Parflex/Atlantic Fluoropolymer Tubing Products

FluidConnectors Fluoropolymer Tubing Products Catalog 4150/USA April 2004

Table of Contents Introduction... 3 Part Number Matrix... 3 Summary of Properties... 4 Fluid Handling Tubing & Pipe HP PFA Products Product Overview... 5 Fractional Size Tubing... 6 Metric Size Tubing... 6 Retractable Coils... 7 Dual Containment Tubing... 8 PFA Products Product Overview... 9 Fractional Size Tubing... 10 Metric Size Tubing... 11 Convoluted Tubing... 11 Retractable Coils... 12 FEP Products Product Overview... 13 Fractional Size Tubing... 14 Metric Size Tubing... 15 Convoluted Tubing... 15 Retractable Coils... 16 PTFE Products Product Overview... 17 Fractional Size Tubing... 18 Metric Size Tubing... 19 Convoluted Tubing... 19 PVDF Products Product Overview... 20 Fractional Size Tubing... 21 Metric Size Tubing... 22

Fluoropolymer Tubing Overview manufactures an extensive line of high quality fluoropolymer tubing and pipe. A wide range of products are available in PTFE, FEP, PFA, High Purity PFA, and PVDF. Other materials such as ETFE, MFA and PEEK are also available on request (minimums will apply). All tubing and pipe products are made from 100% virgin resins. These fluoropolymers are resistant to numerous chemicals and solvents. A detailed outline of the chemical compatibility and other technical information is beyond the scope of this catalog. However, a comprehensive technical and chemical compatibility bulletin is available. Please ask for Technical Bulletin 0002-T1/USA. Part Number Matrix 105-0250062-N40025-X Outside Diameter Example: 0250 =.250 Inches 0700 = 7 mm Wall Thickness Example: 062 =.062 Inches 100 = 1 mm Packaging 1 = HP Spool 2 = Plastic Spool 3 = Wood Spool 4 = Coil 5 = Straight 6 = Cardboard Spool 0 = Other C = Cut Length (Inches)* Product Family 1 = Fractional 2 = Metric 3 = Convoluted 4 = Spiral Cut 5 = Pipe 7 = Retractable Coils 9 = Custom A = Formed Part Resin 01 = PTFE 03 = FEP 04 = PFA 05 = PFA, HP Generic 06 =PFA, Teflon 450HP 07 = PFA, Teflon 440HP 09 = MFA 10 = PVDF 11 = PVDF, Superflex 12 = ETFE 13 = PEEK Solid Color* 0 = Black 1 = Brown 2 = Red 3 = Orange 4 = Yellow 5 = Green 6 = Blue 7 = Violet 8 = Gray 9 = White N = Natural Length 1000 = 1,000 ft. 0500 = 500 ft. 0250 = 250 ft. 0100 = 100 ft. 0050 = 50 ft. 0025 = 25 ft. 0010 = 10 ft. 0005 = 5 ft. 0004 = 4 ft. Stripe Color* Only add suffix if Stripe is required. 0 = Black 1 = Brown 2 = Red 3 = Orange 4 = Yellow 5 = Green 6 = Blue 7 = Violet 8 = Gray 9 = White Teflon is a registered trademark of DuPont. Consult Price List for individual configuration pricing. For other configurations not listed on Price List, consult factory. *Additional charges and minimums will apply for colored, color stripes or cut pieces. Please consult the factory. 3

Fluoropolymer Tubing Summary of Properties The table below lists the summary of mechanical, electrical and thermal properties of the resins from which manufactures its line of tubing and pipe. MECHANICAL PROPERTIES ASTM UNITS PFA FEP PTFE PVDF Tensile Strength D 1708 PSIG 4,000 3,500 2,500-4,000 D638 13,000 Specific Gravity D792 2.15 2.15 2.13-2.24 1.8 Coefficient of Friction Dynamic (<10 ft/min) 0.2 0.2 0.1 0.14 0.17 Compressive Strength D695 PSIG 2,200 3,500 11,600 Impact Strength 73 F D256 Ft-Lb/in No Break No Break 3.5 3-6 Flexural Modulus 73 F D 790 PSIG 95,000 95,000 27,000 Tensile Modulus D638 PSIG 40,000 60,000 80,000 348,000 Hardness-Durometer D 2240 D-60 D-55 D-50-65 D-76-80 Elongation D 1708 % 300 300 200-400 D 638 150 Flexural Strength D 790 PSIG No Break No Break No Break 10,750 Water Absorption D 570 % 0.03 <0.01 <0.01 <0.04 Deformation Under Load (73 F, 1000 PSIG, 24 HR) D 621 2.0 1.8 3.5 Linear Coefficient of Expansion (70-212 F) (212-300 F) (300-408 F) D 696 in/in/ F 6.7 x 10 5 5 4.5-5.8 x 10 9.4 x 10 5 11.1 x 10 5 3.8 5 x 10 5 5 7.1 x 10 4.2 5 x 10 5 5.0 5 x 10 5 Flex Life (MIT) 15,000 15,000 >1,000,000 Creep Resistance D674 LB/Sq In 40,000 ELECTRICAL PROPERTIES Dielectric Strength (Short Term) 10 Mil Film ASTM UNITS PFA FEP PTFE PVDF D 149 V/Mil >2,000 >2,000 >1,400 >1,080 Volume Resistivity D 257 ohm-cm 10 18 >10 18 >10 18 10 13 Surface Resistivity D 257 ohm/sq >10 17 >10 16 >10 18 THERMAL PROPERTIES ASTM UNITS PFA FEP PTFE PVDF Continuous Service Temperature F 500 400 500 235 Melting Point DTA F 575-590 500-530 635-650 352 Thermal Conductivity C-177 BTU/hr/ft 2 / F. in 1.32 1.4 1.7 1.31 Heat of Fusion BTU/lb 13 11 29-37 Specific Heat 25 C 100 C 200 C 275 C C-177 Cal/g/ C 0.256 0.283 0.334 0.381 0.26 0.23 0.25 0.27 0.29.30-.34 Deflextion Temperature 66 PSI 264 PSI F 166 118 138 134 252 131 235 Heat of Combustion BTU/lb 2,200 2,200 OTHER PROPERTIES ASTM UNITS PFA FEP PTFE PVDF Flammability Rating UL 94 VO VO VO VO Retractive Index D 542 1.35 1.338 1.35 Limiting Oxygen Index >95 >95 >95 4

HP PFA Fluid Handling Tubing Product Overview High Purity PFA (Perfluoroalkoxy) tubing, made from 100% virgin resin, has the highest molecular weight available. It is manufactured for use in hostile environments where purity is critical. Testing has proven that these High Purity PFA products are able to withstand corrosive surfactants for longer periods of time than the standard products. High Purity PFA products are available in various sizes upon request. Features 100% virgin PFA resin used on all products. Semiconductor and pharmaceutical specification conformance. Translucent and flexible materials. Chemically inert to nearly all industrial chemicals and solvents. Smooth nonstick surface resulting in the lowest coefficient of friction. Lowest levels of extractables. Nonflammable materials. FDA Compliant. Benefits No process contamination. High Purity applications. Excellent for flow monitoring systems. Longer product life and less downtime. Higher flow with no process contamination. Excellent for high purity applications. Safety. Useful in food applications. Specifications Materials: Products in this catalog are manufactured using resins complying with ASTM D 3307 Type II Specification. Flammability: Listed VW-1 by the Underwriters Laboratories, Inc. in their burning test classification for polymeric materials and passes the UL 83 vertical flame test. In a flame situation, High Purity PFA tubing resists combustion and does not promote flame spread. FDA Compliance: Most high purity PFA resins qualify for use in contact with food in compliance with FDA regulation 21 CFR 177.1550. Pressure and Temperature Ranges: See pressure temperature chart or consult the factory. 400 350 300.062 wall Pressure vs. Temperature Chart Heavy Wall High Purity PFA Tubing Fractional Size 38 Media Temperature ( C) 65 93 121 149 176 1/4" 3/8" 1/2" 3/4" 1" 204 27.58 24.13 20.68 Pressure (PSIG) 250 200 150.047 wall.062 wall.047 wall.062 wall 17.24 13.79 10.34 Pressure (bar) 100.062 wall 6.90 50.062 wall 3.45 0 100 150 200 250 Media Temperature ( F) 300 350 400 5

HP PFA Fluid Handling Tubing Part numbers below are for standard configurations. For complete part numbers and options for material, color, packaging, etc. refer to Part Number Matrix on page 3. Industrial Wall Fractional Size Tubing OD Part Number OD X ID X Wall Heavy Wall Fractional Size Tubing OD Wall Minimum Bend Radius Working PSIG (bar) Burst PSIG (bar) 1/8" 105-0125031-XXXXXX 1/8" X 1/16" X.031 ±.004 ±.003 1/2" 369 (25.4) 1,859 (128.2) 3/16' 105-0188031-XXXXXX 3/16" X 1/8" X.031 ±.005 ±.003 1/2" 249 (17.1) 1,253 (86.4) 1/4" 105-0250031-XXXXXX 1/4" X 3/16" X.031 ±.005 ±.003 1" 190 (13.1) 945 (65.2) 3/8" 105-0375031-XXXXXX 3/8" X 5/16" X.031 ±.005 ±.003 2-1/2" 125 (8.6) 633 (43.6) 1/2" 105-0500031-XXXXXX 1/2" X 7/16" X.031 ±.006 ±.003 4" 95 (6.6) 476 (32.8) 3/4" * 105-0750032-XXXXXX 3/4" X 11/16" X.032 ±.006 ±.003 16" 68 (4.7) 318 (21.9) OD Part Number OD X ID X Wall OD Wall Minimum Bend Radius Working PSIG (bar) Burst PSIG (bar) 3/16' 105-0188062-XXXXXX 3/16" X 1/16" X.062 ±.005 ±.003 1/2" 492 (33.9) 2,478 (170.9) 1/4" 105-0250047-XXXXXX 105-0250062-XXXXXX 1/4" X 5/32"" X.047 1/4" X 1/8" X.062 ±.005 ±.003 3/4" 1/2" 286 (19.7) 380 (26.2) 1.443 (99.5) 1,889 (130.2) 3/8" 105-0375062-XXXXXX 3/8" X 1/4" X.062 ±.005 ±.003 3/4" 260 (17.9) 1.280 (88.3) 1/2" 105-0500062-XXXXXX 1/2" X 3/8" X.062 ±.006 ±.003 2-1/2" 95 (6.6) 476 (32.8) 3/4" 105-0750062-XXXXXX 3/4" X 5/8" X.062 ±.006 ±.003 6" 68 (4.7) 318 (21.9) 1" 105-1000062-XXXXXX 1" X 7/8" X.062 ±.010 ±.003 16" 100 (6.9) 490 (33.8) 1-1/8" * 105-1125062-XXXXXX 1-1/8" X 1' X.062 ±.015 ±.003 24" 87 (6.0) 436 (30.1) 1-1/4" * 105-1250075-XXXXXX 1-1/4" X 1.10 X.075 ±.015 ±.003 16" 94 (6.5) 474 (32.7) Pressures above are for operation at 73 F. Working pressure calculated using a Design Factor of 5. Note other manufacturers may use a Design Factor of 4. Fractional tubing is supplied in 25 ft. increments up to 1000 ft. continuous for sizes up to 1 OD. Standard packaging for sizes greater than 1 OD are 5 and 10 ft. straight lengths. Custom packaging and sizes are quoted upon request. Metric Size Tubing OD Part Number OD X ID X mm OD X ID X Inch Consult factory for pressure ratings. OD / ID mm/inch Minimum Bend Radius 3 205-0300100-XXXXXX 3.0 X 1.0.118 X.039 ±.11 ±.004 N/A 4 205-0400100-XXXXXX 4.0 X 2.0.157 X.078 ±.11 ±.004 1/2" 5 205-0500100-XXXXXX 5.0 X 3.0.197 X.118 ±.11 ±.004 1/2" 6 205-0600100-XXXXXX 6.0 X 4.0.236 X.157 ±.13 ±.005 3/4" 7 205-0700100-XXXXXX 7.0 X 5.0.276 X.197 ±.13 ±.005 3/4" 8 205-0800100-XXXXXX 8.0 X 6.0.315 X.236 ±.13 ±.005 1" 9 205-0900100-XXXXXX 9.0 X 7.0.354 X.276 ±.13 ±.005 1-1/2" 10 205-1000100-XXXXXX 10.0 X 8.0.393 X.315 ±.13 ±.005 2" 12 * 205-1200100-XXXXXX 12.0 X 10.0.472 X.393 ±.15 ±.006 2-1/2" 14 * 205-1400100-XXXXXX 14.0 X 12.0.551 X.472 ±.15 ±.006 3-3/8" 16 * 205-1600100-XXXXXX 16.0 X 14.0.630 X.551 ±.15 ±.006 4-1/4" * Non-Standard Product - Order Minimum Will Apply 6

HP PFA Fluid Handling Tubing Retractable Coils Left Length A Right Length Part Number OD X ID Coil ID Inch (mm) Retracted Length "A" Inch (mm) Extended Length Inch (mm) 705-0188062-XX0003 3/16" X 1/16".750 (19.1) 3 (76) 12 (305) 705-0188062-XX0006 3/16" X 1/16".750 (19.1) 6 (152) 24 (610) 705-0188062-XX0012 3/16" X 1/16".750 (19.1) 12 (305) 48 (1219) 705-0188062-XX0018 3/16" X 1/16".750 (19.1) 18 (457) 72 (1829) 705-0188062-XX0024 3/16" X 1/16".750 (19.1) 24 (610) 96 (2439) 705-0250062-XX0003 1/4" X 1/8" 1.00 (25.4) 3 (76) 12 (305) 705-0250062-XX0006 1/4" X 1/8" 1.00 (25.4) 6 (152) 24 (610) 705-0250062-XX0012 1/4" X 1/8" 1.00 (25.4) 12 (305) 48 (1219) 705-0250062-XX0018 1/4" X 1/8" 1.00 (25.4) 18 (457) 72 (1829) 705-0250062-XX0024 1/4" X 1/8" 1.00 (25.4) 24 (610) 96 (2439) 705-0312062-XX0003 5/16" X 3/16" 1.625 (41.3) 3 (76) 12 (305) 705-0312062-XX0006 5/16" X 3/16" 1.625 (41.3) 6 (152) 24 (610) 705-0312062-XX0012 5/16" X 3/16" 1.625 (41.3) 12 (305) 48 (1219) 705-0312062-XX0018 5/16" X 3/16" 1.625 (41.3) 18 (457) 72 (1829) 705-0312062-XX0024 5/16" X 3/16" 1.625 (41.3) 24 (610) 96 (2439) 705-0375062-XX0003 3/8" X 1/4" 1.625 (41.3) 3 (76) 12 (305) 705-0375062-XX0006 3/8" X 1/4" 1.625 (41.3) 6 (152) 24 (610) 705-0375062-XX0012 3/8" X 1/4" 1.625 (41.3) 12 (305) 48 (1219) 705-0375062-XX0018 3/8" X 1/4" 1.625 (41.3) 18 (457) 72 (1829) 705-0375062-XX0024 3/8" X 1/4" 1.625 (41.3) 24 (610) 96 (2439) 705-0438062-XX0003 7/16" X 5/16" 3.00 (76.2) 3 (76) 12 (305) 705-0438062-XX0006 7/16" X 5/16" 3.00 (76.2) 6 (152) 24 (610) 705-0438062-XX0012 7/16" X 5/16" 3.00 (76.2) 12 (305) 48 (1219) 705-0500062-XX0003 1/2" X 3/8" 3.00 (76.2) 3 (76) 12 (305) 705-0500062-XX0006 1/2" X 3/8" 3.00 (76.2) 6 (152) 24 (610) 705-0500062-XX0012 1/2" X 3/8" 3.00 (76.2) 12 (305) 48 (1219) Standard left/right tail length is 6 inches. Please consult factory for pricing and delivery. Note: HP PFA Schedule 40 and 80 Pipe are available upon request. Please consult factory for price and delivery. 7

HP PFA Fluid Handling Tubing Dual Containment Tubing Part Number Line OD X ID Wall OD Wall Standard Packaging DUALCONHP 02500500LM Process Containment 1/4" X 5/32" X.047 1/2" X 3/8" X.062 ±.005 ±.005 ±.003 ±.003 300 ft. spool DUALCONHP 05000750LM Process Containment 1/2" X 3/8" X.062 3/4" X 5/8" X.062 ±.005 ±.006 ±.003 ±.003 300 ft. spool DUALCONHP 07501000LM Process Containment 3/4" X 5/8" X.062 1" X 7/8" X.062 Dual containment tubing provides long continuous lengths while reducing the number of connections and welding joints. The design utilizes a HP PFA inner process line for excellent chemical resistance. The FEP outer containment line provides clear visibility of the inner process line. Both process and containment lines are laser marked for traceability. Please consult the factory for pricing and delivery. Custom packaging, other resins and sizes, are quoted upon request. Contact the factory for more information. ±.005 ±.010 ±.003 ±.003 300 ft. spool 8

PFA Fluid Handling Tubing Product Overview s line of Fluoropolymer tubing is well suited for any corrosive or high purity application. PFA Tubing Products are available in several grades and sizes, and are offered in numerous lengths. PFA (Perfluoroalkoxy) is the material of choice in applications requiring excellent chemical resistance, high temperature exposure, clarity and long continuous lengths. s resin is a standard grade with a high molecular weight and high resistance to stress cracking. The tubing can be used with flare or conventional fittings, and is available in a wide range of sizes. Schedule 40 Pipe is also available. Features 100% virgin PFA resin used on all products. Translucent and flexible materials. Chemically inert to nearly all industrial chemicals and solvents. Smooth nonstick surface resulting in the lowest coefficient of friction. Low permeability. Nonflammable materials. FDA Compliant. Weather resistant. Benefits No process contamination. Excellent for flow monitoring systems. Longer product life and less downtime. Higher flow with no process contamination. Useful in severe chemical and gas service. Safety. Useful in food applications. Excellent for outdoor use in extreme conditions. Specifications Materials: Products in this catalog are manufactured using resins complying with ASTM D 3307 Specification. Flammability: Listed VW-1 by the Underwriters Laboratories, Inc. in their burning test classification for polymeric materials and passes the UL 83 vertical flame test. In a flame situation, PFA tubing resists combustion and does not promote flame spread. FDA Compliance: Most PFA resins qualify for use in contact with food in compliance with FDA regulation 21 CFR 177.1550. Pressure and Temperature Ranges: See pressure temperature chart or consult the factory. 400 350 300.062 wall Pressure vs. Temperature Chart Heavy Wall PFA Tubing Fractional Size 38 Media Temperature ( C) 65 93 121 149 176 1/4" 3/8" 1/2" 3/4" 1" 204 27.58 24.13 20.68 Pressure (PSIG) 250 200 150.047 wall.062 wall.047 wall.062 wall 17.24 13.79 10.34 Pressure (bar) 100.062 wall 6.90 50.062 wall 3.45 0 100 150 200 250 Media Temperature ( F) 300 350 400 9

PFA Fluid Handling Tubing Part numbers below are for standard configurations. For complete part numbers and options for material, color, packaging, etc. refer to Part Number Matrix on page 3. Industrial Wall Fractional Size Tubing OD Part Number OD X ID X Wall OD Wall Minimum Bend Radius Working PSIG (bar) Burst PSIG (bar) 3/32" 104-0094031-XXXXXX 3/32" X 1/32" X.031 ±.004 ±.003 1/2" 487 (33.6) 2,453 (169.1) 1/8" 104-0125031-XXXXXX 1/8" X 1/16" X.031 ±.004 ±.003 3/4" 369 (25.4) 1,859 (128.2) 5/32" 104-0156031-XXXXXX 5/32" X 3/32" X.031 ±.005 ±.003 1/2" 297 (20.5) 1,497 (103.2) 3/16" 104-0188031-XXXXXX 3/16" X 1/8" X.031 ±.005 ±.003 1/2" 249 (17.1) 1,253 (86.4) 1/4" 104-0250031-XXXXXX 1/4" X 3/16" X.031 ±.005 ±.003 1" 190 (13.1) 945 (65.2) 5/16" 104-0312031-XXXXXX 5/16" X 1/4" X.031 ±.005 ±.003 1-3/4" 150 (10.4) 758 (52.3) 3/8" 104-0375031-XXXXXX 3/8" X 5/16" X.031 ±.005 ±.003 2-1/2" 125 (8.6) 633 (43.6) 7/16" 104-0438031-XXXXXX 7/16" X 3/8" X.031 ±.005 ±.003 2" 108 (7.4) 543 (37.5) 1/2" 104-0500031-XXXXXX 1/2" X 7/16" X.031 ±.006 ±.003 4" 95 (6.6) 476 (32.8) 9/16" 104-0563031-XXXXXX 9/16" X 1/2" X.031 ±.006 ±.003 4-3/4" 84 (5.8) 424 (29.2) 5/8" 104-0625031-XXXXXX 5/8" X 9/16" X.031 ±.006 ±.003 6" 75 (5.2) 381 (26.7) 11/16" * 104-0688031-XXXXXX 11/16" X 5/8" X.031 ±.006 ±.003 6-3/4 69 (4.7) 347 (23.9) 3/4" * 104-0750032-XXXXXX 3/4" X 11/16" X.032 ±.006 ±.003 16" 68 (4.7) 318 (21.9).830 * 104-0830040-XXXXXX.830 X 3/4" X.040 ±.006 ±.003 N/A 76 (5.2) 381 (26.3).965 * 104-0965045-XXXXXX.965 X 7/8" X.045 ±.007 ±.003 N/A 73 (5.1) 369 (25.5) 1.10 * 104-1100050-XXXXXX 1.10 X 1" X.050 ±.007 ±.004 N/A 58 (4.0) 294 (20.3) Heavy Wall Fractional Size Tubing OD Part Number OD X ID X Wall OD Wall Minimum Bend Radius Working PSIG (bar) Burst PSIG (bar) 3/16' 104-0188062-XXXXXX 3/16" X 1/16" X.062 ±.005 ±.003 1/2" 492 (33.9) 2,478 (170.9) 1/4" 104-0250047-XXXXXX 104-0250062-XXXXXX 1/4" X 5/32"" X.047 1/4" X 1/8" X.062 ±.005 ±.003 3/4" 1/2" 286 (19.7) 380 (26.2) 1.443 (99.5) 1,889 (130.2) 5/16" 104-0312062-XXXXXX 5/16" X 3/16".062 ±.005 ±.003 1/2" 303 (20.9) 1,525 (105.2) 3/8" 104-0375062-XXXXXX 3/8" X 1/4" X.062 ±.005 ±.003 3/4" 260 (17.9) 1.280 (88.3) 7/16" 104-0438062-XXXXXX 7/16" X 5/16" X.062 ±.005 ±.003 1" 219 (15.1) 1,102 (76.0) 1/2" 104-0500062-XXXXXX 1/2" X 3/8" X.062 ±.006 ±.003 1-1/2" 195 (13.4) 968 (66.7) 9/16" 104-0563062-XXXXXX 9/16" X 7/16" X.062 ±.006 ±.003 2-1/2" 171 (11.8) 862 (59.5) 5/8" 104-0625062-XXXXXX 5/8" X 1/2" X.062 ±.006 ±.003 3" 160 (11.0) 778 (53.6) 11/16" 104-0688062-XXXXXX 11/16" X 9/16" X.062 ±.006 ±.003 5" 141 (9.7) 708 (48.8) 3/4" 104-0750062-XXXXXX 3/4" X 5/8" X.062 ±.006 ±.003 6" 132 (9.1) 650 (44.8) 7/8" 104-0875062-XXXXXX 7/8" X 3/4" X.062 ±.007 ±.003 12" 112 (7.7) 559 (38.5) 1" 104-1000062-XXXXXX 1" X 7/8" X.062 ±.010 ±.003 16" 100 (6.9) 490 (33.8) 1-1/8" * 104-1125062-XXXXXX 1-1/8" X 1' X.062 ±.015 ±.004 24" 87 (6.0) 436 (30.1) 1-1/4" * 104-1250062-XXXXXX 1-1/4" X 1-1/8" X.062 ±.015 ±.004 N/A 78 (5.4) 393 (27.1) 1-3/8" * 104-13750062-XXXXXX 1-3/8" X 1-1/4" X.062 ±.015 ±.004 N/A 71(4.9) 357 (24.6) 2-1/8" * 104-2125062-XXXXXX 2-1/8" X 2" X.062 ±.015 ±.004 N/A 46 (3.2) 232 (16.0) Pressures above are for operation at 73 F. Working pressure calculated using a Design Factor of 5. Note other manufacturers may use a Design Factor of 4. Fractional tubing is supplied in 25 ft. increments up to 1000 ft. continuous for sizes up to 1 OD. Standard packaging for sizes greater than 1 OD are 5 and 10 ft. straight lengths. Custom packaging and sizes are quoted upon request. * Non-Standard Product - Order Minimum Will Apply 10

PFA Fluid Handling Tubing Metric Size Tubing OD Part Number OD X ID X mm OD X ID X Inch OD / ID mm/inch Minimum Bend Radius 3 204-0300100-XXXXXX 3.0 X 1.0.118 X.039 ±.11 ±.004 N/A 4 204-0400100-XXXXXX 4.0 X 2.0.157 X.078 ±.11 ±.004 1/2" 5 204-0500100-XXXXXX 5.0 X 3.0.197 X.118 ±.11 ±.004 1/2" 6 204-0600100-XXXXXX 6.0 X 4.0.236 X.157 ±.13 ±.005 3/4" 7 204-0700100-XXXXXX 7.0 X 5.0.276 X.197 ±.13 ±.005 3/4" 8 204-0800100-XXXXXX 8.0 X 6.0.315 X.236 ±.13 ±.005 1" 9 204-0900100-XXXXXX 9.0 X 7.0.354 X.276 ±.13 ±.005 1-1/2" 10 204-1000100-XXXXXX 10.0 X 8.0.393 X.315 ±.13 ±.005 2" 12 204-1200100-XXXXXX 12.0 X 10.0.472 X.393 ±.15 ±.006 2-1/2" 14 * 204-1400100-XXXXXX 14.0 X 12.0.551 X.472 ±.15 ±.006 3-3/8" 16 * 204-1600100-XXXXXX 16.0 X 14.0.630 X.551 ±.15 ±.006 4-1/4" Consult factory for pressure ratings. Convoluted Tubing OPTION WITH FLARE NUT ASSEMBLY CONSULT FACTORY FOR PRICING Part Number OD "A" X ID "B" Nominal Wall Bend Radius Pitch "C" 304-0375020-XXXXXX 3/8" X 1/4".020 1/2" 8 304-0500023-XXXXXX 1/2" X 3/8".023 3/4" 8 304-0750025-XXXXXX 3/4" X 5/8".025 1-1/2" 8 304-1000025-XXXXXX 1" X 7/8".025 2-1/2" 6 Convoluted tubing is used in applications where smaller bend diameters are required. Convoluted tubing is made to order. Custom sizes, colors, packaging, and PTFE liners are also available. Please consult factory. * Non-Standard Product - Order Minimum Will Apply 11

PFA Fluid Handling Tubing Retractable Coils Left Length A Right Length Part Number OD X ID Coil ID Inch (mm) Retracted Length "A" Inch (mm) Extended Length Inch (mm) 704-0188062-XX0003 3/16" X 1/16".750 (19.1) 3 (76) 12 (305) 704-0188062-XX0006 3/16" X 1/16".750 (19.1) 6 (152) 24 (610) 704-0188062-XX0012 3/16" X 1/16".750 (19.1) 12 (305) 48 (1219) 704-0188062-XX0018 3/16" X 1/16".750 (19.1) 18 (457) 72 (1829) 704-0188062-XX0024 3/16" X 1/16".750 (19.1) 24 (610) 96 (2439) 704-0250062-XX0003 1/4" X 1/8" 1.00 (25.4) 3 (76) 12 (305) 704-0250062-XX0006 1/4" X 1/8" 1.00 (25.4) 6 (152) 24 (610) 704-0250062-XX0012 1/4" X 1/8" 1.00 (25.4) 12 (305) 48 (1219) 704-0250062-XX0018 1/4" X 1/8" 1.00 (25.4) 18 (457) 72 (1829) 704-0250062-XX0024 1/4" X 1/8" 1.00 (25.4) 24 (610) 96 (2439) 704-0312062-XX0003 5/16" X 3/16" 1.625 (41.3) 3 (76) 12 (305) 704-0312062-XX0006 5/16" X 3/16" 1.625 (41.3) 6 (152) 24 (610) 704-0312062-XX0012 5/16" X 3/16" 1.625 (41.3) 12 (305) 48 (1219) 704-0312062-XX0018 5/16" X 3/16" 1.625 (41.3) 18 (457) 72 (1829) 704-0312062-XX0024 5/16" X 3/16" 1.625 (41.3) 24 (610) 96 (2439) 704-0375062-XX0003 3/8" X 1/4" 1.625 (41.3) 3 (76) 12 (305) 704-0375062-XX0006 3/8" X 1/4" 1.625 (41.3) 6 (152) 24 (610) 704-0375062-XX0012 3/8" X 1/4" 1.625 (41.3) 12 (305) 48 (1219) 704-0375062-XX0015 3/8" X 1/4" 1.625 (41.3) 15 (381) 60 (1524) 704-0375062-XX0018 3/8" X 1/4" 1.625 (41.3) 18 (457) 72 (1829) 704-0375062-XX0024 3/8" X 1/4" 1.625 (41.3) 24 (610) 96 (2439) 704-0438062-XX0003 7/16" X 5/16" 3.00 (76.2) 3 (76) 12 (305) 704-0438062-XX0006 7/16" X 5/16" 3.00 (76.2) 6 (152) 24 (610) 704-0438062-XX0012 7/16" X 5/16" 3.00 (76.2) 12 (305) 48 (1219) 704-0500062-XX0003 1/2" X 3/8" 3.00 (76.2) 3 (76) 12 (305) 704-0500062-XX0006 1/2" X 3/8" 3.00 (76.2) 6 (152) 24 (610) 704-0500062-XX0012 1/2" X 3/8" 3.00 (76.2) 12 (305) 48 (1219) Standard left/right tail length is 6 inches. Please consult factory for pricing and delivery. Note: PFA Schedule 40 and 80 Pipe are available upon request. Please consult factory for price and delivery. 12

FEP Fluid Handling Tubing Product Overview s line of FEP (Fluorinated Ethylene Propylene) tubing exhibits the highest clarity offered. This clarity makes this tubing ideal for flow monitoring applications. FEP also uses a high molecular weight resin that has the best stress crack resistance. It is also widely used in water purification systems due to its excellent transmission of UV light. FEP resin meets the FDA requirements for repeated food contact. The product is available in various sizes of tubing and pipe. Features 100% virgin FEP resin used on all products. Most translucent Fluoropolymer available. Chemically inert to nearly all industrial chemicals and solvents. High abrasion resistance and thermal stability. Low permeability. Nonflammable materials. FDA Compliant. Benefits Highest quality products. Excellent for flow monitoring applications. Longer product life and less downtime. Useful in applications requiring thermal cycling. Useful in severe chemical and gas service. Safety. Useful in food applications. Specifications Materials: FEP products in this catalog are manufactured using resins complying with ASTM D 3296-98 Specification. Flammability: Listed VW-1 by the Underwriters Laboratories, Inc. in their burning test classification for polymeric materials and passes the UL 83 vertical flame test. In a flame situation, FEP tubing resists combustion and does not promote flame spread. FDA Compliance: Most FEP resins qualify for use in contact with food in compliance with FDA regulation 21 CFR 177.1550. Temperature Ranges: Pressure temperature information is available from the factory upon request. 13

FEP Fluid Handling Tubing Part numbers below are for standard configurations. For complete part numbers and options for material, color, packaging, etc. refer to Part Number Matrix on page 3. Industrial Wall Fractional Size Tubing OD Part Number OD X ID X Wall OD Wall Minimum Bend Radius Working PSIG (bar) Burst PSIG (bar) 3/32" 103-0094031-XXXXXX 3/32" X 1/32" X.031 ±.004 ±.003 1/2" 389 (26.8) 1,962 (135.3) 1/8" 103-0125031-XXXXXX 1/8" X 1/16" X.031 ±.004 ±.003 3/4" 295 (20.3) 1,487 (102.5) 5/32" 103-0156031-XXXXXX 5/32" X 3/32" X.031 ±.005 ±.003 1/2" 238 (16.4) 1,197 (82.6) 3/16" 103-0188031-XXXXXX 3/16" X 1/8" X.031 ±.005 ±.003 1/2" 199 (13.7) 1,002 (69.1) 1/4" 103-0250031-XXXXXX 1/4" X 3/16" X.031 ±.005 ±.003 1" 150 (10.3) 756 (52.1) 5/16" 103-0312031-XXXXXX 5/16" X 1/4" X.031 ±.005 ±.003 1-3/4" 120 (8.3) 606 (41.8) 3/8" 103-0375031-XXXXXX 3/8" X 5/16" X.031 ±.005 ±.003 2-1/2" 100 (6.9) 506 (34.9) 7/16" 103-0438031-XXXXXX 7/16" X 3/8" X.031 ±.005 ±.003 2" 86 (5.9) 435 (30.0) 1/2" 103-0500031-XXXXXX 1/2" X 7/16" X.031 ±.006 ±.003 4" 75 (5.2) 381 (26.3) 9/16" 103-0563031-XXXXXX 9/16" X 1/2" X.031 ±.006 ±.003 4-3/4" 67 (4.6) 339 (23.4) 5/8" 103-0625031-XXXXXX 5/8" X 9/16" X.031 ±.006 ±.003 6" 60 (4.1) 305 (21.0) 11/16" * 103-0688031-XXXXXX 11/16" X 5/8" X.031 ±.006 ±.003 6-3/4 55 (3.8) 278 (19.1) 3/4" * 103-0750032-XXXXXX 3/4" X 11/16" X.032 ±.006 ±.003 16" 54 (3.7) 255 (17.6).830 * 103-0830040-XXXXXX.830 X 3/4" X.040 ±.006 ±.003 N/A 61 (4.2) 305 (21.0).965 * 103-0965045-XXXXXX.965 X 7/8" X.045 ±.007 ±.003 N/A 59 (4.0) 295 (20.4) 1.10 * 103-1100050-XXXXXX 1.10 X 1" X.050 ±.010 ±.004 N/A 47 (3.2) 235 (16.2) Heavy Wall Fractional Size Tubing OD Part Number OD X ID X Wall OD Wall Minimum Bend Radius Working PSIG (bar) Burst PSIG (bar) 3/16' 103-0188062-XXXXXX 3/16" X 1/16" X.062 ±.005 ±.003 1/2" 393 (27.1) 1,983 (136.7) 1/4" 103-0250047-XXXXXX 103-0250062-XXXXXX 1/4" X 5/32"" X.047 1/4" X 1/8" X.062 ±.005 ±.003 3/4" 1/2" 229 (15.8) 300 (20.7) 1,154 (79.6) 1,511 (104.2) 5/16" 103-0312062-XXXXXX 5/16" X 3/16".062 ±.005 ±.003 1/2" 242 (16.7) 1,220 (84.1) 3/8" 103-0375062-XXXXXX 3/8" X 1/4" X.062 ±.005 ±.003 3/4" 210 (14.5) 1,024 (70.6) 7/16" 103-0438062-XXXXXX 7/16" X 5/16" X.062 ±.005 ±.003 1" 175 (12.1) 882 (60.8) 1/2" 103-0500062-XXXXXX 1/2" X 3/8" X.062 ±.005 ±.003 1-1/2" 160 (11.0) 774 (53.4) 9/16" 103-0563062-XXXXXX 9/16" X 7/16" X.062 ±.006 ±.003 2-1/2" 137 (9.4) 690 (47.6) 5/8" 103-0625062-XXXXXX 5/8" X 1/2" X.062 ±.006 ±.003 3" 125 (8.6) 622 (42.9) 11/16" 103-0688062-XXXXXX 11/16" X 9/16" X.062 ±.006 ±.003 5" 112 (7.8) 567 (39.1) 3/4" 103-0750062-XXXXXX 3/4" X 5/8" X.062 ±.006 ±.003 6" 105 (7.2) 520 (35.9) 7/8" 103-0875062-XXXXXX 7/8" X 3/4" X.062 ±.007 ±.003 12" 90 (6.2) 447 (30.8) 1" 103-1000062-XXXXXX 1" X 7/8" X.062 ±.010 ±.003 16" 80 (5.5) 392 (27.0) 1-1/8" * 103-1125062-XXXXXX 1-1/8" X 1' X.062 ±.015 ±.003 24" 69 (4.8) 349 (24.0) 1-1/4" * 103-1250062-XXXXXX 1-1/4" X 1-1/8" X.062 ±.015 ±.004 N/A 62 (4.3) 314 (21.7) 1-3/8" * 103-13750062-XXXXXX 1-3/8" X 1-1/4" X.062 ±.015 ±.004 N/A 57(3.9) 286 (19.7) 2-1/8" * 103-2125062-XXXXXX 2-1/8" X 2" X.062 ±.015 ±.004 N/A 37 (2.5) 186 (12.8) Pressures above are for operation at 73 F. Working pressure calculated using a Design Factor of 5. Note other manufacturers may use a Design Factor of 4. Fractional tubing is supplied in 25 ft. increments up to 1000 ft. continuous for sizes up to 1 OD. Standard packaging for sizes greater than 1 OD are 5 and 10 ft. straight lengths. Custom packaging and sizes are quoted upon request. * Non-Standard Product - Order Minimum Will Apply 14

FEP Fluid Handling Tubing Metric Tubing OD Part Number OD X ID X mm OD X ID X Inch OD / ID mm/inch Minimum Bend Radius 3 203-0300100-XXXXXX 3.0 X 1.0.118 X.039 ±.11 ±.004 N/A 4 203-0400100-XXXXXX 4.0 X 2.0.157 X.078 ±.11 ±.004 1/2" 5 203-0500100-XXXXXX 5.0 X 3.0.197 X.118 ±.11 ±.004 1/2" 6 203-0600100-XXXXXX 6.0 X 4.0.236 X.157 ±.13 ±.005 3/4" 7 203-0700100-XXXXXX 7.0 X 5.0.276 X.197 ±.13 ±.005 3/4" 8 203-0800100-XXXXXX 8.0 X 6.0.315 X.236 ±.13 ±.005 1" 9 203-0900100-XXXXXX 9.0 X 7.0.354 X.276 ±.13 ±.005 1-1/2" 10 203-1000100-XXXXXX 10.0 X 8.0.393 X.315 ±.13 ±.005 2" 12 203-1200100-XXXXXX 12.0 X 10.0.472 X.393 ±.15 ±.006 2-1/2" 14 * 203-1400100-XXXXXX 14.0 X 12.0.551 X.472 ±.15 ±.006 3-3/8" 16 * 203-1600100-XXXXXX 16.0 X 14.0.630 X.551 ±.15 ±.006 4-1/4" Consult factory for pressure ratings. Convoluted Tubing OPTION WITH FLARE NUT ASSEMBLY CONSULT FACTORY FOR PRICING Part Number OD "A" X ID "B" Nominal Wall Bend Radius Pitch "C" 303-0375020-XXXXXX 3/8" X 1/4".020 1/2" 8 303-0500023-XXXXXX 1/2" X 3/8".023 3/4" 8 303-0750025-XXXXXX 3/4" X 5/8".025 1-1/2" 8 303-1000025-XXXXXX 1" X 7/8".025 2-1/2" 6 Convoluted tubing is used in applications where smaller bend diameters are required. Convoluted tubing is made to order. Custom sizes, colors, packaging, and PTFE liners are quoted upon request. * Non-Standard Product - Order Minimum Will Apply 15

FEP Fluid Handling Tubing Retractable Coils Left Length A Right Length Part Number OD X ID Coil ID Inch (mm) Retracted Length "A" Inch (mm) Extended Length Inch (mm) 703-0188062-XX0003 3/16" X 1/16".750 (19.1) 3 (76) 12 (305) 703-0188062-XX0006 3/16" X 1/16".750 (19.1) 6 (152) 24 (610) 703-0188062-XX0012 3/16" X 1/16".750 (19.1) 12 (305) 48 (1219) 703-0188062-XX0018 3/16" X 1/16".750 (19.1) 18 (457) 72 (1829) 703-0250062-XX0003 1/4" X 1/8" 1.00 (25.4) 3 (76) 12 (305) 703-0250062-XX0006 1/4" X 1/8" 1.00 (25.4) 6 (152) 24 (610) 703-0250062-XX0012 1/4" X 1/8" 1.00 (25.4) 12 (305) 48 (1219) 703-0250062-XX0018 1/4" X 1/8" 1.00 (25.4) 18 (457) 72 (1829) 703-0312062-XX0003 5/16" X 3/16" 1.625 (41.3) 3 (76) 12 (305) 703-0312062-XX0006 5/16" X 3/16" 1.625 (41.3) 6 (152) 24 (610) 703-0312062-XX0012 5/16" X 3/16" 1.625 (41.3) 12 (305) 48 (1219) 703-0312062-XX0018 5/16" X 3/16" 1.625 (41.3) 18 (457) 72 (1829) 703-0375062-XX0003 3/8" X 1/4" 1.625 (41.3) 3 (76) 12 (305) 703-0375062-XX0006 3/8" X 1/4" 1.625 (41.3) 6 (152) 24 (610) 703-0375062-XX0012 3/8" X 1/4" 1.625 (41.3) 12 (305) 48 (1219) 703-0375062-XX0015 3/8" X 1/4" 1.625 (41.3) 15 (381) 60 (1524) 703-0375062-XX0018 3/8" X 1/4" 1.625 (41.3) 18 (457) 72 (1829) 703-0438062-XX0003 7/16" X 5/16" 3.00 (76.2) 3 (76) 12 (305) 703-0438062-XX0006 7/16" X 5/16" 3.00 (76.2) 6 (152) 24 (610) 703-0438062-XX0012 7/16" X 5/16" 3.00 (76.2) 12 (305) 48 (1219) 703-0500062-XX0003 1/2" X 3/8" 3.00 (76.2) 3 (76) 12 (305) 703-0500062-XX0006 1/2" X 3/8" 3.00 (76.2) 6 (152) 24 (610) 703-0500062-XX0012 1/2" X 3/8" 3.00 (76.2) 12 (305) 48 (1219) Standard left/right tail length is 6 inches. Please consult factory for pricing and delivery. Note: FEP Schedule 40 and 80 Pipe are available upon request. Please consult factory for price and delivery. 16

PTFE Fluid Handling Tubing Product Overview s line of PTFE (Polytetrafluoroethylene) tubing is the most flexible product offered. PTFE tubing resists corrosive liquids and gases, and has the broadest temperature range of all Fluoropolymer products. The tubing has a smooth non-stick surface with low permeability. Features 100% virgin PTFE resin used on all products. Most flexible Fluoropolymer available. Chemically inert to nearly all industrial chemicals and solvents. Smooth nonstick surface resulting in the lowest coefficient of friction. Low permeability. Nonflammable materials. FDA Compliant. Excellent electrical properties. Benefits Highest quality products. Longer lasting. Longer product life and less downtime. Higher abrasion resistance with no process contamination. Useful in severe chemical and gas service. Safety. Useful in food applications. Useful in insulation applications. Specifications Materials: PTFE Products in this catalog are manufactured using resins complying with ASTM D 3295 Specification. Flammability: Listed VW-1 by the Underwriters Laboratories, Inc. in their burning test classification for polymeric materials and passes the UL 83 vertical flame test. In a flame situation, PTFE tubing resists combustion and does not promote flame spread. FDA Compliance: All PTFE resins qualify for use in contact with food in compliance with FDA regulation 21 CFR 177.1550. Temperature Ranges: Pressure temperature information is available from the factory upon request. 17

PTFE Fluid Handling Tubing Part numbers below are for standard configurations. For complete part numbers and options for material, color, packaging, etc. refer to Part Number Matrix on page 3. Industrial Wall Fractional Size Tubing OD Part Number OD X ID X Wall OD Wall Minimum Bend Radius Working PSIG (bar) Burst PSIG (bar) 3/32" 101-0094031-XXXXXX 3/32" X 1/32" X.031 ±.004 ±.003 1/2" 389 (26.8) 1,962 (135.3) 1/8" 101-0125031-XXXXXX 1/8" X 1/16" X.031 ±.004 ±.003 3/4" 295 (20.3) 1,487 (102.5) 5/32" 101-0156031-XXXXXX 5/32" X 3/32" X.031 ±.005 ±.003 1/2" 238 (16.4) 1,197 (82.6) 3/16" 101-0188031-XXXXXX 3/16" X 1/8" X.031 ±.005 ±.003 1/2" 199 (13.7) 1,002 (69.1) 1/4" 101-0250031-XXXXXX 1/4" X 3/16" X.031 ±.005 ±.003 1" 150 (10.3) 756 (52.1) 5/16" 101-0312031-XXXXXX 5/16" X 1/4" X.031 ±.005 ±.003 1-3/4" 120 (8.3) 606 (41.8) 3/8" 101-0375031-XXXXXX 3/8" X 5/16" X.031 ±.005 ±.003 2-1/2" 100 (6.9) 506 (34.9) 7/16" 101-0438031-XXXXXX 7/16" X 3/8" X.031 ±.005 ±.003 2" 86 (5.9) 435 (30.0) 1/2" 101-0500031-XXXXXX 1/2" X 7/16" X.031 ±.006 ±.003 4" 75 (5.2) 381 (26.3) 9/16" 101-0563031-XXXXXX 9/16" X 1/2" X.031 ±.006 ±.003 4-3/4" 67 (4.6) 339 (23.4) 5/8" 101-0625031-XXXXXX 5/8" X 9/16" X.031 ±.006 ±.003 6" 60 (4.1) 305 (21.0) 11/16" 101-0688031-XXXXXX 11/16" X 5/8" X.031 ±.006 ±.003 6-3/4 55 (3.8) 278 (19.1) 3/4" 101-0750032-XXXXXX 3/4" X 11/16" X.032 ±.006 ±.003 16" 50 (3.4) 255 (17.6).830 101-0830040-XXXXXX.830 X 3/4" X.040 ±.006 ±.003 N/A 61 (4.2) 305 (21.7).965 101-0965045-XXXXXX.965 X 7/8" X.045 ±.007 ±.003 N/A 59 (4.0) 295 (20.4) 1.10 101-1100050-XXXXXX 1.10 X 1" X.050 ±.010 ±.004 N/A 47 (3.2) 235 (16.7) Heavy Wall Fractional Size Tubing OD Part Number OD X ID X Wall OD Wall Minimum Bend Radius Working PSIG (bar) Burst PSIG (bar) 3/16' 101-0188062-XXXXXX 3/16" X 1/16" X.062 ±.005 ±.003 1/2" 393 (27.1) 1,983 (136.7) 1/4" 101-0250047-XXXXXX 101-0250062-XXXXXX 1/4" X 5/32"" X.047 1/4" X 1/8" X.062 ±.005 ±.003 3/4" 1/2" 229 (15.8) 300 (20.7) 1.154 (79.6) 1,511 (104.2) 5/16" 101-0312062-XXXXXX 5/16" X 3/16".062 ±.005 ±.003 1/2" 242 (16.7) 1,220 (84.1) 3/8" 101-0375062-XXXXXX 3/8" X 1/4" X.062 ±.005 ±.003 3/4" 200 (13.8) 1,024 (70.6) 7/16" 101-0438062-XXXXXX 7/16" X 5/16" X.062 ±.005 ±.003 1" 175 (12.1) 882 (60.8) 1/2" 101-0500062-XXXXXX 1/2" X 3/8" X.062 ±.005 ±.003 1-1/2" 150 (10.3) 774 (53.4) 9/16" 101-0563062-XXXXXX 9/16" X 7/16" X.062 ±.006 ±.003 2-1/2" 137 (9.4) 690 (47.6) 5/8" 101-0625062-XXXXXX 5/8" X 1/2" X.062 ±.006 ±.003 3" 125 (8.6) 622 (42.9) 11/16" 101-0688062-XXXXXX 11/16" X 9/16" X.062 ±.006 ±.003 5" 112 (7.8) 567 (39.1) 3/4" 101-0750062-XXXXXX 3/4" X 5/8" X.062 ±.006 ±.003 6" 100 (6.9) 520 (35.9) 7/8" 101-0875062-XXXXXX 7/8" X 3/4" X.062 ±.007 ±.003 12" 90 (6.2) 447 (30.8) 1" 101-1000062-XXXXXX 1" X 7/8" X.062 ±.010 ±.003 16" 80 (5.5) 392 (27.0) Pressures above are for operation at 73 F. Working pressure calculated using a Design Factor of 5. Note other manufacturers may use a Design Factor of 4. Fractional tubing for sizes up to 1 OD is supplied in random length coils with a minimum coil length of 15 feet and a maximum of 3 pieces per 100 feet. Sizes over 1 OD are supplied in 5 or 10 foot straight lengths. Custom packaging and sizes are quoted upon request. 18

PTFE Fluid Handling Tubing Metric Size Tubing OD Part Number OD X ID X mm OD X ID X Inch OD / ID mm/inch Minimum Bend Radius 3 201-0300100-XXXXXX 3.0 X 1.0.118 X.039 ±.11 ±.004 1-1/2" 4 201-0400100-XXXXXX 4.0 X 2.0.157 X.078 ±.11 ±.004 1-1/2" 5 201-0500100-XXXXXX 5.0 X 3.0.197 X.118 ±.11 ±.004 1-3/4" 6 201-0600100-XXXXXX 6.0 X 4.0.236 X.157 ±.13 ±.005 1-3/4" 7 201-0700100-XXXXXX 7.0 X 5.0.276 X.197 ±.13 ±.005 2" 8 201-0800100-XXXXXX 8.0 X 6.0.315 X.236 ±.13 ±.005 2-1/2" 9 201-0900100-XXXXXX 9.0 X 7.0.354 X.276 ±.13 ±.005 2-1/2" 10 201-1000100-XXXXXX 10.0 X 8.0.393 X.315 ±.13 ±.005 2-1/2" 12 201-1200100-XXXXXX 12.0 X 10.0.472 X.393 ±.15 ±.006 4" 14 201-1400100-XXXXXX 14.0 X 12.0.551 X.472 ±.15 ±.006 6" 16 201-1600100-XXXXXX 16.0 X 14.0.630 X.551 ±.15 ±.006 12" Consult factory for pressure ratings. Metric tubing is supplied in random coils with a minimum coil length of 15 feet and a maximum of 3 pieces per 100 feet. Convoluted Tubing Part Number OD "A" X ID "B" Wall "C" Cuff OD "D" Cuff Length "E" Bend Radius Pitch "F" 301-0320023-XXXXXX.320 X.181.023.280 3/4" 1/2" 8 301-0450027-XXXXXX.450 X.303.027.415 1" 7/8" 7 301-0590029-XXXXXX.590 X.425.029.540 1" 1-1/4" 6 301-0660029-XXXXXX.660 X.485.029.673 1-1/4" 1-1/2" 6 301-0780035-XXXXXX.780 X.608.035.800 1-1/2" 1-3/4" 6 301-1100035-XXXXXX 1.100 X.850.035 1.060 2" 2-1/4" 4-1/2 301-1390035-XXXXXX 1.390 X 1.105.035 1.310 2-1/2" 2-3/4" 4 301-1539035-XXXXXX * 1.539 X 1.210.035 1.560 2-1/2" 3" 4 301-2100040-XXXXXX * 2.100 X 1.690.040 2.080 2-1/2" 3" 4 Convoluted tubing is made to order. PTFE convoluted tubing is provided without cuffs direct from inventory and custom cuffs are quoted upon request. Stock packaging is random coils. Specifications: MIL-T-81914/1; additional sizes including /2, Class 1 & 2 also available. * Non-Standard Product - Order Minimum Will Apply 19

PVDF Fluid Handling Tubing Product Overview PVDF (Polyvinylidene Fluoride) is a tough engineering Fluoropolymer that offers a combination of properties beneficial for use in many critical applications requiring chemical resistance with low permeability. PVDF exhibits low extractable levels, while providing high mechanical strength, excellent abrasion resistance, and good resistance to many chemicals and solvents. Atlantic s PVDF tubing is excellent for use in ultra pure water systems and for ground water monitoring. Features 100% virgin PVDF resin used on all products. Good chemical resistance. Low permeability. Weather resistant. UV and radiation resistance. High abrasion resistance and thermal stability. FDA Compliant. Benefits No process contamination. Useful in most applications with long cycle life. Useful in severe chemical and gas applications. Excellent for outdoor use under extreme conditions. Useful in severe applications. Useful in thermal cycling applications. Useful in food applications. Specifications Materials: Products in this catalog are manufactured using resins complying with ASTM D 3222 Specification. Flammability: Listed 94-VO rated by the Underwriters Laboratories, Inc. in their burning test classification for polymeric materials and passes the UL 83 vertical flame test. In a flame situation, PVDF tubing resists combustion and does not promote flame spread. FDA Compliance: Most PVDF resins qualify for use in contact with food in compliance with FDA regulation 21 CFR 177.1500. Temperature Ranges: Pressure temperature information is available from the factory upon request. 20

PVDF Fluid Handling Tubing Part numbers below are for standard configurations. For complete part numbers and options for material, color, packaging, etc. refer to Part Number Matrix on page 3. Industrial Wall Fractional Tubing OD Part Number OD X ID X Wall OD Wall Minimum Bend Radius Working PSIG (bar) Burst PSIG (bar) 1/8" 110-0125031-XXXXXX 1/8" X 1/16" X.031 ±.004 ±.003 1/2" 267 (18.4) 1,348 (92.9) 3/16" 110-0188031-XXXXXX 3/16" X 1/8" X.031 ±.005 ±.003 3/4" 180 (12.4) 908 (62.6) 1/4" 110-0250031-XXXXXX 1/4" X 3/16" X.031 ±.005 ±.003 1" 170 (11.7) 685 (47.2) 5/16" 110-0312031-XXXXXX 5/16" X 1/4" X.031 ±.005 ±.003 1-3/4" 109 (7.5) 550 (37.9) 3/8" 110-0375031-XXXXXX 3/8" X 5/16" X.031 ±.005 ±.003 3-3/4" 111 (7.6) 459 (31.6) 7/16" 110-0438031-XXXXXX 7/16" X 3/8" X.031 ±.005 ±.003 5" 78 (5.4) 394 (27.2) 1/2" 110-0500031-XXXXXX 1/2" X 7/16" X.031 ±.006 ±.003 6" 83 (5.7) 345 (23.8) 9/16" * 110-0563031-XXXXXX 9/16" X 1/2" X.031 ±.006 ±.003 7" 61 (4.2) 307 (21.2) Heavy Wall Fractional Tubing OD Part Number OD X ID X Wall OD Wall Minimum Bend Radius Working PSIG (bar) Burst PSIG (bar) 1/4" 110-0250047-XXXXXX 110-0250062-XXXXXX 1/4" X 5/32"" X.047 1/4" X 1/8" X.062 ±.005 ±.003 3/4" 1/2" 208 (14.3) 330 (22.7) 1,046 (72.1) 1,369 (94.4) 5/16" 110-0312062-XXXXXX 5/16" X 3/16".062 ±.005 ±.003 1/2" 219 (15.1) 1,106 (76.3) 3/8" 110-0375062-XXXXXX 3/8" X 1/4" X.062 ±.005 ±.003 1-1/2" 224 (15.4) 928 (64.0) 1/2" 110-0500062-XXXXXX 1/2" X 3/8" X.062 ±.005 ±.003 3" 169 (11.7) 701 (48.3) 5/8" 110-0625062-XXXXXX 5/8" X 1/2" X.062 ±.006 ±.003 4-1/2" 136 (9.4) 564 (38.9) 3/4" 110-0750062-XXXXXX 3/4" X 5/8" X.062 ±.006 ±.003 9" 114 (7.9) 472 (32.5) 1" 110-1000062-XXXXXX 1" X 7/8" X.062 ±.010 ±.003 24" 86 (5.9) 355 (24.5) 1-1/8" * 110-1125062-XXXXXX 1-1/8" X 1' X.062 ±.015 ±.003 35" 63 (4.3) 316 (21.8) Pressures above are for operation at 73 F. Working pressure calculated using a Design Factor of 5. Note other manufacturers may use a Design Factor of 4. Fractional tubing is supplied in 25 ft. increments up to 1000 ft. continuous for sizes up to 1 OD. Standard packaging for sizes greater than 1 OD are 5 and 10 ft. straight lengths. Custom packaging and sizes are quoted upon request. Metric Tubing OD Part Number OD X ID X mm OD X ID X Inch Consult factory for pressure ratings. Consult factory for pricing and delivery. Note: PVDF Pipe and Convoluted Tubing are available upon request. Please consult factory for price and availability. 21 OD / ID mm/inch Minimum Bend Radius 3 210-0300100-XXXXXX 3.0 X 1.0.118 X.039 ±.11 ±.004 N/A 4 210-0400100-XXXXXX 4.0 X 2.0.157 X.078 ±.11 ±.004 1/2" 5 210-0500100-XXXXXX 5.0 X 3.0.197 X.118 ±.11 ±.004 1/2" 6 210-0600100-XXXXXX 6.0 X 4.0.236 X.157 ±.13 ±.005 3/4" 7 210-0700100-XXXXXX 7.0 X 5.0.276 X.197 ±.13 ±.005 1" 8 210-0800100-XXXXXX 8.0 X 6.0.315 X.236 ±.13 ±.005 1-1/2" 9 210-0900100-XXXXXX 9.0 X 7.0.354 X.276 ±.13 ±.005 2-1/2" 10 210-1000100-XXXXXX 10.0 X 8.0.393 X.315 ±.13 ±.005 3" 12 210-1200100-XXXXXX 12.0 X 10.0.472 X.393 ±.15 ±.006 4" 14 * 210-1400100-XXXXXX 14.0 X 12.0.551 X.472 ±.15 ±.006 5-1/2" * Non-Standard Product - Order Minimum Will Apply

Parker Safety Guide! Parker Safety Guide for Selecting and Using Hose, Tubing, Fittings, and Related Accessories Parker Publication No. 4400-B.1 Revised: May 2002 WARNING: Failure or improper selection or improper use of hose, tubing, fittings, assemblies or related accessories ( Products ) can cause death, personal injury and property damage. Possible consequences of failure or improper selection or improper use of these Products include but are not limited to: Fittings thrown off at high speed. High velocity fluid discharge. Explosion or burning of the conveyed fluid. Electrocution from high voltage electric power lines. Contact with suddenly moving or falling objects that are controlled by the conveyed fluid. Injections by high-pressure fluid discharge. Dangerously whipping Hose. Contact with conveyed fluids that may be hot, cold, toxic or otherwise injurious. Sparking or explosion caused by static electricity buildup or other sources of electricity. Sparking or explosion while spraying paint or flammable liquids. Injuries resulting from inhalation, ingestion or exposure to fluids. Before selecting or using any of these Products, it is important that you read and follow the instructions below. Only Hose from Parker s Stratoflex Products Division is approved for in flight aerospace applications, and no other Hose can be used for such in flight applications. 1.0 GENERAL INSTRUCTIONS 1.1 Scope: This safety guide provides instructions for selecting and using (including assembling, installing, and maintaining) these Products. For convenience, all rubber and/or thermoplastic products commonly called hose or tubing are called Hose in this safety guide. All assemblies made with Hose are called Hose Assemblies. All products commonly called fittings or couplings are called Fittings. All related accessories (including crimping and swaging machines and tooling) are called Related Accessories. This safety guide is a supplement to and is to be used with, the specific Parker publications for the specific Hose, Fittings and Related Accessories that are being considered for use. 1.2 Fail-Safe: Hose, and Hose Assemblies and Fittings can and do fail without warning for many reasons. Design all systems and equipment in a fail-safe mode, so that failure of the Hose or Hose Assembly or Fitting will not endanger persons or property. 1.3 Distribution: Provide a copy of this safety guide to each person that is responsible for selecting or using Hose and Fitting products. Do not select or use Parker Hose or Fittings without thoroughly reading and understanding this safety guide as well as the specific Parker publications for the products considered or selected. 1.4 User Responsibility: Due to the wide variety of operating conditions and applications for Hose and Fittings, Parker and its distributors do not represent or warrant that any particular Hose or Fitting is suitable for any specific end use system. This safety guide does not analyze all technical parameters that must be considered in selecting a product. The user, through its own analysis and testing, is solely responsible for: Making the final selection of the Hose and Fitting. Assuring that the user s requirements are met and that the application presents no health or safety hazards. Providing all appropriate health and safety warnings on the equipment on which the Hose and Fittings are used. Assuring compliance with all applicable government and industry standards. 1.5 Additional Questions: Call the appropriate Parker technical service department if you have any questions or require any additional information. See the Parker publication for the product being considered or used, or call 1-800-CPARKER, or go to www.parker.com, for telephone numbers of the appropriate technical service department. 2.0 HOSE AND FITTING SELECTION INSTRUCTIONS 2.1 Electrical Conductivity: Certain applications require that the Hose be nonconductive to prevent electrical current flow. Other applications require the Hose and the Fitting and the Hose/Fitting interface to be sufficiently conductive to drain off static electricity. Extreme care must be exercised when selecting Hose and Fittings for these or any other applications in which electrical conductivity or nonconductivity is a factor. The electrical conductivity or nonconductivity of Hose and Fittings is dependent upon many factors and may be susceptible to change. These factors include but are not limited to the various materials used to make the Hose and the Fittings, Fitting finish (some Fitting finishes are electrically conductive while others are nonconductive), manufacturing methods (including moisture control), how the Fittings contact the Hose, age and amount of deterioration or damage or other changes, moisture content of the Hose at any particular time, and other factors. The following are considerations for electrically nonconductive and conductive Hose. For other applications consult the individual catalog pages and the appropriate industry or regulatory standards for proper selection. 2.1.1 Electrically Nonconductive Hose: Certain applications require that the Hose be nonconductive to prevent electrical current flow or to maintain electrical isolation. For these applications that require Hose to be electrically nonconductive, including but not limited to applications near high voltage electric lines, only special nonconductive Hose can be used. The manufacturer of the equipment in which the nonconductive Hose is to be used must be consulted to be certain that the Hose and Fittings that are selected are proper for the application. Do not use any Parker Hose or Fitting for any such application requiring nonconductive Hose, including but not limited to applications near high voltage electric lines, unless (i) the application is expressly approved in the Parker technical publication for the product, (ii) the Hose is marked nonconductive, and (iii) the manufacturer of the equipment on which the Hose is to be used specifically approves the particular Parker Hose and Fitting for such use. 2.1.2 Electrically Conductive Hose: Parker manufacturers special Hose for certain applications that require electrically conductive Hose. Parker manufactures special Hose for conveying paint in airless paint spraying applications. This Hose is labeled Electrically Conductive Airless Paint Spray Hose on its layline and packaging. This Hose must be properly connected to the appropriate Parker Fittings and properly grounded in order to dissipate dangerous static charge buildup, which occurs in all airless paint spraying applications. Do not use any other Hose for airless paint spraying, even if electrically conductive. Use of any other Hose or failure to properly connect the Hose can cause a fire or an explosion resulting in death, personal injury, and property damage. Parker manufactures a special Hose for certain compressed natural gas ( CNG ) applications where static electricity buildup may occur. Parker CNG Hose assemblies comply with AGA Requirements 1-93, Hoses for Natural Gas Vehicles and Fuel Dispensers. This Hose is labeled Electrically Conductive for CNG Use on its layline and packaging. This Hose must be properly connected to the appropriate Parker Fittings and properly grounded in order to dissipate dangerous static charge buildup, which occurs in, for example, high velocity CNG dispensing or transfer. Do not use any other Hose for CNG applications where static charge buildup may occur, even if electrically conductive. Use of other Hoses in CNG applications or failure to properly connect or ground this Hose can cause a fire or an explosion resulting in death, personal injury, and property damage. Care must also be taken to protect against CNG permeation through the Hose wall. See section 2.6, Permeation, for more information. Parker CNG Hose is intended for dispenser and vehicle use at a maximum temperature of 180 F. Parker CNG Hose should not be used in confined spaces or unventilated areas or areas exceeding 180 F. Final assemblies must be tested for leaks. CNG Hose Assemblies should be tested on a monthly basis for conductivity per AGA 1-93. Parker manufacturers special Hose for aerospace in flight applications. Aerospace in flight applications employing Hose to transmit fuel, lubricating fluids and hydraulic fluids require a special Hose with a conductive inner tube. This Hose for in flight applications is available only from Parker s Stratoflex Products Division. Do not use any other 22

Parker Safety Guide Parker Hose for in flight applications, even if electrically conductive. Use of other Hoses for in flight applications or failure to properly connect or ground this Hose can cause a fire or an explosion resulting in death, personal injury, and property damage. These Hose assemblies for in flight applications must meet all applicable aerospace industry, aircraft engine, and aircraft requirements. 2.2 Pressure: Hose selection must be made so that the published maximum recommended working pressure of the Hose is equal to or greater than the maximum system pressure. Surge pressures or peak transient pressures in the system must be below the published maximum working pressure for the Hose. Surge pressures and peak pressures can usually only be determined by sensitive electrical instrumentation that measures and indicates pressures at millisecond intervals. Mechanical pressure gauges indicate only average pressures and cannot be used to determine surge pressures or peak transient pressures. Published burst pressure ratings for Hose is for manufacturing test purposes only and is no indication that the Product can be used in applications at the burst pressure or otherwise above the published maximum recommended working pressure. 2.3 Suction: Hoses used for suction applications must be selected to insure that the Hose will withstand the vacuum and pressure of the system. Improperly selected Hose may collapse in suction application. 2.4 Temperature: Be certain that fluid and ambient temperatures, both steady and transient, do not exceed the limitations of the Hose. Temperatures below and above the recommended limit can degrade Hose to a point where a failure may occur and release fluid. Properly insulate and protect the Hose Assembly when routing near hot objects (e.g. manifolds). Do not use any Hose in any application where failure of the Hose could result in the conveyed fluids (or vapors or mist from the conveyed fluids) contacting any open flame, molten metal, or other potential fire ignition source that could cause burning or explosion of the conveyed fluids or vapors. 2.5 Fluid Compatibility: Hose Assembly selection must assure compatibility of the Hose tube, cover, reinforcement, and Fittings with the fluid media used. See the fluid compatibility chart in the Parker publication for the product being considered or used. This information is offered only as a guide. Actual service life can only be determined by the end user by testing under all extreme conditions and other analysis. Hose that is chemically compatible with a particular fluid must be assembled using Fittings and adapters containing likewise compatible seals. 2.6 Permeation: Permeation (that is, seepage through the Hose) will occur from inside the Hose to outside when Hose is used with gases, liquid and gas fuels, and refrigerants (including but not limited to such materials as helium, diesel fuel, gasoline, natural gas, or LPG). This permeation may result in high concentrations of vapors which are potentially flammable, explosive, or toxic, and in loss of fluid. Dangerous explosions, fires, and other hazards can result when using the wrong Hose for such applications. The system designer must take into account the fact that this permeation will take place and must not use Hose if this permeation could be hazardous. The system designer must take into account all legal, government, insurance, or any other special regulations which govern the use of fuels and refrigerants. Never use a Hose even though the fluid compatibility is acceptable without considering the potential hazardous effects that can result from permeation through the Hose Assembly. Permeation of moisture from outside the Hose to inside the Hose will also occur in Hose assemblies, regardless of internal pressure. If this moisture permeation would have detrimental effects (particularly, but not limited to refrigeration and air conditioning systems), incorporation of sufficient drying capacity in the system or other appropriate system safeguards should be selected and used. 2.7 Size: Transmission of power by means of pressurized fluid varies with pressure and rate of flow. The size of the components must be adequate to keep pressure losses to a minimum and avoid damage due to heat generation or excessive fluid velocity. 2.8 Routing: Attention must be given to optimum routing to minimize inherent problems (kinking or flow restriction due to Hose collapse, twisting of the Hose, proximity to hot objects or heat sources). 2.9 Environment: Care must be taken to insure that the Hose and Fittings are either compatible with or protected from the environment (that is, surrounding conditions) to which they are exposed. Environmental conditions including but not limited to ultraviolet radiation, sunlight, heat, ozone, moisture, water, salt water, chemicals, and air pollutants can cause degradation and premature failure. 2.10 Mechanical Loads: External forces can significantly reduce Hose life or cause failure. Mechanical loads which must be considered include excessive flexing, twist, kinking, tensile or side loads, bend radius, and vibration. Use of swivel type Fittings or adapters may be required to insure no twist is put into the Hose. Unusual applications may require special testing prior to Hose selection. 2.11 Physical Damage: Care must be taken to protect Hose from wear, snagging, kinking, bending smaller that minimum bend radius, and cutting, any of which can cause premature Hose failure. Any Hose that has been kinked or bent to a radius smaller than the minimum bend radius, and any Hose that has been cut or is cracked or is otherwise damaged, should be removed and discarded. 2.12 Proper End Fitting: See instructions 3.2 through 3.5. These recommendations may be substantiated by testing to industry standards such as SAE J517 for hydraulic applications, or MIL-A-5070, AS1339, or AS3517 for Hoses from Parker s Stratoflex Products Division for aerospace applications. 2.13 Length: When establishing a proper Hose length, motion absorption, Hose length changes due to pressure, and Hose and machine tolerances and movement must be considered. 2.14 Specifications and Standards: When selecting Hose and Fittings, government, industry, and Parker specifications and recommendations must be reviewed and followed as applicable. 2.15 Hose Cleanliness: Hose components may vary in cleanliness levels. Care must be taken to insure that the Hose Assembly selected has an adequate level of cleanliness for the application. 2.16 Fire Resistant Fluids: Some fire resistant fluids that are to be conveyed by Hose require use of the same type of Hose as used with petroleum base fluids. Some such fluids require a special Hose, while a few fluids will not work with any Hose at all. See instructions 2.5 and 1.5. The wrong Hose may fail after a very short service. In addition, all liquids but pure water may burn fiercely under certain conditions, and even pure water leakage may be hazardous. 2.17 Radiant Heat: Hose can be heated to destruction without contact by such nearby items as hot manifolds or molten metal. The same heat source may then initiate a fire. This can occur despite the presence of cool air around the Hose. 2.18 Welding or Brazing: When using a torch or arc-welder in close proximity to hydraulic lines, the hydraulic lines should be removed or shielded with appropriate fire resistant materials. Flame or weld spatter could burn through the Hose and possibly ignite escaping fluid resulting in a catastrophic failure. Heating of plated parts, including Hose Fittings and adapters, above 450 F (232 C) such as during welding, brazing, or soldering may emit deadly gases. 2.19 Atomic Radiation: Atomic radiation affects all materials used in Hose assemblies. Since the long-term effects may be unknown, do not expose Hose assemblies to atomic radiation. 2.20 Aerospace Applications: The only Hose and Fittings that may be used for in flight aerospace applications are Hose available from Parker s Stratoflex Products Division. Do not use any other Hose or Fittings for in flight applications. Do not use any Hose or Fittings from Parker s Stratoflex Products Division with any other Hose or Fittings, unless expressly approved in writing by the engineering manager or chief engineer of Stratoflex Products Division and verified by the user s own testing and inspection to aerospace industry standards. 2.21 Unlocking Couplings: Ball locking couplings or other couplings with disconnect sleeves can unintentionally disconnect if they are dragged over obstructions or if the sleeve is bumped or moved enough to cause disconnect. Threaded couplings should be considered where there is a potential for accidental uncoupling. 3.0 HOSE AND FITTING ASSEMBLY AND INSTALLATION INSTRUC- TIONS 3.1 Component Inspection: Prior to assembly, a careful examination of the Hose and Fittings must be performed. All components must be checked for correct style, size, catalog number, and length. The Hose must be examined for cleanliness, obstructions, blisters, cover looseness, kinks, cracks, cuts or any other visible defects. Inspect the Fitting and sealing surfaces for burrs, nicks, corrosion or other imperfections. Do NOT use any component that displays any signs of nonconformance. 3.2 Hose and Fitting Assembly: Do not assemble a Parker Fitting on a Parker Hose that is not specifically listed by Parker for that Fitting, unless authorized in writing by the engineering manager or chief engineer of the appropriate Parker division. Do not assemble a Parker Fitting on another manufacturers Hose or a Parker Hose on another manufacturers Fitting unless (i) the engineering manager or chief engineer of the appropriate Parker division approves the Assembly in writing or that combination is expressly approved in the appropriate Parker literature for the specific Parker product, and (ii) the user verifies the Assembly and the application through analysis and testing. For Parker Hose that does not specify a Parker Fitting, the user is solely responsible for the selection of the proper Fitting and Hose Assembly procedures. See instruction 1.4. 23

Parker Safety Guide The Parker published instructions must be followed for assembling the Fittings on the Hose. These instructions are provided in the Parker Fitting catalog for the specific Parker Fitting being used, or by calling 1-800-CPARKER, or at www.parker.com. 3.3 Related Accessories: Do not crimp or swage any Parker Hose or Fitting with anything but the listed swage or crimp machine and dies in accordance with Parker published instructions. Do not crimp or swage another manufacturers Fitting with a Parker crimp or swage die unless authorized in writing by the engineering manager of chief engineer of the appropriate Parker division. 3.4 Parts: Do not use any Parker Fitting part (including but not limited to socket, shell, nipple, or insert) except with the correct Parker mating parts, in accordance with Parker published instructions, unless authorized in writing by the engineering manager or chief engineer of the appropriate Parker division. 3.5 Field Attachable/Permanent: Do not reuse any field attachable (Field Attachable) Hose Fitting that has blown or pulled off a Hose. Do not reuse a Parker permanent Hose Fitting (crimped or swaged) or any part thereof. Complete Hose Assemblies may only be reused after proper inspection under section 4.0. Do not assemble Fittings to any previously used hydraulic Hose that was in service, for use in a fluid power application. 3.6 Pre-Installation Inspection: Prior to installation, a careful examination of the Hose Assembly must be performed. Inspect the Hose Assembly for any damage or defects. Do NOT use any Hose Assembly that displays any signs of nonconformance. 3.7 Minimum Bend Radius: Installation of a Hose at less than the minimum listed bend radius may significantly reduce the Hose life. Particular attention must be given to preclude sharp bending at the Hose to Fitting juncture. Any bending during installation at less than the minimum bend radius must be avoided. If any Hose is kinked during installation, the Hose must be discarded. 3.8 Twist Angle and Orientation: Hose Assembly installation must be such that relative motion of machine components does not produce twisting. 3.9 Securement: In many applications, it may be necessary to restrain, protect, or guide the Hose to protect it from damage by unnecessary flexing, pressure surges, and contact with other mechanical components. Care must be taken to insure such restraints do not introduce additional stress or wear points. 3.10 Proper Connection of Ports: Proper physical installation of the Hose Assembly requires a correctly installed port connection insuring that no twist or torque is transferred to the Hose when the Fittings are being tightened or otherwise during use. 3.11 External Damage: Proper installation is not complete without insuring that tensile loads, side loads, kinking, flattening, potential abrasion, thread damage, or damage to sealing surfaces are corrected or eliminated. See instruction 2.10. 3.12 System Checkout: All air entrapment must be eliminated and the system pressurized to the maximum system pressure (at or below the Hose maximum working pressure) and checked for proper function and freedom from leaks. Personnel must stay out of potential hazardous areas while testing and using. 3.13 Routing: The Hose Assembly should be routed in such a manner so if a failure does occur, the escaping media will not cause personal injury or property damage. In addition, if fluid media comes in contact with hot surfaces, open flame, or sparks, a fire or explosion may occur. See section 2.4. 4.0 HOSE AND FITTING MAINTENANCE AND REPLACEMENT INSTRUCTIONS 4.1 Even with proper selection and installation, Hose life may be significantly reduced without a continuing maintenance program. The severity of the application, risk potential from a possible Hose failure, and experience with any Hose failures in the application or in similar applications should determine the frequency of the inspection and the replacement for the Products so that Products are replaced before any failure occurs. A maintenance program must be established and followed by the user and, at minimum, must include instructions 4.2 through 4.7. 4.2 Visual Inspection Hose/Fitting: Any of the following conditions require immediate shut down and replacement of the Hose Assembly: Fitting slippage on Hose, Damaged, cracked, cut or abraded cover (any reinforcement exposed); Hard, stiff, heat cracked, or charred Hose; Cracked, damaged, or badly corroded Fittings; Leaks at Fitting or in Hose; Kinked, crushed, flattened or twisted Hose; and Blistered, soft, degraded, or loose cover. 4.3 Visual Inspection All Other: The following items must be tightened, repaired, corrected or replaced as required: Leaking port conditions; Excess dirt buildup; Worn clamps, guards or shields; and System fluid level, fluid type, and any air entrapment. 4.4 Functional Test: Operate the system at maximum operating pressure and check for possible malfunctions and leaks. Personnel must avoid potential hazardous areas while testing and using the system. See section 2.2. 4.5 Replacement Intervals: Hose assemblies and elastomeric seals used on Hose Fittings and adapters will eventually age, harden, wear and deteriorate under thermal cycling and compression set. Hose Assemblies and elastomeric seals should be inspected and replaced at specific replacement intervals, based on previous service life, government or industry recommendations, or when failures could result in unacceptable downtime, damage, or injury risk. See section 1.2. 4.6 Hose Inspection and Failure: Hydraulic power is accomplished by utilizing high-pressure fluids to transfer energy and do work. Hoses, Fittings, and Hose Assemblies all contribute to this by transmitting fluids at high pressures. Fluids under pressure can be dangerous and potentially lethal and, therefore, extreme caution must be exercised when working with fluids under pressure and handling the Hoses transporting the fluids. From time to time, Hose Assemblies will fail if they are not replaced at proper time intervals. Usually these failures are the result of some form of misapplication, abuse, wear, or failure to perform proper maintenance. When Hoses fail, generally the high-pressure fluids inside escape in a stream which may or may not be visible to the user. Under no circumstances should the user attempt to locate the leak by feeling with their hands or any other part of their body. High-pressure fluids can and will penetrate the skin and cause severe tissue damage and possibly loss of limb. Even seemingly minor hydraulic fluid injection injuries must be treated immediately by a physician with knowledge of the tissue damaging properties of hydraulic fluid. If a Hose failure occurs, immediately shut down the equipment and leave the area until pressure has been completely released from the Hose Assembly. Simply shutting down the hydraulic pump may or may not eliminate the pressure in the Hose Assembly. Many times check valves, etc., are employed in a system and can cause pressure to remain in a Hose Assembly even when pumps or equipment are not operating. Tiny holes in the Hose, commonly known as pinholes, can eject small, dangerously powerful but hard to see streams of hydraulic fluid. It may take several minutes or even hours for the pressure to be relieved so that the Hose Assembly may be examined safely. Once the pressure has been reduced to zero, the Hose Assembly may be taken off the equipment and examined. It must always be replaced if a failure has occurred. Never attempt to patch or repair a Hose Assembly that has failed. Consult the nearest Parker distributor or the appropriate Parker division for Hose Assembly replacement information. Never touch or examine a failed Hose Assembly unless it is obvious that the Hose no longer contains fluid under pressure. The high-pressure fluid is extremely dangerous and can cause serious and potentially fatal injury. 4.7 Elastomeric seals: Elastomeric seals will eventually age, harden, wear and deteriorate under thermal cycling and compression set. Elastomeric seals should be inspected and replaced. 4.8 Refrigerant gases: Special care should be taken when working with refrigeration systems. Sudden escape of refrigerant gases can cause blindness if the escaping gases contact the eye and can cause freezing or other severe injuries if it contacts any other portion of the body. 4.9 Compressed natural gas (CNG): Parker CNG Hose Assemblies should be tested after installation and before use, and at least on a monthly basis per AGA 1-93 Section 4.2 Visual Inspection Hose/Fitting. The recommended procedure is to pressurize the Hose and check for leaks and to visually inspect the Hose for damage. Caution: Matches, candles, open flame or other sources of ignition shall not be used for Hose inspection. Leak check solutions should be rinsed off after use. 24

Notes 25

Offer of Sale 1. Terms and Conditions of Sale: All descriptions, quotations, proposals, offers, acknowledgments, acceptances and sales of Sellerʼs products are subject to and shall be governed exclusively by the terms and conditions stated herein. Buyerʼs acceptance of any offer to sell is limited to these terms and conditions. Any terms or conditions in addition to, or inconsistent with those stated herein, proposed by Buyer in any acceptance of an offer by Seller, are hereby objected to. No such additional, different or inconsistent terms and conditions shall become part of the contract between Buyer and Seller unless expressly accepted in writing by Seller. Sellerʼs acceptance of any offer to purchase by Buyer is expressly conditioned upon Buyerʼs assent to all the terms and conditions stated herein, including any terms in addition to, or inconsistent with those contained in Buyerʼs offer. Acceptance of Sellerʼs products shall in all events constitute such assent. 2. Payment: Payment shall be made by Buyer net 30 days from the date of delivery of the items purchased hereunder. Amounts not timely paid shall bear interest at the rate of 1-1/2% for each month or a portion thereof that Buyer is late in making payment. Any claims by Buyer for omissions or shortages in a shipment shall be waived unless Seller receives notice thereof within 30 days after Buyerʼs receipt of the shipment. 3. Delivery: Unless otherwise provided on the face hereof, delivery shall be made F.O.B. Sellerʼs plant. Regardless of the method of delivery, however, risk of loss shall pass to Buyer upon Sellerʼs delivery to a carrier. Any delivery dates shown are approximate only and Seller shall have no liability for any delays in delivery. 4. Warranty: Seller warrants that the items sold hereunder shall be free from defects in materials or workmanship for a period of 365 days from the date of shipment to Buyer, or 2,000 hours of use, whichever expires first. THIS WARRANTY COM- PRISES THE SOLE AND ENTIRE WARRANTY PERTAINING TO ITEMS PROVIDED HEREUNDER. SELLER MAKES NO OTHER WARRANTY, GUARANTEE, OR REPRESENTATION OF ANY KIND WHATSOEVER. ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO, MER- CHANTABILITY AND FITNESS FOR PURPOSE, WHETHER EXPRESS, IMPLIED, OR ARISING BY OPERATION OF LAW, TRADE USAGE, OR COURSE OF DEALING ARE HEREBY DISCLAIMED. NOTWITHSTANDING THE FOREGOING, THERE ARE NO WARRANTIES WHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY OR PAR- TIALLY, TO BUYER S DESIGNS OR SPECIFICATIONS. 5. Limitation Of Remedy: SELLER S LIABILITY ARISING FROM OR IN ANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS CONTRACT SHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT OF THE ITEMS SOLD, OR REFUND OF THE PURCHASE PRICE PAID BY BUYER, AT SELLER S SOLE OPTION. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY KIND OR NATURE WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING FROM OR IN ANY WAY CONNECTED WITH THIS AGREEMENT OR ITEMS SOLD HEREUNDER, WHETHER ALLEGED TO ARISE FROM BREACH OF CONTRACT, EX- PRESS OR IMPLIED WARRANTY, OR IN TORT, INCLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURE TO WARN OR STRICT LIABILITY. 6. Changes, Reschedules and Cancellations: Buyer may request to modify the designs or specifications for items sold hereunder as well as the quantities and delivery dates thereof, or may request to cancel all or part of an order, however, no such requested modification or cancellation shall become part of the contract between Buyer and Seller unless accepted by Seller in a written amendment to this Agreement. Acceptance of any such requested modification of cancellation shall be at Sellerʼs discretion, and shall be upon such terms and conditions as Seller may require. 7. Special Tooling: A tooling charge may be imposed for any special tooling, including without limitation, dies, fixtures, molds and patterns, acquired to manufacture items sold pursuant to this contract. Such special tooling shall be and remain Sellerʼs property notwithstanding payment of any charges therefor by Buyer. In no event will Buyer acquire any interest in apparatus belonging to Seller which is utilized in the manufacture of the items sold hereunder, even if such apparatus has been specially converted or adapted for such manufacture and notwithstanding any charges paid by Buyer therefor. Unless otherwise agreed, Seller shall have the right to alter, discard or otherwise dispose of any special tooling or other property in its sole discretion at any time. 8. Buyer s Property: Any designs, tools, patterns, materials, drawings, confidential information or equipment furnished to Seller by Buyer, or any other items which become Buyerʼs property, may be considered obsolete and may be destroyed by Seller after two (2) consecutive years have elapsed without Buyer placing an order for the items which are manufactured using such property. Seller shall not be responsible for any loss or damage to such property while it is in Sellerʼs possession or control. 9. Taxes: Unless otherwise indicated, all prices and charges are exclusive of excise, sales, use, property, occupational or like taxes which may be imposed by any taxing authority upon the manufacture, sale or delivery of the items sold hereunder. If any such taxes must be paid by Seller, or if Seller is liable for the collection of such tax, the amount thereof shall be in addition to the amounts for the items sold. Buyer agrees to pay all such taxes or to reimburse Seller therefor upon receipt of its invoice. If Buyer claims exemption from any sales, use or other tax imposed by any taxing authority, Buyer shall save Seller harmless from and against any such tax, as well as any interest or penalties thereon which may be assessed if the items are held to be taxable. 10. Indemnity For Infringement of Intellectual Property Rights: Seller shall have no liability for infringement of any patents, trademarks, copyrights, trade dress, trade secrets or similar rights except as provided in this Part 10. Seller will defend and indemnify Buyer against allegations of infringement of U.S. patents, U.S. trademarks, copyrights, trade dress and trade secrets (hereinafter ʻIntellectual Property Rightsʼ). Seller will defend at its expense and will pay the cost of any settlement or damages awarded in an action brought against Buyer based on an allegation that an item sold pursuant to this contract infringes the Intellectual Property Rights of a third party. Sellerʼs obligation to defend and indemnify Buyer is contingent on Buyer notifying Seller within ten (10) days after Buyer becomes aware of such allegations of infringement, and Seller having sole control over the defense of any allegations or actions, including all negotiations for settlement or compromise. If an item sold hereunder is subject to a claim that it infringes the Intellectual Property Rights of a third party, Seller may, at its sole expense and option, procure for Buyer the right to continue using said item, replace or modify said item so as to make it noninfringing, or offer to accept return of said item and return the purchase price less a reasonable allowance for depreciation. Notwithstanding the foregoing, Seller shall have no liability for claims of infringement based on information provided by Buyer, or directed to items delivered hereunder for which the designs are specified in whole or part by Buyer, or infringements resulting from the modification, combination or use in a system of any item sold hereunder. The foregoing provisions of this Part 10 shall constitute Sellerʼs sole and exclusive liability and Buyerʼs sole and exclusive remedy for infringement of Intellectual Property Rights. If a claim is based on information provided by Buyer or if the design for an item delivered hereunder is specified in whole or in part by Buyer, Buyer shall defend and indemnify Seller for all costs, expenses or judgements resulting from any claim that such item infringes any patent, trademark, copyright, trade dress, trade secret or any similar right. 11. Force Majeure: Seller does not assume the risk of and shall not be liable for delay or failure to perform any of Sellerʼs obligations by reason of circumstances beyond the reasonable control of Seller (hereinafter ʻEvents of Force Majeureʼ). Events of Force Majeure shall include without limitation, accidents, acts of God, strikes or labor disputes, acts, laws, rules or regulations of any government or government agency, fires, floods, delays or failures in delivery of carriers or suppliers, shortages of materials and any other cause beyond Sellerʼs control. 12. Entire Agreement/Governing Law: The terms and conditions set forth herein, together with any amendments, modifications and any different terms or conditions expressly accepted by Seller in writing, shall constitute the entire Agreement concerning the items sold, and there are no oral or other representations or agreements which pertain thereto. This Agreement shall be governed in all respects by the law of the State of Ohio. No actions arising out of the sale of the items sold hereunder or this Agreement may be brought by either party more than two (2) years after the cause of action accrues. The items described in this document are hereby offered for sale at prices to be established by, its subsidiaries and its authorized distributors. This offer and its acceptance by any customer ( Buyer ) shall be governed by all of the following Terms and Conditions. Buyerʼs order for any item described in this document, when communicated to, its subsidiary or an authorized distributor ( Seller ) verbally or in writing, shall constitute acceptance of this offer. 26

6035 Parkland Blvd. Cleveland, Ohio 44124-4141 Telephone: (216) 896-3000 Fax: (216) 896-4000 www.parker.com About Parker Hannifin is a leading global motion-control company dedicated to delivering premier customer service. A Fortune 500 corporation listed on the New York Stock Exchange (PH), our components and systems comprise over 1,400 product lines that control motion in some 1,000 industrial and aerospace mar-kets. Parker is the only manufacturer to offer its customers a choice of hydraulic, pneumatic, and electromechanical motion-control solutions. Our Company has the largest distribution network in its field, with over 7,500 distributors serving nearly 400,000 customers worldwide. Parker s Charter To be a leading worldwide manufacturer of compo-nents and systems for the builders and users of durable goods. More specifically, we will design, market and manufacture products controlling motion, flow and pressure. We will achieve profitable growth through premier customer service. Product Information North American customers seeking product information, the location of a nearby distributor, or repair services will receive prompt attention by calling the Parker Product Information Center at our toll-free number: 1-800-C-PARKER (1-800-272-7537). In Europe, call 00800-C-PARKER-H (00800-2727-5374). The Aerospace Group is a leader in the development, design, manufacture and servicing of control systems and components for aerospace and related high-technology markets, while achieving growth through premier customer service. The Climate & Industrial Controls Group designs, manufactures and markets system-control and fluidhandling components and systems to refrigeration, airconditioning and industrial customers worldwide. The Fluid Connectors Group designs, manufactures and markets rigid and flexible connectors, and associated products used in pneumatic and fluid systems. The Seal Group designs, manufactures and distributes industrial and commercial sealing devices and related products by providing superior quality and total customer satisfaction. The Hydraulics Group designs, produces and markets a full spectrum of hydraulic components and systems to builders and users of industrial and mobile machinery and equipment. The Filtration Group designs, manufactures and markets quality filtration and clarification products, providing customers with the best value, quality, technical support, and global availability. The Automation Group is a leading supplier of pneumatic and electromechanical components and systems to automation customers worldwide. The Instrumentation Group is a global leader in the design, manufacture and distribution of high-quality critical flow components for worldwide process instrumentation, ultra-high-purity, medical and analytical applications.