HYDRAULIC OORS APPLICAION» Skid Steer Loaders» etal working machines» renchers» Augers» Agricultural machines» Road building machines» Special vehicles» ine machines» Woodworking and sawmill machinery» Conveyors etc. CONENS Specification data... 18 Function diagrams... 19 21 Dimensions and mounting... 22 24 Shaft extensions... Permissible shaft loads... Dimensions and mounting- V... 26 Dimensions and mounting- 6V... 27 Internal Spline data... 28 Order code... 28 GENERAL A B OPIONS A B» odel - Disc valve, roll-gerotor» Flange with wheel mount» Short motor» Side ports» Shafts - straight, splined and tapered» BSPP ports;» Other special features. EXCELLENCE» High torque and pressure drop» High inlet pressure» High starting torque» Improved efficiency at high pressure drop» Smooth operation at low speed ax. Displacement, ax. Speed, ax. orque, ax. Output, ax. Pressure Drop, ax. Oil Flow, in. Speed, cm /rev [in /rev] [RP] danm [ lb-in] kw [HP] bar [PSI] lpm [GP] [RP] Permissible Shaft Loads dan [lbs] Pressure fluid O O emperature range, C [ F] 2 Optimal Viscosity range, mm /s [SUS] Filtration 724,3 [ 44.2] 75 cont.: 183 [ 162] int.: 229 [227] 7 [94] cont.: [ 36] int.: 35 [58] 15 [4] 5 P= 1 [ 2] a ineral based- HLP(DIN 51524) or H(ISO 6743/4) -4 14 [-4 284] 2 75 [ 98 347] ISO code 2/16 (in. recommended fluid filtration of micron s) Oil flow in drain line Pressure Losses Pressure drop bar [ PSI] 14 [ 23] 21 [ 345] Viscosity Oil flow in drain line 2 mm /s [ SUS] lpm [ GP] 2 [ 98] 35 [ 164] 2 [ 98] 35 [ 164] 2,5 [.66] 1,5 [.396] 5 [ 1.321] 3 [.793] 35 3 2 15 1 5 2 15 1 5 5 75 1 1 Q, lpm 5 1 15 2 3 Q, GP 17
OORS SPECIFICAION DAA ype 2 315 4 47 5 63 7 Displacement, cm /rev [ in /rev] ax. Speed, [RP] 21,4 [ 12.29] 6 75 1,8 [ 15.36] 5 6 326,3 [ 19.9] 38 46 41,9 [.6] 35 365 475 [ 28.97] 26 315 523,6 [ 31.95] 24 285 631, 2 [ 38. 52] 19 23 724 [ 44.2] 17 215 ax. orque 72 [ 6375] 9 [ 7965] 116 [ 1265] 147 [ 131] 171 [ 15135] 172 [ 152] 183 [ 162] 16[ 1416] danm [ lb-in] Peak** 12 [ 93] 128 [ 1133] 163 [ 144] 26 [ 18232] 215 [ 163] 215[163] 229 [ 227] 192[ 17] 115 [ 118] 144 [ 12745] 186 [ 1646] 235 [ 28] 24 [ 2124] 24 [ 2124] 274 [ 24] 24 [ 2124] ax. Output kw [ HP] ax. Pressure Drop bar [ PSI] ax. Oil Flow Peak** 41 [ 55] 7 [94] [ 36] 35 [ 58] 4 [ 58] 1 [ 33] 41 [55] 7 [ 94] [36] 35[58] 4[58] 1[33] 41 [55] 7 [94] [36] 35[58] 4[58] 1[33] 41 [55] 7 [94] [36] 35[58] 4[58] 1[33] 41 [55] 55 [ 74] [36] 315 [ 457] 35 [ 58] 1[33] 37,5 [ 5] 51 [ 68] 23 [ 334] 28 [ 46] 32 [ 464] 1[33] 28 [ 37,5] 42 [ 56] 2[ 29] [ 36] 3[ 435] 1[33] 26 [ 35] 4 [ 54] 16 [ 232] 21[ 345] 26[ 377] 1[33] lpm [ GP] 15 [ 4] 15[4] 15[4] 15[4] 15[4] 15[4] 15[4] 15[4] ax. Inlet Pressure bar [ PSI] ax. Return Pressure Peak** 27 [ 392] 37 [ 537] 42 [ 61] -1 RP 75 [11] 27[392] 37[537] 42[61] 75 [11] 27[392] 37[537] 42[61] 75 [11] 27[392] 37[537] 42[61] 75 [11] 27[392] 37[537] 42[61] 75 [11] 27[392] 37[537] 42[61] 75 [11] 27[392] 37[537] 42[61] 75 [11] 27[392] 37[537] 42[61] 75 [11] without Drain Line or 1-3 RP 4 [58] 4 [58] 4 [58] 4 [58] 4 [58] 4 [58] 4 [58] 4 [58] ax. Pressure >3 RP 2 [29] 2 [29] 2 [29] 2 [29] 2 [29] - - - in Drain Line, bar [ PSI] -max. RP 75 [11] 75 [11] 75 [11] 75 [11] 75 [11] 75 [11] 75 [11] 75 [11] ax. Return Pressure with Drain Line bar [ PSI] Peak** 14 [ 2] 14 [ 2] 14 [ 2] 14 [ 2] 175 [ ] 175 [ ] 175 [ ] 175 [ ] 21 [ 3] 21 [ 3] 21 [ 3] 21 [ 3] 14 [ 2] 14 [ 2] 14 [ 2] 14 [ 2] 175 [ ] 175 [ ] 175 [ ] 175 [ ] 21 [ 3] 21 [ 3] 21 [ 3] 21 [ 3] ax. Starting Pressure with Unloaded Shaft, bar [ PSI] 6 [9] 6 [9] 6 [9] 6 [9] 6 [9] 6 [9] 6 [ 9] 6 [ 9] in. Starting orque danm [ lb-in] 6 [ 531] 75 [ 664] 97 [ 8585] 122 [ 18] 142 [ 17] 143 [ 12655] 145 [ 1283] 148[ 131] in. Speed***, [RP] 5 5 5 5 5 5 5 5 Weight, kg [ lb] 26,9 [ 59.3] 27,3 [ 6.2] 28,1 [ 62] 29 [ 64] 29,7 [ 65.5] 3,2 [ 66.6] 29, 7 [ 65. 5] 31 [ 68.4] W 27,4 [ 6.4] 27,8 [ 61.3] 28,6 [ 63.1] 29,5 [ 65.1] 3,2 [ 66.6] 3,7 [ 67.7] 3, 2 [ 66.6] 31,5 [ 69.5] V 15,7 [ 34. 6] 16,1 [ 35. 5] 16,9 [ 37.3] 17,8 [ 39.3] 18,5 [ 4.8] 19 [ 41.9] 18,5 [ 4.8] 19,8 [ 43.7] * Intermittent operation: the permissible values may occur for max. 1% of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds lower than given, consult factory or your regional manager. 1. Intermittent speed and intermittent pressure must not occur simultaneously. 2. Recommended filtration is per ISO cleanliness code 2/16. A nominal filtration of micron or better. 3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil, HLP(DIN51524) or H(ISO6743/4). If using synthetic fluids consult the factory for alternative seal materials. 4. Recommended minimum oil viscosity 7 SUS [13 mm²/s] at 5 C [122 F]. 5. Recommended maximum system operating temperature is 82 C [18 F]. 6. o assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 1-15 minutes. 18
OORS FUNCION DIAGRAS lb-in 12 danm 14 Q=1 l/min 2.65 GP 2 l/min 5.3 GP 4 l/min 1.6 GP 6 l/min 15.85 GP 8 l/min 21.2 GP 1 l/min 26.4 GP 1 l/min 33 GP 15 l/min 39.6 GP 1 8 6 4 2 12 1 8 6 4 2 cont. int. N=2,5 kw 1 kw 5 kw 2 kw 4 kw 3 kw 85% t=86% 83% 8% 6 kw 5 kw 78% cont. 7% 75% 6% int. p=35 bar 575 PSI 3 bar 4715 PSI 3 bar 435 PSI 275 bar 399 PSI bar 36 PSI 2 bar 3265 PSI 2 bar 29 PSI 16 bar 232 PSI 12 bar 174 PSI 8 bar 116 PSI 4 bar 58 PSI n -1 5 1 15 2 5 4 45 5 55 6 min (rpm) 315 lb-in 16 danm 175 Q=1 l/min 2.65 GP 2 l/min 5.3 GP 4 l/min 1.6 GP 6 l/min 15.85 GP 8 l/min 21.2 GP 1 l/min 26.4 GP 1 l/min 33 GP 15 l/min 39.6 GP 14 12 1 8 6 4 2 15 1 1 75 5 cont. int. 5 kw N=2,5 kw 1 kw 2 kw t=88% 87% 5 kw 4 kw 85% 83% 3 kw -1 5 1 15 2 5 4 45 5 min (rpm) cont. 8% 75% 7% 6% he function diagrams data was collected at back pressure 5 1 bar (72.5PSI 145PSI) O and oil with viscosity of 32 mm²/s [15SUS] at 5 C [122 F]. int. p=35 bar 575 PSI 3 bar 4715 PSI 3 bar 435 PSI 275 bar 399 PSI bar 36 PSI 2 bar 3265 PSI 2 bar 29 PSI 16 bar 232 PSI 12 bar 174 PSI 8 bar 116 PSI 4 bar 58 PSI n 19
OORS FUNCION DIAGRAS 4 lb-in 2 danm 2 Q=1 l/min 2.65 GP 2 l/min 5.3 GP 4 l/min 1.6 GP 6 l/min 15.85 GP 8 l/min 21.2 GP 1 l/min 26.4 GP 1 l/min 33 GP 15 l/min 39.6 GP 18 16 14 12 1 8 6 4 2 2 175 15 1 1 75 5 cont. int. 6 kw 4 kw 5 kw 3 kw t=87% 1 kw 2 kw 5 kw 86% 85% 78% N=2,5 kw 83% 8% 75% 7% 6% cont. int. p=35 bar 575 PSI 3 bar 4715 PSI 3 bar 435 PSI 275 bar 399 PSI bar 36 PSI 2 bar 3265 PSI 2 bar 29 PSI 16 bar 232 PSI 12 bar 174 PSI 8 bar 116 PSI 4 bar 58 PSI n -1 5 1 15 2 5 4 min (rpm) 47 lb-in 22 2 18 16 14 12 1 8 6 4 2 danm 2 2 175 15 1 1 75 5 cont. int. Q=1 l/min 2.65 GP 2 l/min 5.3 GP 5 kw 4 l/min 1.6 GP N=2,5 kw 6 l/min 1 kw 2 kw t=87% 15.85 GP 8 l/min 85% 21.2 GP 1 l/min 26.4 GP 3 kw 4 kw 83% 8% 1 l/min 33 GP 75% 5 kw cont. 78% 6% 15 l/min 39.6 GP 7% int. p=35 bar 575 PSI 3 bar 4715 PSI 3 bar 435 PSI 275 bar 399 PSI bar 36 PSI 2 bar 3265 PSI 2 bar 29 PSI 16 bar 232 PSI 12 bar 174 PSI 8 bar 116 PSI 4 bar 58 PSI n -1 5 1 15 2 5 min (rpm) he function diagrams data was collected at back pressure 5 1 bar (72.5PSI 145PSI) and oil with viscosity of 32 mm²/s [15SUS] at 5 C [122 O F]. 2
OORS FUNCION DIAGRAS 5 lb-in 2 18 16 14 12 1 8 6 4 2 danm 2 2 175 15 1 1 75 5 cont. int. Q=1 l/min 2.65 GP 2 l/min 5.3 GP 4 l/min N=2,5 kw 1.6 GP 1 kw 5 kw 6 l/min 15.85 GP 8 l/min 21.2 GP 2 kw 3 kw t=86% 83% 4 kw 5 kw -1 5 1 15 2 3 min (rpm) 1 l/min 26.4 GP 1 l/min cont. 33 GP 78% 75% 15 l/min 8% 7% 6% int. 39.6 GP p=3 bar 4715 PSI 3 bar 435 PSI 275 bar 399 PSI bar 36 PSI 2 bar 3265 PSI 2 bar 29 PSI 16 bar 232 PSI 12 bar 174 PSI 8 bar 116 PSI 4 bar 58 PSI n 63 lb-in 22 danm Q=1 l/min 2.65 GP 2 l/min 5.3 GP 4 l/min 1.6 GP 6 l/min 15.85 GP 8 l/min 21.2 GP 1 l/min 26.4 GP 1 l/min 33 GP 15 l/min 39.6 GP 2 18 16 14 12 1 8 6 4 2 2 2 175 15 1 1 75 5 cont. int. 1 kw N=2,5 kw 5 kw t=87% 85% 3 kw 4 kw 2 kw 78% 83% 8% 75% 7% 6% bar 36 PSI 2 bar 3265 PSI 2 bar 29 PSI 16 bar 232 PSI 12 bar 174 PSI 8 bar 116 PSI 4 bar 58 PSI cont. int. n -1 5 75 1 1 15 175 2 2 min (rpm) he function diagrams data was collected at back pressure 5 1 bar (72.5PSI 145PSI) and oil with viscosity of 32 mm²/s [15SUS] at 5 C [122 O F]. 21
OORS DIENSIONS AND OUNING DAA - and C K Shaft C,CO Shaft SH Shaft Shaft Dim. See Page K Shaft C,CO Shaft SH Shaft 4...4,4 [1.575...1.59] 82 [3.228] 82 [3.228] Flange Dim. See Page 24 3,8...31,2 [1.212...1.228] P (A,B) 21±,15 [.827±.59] 82 [3.228] 82 [3.228] 55,4 [2.181] 82,5 [3.248] max L L2 L1 max L L1 L2 42±,15 [1.653±.59] 42±,15 [1.653±.59] P (A,B) Port A F Port B - Drain port G1/4 +,4 ø21 [.827 +.157] F 139 12 [.472] 1 [.394] Warning: Drain line should always be used. 72 [2.834] Standard Rotation Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Port A Pressurized - CCW Port B Pressurized - CW 22 P (A, B) : 2xG3/4-17 mm [.669 in] depth : G1/4-12 mm [.472 in] depth (plugged) ype L, mm [in] L, 2 mm [in] ype L, mm [in] L 2, mm [in] L, 1 mm [in] 2 188 [ 7.4] 142,3[ 5.6] C 2 198 [ 7.79] 153 [ 6.2] [.98] 194 [ 7.64] 148,6 [ 5.85] 315 23 [ 7.99] 157,8 [ 6.21] C 24,5 [ 8.5] 159,3 [ 6.27] 31,3 [ 1.23] C 315 213,5 [ 8.4] 168,5 [ 6.63] 4,5 [ 1.59] 4 214 [ 8.43] 168,3 [ 6.63] 47 222 [ 8.74] 176,3 [ 6.94] 5 228 [ 8.98] 182,3 [ 7.18] 63 224 [ 8.82] 178,3 [ 7.2] 7 233 [ 9.17] 187,3 [ 7.37] C 4 C 47 C 5 C 63 C 7 224 [ 8.82] 232 [ 9.13] 238 [ 9.37] 234 [ 9.21] 243 [ 9.56] 179 [ 7.4] 187 [ 7.36] 193 [ 7.6] 189 [ 7.44] 198 [ 7.79] 51 [ 2.1] 59 [ 2.32] 65 [ 2.56] 61 [ 2.4] 7 [ 2.76] mm [in]
OORS DIENSIONS AND OUNING DAA - W K Shaft C, CO Shaft SH Shaft Shaft Dim. See Page 99,2...99,8 [3.95...3.929] 82 [3.228] 82 [3.228] Flange Dim. See Page 24 L3 L2 L1 Port Dim. See Page 22 max L P (A,B) Port A Port B Warning: Drain line should always be used. P (A, B) : 2xG3/4-17 mm [.669 in] depth : G1/4-12 mm [.472 in] depth (plugged) ype W 2 W W 315 W 4 W 47 W 5 W 63 W 7 L, mm [in] 129 [ 5.8] 135 [ 5.32] 144 [ 5.67] 155 [ 6.1] 163 [ 6.42] 169 [ 6.65] 165 [ 6.5] 174 [ 6.85] L, 1 mm [in] [.98] 31,3 [ 1.23] 4,5 [ 1.59] 51 [ 2.1] 59 [ 2.32] 65 [ 2.56] 61 [ 2.4] 7 [ 2.76] L, 2 mm [in] L, 3 mm [in] 83,8 [ 3.3] 111,1 [ 3.37] 9,1 [ 3.55] 117,4 [ 4.62] 99,3 [ 3.91] 126,6 [ 4.98] 19,8 [ 4.32] 137,1 [ 5.4] 117,8 [ 4.64] 145,1 [ 5.71] 123,8 [ 4.87] 151,1 [ 5.95] 119,8 [ 4.72] 147,1 [ 5.79] 128,8 [ 5.7] 156,1 [ 6.15] Standard Rotation Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Port A Pressurized - CCW Port B Pressurized - CW mm [in] 23
OORS OUNING 4-Bolt flange spigot diameter ø16 mm [6.3 in] - BC ø2 [7.874 in] mm 4xø18±,15 [.78±.59] ø2±,4 [7.874±.157] 9 [.354] 4,2 [1.582] C 4-Bolt flange spigot diameter ø1 mm [4.921 in] - BC ø16 mm [6.3 in] 4xø14 +,3 +,1 +.39 [.551 +.118] ø16±,4 [6.3±.157] R16 [.63] 9±,5 [.354±.197] 21±,5 [.827±.197] W 4-Bolt flange, Wheel otor spigot diameter ø16 mm [6.3 in] - BC ø2 mm [7.874 in] 4xø18±,15 [.78±.59] ø2±,4 [7.874±.157] 7 [.275] 42 [1.653] 18 [7.86] ø172 -,63 [6.772 ] -. ø1 -,1 [4.921 ] -.39 ø16 -,63 [6.299 ] -. 147 [5.787] ø1 -,1 -,5 -.4 -.19 [4.921 ] 18 [7.86] ø98±,5 [3.858±.197] ø16 -,63 [6.299 ] -. 24 [.945] 4 21 [.157] [.827] mm [in] 24
OORS C - ø4 straight, Parallel key A12x8x7 DIN 6885 ax. orque 132,8 danm [11755 lb-in] SHAF EXENSIONS SH - ø1½" splined 17, DP 12/24 ANSI B92.1-1976 ax. orque 132,8 danm [11755 lb-in] R2±,2 [.787±.78] 45 R2±,2 [.787±.78] R2±,2 [.787±.78] 45 R2±,2 [.787±.78] Pitch 12/24 eeth 17 Pressure angle 3 12 -,43 [.472-.17] 82-,2 [3.228 ] -.79 5:1 82-,2 [3.228 ] -.79 ø5 [1.968] ø4 +,18 -,2 +.7 -.1 [1.575 ] ø5 [1.968] 12 min [.984] Deep 12 min [.984] Deep 56 [2.] K - tapered 1:1, Parallel key B12x8x28 DIN 6885 ax. orque 21,7 danm [1865 lb-in] ø5 [1.968] 82-,2 [3.228 -.79] 4 B [.157] 6 [.236] 3x2 ø56 [2.] 12 +,1 -,5 [.472 +.4 -.19 ] B-B 54±,4 [2.126±.157] aper 1:1 B ø6 [.236] S=46 ightening orque 5±3 danm [44±265 lb-in] 16,15-,2 43 -,2 [1.693 ] -.79 ø38,1-, [1.5 ] -.1 -ø1½" straight, Parallel key 3 "x 3 CO 8 8 "x 2¼" BS46 ax. orque 132,8 danm [11755 lb-in] R2±,2 [.787±.78] 9.545 -,2 [.379 ] -.8 45 R2±,2 [.787±.78] 82-,2 [3.228 ] -.79 42,4 -,2 [1.669 ] -.79 3/8-16 UNC min [.984] deep ø5 [1.968] ø38,1-,5 [1.5 ] -.19 [.634 ] -.79 mm [in] PERISSIBLE SHAF LOADS he curves apply to a B1 bearing life (ISO281) of 2 hours at 2 RP. Pr Pr lbs dan 56 12 5 Pr Pr lbs dan 56 12 5 C 1 4 8 1 4 8 3 6 3 6 2 4 2 4 2 1 2 1-8 -6-4 -2 2 4 6 8 1 12 14 16 mm -8-6 -4-2 2 4 6 8 1 12 14 16 mm -3-2 -1 1 2 3 4 5 6 7 in Pr Pr lbs dan 56 12 5 1 4 8 3 6 2 4 2 1 W -3-2 -1 1 2 3 4 5 6 in -8-6 -4-2 2 4 6 8 1 12 14 16 mm -3-2 -1 1 2 3 4 5 6 7 in
OORS DIENSIONS AND OUNING DAA - V 45,6-1 [1.795 -.394] 14 max [.551] 21±,2 [.827±.78] ø11±,1 [4.33±.39] Port B 9x12 [5.472 ] -,2 -.79 84±,3 [3.37±.118] 139 Port A P (A,B) L3 L1 L2 max L 72 [2.834] P (A, B) mm [in] Warning: Drain line should always be used. : 2xG3/4-17 mm[.669 in] depth : G1/4 12 mm [.472 in] depth (plugged) Standard Rotation Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Port A Pressurized - CCW Port B Pressurized - CW ype L, mm [in] L, 1 mm [in] V 2 151 [ 5.945] [.98] V 157 [ 6.181] 31,3 [ 1.23] V 315 167 [ 6.575] 4,5 [ 1.59] V 4 177 [ 6.968] V 47 185 [ 7.283] V 5 191 [ 7.52] V 63 187 [ 7.362] V 7 196 [ 7.717] 51 [ 2.1] 59 [ 2.32] 65 [ 2.56] 61 [2.4] 7 [2.76] L, 2 mm [in] L, 3 mm [in] 16,5 [ 4.193] 27,8 [ 1.94] 112,8 [ 4.441] 26,5 [ 1.43] 122, [ 4.83] 22,3 [.878] 132,5 [ 5.217] 21,8 [.858] 14,5 [ 5.531] 23,8 [.937] 146,5 [ 5.768] 27,8 [ 1.94] 142,5 [ 5.61] 21,8 [.858] 151,5 [ 5.965] 22,8 [.898] DIENSIONS OF HE AACHED COPONEN F +,5 47 +.197 [1.85 ] +,4 17 [.669 +.157] K 16DP 12/24 ANS B92.1-76 min ø55 [2.165] ø9 [3.543] J I F: Oil circulation hole J: 9x12-3 mm [1.181 in] depth, 4, ø11±,1 [4.33±.39] I: O- Ring 93x1,5mm [3.661x.59 in] : Drain connection G1/4 26
OORS DIENSIONS AND OUNING DAA - 6V 45,6-1 [1.795 -.394] 14 max [.551] 21±,2 [.827±.78] 4 1 ø11±,1 [4.33±.39] Port B -,2 -.79 [5.472 ] 84±,3 [3.37±.118] 6x12 2 2 139 Port A L3 L2 L1 max L P (A,B) 4 1 Fig.1 72 [2.834] mm [in] Warning: Drain line should always be used. P (A, B) : 2xG3/4-17 mm[.669 in] depth : G1/4 12 mm [.472 in] depth (plugged) Standard Rotation Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Port A Pressurized - CCW Port B Pressurized - CW ype L, mm [in] L, 1 mm [in] 6V 2 151 [ 5.945] [.98] 6V 157 [ 6.181] 31,3 [ 1.23] 6V 315 167 [ 6.575] 4,5 [ 1.59] 6V 4 177 [ 6.968] 6V 47 185 [ 7.283] 6V 5 191 [ 7.52] 6V 63 187 [ 7.362] 6V 7 196 [ 7.717] 51 [ 2.1] 59 [ 2.32] 65 [ 2.56] 61 [2.4] 7 [2.76] L, 2 mm [in] L, 3 mm [in] 16,5 [ 4.193] 27,8 [ 1.94] 112,8 [ 4.441] 26,5 [ 1.43] 122, [ 4.83] 132,5 [ 5.217] 14,5 [ 5.531] 22,3 [.878] 21,8 [.858] 23,8 [.937] 146,5 [ 5.768] 27,8 [ 1.94] 142,5 [ 5.61] 21,8 [.858] 151,5 [ 5.965] 22,8 [.898] DIENSIONS OF HE AACHED COPONEN FOR 6V F +,5 47 +.197 [1.85 ] +,4 17 [.669 +.157] J K 16DP 12/24 ANS B92.1-76 min ø55 [2.165] ø9 [3.543] I F: Oil circulation hole J: 9x12-3 mm [1.181 in] depth, 4, ø11±,1 [4.33±.39] or 6x12-3 mm [1.181 in] depth, situated in accordance with the bolts 12, shown on Fig.1, ø11±,1 [4.33±.39] DRAIN CONNECION A drain line ought to be used when pressure in the return line can exceed the permissible pressure. It can be connected to the drain connection of the attached component. he maximum pressure in the drain line is limited by the attached component and its shaft seal. he drain line must be possible for oil to flow freely between motor and attached component and must be led to the tank. he maximum pressure in the drain line is limited by the attached component and its seal. 27 I: O- Ring 93x1,5mm [3.661x.59 in] : Drain connection G1/4
OORS INERNAL SPLINE DAA FOR HE AACHED COPONEN Standard ANS B92.1-1976, class 5 [m=2.1166; corrected x.m=+1,] Fillet Root Side Fit Number of eeth Diametral Pitch Pressure Angle Pitch Dia. ajor Dia. inor Dia. Circular Space Width Fillet Radius Dimension Between wo Pins Pin Dia. z DP D Dri Di Lo R L d inch mm 16 16 12/24 12/24 3 3 1.3333,8656 +,4 1.5118 1.5275 38,4 +,4 1.2657 1.2672,15.1763.1791 4,516±,37.2,5 +,1 1.63 1.59 26,9.1926.1934 4,835±,1 L Hardening Specification: HV=75±5 on the surface. HV=56 at,7±,2 [.35.19] case depth aterial: 2 ocr4 EN 184 or SAE862. ORDER CODE 1 2 3 4 5 6 7 Pos.1 - ounting Flange omit - 4-Bolt flange, spigot dia. ø16, BC ø2 C - 4-Bolt flange, spigot dia. ø1, BC ø16 W - Wheel motor V - Very short mount, 9x12 mounting bolts 6V - Very short mount, 6x12 mounting bolts Pos.2 - Displacement code 2-21,4 cm /rev [12.29 in /rev] - 1,8 cm /rev [15.36 in /rev] 315-326,3 cm /rev [19.9 in /rev] 4-41,9 cm /rev [.6 in /rev] 47-475, cm /rev [28.97 in /rev] 5-523,6 cm /rev [31.95 in /rev] 63-631,2 cm /rev [38. 52 in /rev] 7-724, 3 cm /rev [44.2 in /rev] Pos.3 - Shaft Extensions* C CO K SH - ø4 straight, Parallel key A12x8x7 DIN6885 - ø1½ straight, Parallel key / x / x2¼ BS46 - ø45 tapered 1:1, Parallel key B12x8x28 DIN6885 - ø1½" splined 17 ANSI B92.1-1976 Pos.4 - Check Valves omit - without check valves 1 - with check valves Pos.5 - Ports omit - BSPP (ISO 228) Pos.6 - Special Features (see page 48) Pos.7 - Design Series omit - Factory specified 8 8 NOES: * he permissible output torque for shafts must not be exceeded! he hydraulic motors are mangano-phosphatized as standard. 28