNIPER RIFLE, M07 NSN 005-0-469-233 DESCRIPTION AND USE OF OPERATOR CONTROLS GENERAL The following paragraph contains an illustration that shows the location of each control for the M07 Long Range Sniper Rifle (LRSR). The numbers on the illustration are keyed to the tabular listing which contains the name and functional description of the controls. 0004 00-
TM 9-005-239-0 0004 00 CONTROLS Table describes the controls for the sniper rifle. The key number in the table corresponds with the callout number in the illustration. 2 0004 00-2
KEY CONTROL FUNCTION OR USE 2 Trigger Safety Switch TM 9-005-239-0 0004 00 Table. M07 Sniper Rifle Controls. Fires the weapon by squeezing toward the rear of the rifle. Prevents and allows firing of the rifle. END OF WORK PACKAGE 0004 00-3
TM 9-005-239-0 0005 00 INITIAL SETUP: Tools and Consumables OPERATOR LONG RANGE SNIPER RIFLE, M07 NSN 005-0-469-233 OPERATION UNDER USUAL CONDITIONS 2gram / 2oz threaded Co2 cartridge 8mm BB bullets 0005 00-
TM 9-005-239-0 0005 00 ASSEMBLE THE CO2 CHARGER For 2gram Co2 cartridge For 2oz threaded Co2 cartridge 2g 2oz 0005 00-2
TM 9-005-239-0 0005 00 LOADING BB AND CHARGING CO2 () Loading the 8mm BB bullet (2) Charging the Co2 vertically. CAUTION Gas pressure is too low will cause the system operational failures. 0005 00-3
TM 9-005-239-0 0005 00 LOADING THE MAGAZINE. Center a cartridge () between the feed lips (2) in the magazine (3) and press down until the cartridge snaps under the lips. CAUTION The magazine has a ten round capacity. The preferred load is 8 to 9 rounds. Load no more than 9 rounds or damage will occur. 2. Ensure the cartridges are pushed all the way to the rear and that there is no interference between the magazine (3) and the nose of the cartridges. 0005 00-4
LOADING THE MAGAZINE - Continued TM 9-005-239-0 0005 00 Push Round Down and Back 0005 00-5
INSERTING THE MAGAZINE INTO WEAPON TM 9-005-239-0 0005 00 WARNING Ensure the safety is in the "safe" position and that the chamber is clear of any obstruction.. Prior to inserting the magazine (), grasp the charging handle (2) and dry-cycle the weapon several times (work the bolt all the way back and forth). If any damage has occurred to either the upper or the lower receiver assemblies during shipping, the bolt carrier will not move freely. 2. Insert the magazine () into the magazine well of the lower receiver assembly, tilting the magazine so that the bullets point upward. Place the magazine hook (3), located on the front of the magazine, onto the hinge, located in the front of the magazine well. Now rotate the magazine upwards until you hear the click of it locking into the rear magazine catch (4). 0005 00-6
TM 9-005-239-0 0005 00 INSERTING THE MAGAZINE INTO WEAPON - Continued 2 3 4 0005 00-7
TM 9-005-239-0 0005 00 3 NOTE Ensure the magazine hook (3) is in the correct space. Tugging on the magazine is a good check for proper seating. 0005 00-8
TM 9-005-239-0 0005 00 CHAMBERING A CARTRIDGE WARNING Ensure the safety is in the "safe" position and that the chamber is clear of any obstruction. 0005 00-9
TM 9-005-239-0 0005 00 WARNING Never try to force a cartridge into the chamber. If the bolt does not fully close, clear any obstructions until a round is successfully chambered. Never attempt to fire a round if the bolt does not fully close.. With the muzzle pointed down range and in a safe direction, move the bolt handle up and all the way to the rear. Release the bolt handle chambering the first round from the magazine. Tap the bolt handle to ensure the bolt is fully forward. WARNING Because the rifle is recoil-operated, the shooter must be positioned squarely behind the weapon, with the recoil pad firmly against the shoulder. Anything less may result in injury, discomfort, or failure of the action to cycle correctly. 2. Shooter is positioned squarely behind the rifle. Rotate safety selector switch to the "FIRE" position. Ensure shoulder pad is properly positioned on shoulder before squeezing the trigger. The rifle will fire one round for each squeeze of the trigger until the magazine and chamber are empty. 0005 00-0
TM 9-005-239-0 0005 00 CHAMBERING A CARTRIDGE - Continued 3. With the safety in the "safe" position and the muzzle pointed in a safe direction, pull the charging handle to the rear until it stops, then release it. The rifle then loads and locks under its own spring power. UNLOADING THE RIFLE WARNING The bolt does not automatically remain to the rear when the rifle or magazine is empty. After the rifle is unloaded, and with the charging handle to the rear, always physically check the chamber to ensure that the rifle is empty.. Place the weapon safety on "safe". Press the magazine catch () forward towards the magazine (2), and remove the magazine. 0005 00-
TM 9-005-239-0 0005 00 2. Pull the charging handle (3) to the rear, which will eject any cartridge still chambered. NOTE Remember that the bolt does NOT automatically remain to the rear when the rifle or magazine is empty. 0005 00-2
TM 9-005-239-0 0005 00 UNLOADING THE RIFLE - Continued 3. After the rifle is unloaded, and with the charging handle (3) to the rear, look into the chamber make certain the breech area and chamber are empty. UNLOADING THE MAGAZINE CAUTION Only remove ammunition from the magazine with your hands. Hold the magazine () with one hand with the cartridge tips (2) facing away from you. Push each of the cartridges out of the magazine until all are ejected. 0005 00-3
TM 9-005-239-0 0005 00 Push Round Forward END OF WORK PACKAGE 0005 00-4
TM 9-005-239-0 0006 00 OPERATOR LONG RANGE SNIPER RIFLE, M07 NSN 005-0-469-233 SIGHTING SYSTEMS 0006 00-
TM 9-005-239-0 0006 00 ZEROING THE IRON SIGHT. Assume a prone-supported firing position 00 meters from the zero target (NSN 6920-00-900-8205). Align index line with the 00-meter range line on the elevation scale (). 2. Align windage index line with windage zero index line on base of iron sight. Align the rear peep sight (2) with the front sight post (3). 0006 00-2
TM 9-005-239-0 0006 00 ZEROING THE IRON SIGHT - Continued NOTE One click of elevation knob (4) moves the strike of the round.6 in. (4.06 cm) at 00 meters. One click of windage knob (5) moves the strike of the round 0.75 in. (.90 cm) at 00 meters. 3. Obtain the proper sight picture by aligning the rear peep sight (2) with front sight post (3). Fire a three round shot group at center mass of the zero target, maintaining the same aim point with each shot. Note the strike of the rounds and make windage and elevation adjustment accordingly. 4. Continue firing three round shot groups, making windage and elevation adjustments as necessary until the shot group is center mass on the zero target. 5. Once the shot group is center mass, loosen the screw (6) on the elevation scale (). Slide the elevation scale until the 00 meter range index line is aligned with the index line on the rear peep sight (2), tighten the screw. END OF WORK PACKAGE 0006 00-3
TM 9-005-239-0 CHAPTER 3 MAINTENANCE INSTRUCTIONS FOR LONG RANGE SNIPER RIFLE, M07
TM 9-005-239-0 0007 00 OPERATOR LONG RANGE SNIPER RIFLE, M07 NSN 005-0-469-233 FIELD STRIPPING 0007 00-
TM 9-005-239-0 0007 00 INTRODUCTION The M07 is field stripped into three major components: upper receiver assembly (), lower receiver assembly (2), bolt and carrier assemblies (3). 0007 00-2
TM 9-005-239-0 0007 00 FIELD STRIPPING WARNING Ensure that the weapon is unloaded and on SAFE before performing these procedures.. Remove rear lock () and midlock (2) pins by press the button of pin and pull it out. 2 0007 00-3
TM 9-005-239-0 0007 00 2. Grasp charging handle (3) on the bolt carrier (4) and pull to the rear until the bolt (5) clears the barrel extension. 0007 00-4
TM 9-005-239-0 0007 00 FIELD STRIPPING - Continued 3. While holding the charging handle (3) to the rear, lift the back end of the upper receiver assembly (6) until it clears the bolt (5). Slowly allow the bolt carrier (4) to return to its forward position. 0007 00-5
TM 9-005-239-0 0007 00 4. Disengage front hook (7) from the front hook pin (8) on the lower receiver (9) and lift upper receiver assembly (6) clear of lower receiver assembly. 6 8 7 9 0007 00-6
TM 9-005-239-0 0007 00 FIELD STRIPPING - Continued WARNING Buffer and buffer spring are under heavy spring tension. 6. Pull the bolt carrier (4) rearward and insert the midlock pin () through the buffer (0) and buffer spring (). 4 0 0007 00-7
TM 9-005-239-0 CAUTION When removing the bolt carrier from the lower receiver assembly, ensure carrier is completely forward of the housing before lifting bolt to avoid damaging lower receiver assembly. 7. Gently pull the bolt carrier (4) forward and lift out of the lower receiver assembly (9). 4 9 END OF WORK PACKAGE 0007 00-8
TM 9-005-239-0 0007 00 OPERATOR LONG RANGE SNIPER RIFLE, M07 NSN 005-0-469-233 EXTRACTOR MAINTENANCE 0008 00-
TM 9-005-239-0 0008 00 REMOVAL WARNING Always point the bolt away from face and eyes to avoid possible injury if parts fly free. CAUTION Cover plunger and plunger spring with thumb while sliding extractor out of slot to prevent loss or damage. NOTE Perform Removal procedure only upon extractor, extractor plunger or extractor spring failure. 0008 00-2
TM 9-005-239-0 0008 00 REMOVAL - Continued. To remove the extractor () from the bolt (2), depress the extractor plunger by inserting a /6 in. punch through the extractor hole (3). 3 2 0008 00-3
TM 9-005-239-0 0008 00 2. Slide the extractor () out of the slot. Remove extractor plunger (3) and extractor spring (5). Visually inspect all components for damage. 3 5 2 INSTALLATION. Insert extractor spring (5) and extractor plunger (3) into bolt (2). 2. Slide the extractor () into the slot. END OF WORK PACKAGE 0008 00-4
TM 9-005-239-0 0009 00 OPERATOR LONG RANGE SNIPER RIFLE, M07 NSN 005-0-469-233 MAINSPRING AND MAINSPRING BUFFER MAINTENANCE 0009 00-
TM 9-005-239-0 0009 00 REMOVAL. Using your finger, push the mainspring buffer () to the rear and place the rear lock pin (2) through the coils of the mainspring (3) and the ports in the mainspring housing (4). 4 3 6 5 2 2. Place your finger into the slot on the lower end of mainspring buffer (), and turn the mainspring buffer so that the groove on the flange lines up with the buffer stop (5) on the lower receiver assembly (6). Remove the rear lock pin (2). Slowly and carefully remove the mainspring buffer () and mainspring (3). 0009 00-2
TM 9-005-239-0 0009 00 INSTALLATION. Slide the mainspring () into the lower receiver assembly (2). Place the mainspring buffer (3) into the mainspring. Guide the mainspring into the housing (4) until the mainspring buffer is even with the housing. Place your finger into the slot on the mainspring buffer, and turn the mainspring buffer so that the grove in its flange lines up with the buffer stop (5) on the lower receiver assembly. 4 2 5 3 0009 00-3
TM 9-005-239-0 0009 00 2. Push the mainspring buffer (3) to the rear of the housing (4) and secure it by placing the rear lock pin (6) through coils of the mainspring () and the ports in the mainspring housing. Using your finger, ensure that the groove and slot are NOT aligned. Remove the rear lock pin. Ease off the pressure until the mainspring buffer stops on the buffer stop (5). 4 5 3 6 END OF WORK PACKAGE 0009 00-4
TM 9-005-239-0 000 00 OPERATOR LONG RANGE SNIPER RIFLE, M07 NSN 005-0-469-233 BARREL MAINTENANCE 000 00-
TM 9-005-239-0 000 00 ASSEMBLY. Carefully pick up the upper receiver assembly (). The barrel (2) will be nested inside the receiver for compact storage and transit. Move the impact bumpers (3) into position on either side of the receiver s central barrel bushing, so that they rest snugly against the bushing. 2 2. Align the barrel (2) so that its feed ramp (slanted entry to the firing chamber) is on the bottom. Keeping fingers away from the barrel, hold the upper receiver assembly () horizontally, then tilt it in the direction of the muzzle (4). The barrel should fall into place, at its full forward extension into the upper receiver assembly. 3 4 000 00-2
ASSEMBLY - Continued TM 9-005-239-0 000 00 WARNING The tension on the barrel springs is about 70 pounds. Serious injury may result if springs are released suddenly. Incomplete or improper assembly may result in injury. 3. The barrel springs (5) at the front of the upper receiver assembly () are held together by the barrel key (6) which acts as a spring yoke. Maintaining the downward tilt of the upper receiver assembly (to keep the barrel in place) firmly grasp the barrel key-not the springs-and pull it into place on the forward slot of the barrel. Work the barrel key from side to side until it is firmly seated in the barrel slot. The upper receiver assembly is now fully assembled. 5 000 00-3 6
TM 9-005-239-0 000 00 STORAGE CAUTION Do not pull on barrel springs to remove the barrel key. Doing so may damage the springs. Barrel spring is under tension.. To nest the barrel () for storage and transit, it is necessary to remove the barrel key (2) from the barrel key slot. 2. Withdraw the barrel key (2) from the slot in the barrel () by slowly working it out. Slide the barrel out the rear of the upper receiver assembly (3). END OF WORK PACKAGE 000 00-4 2
TM 9-005-239-0 CHAPTER 4 SUPPORTING INFORMATION
TM 9-005-239-0 00 00 OPERATOR LONG RANGE SNIPER RIFLE, M07 NSN 005-0-469-233 SNIPER WEAPONS SYSTEM PARTS LIST INTRODUCTION Explanation of Columns in the Sniper Weapons System Parts List Column () Illus Number. Gives you the number of the item illustrated. Column (2) Description. Identifies the item name. Column (3) Qty. Indicates the quantity required. 00 00-
TM 9-005-239-0 00 00 2 3 4 6 7 5 Figure. Long Range Sniper Rifle (LRSR), M07. 00 00-2
() ITEM NO. TM 9-005-239-0 (2) DISCRIPTINON 00 00 (3) QTY BARREL ASSEMBLY 2 UPPER RECEIVER ASSEMBLY 3 BOLT AND CARRIER ASSEMBLY 4 LOWER RECEIVER ASSEMBLY 5 MAGAZINE ASSEMBLY 6 BIPOD ASSEMBLY 7 MONOPOD ASSEMBLY 00 00-3
TM 9-005-239-0 00 00 8 2 4 7 0 3 6 3 20 2 9 9 5 5 8 4 2 6 22 7 00 00-4
TM 9-005-239-0 00 00 () (2) (3) () (2) (3) ITEM NO. DISCRIPTINON QTY ITEM NO. DISCRIPTINON QTY MUZZLE BRAKE 2 MUZZLE BRAKE SCREW 2 3 MUZZLE BRAKE WASHER 2 4 OUTER BARREL 5 INNER BARREL BLOCK 2 6 INNER BARREL 7 HOP UP 8 HOP UP BASE 9 HOP UP BASE COVER 0 GAS VALVE STRIKER BARREL SCREW 4 2 BARREL IMPACT BUMPER 3 HOP UP SCREW 4 HOP UP SPACER 5 SHELL HOLDER SPRING 6 CHAMBER 7 BATTERY BUMPER 8 BARREL EXTENTION 9 SHELL HOLDER 20 SHELL HOLDER CATCH 2 SHELL HOLDER CATCH SPRING 22 SHELL HOLDER STEEL BALL 00 00-5
TM 9-005-239-0 00 00 9 4 8 7 4 3 5 6 2 0 2 3 00 00-6
() ITEM NO. TM 9-005-239-0 (2) DISCRIPTINON 00 00 (3) QTY UPPER RECEIVER 2 SCOPE BASE 3 FRONT SIGHT 4 FRONT SIGHT PIN 5 FRONT SIGHT SPRING 6 FRONT SIGHT CATCH 7 FRONT SIGHT CATCH PIN 8 REAR SIGHT BASE 9 REAR SIGHT BASE SCREW 0 SCOPE BASE SCREW 9 BARREL KEY 2 BARREL SPRING 2 3 BARREL KEY SCREW 4 4 WINDAGE ASSEMBLY 00 00-7
TM 9-005-239-0 00 00 7 3 6 2 4 5 8 00 00-8
() ITEM NO. TM 9-005-239-0 (2) DISCRIPTINON 00 00 (3) QTY CARRYING HANDLE 2 CARRYING HANDLE STICK 3 CARRYING HANDLE MOUNT 4 CARRYING HANDLE CLAMP 5 SCOPE RING BOLT 6 SCOPE RING WASHER 7 CARRYING HANDLE NUT 8 CARRYING HANDLE PIN 00 00-9
TM 9-005-239-0 00 00 3 4 8 5 6 7 2 2 4 9 3 0 00 00-0
() ITEM NO. TM 9-005-239-0 (2) DISCRIPTINON 00 00 (3) QTY REAR SIGHT BODY 2 REAR SIGHT APERTURE 3 ELEVATION SCREW 4 ELEVATION SCREW BALL 5 ELEVATION SCREW SPRING 6 ELEVATION SCREW PIN 7 REAR SIGHT SCALE 8 REAR SIGHT SCALE SCREW 9 REAR SIGHT BASE DETENT 0 REAR SIGHT BASE SPRING WINDAGE SCREW 2 WINDAGE SCREW SPRING 3 WINDAGE KNOB 4 WINDAGE KNOB PIN 00 00-
TM 9-005-239-0 00 00 4 3 5 0 6 5 7 8 4 9 3 2 8 22 2 23 24 20 2 9 6 7 00 00-2
TM 9-005-239-0 00 00 () ITEM NO. (2) DISCRIPTINON (3) QTY () ITEM NO. (2) DISCRIPTINON (3) QTY BOLT CARRIER 2 BOLT ASSEMBLY 3 BOLT CATCH 3 4 5 BOLT SPRING O-RING BOLT SPRING PIN STRIKER 4 BOLT CATCH PIN 6 STRIKER PIN 5 BOLT CATCH PLATE 6 BOLT STOP 7 8 STRIKER SPRING STRIKER CAP 7 BOLT STOP PIN 9 STRIKER EXTENSION 8 ACCELERATOR ROD 20 STRIKER CATCH 9 ACCELERATOR 0 ACCELERATOR PIN 2 22 STRIKER CATCH PIN STRIKER CATCH SPRING ACCELERATOR SCREW 23 STRIKER LEVER 2 BOLT SPRING MOUNT 24 STRIKER LEVER PIN 00 00-3
TM 9-005-239-0 7 4 6 5 2 3 2 0 8 9 00 00-4
() ITEM NO. TM 9-005-239-0 (2) DISCRIPTINON (3) QTY BOLT 2 AIR MUZZLE 3 AIR MUZZLE RUBBER 4 BOLT O-RING 5 EXTRACTOR 6 EXTRACTOR PLUNGER 7 EXTRACTOR SPRING 8 EJECTOR 9 EJECTOR PIN 0 EJECTOR SPRING BOLT SPRING 2 BOLT SPRING PIN 00 00-5
TM 9-005-239-0 00 00 27 9 5 28 22 3 4 6 0 4 5 7 23 2 8 24 6 7 26 2 2 3 20 00 00-6 9 8 25
TM 9-005-239-0 () ITEM NO. (2) DISCRIPTINON LOWER RECEIVER 2 YOKE MOUNT 2 3 BIPOD SHIM BUSHIING 2 4 YOKE MOUNT NUT 2 5 YOKE MOUNT WASHER 2 6 MAGAZINE CATCH 7 MAGAZINE CATCH PIN 8 MAGAZINE CATCH SPRING 9 REAR HANDLE GRIP-RIGHT 0 REAR HANDLE GRIP-LEFT REAR HANDLE GRIP SCREW 2 2 2 REAR HANDLE GRIP-NUT 3 RECOIL PAD 4 RECOIL PAD SCREW 2 (3) QTY () ITEM NO. (2) DISCRIPTINON 5 REAR ASSEMBLY PIN-SAFETY 2 (3) QTY 6 MID ASSEMBLY PIN-SAFETY 7 SAFETY 8 SAFETY DETENT 9 SAFETY SPRING 20 TRIGGER 2 TRIGGER SPRING 22 SEAR ASSEMBLY 23 2 TRIGGER HOUSING PIN 24 PISTOL GRIP 25 PISTOL GRIP SCREW 26 PISTOL GRIP WASHER 27 MAIN SPRING 28 MAIN SPRING BUFFER 00 00-7
TM 9-005-239-0 00 00 3 5 4 2 00 00-8
() ITEM NO. TM 9-005-239-0 (2) DISCRIPTINON 00 00 (3) QTY MAGAZINE BODY 2 MAGAZINE FLOOR PLATE 3 MAGAZINE FOLLOWER 4 MAGAZINE SPRING 5 MAGAZINE BLOCK 00 00-9
TM 9-005-239-0 00 00 3 2 4 00 00-20
() ITEM NO. TM 9-005-239-0 (2) DISCRIPTINON 00 00 (3) QTY BIPOD ASSEMBLY 2 BIPOD DETENT 2 3 BIPOD SPRING 2 4 BIPOD PIN 2 00 00-2
TM 9-005-239-0 00 00 6 2 3 4 5 00 00-22
() ITEM NO. TM 9-005-239-0 (2) DISCRIPTINON 00 00 (3) QTY ELEVATION SCREW 2 ELEVATION COLLAR 3 FOOT WASHER 4 FOOT MONOPOD 5 FOOT SCREW 6 LOCK KNOB 00 00-23