[ACT 050] Manual E 4/4/06 4:34 PM Page 1 Cordless INFLATION STATION OWNER S MANUAL MODEL NO: RCP-C65B KEEP THE ORIGINAL BOX, PACKAGING AND RECEIPT. BEFORE OPERATING THIS UNIT, READ THE MANUAL THOROUGHLY AND RETAIN IT FOR FUTURE REFERENCE.
[ACT 050] Manual E 4/4/06 4:34 PM Page 2 Cordless INFLATION STATION HIGH-PRESSURE APPLICATIONS Car tires Bicycle tires Basketball Sporting equipment Party balloons HIGH-VOLUME APPLICATIONS Air mattresses Rafts Inflatable toys Pool toys 1
[ACT 050] Manual E 4/4/06 4:34 PM Page 3 1 3 2 4 5 6 7 8 9 Accessories include: 10 11 12 16 13 14 15 PARTS LIST ITEM NO. QTY DESCRIPTION 1 1 High-pressure air compressor 2 1 High-volume air inflator 3 1 Digital tire gauge 4 1 Ni-Cd rechargable battery 5 1 Ni-Cd rechargable battery 6 1 12V cigarette lighter adapter pack 7 1 Charger station 8 1 Stand 9 1 Pressure gauge hose ITEM NO. QTY DESCRIPTION 10 1 Large adapter 11 1 Medium adapter 12 1 Inflatable connector 13 1 Ball adapter 14 1 Small adapter 15 1 Balloon adapter 16 1 AC charger www.activeproducts.com 2
[ACT 050] Manual E 4/4/06 4:34 PM Page 4 DIGITAL TIRE GAUGE LCD display LED light ON/OFF switch LED light switch USER INSTRUCTION: 1. Press ON/OFF button once to switch on. 2. To choose desired pressure format PSI, BAR, press the ON/OFF button. 3. Press nozzle on tire s valve stem. 4. Hold until pressure reading is displayed on LCD display. 5. Press button and hold for 5 second to switch off. 6. To take another pressure reading, simply repeat steps 3 to 4. 7. 1 x 3V Lithium button cell, CR2032. Note: Digital gauge accurate to ± 1 PSI 3
[ACT 050] Manual E 4/4/06 4:34 PM Page 5 INSTALLATION PROCEDURE DESKTOP PLACEMENT 1Pull out the bracket as shown on the back of the charger station. Red LED Indicator AC Charging Port 2Seat the charger station on a flat surface. Connect the AC charger and return all components back onto the charger station. www.activeproducts.com 4
[ACT 050] Manual E 4/4/06 4:34 PM Page 6 POWER SOURCE Both the air compressor and air inflator can be powered by both the Ni-Cd rechargeable battery and the 12V cigarette lighter adapter. RECHARGEABLE BATTERIES The Inflation Station comes with two 9.6V 1,000 mah Ni-Cd rechargeable battery. The battery can be charged either on the charger station, or from the AC charger port on the battery. CHARGING BATTERY ON THE CHARGER STATION Before initial use, place one of the batteries on the charger station for an initial charge time of 15 to 18 hours. Repeat charging times are approximately 20-22 hours, if batteries are depleted. Warning! Failure to fully charge the battery will result in shorter life, compromised performance and will void battery warranty. To keep the battery fully charged at all times, place charged at all times, place the battery on the charger station whenever they are not in use. The charger station red LED indicator will be ON once the battery has been properly on the station. The charger station will control battery charging to ensure optimal battery charge. We recommend that if the inflation station is not going to be used for an extended period of time (i.e. 4 months or more), the unit should be unplugged and stored indoors. When the inflation station is removed from storage, please re-charge for 20 to 22 hours before use. CHARGING FROM THE AC CHARGER PORT ON THE BATTERY Remove the battery from the air compressor/inflator by gripping the end of the battery and pulling it out. The same AC charger can be used to charge the battery directly by connecting the AC charger to AC charger port on the battery and plugging the AC charger to an 110V-120V power source. The red LED indicator will be ON when the battery is charging. When charging directly from the AC charger port on the battery, the charging time must not exceed 24 hours. Repeat charging times are approximately 18-20 hours, if the battery is depleted. STEP 1 STEP 2 AC Charger Port 5
[ACT 050] Manual E 4/4/06 4:34 PM Page 7 TYPICAL RUN-TIME* DEVICE Air Compressor Air Inflator * REMARK: TYPICAL RUN-TIME* 10-15 minutes 15-20 minutes 1. Typical run-time will vary depending on the battery level, pressure load during use, and the operating conditions. 2. High-pressure loading, or excessive back pressure will result in a shorter run-time than indicated above. 3. Cold temperature conditions will reduce battery run-time. We recommend using the 12V cigarette lighter adapter pack during cold temperature operating conditions. 12V CIGARETTE LIGHTER ADAPTER PACK Switching between the battery and 12V cigarette lighter adapter pack Roll out the 12V cord before use. Remove the battery from the air compressor/inflator by gripping the end of the battery and pulling it out. Slide the 12V adapter pack into the air compressor/inflator until clicks into place. Make sure that the cord runs through the small hole at the base of the cable pack. Connect the 12V car cigarette lighter adapter to the cigarette lighter socket in your car. When the operating period per charge is significantly reduced, it indicates the battery is worn-out and should be replaced. To order a replacement battery, please visit us at www.activeproducts.com www.activeproducts.com 6
[ACT 050] Manual E 4/4/06 4:34 PM Page 8 INFLATION INSTRUCTION HIGH-PRESSURE AIR COMPRESSOR Balloon adapter Ball adapter Pressure gauge hose B A Loosen (counterclockwise) B Tighten (clockwise) A The Air Compressor has been specially designed for simple and fast inflation of car tires, bicycle tires, basketball, sporting equipment, and party balloons. The air compressor provides a small quantity of air at a relatively high pressure. INFLATING A CAR TIRE AND BICYCLE TIRE 1. Loosen the union valve from the air nozzle. 2. Insert the pressure gauge hose into the air nozzle and tighten the union valve. 3. Screw the thread connector onto tire s valve stem. 4. Press the trigger once for continuous inflation. 5. Operate the air compressor until the desired pressure is reached. 6. Pressure the trigger twice to stop inflation. 7. Remove the thread connector from the tire. Note: To avoid over-inflation of tires, please check the recommended car tire pressure in the vehicle s owner s manual. For bicycle tire, please check the tire marking. INFLATING SPORTING EQUIPMENT (I.E. BASKETBALL) OR PARTY BALLOONS 1. Loosen the union valve from the air nozzle. 2. Insert the ball/balloon adapter into the air nozzle and tighten the union valve. 3. Insert the ball/balloon adapter into valve of the object to be inflated. 4. Operate the air compressor until the object is fully inflated. 5. Remove ball/balloon adapter from the inflated object s valve. Note: If a pressure reading is required during inflation, use the pressure gauge hose provided. CAUTION Do not run the air compressor continuously for more than 15 minutes. After each 15 minutes, allow it to cool for a minimum of 15 minutes. Do not leave the air compressor unattended while in operation. Keep out of reach of children. Do not exceed maximum pressure of 150 psi. The pressure gauge will provide an estimated reading only. Please use a digital pressure gauge for more accuracy pressure information. 7
[ACT 050] Manual E 4/4/06 4:34 PM Page 9 HIGH-VOLUME AIR INFLATOR Inflation outlet Large adapter Inflatable connector Medium adapter Deflation outlet Small adapter The Air Inflator is designed for quick and easy inflation and deflation of high air volume objects such as air mattresses, rafts, inflatable toys and pool toys. BEFORE INFLATING Choose the appropriate inflatable adapter. There are four inflatable adapters provided for high-volume inflation/deflation. The small and medium adapters must be used with the inflatable connector provided. The inflatable connector and large adapter can be directly attached to the inflation air outlet. INFLATING PROCEDURE 1. Insert the appropriate inflatable adapter into inflation outlet. 2. Insert adapter into the air valve of the object to be inflated. 3. Press the trigger once for continuous inflation. 4. Operate the air inflator until the desired firmness is reached. 5. Pressure the trigger twice to stop inflation. 6. Remove adapter from the inflated object valve and close the valve cap. DEFLATING PROCEDURE 1. Insert the inflatable adapter into deflation outlet. 2. Insert adapter into the valve of the object to be deflated. 3. Press the trigger once for continuous deflation. 4. Operate the air inflator until desired deflation is reached. 5. Pressure the trigger twice to stop deflation. 6. Remove adapter from the deflated object valve. Note: Make sure the stop valve or resisted valve is opened, before inflation or deflation. INFLATION TIPS FOR LARGE OBJECTS: The performance of an air inflator depends on air flow rate, size of adapter and the valve of the inflatable object. The smaller the valve and/ or adapter used, the lower the air flow rate. Therefore, always buy inflatable objects with the largest possible valves. Typically, air mattresses or large inflatable objects may have two sizes of air valve, always inflate from the largest valve to get maximum performance. CAUTION Do not run the air inflator for continuously for more than 15 minutes. After each 15 minutes, allow it to cool for a minimum of 15 minutes. Do not leave the air inflator unattended while in operation. Keep out of reach of children. Make sure the stop valve or resisted valve is opened, before inflation or deflation. www.activeproducts.com 8
[ACT 050] Manual E 4/4/06 4:34 PM Page 10 GENERAL SAFETY MEASURES AND PRECAUTIONS THAT APPLY TO THE USE OF AIR COMPRESSOR/INFLATOR. The following instructions apply to both the air compressor and air inflator. Safe operation of the air compressor and inflator require that you read the instructions and safety precautions carefully and follow all instructions before using the air compressor or inflator. 1. The air compressor and inflator are designed for occasional use. Inflation over a long period will overheat the air compressor or air inflator and may cause damage. 2. The air compressor and inflator must not operate for more than 15 minutes at a time, after which it must be switched off and set aside to cool for at least 15 minutes before restarting. 3. If the air compressor or inflator emits abnormal sounds or overheats, turn it off immediately and let it cool off for minimum 30 minutes. 4. Inspect air compressor, inflator and batteries before use. If cracked, broken or damaged parts are found, qualified technicians should repair damaged parts. 5. Incorrect use of air compressor/inflator may result in personal injury and/or property damage. 6. Never expose the air compressor, inflator or battery to rain, frost or temperatures above 50 ºC (122 ºF). Never charge the battery in humid or wet locations. 7. Never use the air compressor or inflator near flammable fluids or gases. Make sure your working area is well-lit. 8. Protect yourself against electric shock. Avoid physical contact with grounded surfaces such as pipes, radiators, electric stoves, refrigerators, etc. 9. Never allow children to connect/disconnect the air compressor or inflator to/from power sources. Never leave children unattended with the air compressor or inflator and never allow them to play with the accessories. 10. Never allow anyone to pump air into mouth, ears, nose, etc of people, or animals. The air compressor/inflator is not a toy. 11. Store air compressor and inflator in a secure location. If the air compressor/inflator for long periods of time, it should be stored in a dry space inaccessible to children. 12. Regularly check the charger cord. Never carry the charger by the cord and never pull the plug out of the outlet by jerking the cord. Make sure the cord is not exposed to hot objects, oil or sharp edges. 13. Keep the air compressor and inflator clean to maintain maximum output and safety. Examine the plug, charger and cable pack at regular intervals and have them repaired by qualified technicians if they are damaged. 14. Unplug the 12V car cigarette lighter adapter from the cigarette lighter socket in your car when is not in use. 15. Unplug the AC charger from the battery when the charger is not in use. 16. Never charge the battery outdoors. Do not open the battery. Protect it against impact. The battery should be stored in a dry, frost-free place. 17. The battery and charger are designed for each other. Only an Active Products charger should be used. 18. Protect the battery against heat and fire to prevent danger due to explosion! 19. Do not place the battery on a heater and do not expose it to solar radiation for a prolonged period. Exposing battery to temperatures above 50 ºC (122 ºF) will damage the battery. Allow batteries to cool off completely before charging. 20. Do not directly connect the positive (+) and the negative (-) terminals. This will result in a short-circuit caused by metallic arcing. 21. Stay alert. Always pay attention to what you are doing when working with the air compressor, inflator, charger and battery. 22. Warning! For your own safety, you should only use accessories and parts specified in the instructions, or recommended for use by the manufacturer. Use of accessories and other parts that are not mentioned in the instructions may entail an increased risk for the user of the air compressor and inflator. 9
[ACT 050] Manual E 4/4/06 4:34 PM Page 11 BATTERIES AND THE ENVIRONMENT The accompanying batteries can be recharged at least 500 times, when it is time to replace the batteries, please consider the environment. The EPA certified RBRC Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery indicates that Active Products is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful life, when taken out of service in the United States or Canada. The RBRC program provides a convenient alternative to placing used Ni-Cd batteries into trash or the municipal waste stream. Please call 1-800-822-8837 for information on Ni-Cd battery recycling and disposal bans/restrictions in your area. Active Products involvement in this program is part of our commitment to preserving our environment and conserving our natural resources. WARRANTY This Active Products equipment carries a one (1) year limited warranty against defects in man ufacturing workmanship, and a one-year limited warranty on the batteries and accessories. This Limited Warranty shall be limited to the repair or replacement of parts which prove defective under normal use and service and which on examination shall indicate, to Active Product s satisfaction, they are defective. Active Products reserves the right to request the return of defective parts. Shipping charges may apply. Before returning any parts, contact us by visiting www.activeproducts.com. If Active Products confirms the defect and approves the claim, Active Products will elect to replace such parts without charge. The foregoing warranty does not apply to defects resulting from faulty installation, operation, disassembly, alterations or remodeling, or misuse, misapplication, neglect, abuse, accident, tornado, hurricane, and earthquake; or lack of proper maintenance, cleaning and care. Warranty will not apply if this product is used for commercial or rental purposes. This warranty shall not extend to anyone other than the original purchaser of this product. Should this product become defective within the stated warranty period, do not return to store, but contact us at www.activeproducts.com The warranty card is not a replacement for the proof of purchase. Please keep your proof of purchase in a secure place. www.activeproducts.com 10
[ACT 050] Manual E 4/4/06 4:34 PM Page 12 Cordless INFLATION STATION Imported by: Active Products Inc. Toronto, Ontario, Canada M3B 2M3 www.activeproducts.com Made in China 0306